Replies continued
texkidSugar Land, TX · Jul 23, 2009#401That list will be very helpful whenever someone is looking for the stalk on ebay. There are SO MANY pre-1996 stalks on eBay. So one really has to sift through the listings to find the right stalk. Of course, if you have the money and time, one could always just go to the dealership or TRDSparks and just order the right part. I ordered the Cruise Control Clutch Switch from Sparks and I might end up ordering the wiring from them as well.
BTW, just so ya'll know. My local dealership was charging $40 for one wiperblade assembly. I called TRDSparks and ordered the driver and passenger wiper blades plus the clutch switch all for just under $50 including shipping! Freaking awesome!
toddoSwansboro, NC · Jul 23, 2009#402Just finished this mod on my '09 LB 5-speed. Works great! Big thanks to everyone that provided part numbers and ebay links.
Vince87Montreal, Qc, Canada · Jul 24, 2009#403Just drove to work with my newly working cruise control, this is amazing ! thanks a hundred times CTScott ! So it's now confirmed that the mod works on the Canadian model of the yaris (mine is a 07 MT liftback)... Next step is to install the Clutch Switch and the On/Off LED !
ehud42Winnipeg, MB · Jul 24, 2009#404D'Oh! Why didn't I find this thread 3 weeks earlier.... Just got back from a 2 week, 5,000km road trip in my 2009 Yaris sedan (5 speed) - without cruise... Loved the car, but my back and legs were soar from the hours of driving.
On a plus side, my mileage was low 6's / 100km and even a couple of 5's in the mountains (less then 90kph). I think in mpg (imperial/cdn gallon) that works out to 45-47 with one of my fill ups tipping past 55mpg!
I am very tempted. I have not read any comments regarding warranty. I suspect that any damage caused by installing or using these methods would not be covered, but would the warranty be voided if a mechanic saw this?
If I do the mod, I'll probably put the switches in the holes cut out for seat warmers - down by the gear shifter / hand-brake.
$10 for the bits, plus a clutch switch and my '09 is good to go, eh?
I am so tempted....
PatrickJohnsonMurfreesboro, TN · Jul 24, 2009#405at least in the U.S...
WARRANTY CLAIMS CANNOT BE DENIED UNLESS THE DEALER CAN PROVE WITH CERTAINTY THAT THE MOD DIRECTLY CAUSED WHATEVER FAILURE IS BEING PRESENTED FOR WARRANTY REPAIR....
The burden of proof for denial of warranty claims is on the dealer in U.S., can't imagine Canada being much different.
texkidSugar Land, TX · Jul 27, 2009#406I found this
DIY post on
ToyotaNation. Granted, it was done in 2006 and it was a Tacoma. But after viewing the pictures, they OEM stalk install looks a lot like ours, plus he skims over the Clutch Switch install. And I mean "skim". Like two pictures and thats it. I need something better than that.
Here is the LINK to that thread. I just received my stalk from eBay and the wire should be here by the end of the week. I promise guys, if I can get this done, I'll post a DIY for our Yarii with clearer pictures. Y'all know how OCD-ish I am about DIY pictures.
CtrlAltDefeatIndianapolis IN · Jul 28, 2009#407 Originally Posted by
texkid ↑ I just received my stalk from eBay and the wire should be here by the end of the week. I promise guys, if I can get this done, I'll post a DIY for our Yarii with clearer pictures. Y'all know how OCD-ish I am about DIY pictures.
I'm looking forward to that, I won't attempt it on mine until I see a DIY for a 2008, since it's not pre-wired for cruise, and I really want to use a stalk, not a homemade button setup...
CTScottUSA, CT · Jul 28, 2009#408I finally found the info on the correct terminal with the waterproof sleeve for the ECM connection. It is the female terminal with the waterproof sleeve and 500mm of wire attached. It is intended to be a repair item for a damaged terminal, where the tech just has to splice the wire, rather than having to deal with attaching the wire properly to the terminal.
The part number is: 82998-24250
texkidSugar Land, TX · Jul 28, 2009#409 Originally Posted by
CtrlAltDefeat ↑ I'm looking forward to that, I won't attempt it on mine until I see a DIY for a 2008, since it's not pre-wired for cruise, and I really want to use a stalk, not a homemade button setup...
I am going by what CTScott said in the conversation below...If what you're saying is true, then I am going to need a little more time to figure it out.
Originally Posted by
Henry G. ↑ Just to confirm after reading 24 pages.....this will work on an '08 MT but you need the stalk, the clutch switch and need to do some wiring to the fuse box, correct?
Originally Posted by
CTScott ↑ Correct. We really need to do a DIY for 07-08's...
