Well it would depend on schedules meshing for sure. Oneida is 3.5-4 hour drive.
Can we do this? (aka The DIY Cruise Control Thread)
498 posts · 380,332 views · page 8 of 10
Replies continued
Well I'm always free on weekends, so let me know what you think 👍
any sunday
So I have an 08 LB 5mt. What will I need to make the cruise work. I want to go the homemade switch version. Do I need a certain voltage switch? The radio shack across the street has illuminated switches for 2.99 each. What resistors.
So I have to run a wire from the # 40 pin on the ecm to said switches correct? What about grounding etc.
I really want to have cruise this weekend. I have to start commuting 105 miles each way for work.
So I have to run a wire from the # 40 pin on the ecm to said switches correct? What about grounding etc.
I really want to have cruise this weekend. I have to start commuting 105 miles each way for work.
Brave I have an '08 LB MT too I would go the stalk method...you really need to know WTF you are doing to go the switch route, and there will be a lot of work involved. CTScott makes it sound easier than it is I'm sure, I run the electric grid for a living and am JUST following along with his LED and resistors method.
Im going the stalk switch route, however doing the wiring myself, like nickhjort, just need to find the