CTScottUSA, CT · Jul 28, 2009#410 Originally Posted by
texkid ↑ I am going by what CTScott said in the conversation below...If what you're saying is true, then I am going to need a little more time to figure it out.
We need to DIY, so that all of the info is concisely packaged.
Doing an 07-08 is really not difficult, and quite a few have already done it.
I would just like to get the soup to nuts of it nicely documented, so that everyone's questions are pre-answered. I have been meaning to write one up myself from the pictures that nickhjort sent me when he did his, but I haven't had a chance.
texkidSugar Land, TX · Jul 28, 2009#411 Originally Posted by
CTScott ↑ We need to DIY, so that all of the info is concisely packaged.
Doing an 07-08 is really not difficult, and quite a few have already done it.
I would just like to get the soup to nuts of it nicely documented, so that everyone's questions are pre-answered. I have been meaning to write one up myself from the pictures that nickhjort sent me when he did his, but I haven't had a chance.
No problem. I just need the wire assembly from TRD Sparks. If I do get it by Friday or Saturday, I will be doing it right then and there.
texkidSugar Land, TX · Jul 30, 2009#412Okay...I am at a lost.
I received the wire from TRDSparks. I installed the cruise control switch and the clutch switch. Nothing is turning on or engaging. I then jumped the wires in the fuse box to bypass the clutch switch...still nothing. I then took off the airbag again and double-checked the wires, everything is locked in.....still nothing. I even connected the white wire to the purple wire and found out that it starts the car!! I am not getting any "Check Engine" or "Airbag" lights in the cluster, so that's a plus I guess.
Could I possibly just have a bad cruise control switch or am I missing something?
If y'all have any ideas, I am all ears.
ADDED CORRECTION: Umm....I think I just screwed up....I have the '08 LB, so I had to connect a blue wire from the ECM to the connection behind the steering wheel, right?
CTScottUSA, CT · Jul 30, 2009#413 Originally Posted by
texkid ↑ ADDED CORRECTION: Umm....I think I just screwed up....I have the '08 LB, so I had to connect a blue wire from the ECM to the connection behind the steering wheel, right?
Yes, with an 08, you have to add the wire from the cruise control switch connector CCS pin at the output of the spiral cable to pin 40 of connector A21 of the ECM (at the location of the blue wire on the connector below, which has three wires). You will also have to add a ground connection at the location of the brown wire on that same connector. On your 08 you will only have one wire (the black horn wire) exiting that connector.

texkidSugar Land, TX · Jul 30, 2009#414 Originally Posted by
CTScott ↑ Yes, with an 08, you have to add the wire from the cruise control switch connector CCS pin at the output of the spiral cable to pin 40 of connector A21 of the ECM (at the location of the blue wire on the connector below, which has three wires). You will also have to add a ground connection at the location of the brown wire on that same connector. On your 08 you will only have one wire (the black horn wire) exiting that connector.
Woo-hoo! Got it working. There is no indicator on the cluster but I believe that is to expected. I don't think I can do the DIY since the memory card got corrupted. I am still doing some data recovery on the card but I ain't holding my breath.
texkidSugar Land, TX · Jul 30, 2009#415Okay, nothing good coming out of my old memory card. So...I took some quick pics and some other images from the other camera. I am not going to take everything apart again, its too darn-tootin' hot!
Picture lost · texanurse.com
Picture lost · texanurse.com
Picture lost · texanurse.com
Picture lost · texanurse.com
I did actually had a good idea for the garbage disposal splash guard. I planned to use it to over up the empty space around the cruise control switch to give it an "OEM" look. But since I made a pretty BAD cut, that idea went out the window. But, if y'all learn from my mistake, this might end up be a decent idea.
Picture lost · texanurse.com
CTScottUSA, CT · Jul 31, 2009#416Ouch on that cut around the stalk. Isn't there a molded cut line in the plastic that you could have followed?
texkidSugar Land, TX · Jul 31, 2009#417 Originally Posted by
CTScott ↑ Ouch on that cut around the stalk. Isn't there a molded cut line in the plastic that you could have followed?
Kind of. But it was too late because I didn't see it until I connected the wires to the stalk. It is supposed to rain this weekend, so hopefully things will cool off. If it does, then i'll the airbag off and take a picture.
CTScottUSA, CT · Jul 31, 2009#418 Originally Posted by
texkid ↑ Kind of. But it was too late because I didn't see it until I connected the wires to the stalk. It is supposed to rain this weekend, so hopefully things will cool off. If it does, then i'll the airbag off and take a picture.
If you decide to replace the cover, the part number is:
Cover, Steering Wheel Boss, Lower: 45184-52130-B0
This part number is supposedly for the one with the cruise control hole already there.
texkidSugar Land, TX · Jul 31, 2009#419 Originally Posted by
CTScott ↑ If you decide to replace the cover, the part number is:
Cover, Steering Wheel Boss, Lower: 45184-52130-B0
This part number is supposedly for the one with the cruise control hole already there.
I had thought buying the wheel cover but decided to hold until I bought the shifter extender which is next on the list. I will eventually get that wheel cover though.
BrianSSeattle, WA · Jul 31, 2009#420Odd question here. I actually had the aftermarket Rostra cc put in. I prefer the OEM look tho. If I wanted to get the OEM stalk and install that instead, would I have to start from scratch, running all those wires or could I utilize the wiring the Rostra has coming to it somehow?
CTScottUSA, CT · Jul 31, 2009#421 Originally Posted by
BrianS ↑ Odd question here. I actually had the aftermarket Rostra cc put in. I prefer the OEM look tho. If I wanted to get the OEM stalk and install that instead, would I have to start from scratch, running all those wires or could I utilize the wiring the Rostra has coming to it somehow?
I looked at the Rostra installation instructions and it actually connects to the ECM via the accelerator position sensor input. It has inputs to its own module from the brake pedal and gas pedal as well. Basically, it does the cruise control thing the way it would be done on a car who's ECM doesn't do it, so the bottom line is that none of the Rostra wiring would be of any value, if you switched to the OEM method.
BrianSSeattle, WA · Jul 31, 2009#422 Originally Posted by
CTScott ↑ I looked at the Rostra installation instructions and it actually connects to the ECM via the accelerator position sensor input. It has inputs to its own module from the brake pedal and gas pedal as well. Basically, it does the cruise control thing the way it would be done on a car who's ECM doesn't do it, so the bottom line is that none of the Rostra wiring would be of any value, if you switched to the OEM method.
Ah darn! LOL! I was trying to avoid tearing my dash apart. Thanks for the reply tho CTScott. :)
SoylentglassN.E. · Aug 4, 2009#423 Originally Posted by
CTScott ↑ I finally found the info on the correct terminal with the waterproof sleeve for the ECM connection. It is the female terminal with the waterproof sleeve and 500mm of wire attached. It is intended to be a repair item for a damaged terminal, where the tech just has to splice the wire, rather than having to deal with attaching the wire properly to the terminal.
The part number is: 82998-24250
Hi All. I have been lurking, reading through the 2 posts about the DIY cruise control on and off for a while now. I have an 09 Yaris Sedan, M/T. I took off the panels on the top and bottom of the steering column and have verified that yes, my car also does not have the brown and the blue wires coming from the plug. Only the black ground for the horn. It does have the indicator lights on the dash to the right of the speedometer. The "CC on" light and the "set" light.
I have been looking over the 2007 yaris factory repair manuals. I have been following along with everything you said and it all looks good to me.
CTScott, I had a few questions for you that I couldn't find the answer for anywhere in any of the close to 40 pages of both the posts.
First, where are you finding the OEM part numbers? Like for the interior panels for instance. I found a lot of part numbers for connectors at the end of the wiring diagrams section of the factory manual, but could not find a toyota OEM parts diagram anywhere.
Second, I was thinking of trying to get this ECM connection with the wire already attached that I have quoted above from you. Then I was thinking about it and from what you have, I wasn't sure if this was somehow a terminal that plugged into pin 40 on connector A21 or if this part was the entire A21 connector with about 40 or 50 - 500mm lengths of wire coming from all the pins. If it were the latter, I wouldn't want to get it, because I am not about to cut and splice all the rest of the existing, in-place, wires just so I could get that one wire from pin 40 waterproofed. So I guess the question summed up is: is part number 82998-24250 one wire with a connector or A21 with a lot of wires coming out of it?
The wiring diagram manual has part number 90980–12462 for A21 and TRD sparks has a higher MSRP for this than they do for part number 82998-24250.
Also, I looked up under the dash today and found a white two prong plug, with a blue and a black wire going to it. This plug was taped up against the wiring harness and was not plugged in to anything. It looks to me like its the right plug for the Cruise Control Clutch Switch according the the wiring manual.
I am planning on doing the 2 switch method, but I have yet to buy any of the switches, resistors, Cruise Control Clutch Switch, or the waterproof connector for the ECM.
Another thing I was wondering, if I wouldn't have access to what you are using to get OEM part numbers. On the sedan, there is a small panel to the right of the dimmer switch. I want to put my switches there. Is there any way you could find out what the part number is for that panel, so I could try to order another one?
Full of questions here. If I go to the dealer with these part numbers, will they just be able to order them for me? Or should I try to go through TRDSparks or somewhere online? It seems like, at least for the older toyotas I've had, that the dealer cannot get a lot of items like interior panels and the like. This is my first new car, so maybe it's different, I'm not sure. I was trying to avoid paying shipping costs, they seem a little high at TRDsparks and I always hate waiting heh. But I do get annoyed when they ask for a VIN number at the dealer too.
Overall, I'd like to say thanks to everyone who contributed to these posts. I was planning on buying that aftermarket kit (which I originally thought was the OEM CC) from TRDSparks for like $200 before I found this.
CTScottUSA, CT · Aug 4, 2009#424 Originally Posted by
Soylentglass ↑ Hi All. I have been lurking, reading through the 2 posts about the DIY cruise control on and off for a while now. I have an 09 Yaris Sedan, M/T. I took off the panels on the top and bottom of the steering column and have verified that yes, my car also does not have the brown and the blue wires coming from the plug. Only the black ground for the horn. It does have the indicator lights on the dash to the right of the speedometer. The "CC on" light and the "set" light.
I have been looking over the 2007 yaris factory repair manuals. I have been following along with everything you said and it all looks good to me.
CTScott, I had a few questions for you that I couldn't find the answer for anywhere in any of the close to 40 pages of both the posts.
First, where are you finding the OEM part numbers? Like for the interior panels for instance. I found a lot of part numbers for connectors at the end of the wiring diagrams section of the factory manual, but could not find a toyota OEM parts diagram anywhere.
Second, I was thinking of trying to get this ECM connection with the wire already attached that I have quoted above from you. Then I was thinking about it and from what you have, I wasn't sure if this was somehow a terminal that plugged into pin 40 on connector A21 or if this part was the entire A21 connector with about 40 or 50 - 500mm lengths of wire coming from all the pins. If it were the latter, I wouldn't want to get it, because I am not about to cut and splice all the rest of the existing, in-place, wires just so I could get that one wire from pin 40 waterproofed. So I guess the question summed up is: is part number 82998-24250 one wire with a connector or A21 with a lot of wires coming out of it?
The wiring diagram manual has part number 90980–12462 for A21 and TRD sparks has a higher MSRP for this than they do for part number 82998-24250.
Also, I looked up under the dash today and found a white two prong plug, with a blue and a black wire going to it. This plug was taped up against the wiring harness and was not plugged in to anything. It looks to me like its the right plug for the Cruise Control Clutch Switch according the the wiring manual.
I am planning on doing the 2 switch method, but I have yet to buy any of the switches, resistors, Cruise Control Clutch Switch, or the waterproof connector for the ECM.
Another thing I was wondering, if I wouldn't have access to what you are using to get OEM part numbers. On the sedan, there is a small panel to the right of the dimmer switch. I want to put my switches there. Is there any way you could find out what the part number is for that panel, so I could try to order another one?
Full of questions here. If I go to the dealer with these part numbers, will they just be able to order them for me? Or should I try to go through TRDSparks or somewhere online? It seems like, at least for the older toyotas I've had, that the dealer cannot get a lot of items like interior panels and the like. This is my first new car, so maybe it's different, I'm not sure. I was trying to avoid paying shipping costs, they seem a little high at TRDsparks and I always hate waiting heh. But I do get annoyed when they ask for a VIN number at the dealer too.
Overall, I'd like to say thanks to everyone who contributed to these posts. I was planning on buying that aftermarket kit (which I originally thought was the OEM CC) from TRDSparks for like $200 before I found this.
The service manuals don't list part numbers. The part numbers come from the Toyota EPC (electronic parts catalog). You can access it online at Toyodiy.com
82998-24250 is a single wire with the terminal and waterproof plug for connecting to the ECM.
If the cover you are looking for the PN for is the one where the power mirror switch would be then the PN is: 55547-28010-B1
For ordering the parts, you are probably better off going through TRDsparks. The dealer prices will be higher, and they will probably have to order most of the parts, so you may not save any time.
2+2Michigan · Aug 16, 2009#425 Originally Posted by
CTScott ↑ If you decide to replace the cover, the part number is:
Cover, Steering Wheel Boss, Lower: 45184-52130-B0
This part number is supposedly for the one with the cruise control hole already there.
Just to confirm. Yup, that's the correct part number. I just received it yesterday and I'll be installing it as soon as the stalk arrives from Thailand. 16 days and counting since I placed the order. 🙄
For future cruise control installers: the part has the factory perfect hole already cut out for the cruise control stalk. The price from Sparks was $21.82 plus shipping. I also ordered the clutch switch (88280-14030) for $14.86 from them.
2+2Michigan · Aug 17, 2009#426I got my stalk from Thailand today and installed it in my 09 3dr MT.
The clutch switch: Maybe no one mentioned it because it's so obvious but at least on the 09s there's a piece of black plastic under the dash that blocks the view of where the clutch switch goes. There's only 2 screws that hold it in place and once you remove it you can see where the switch goes without learning yoga. I wish I had paid more attention to how far the original clutch pedal adjustment bolt was before I installed the switch so I'd be sure I adjusted it correctly. My first thought was to screw it in until the clutch pedal began to move and then stop. But the pedal didn't feel quite right at the top of it's travel so I gave the switch a couple more turns. Is that right? Doesn't matter with a hydraulic clutch does it?
The steering wheel and stalk: Everything went really well thanks to all the good pointers here 👍 But of course box-o-rocks me had to try and make it interesting. I ordered the wrong stalk. Mine didn't have the horn wire hanging off the connector like
Picture lost · texanurse.com
I ended up reusing my original horn wire by freeing the wire and connector from the plug and plugging it into the connector on the end of my stalk.
Thanks to everyone that worked on this I've now got cruise control and it didn't cost an arm and a leg and it was fun to do. 🙇
Should I worry about my clutch pedal adjustment?
luigiAugusta, GA · Aug 18, 2009#427Thanks to all the pioneers in this thread, I installed my cruise two weekends ago. I opted to buy the toyota stalk and steering wheel cover. Parts cost: $65 (including wire)
Installation was a breeze in my Auto Yaris. I bought 16 gauge wire, which was a tad too large for all the connectors and such. Still, after a little "love", everything is working and looks great. It looks like it came from the factory with cruise! Everyone is impressed, even the wife. Victory is mine!
My suggestions:
1. Go 18-22 gauge for the wire.
2. Don't spend $30 on the toyota steering cover. Put that money toward a dremel tool which you can use for a thousand other things. Plus, now I have a cover with no hole just taking up valuable garage space.
3. Have zip ties ready ahead of time. (Doh!)
4. My stalk, bought off eBay, didn't have any screws with it. Luckily, I found one lying around that sorta worked. You'll need two; have these around pre-project, too.
5. Take your foot off the gas on the interstate and LOVE IT!👍
Vince87Montreal, Qc, Canada · Aug 18, 2009#428Hey Guys ! I ordered the Clutch Switch from a Toyota dealer (33CAD$) and I have a quick question for those who installed it on their Yaris : Is there's a way to avoid having to get a wire from that switch to the engine bay (is the blue CC wire going anywhere in the dash) ?
If my understanding is correct, I have to run a wire from the switch to the CC wire (blue) in the engine bay fuse box, and ground the other wire from the switch. I think I read that someone had slice the wire going to the fuse box to connect it to the wire going to Pin40 of connector A21 and I dont understand why this would have to be done since the blue wire only has to be grounded when the clutch pedal is depressed.
PS. to all those who did the installation on a MT car without the clutch switch, BUY IT ASAP ! I barely blown my engine after riding for 3.5 hours when I put my car in neutral (yeah I know that was dumb, I was tired).
Thanks for your help!
CTScottUSA, CT · Aug 18, 2009#429 Originally Posted by
Vince87 ↑ Hey Guys ! I ordered the Clutch Switch from a Toyota dealer (33CAD$) and I have a quick question for those who installed it on their Yaris : Is there's a way to avoid having to get a wire from that switch to the engine bay (is the blue CC wire going anywhere in the dash) ?
If my understanding is correct, I have to run a wire from the switch to the CC wire (blue) in the engine bay fuse box, and ground the other wire from the switch. I think I read that someone had slice the wire going to the fuse box to connect it to the wire going to Pin40 of connector A21 and I dont understand why this would have to be done since the blue wire only has to be grounded when the clutch pedal is depressed.
PS. to all those who did the installation on a MT car without the clutch switch, BUY IT ASAP ! I barely blown my engine after riding for 3.5 hours when I put my car in neutral (yeah I know that was dumb, I was tired).
Thanks for your help!
The clutch switch is totally separate from the CC wire to the ECM. The ECM has an input "D" (Connector C20 - Pin 56 on the ECM) for the cruise control clutch switch. It routes through the under hood fuse panel, so you can tap it there, rather than going to the ECM.
The 09 LBs have the clutch switch connector, but prior years and the Sedan apparently do not. From the clutch switch, two wires go up to the fuse panel and connect to the blue and white wires shown in the following picture. Neither gets grounded.
Picture lost · i236.photobucket.com Vince87Montreal, Qc, Canada · Aug 18, 2009#430Thanks CTScott ! you always have the answer faster than anybody else... is there's a more straightfoward route to the fuse box than the grommet under the carpet on the passenger side (thats were the Pin40 and my amp wires a going to the engine bay) ?
ps. I thought that the white wire was a ground, thats why I believed I could ground it on the chassis instead...
CTScottUSA, CT · Aug 18, 2009#431 Originally Posted by
Vince87 ↑ Thanks CTScott ! you always have the answer faster than anybody else... is there's a more straightfoward route to the fuse box than the grommet under the carpet on the passenger side (thats were the Pin40 and my amp wires a going to the engine bay) ?
ps. I thought that the white wire was a ground, thats why I believed I could ground it on the chassis instead...
You can go through the driver's side grommet, which goes in up behind the inside fuse panel and comes out just behind the battery.
White with a black stripe is always ground on the Yaris. Solid white is often 12 V power (which is the case with the wiring for the clutch switch).
Vince87Montreal, Qc, Canada · Aug 18, 2009#432Nice thanks ! I didnt wanna have a wire hanging loose from one side of the engine bay to the other...
ps for those who waited for a clear DIY with pictures for the 07-08 LB (with or without MT) I will built one this week !
texkidSugar Land, TX · Aug 25, 2009#433Well....just made a huge correction on my clutch switch wiring. I was driving home and I tapped the clutch to coast to a stop when all of the sudden the car started roaring like the heavens. I assessed the situation and found that the connections at the clutch switch came loose and were touching each other, essentially the power was still running through when the clutch was pressed. I went back to the hardware store and bought some smaller, tighter "connections" and now everything is working fine. So, the moral of the story, double check all your connections before testing/sealing it up or else you'll spend an extra hour in the HOT garage fixing it the right way.
fraenxGlendale · Aug 26, 2009#434Hi, I just read through all 29 pages in this post and as previously mentioned in some other posts am a little confused with all the segregated information. Has anyone created a detailed DYI yet including pictures to add the OEM cruise control stalk on a 2007 hatchback?
goku87AK · Aug 27, 2009#435 Originally Posted by
fraenx ↑ Hi, I just read through all 29 pages in this post and as previously mentioned in some other posts am a little confused with all the segregated information. Has anyone created a detailed DYI yet including pictures to add the OEM cruise control stalk on a 2007 hatchback?
+1 its all pretty confusing.
CtrlAltDefeatIndianapolis IN · Aug 27, 2009#436me too I'd really like one before I take apart my dashboard...
BrianSSeattle, WA · Aug 30, 2009#437Someone posted a step-by-step for adding CC without the stalk. This one does cover all the wiring we (pre-2009'ers) have to do from the various connectors to the ECM and such. Now we just need a section on adding the factory stalk into it. :)
DIY Cruise Control on 07-08 Yaris (step by step) SoylentglassN.E. · Sep 13, 2009#438Well, after some trial and error, I finally have my cruise control installed and working on my manual 09 Sedan. With working factory installed dash lights and all.
First off, I had a major error which made a lot more work for myself. I did the same thing nickhjort did a lot earlier in this thread. It had been awhile since I read through everything. I should have reread it all and it would have saved me, but oh well. I was looking at the pictures of the ECM terminals in the factory repair manual and was thinking it was plug A21 when I went to put in terminal 40. So I was looking at a mirror image and ended up putting the repair terminal (part#82998-24250, still don't know where CTScott found this part number but it worked) into terminal 29 like nickhjort originally did. It also helps to know that the terminal will not go into the hole, unless you push the locking mechanism, a white piece of plastic in the middle of the plug. Next, I used a small piece of metal rod and taped the ECM wire to it and threaded it through the grommet above the brake pedal and was able to pull it through from behind the battery in the engine compartment. I unbolted the battery and moved it forward so I could get behind it a little better. I grounded the switches (I did the 2 switch method) on the bolt close to the floor behind the drivers side kick panel. I mounted the same switches CTScott used from digikey on an extra mirror control panel I bought. By the way the color of that panel on my car (I have "bisque" interior) is called "greige" (grey and beige mixed together apparently) on the 2007 toyota EPC (since they didn't have 2008 or 2009 yet on toyodiy.com). Also, from digikey, I used a 390 ohm resistor and a 240 ohm resistor in series.
It didnt work at all when I first used it since I put that repair terminal in 29 of connector A21. Which I figured out pretty quickly(when I took a better look at the connector I realized that the terminal numbers were molded into the connector, I think at the corner terminals), but I then realized that I already had a blue wire coming from terminal 40. But I do not have the brown and blue wires going to connector D3 in the steering column, just the black wire. Since I really did not feel like trying to get at connector AD4 WAY up in the dash on the drivers side, I ended up just cutting the wire I had sent to terminal 29 and also cutting the factory terminal 40 wire and putting them together. So I bought that repair terminal ($11.19) for no reason.
Since the wire from the ECM terminal 40 to connector AD4 already existed, maybe the ground wire exists somewhere in my car somewhere, maybe all the way to junction connector D34, but I didn't bother looking since I had already grounded to a bolt, which was easy. D34 seems to be all the way up in the passenger side dash, so I didn't even bother looking.
I also wanted to say that my 09 Sedan does have the factory connector for the cruise control clutch switch, so I able to just plug it right in. Speaking of that, the reason why it took me so long to get this installed from my original post is because it took TRDSparks 2 weeks to send out my parts. Then it took another 4 business days to ship. $10 for shipping was a little steep for about half a pound of freight too. I also should have waived having to sign for the package since I work during the day and it was a pain getting the package from UPS. I wasn't totally positive at first where to mount the switch either. I know the repair manual shows it as normally closed, but I couldnt tell by looking at the switch itself what position it was in with the button in or out and didn't feel like getting the multimeter to test it, heh so I just threw it in the place of the original clutch adjustment screw, which apparently is the correct place.
As far as the actual operation of the cruise control, I like how you can accelerate past what you set the cruise control at and if you let off the gas, once it coasts back to the speed you set it at, it will remain going that speed.
Once again, thanks again to all for paving the way on this install. I hope some of my trials and tribulations may help someone else and save them some of the rework that I had to do.
pinnerhillMontpelier, Virginia · Sep 15, 2009#439Hey Guys (and maybe some gals), thank you for all the info you provide to this site. It is definitely more fun to DIY. First, I have an 09 yaris sedan AT bare bones. Question, I have read through this forum many times over and all that is said about the above car for cruise control is to get the stalk and wire harness, then install. The ECM is preprogrammed to handle the addition of the stalk. Take the ground wire and add it to the wire harness. Put everything back together. Bam! you have cruise control. No running wires and no further switches or resisters. Well I got nothing.
I got my stalk from Thailand (ebay) and now wondering if I should have waited the month to get it. I have followed the directions of removing airbag, cutting hole, install stalk with 10-32 1/2in screws, plug in wire harness, remove ground pin from original plug and insert into new plug. Put everything back together. From my understanding, this is the easiest dyi for cruise considering the time to cost ratio.
Dead in the water with my nice new stalk looking at me laughing. I am wondering if I have a bad stalk or did I miss something in the 30 pages from this site or the countless other Q's and A's over the web. Please advise of where one might go from here. I will try hooking up an multimeter this evening to see if I get any response from the switch. I am pretty handy at most things, however electricity is not my thing. Thanks in advance for any help.
Betriventedmonton · Sep 15, 2009#440I've been thinking of getting a small 2W Solar Panel for my car. Would there be any benefits at all if I left it continuously plugged in through my cig lighter jack? And a 2W can't possibly overcharge my battery can it?
AlexNet0Rockland, ME · Sep 15, 2009#441 Originally Posted by
Betrivent ↑ I've been thinking of getting a small 2W Solar Panel for my car. Would there be any benefits at all if I left it continuously plugged in through my cig lighter jack? And a 2W can't possibly overcharge my battery can it?
not relevant to this thread, but to answer you, plugging it in all the time when your car is not turned on will do nothing. the outlet is switched to only be powered when accessory circuit is activated.
Betriventedmonton · Sep 15, 2009#442Sorry, didn't realise I couldn't ask that here, I thought this thread was for general inquiries. According to the product description I can charge the battery through the outlet, or directly to the battery via clamps.
EDIT: I'm an idiot, didn't realise this was strictly for Cruise Control. My bad!
CTScottUSA, CT · Sep 15, 2009#443 Originally Posted by
pinnerhill ↑ Hey Guys (and maybe some gals), thank you for all the info you provide to this site. It is definitely more fun to DIY. First, I have an 09 yaris sedan AT bare bones. Question, I have read through this forum many times over and all that is said about the above car for cruise control is to get the stalk and wire harness, then install. The ECM is preprogrammed to handle the addition of the stalk. Take the ground wire and add it to the wire harness. Put everything back together. Bam! you have cruise control. No running wires and no further switches or resisters. Well I got nothing.
I got my stalk from Thailand (ebay) and now wondering if I should have waited the month to get it. I have followed the directions of removing airbag, cutting hole, install stalk with 10-32 1/2in screws, plug in wire harness, remove ground pin from original plug and insert into new plug. Put everything back together. From my understanding, this is the easiest dyi for cruise considering the time to cost ratio.
Dead in the water with my nice new stalk looking at me laughing. I am wondering if I have a bad stalk or did I miss something in the 30 pages from this site or the countless other Q's and A's over the web. Please advise of where one might go from here. I will try hooking up an multimeter this evening to see if I get any response from the switch. I am pretty handy at most things, however electricity is not my thing. Thanks in advance for any help.
If you look at Soylentglass's post above you'll see that you need to add the wire from pin 40 of connector A21 of the ECM to the spiral cable connector on the steering column. For whatever reason, the 09 sedans (or at least some of them) don't have the wire from the ECM, like the liftbacks do.
SoylentglassN.E. · Sep 16, 2009#444Actually, my car had a wire factory installed into pin 40 of connector A21. I just had the plug upside at first and was looking at pin 29, which was empty. But the blue wire from pin 40 only went to connector AD4 and stopped, there was no wiring from AD4 to the steering column.
Pinnerhill, if your car is like mine (yours is an auto and mine is a manual, but both 09 sedans) then you might have to tap off of the blue wire coming from pin 40 in the engine bay and run it to the stalk. So far, it seems that only the 09 Liftbacks (which a lot of people seem to own who have responded on this post) have all the wiring factory installed. I'm not sure what you mean by "remove ground pin from original plug and insert into new plug", but there should be two wires going to the stalk either way, one from the ECM and one from ground (bolt). I installed my own switches and did not obtain a stalk. From CTScotts DIY for 2009 liftbacks
DIY - 2009 Cruise Control for $10, without pulling the steering wheel and airbag , the wires going to the connector (D3) in the steering column should be brown (going to terminal 2 of connector D3) and blue (going to terminal 1 of connector D3)
pinnerhillMontpelier, Virginia · Sep 18, 2009#445Thanks for the all the advice. Wanted to clarify about the ground wire first from my previous post. This is the wire that connects the air bag or horn ground to the clock spring plug. My wire harness was already setup to plug in the same spot, so I removed the pin the ground wire used from the old plug and inserted it into the new wire harness plug. I believe it has nothing to do with the CC stalk.
I checked last night and I do not have any of the cruise control wires going to the D3 on the steering column. So I guess my next question is do I attempt to splice in at the A21 pin 40 and go through the firewall somewhere (this will suck) or try a back-breaking position (suck even worse) and splice off the AD4 which I believe is up there on top of the fuse box and you really cannot see it from under the dash? I understand now the second wire just needs to go to ground near the driver side door, correct?
Last question (for now at least because ya'll are awesome), what is the best way to splice and protect from moister and vibration?
Thanks a lot to CTScott, Soylentglass and countless others for taking the time to post and help the not so savvy DIY'ers.
CTScottUSA, CT · Sep 18, 2009#446For the connection to the pin 40 wire, you are probably better off hitting it near the ECM and then coming through the grommet just above the ECM. Splice with a tap, or strip and solder, and then wrap with good (3M) electrical tape to seal.
To do the AD4 connection, you'd really need to remove the top of the dash. It's too far to reach from under.
For the ground connection, you can go down to the driver's kick panel, or you can ground to the metal support structure for the dash (there are a few bolts that you can get a terminal under).
SoylentglassN.E. · Sep 18, 2009#447I agree with CTScott. I'd also say that tapping into the wire in the engine bay near the ECM would be the best choice. That is what I ended up doing once I realized that there was already a wire coming from pin 40. I went through the grommet behind the battery, but it was kind of a pain. From all the other posts it seems like the grommet above the ECM is a better choice. I taped the wire to a small metal rod [anything rigid (a coat hanger?) would work too] to thread the wire through the grommet on the side of the wiring harness. REALLY tape it good though, the wire came off the first time on me and I wasn't too happy to have to do it again. Also putting extra tape will reduce the chance of any sharp edges cutting the grommet or wire harness.
I could not see connector AD4 from the driver's side floor no matter how I contorted myself. I couldn't see it, never mind attempt to jam my arm up there to get at it. My back hurt a bit the next day since I was laying in that position with the kickboard in my back for about half an hour.
AlexNet0Rockland, ME · Sep 18, 2009#448 Originally Posted by
CTScott ↑ For the connection to the pin 40 wire, you are probably better off hitting it near the ECM and then coming through the grommet just above the ECM. Splice with a tap, or strip and solder, and then wrap with good (3M) electrical tape to seal.
To do the AD4 connection, you'd really need to remove the top of the dash. It's too far to reach from under.
For the ground connection, you can go down to the driver's kick panel, or you can ground to the metal support structure for the dash (there are a few bolts that you can get a terminal under).
maybe I am just very slow, but I cannot find how to remove the top dash.
CTScottUSA, CT · Sep 18, 2009#449 Originally Posted by
AlexNet0 ↑ maybe I am just very slow, but I cannot find how to remove the top dash.
Check out the AC section of the service manual. Page 113 shows the screws you have to remove.
AlexNet0Rockland, ME · Sep 18, 2009#450here it is for those who dont have the manuals.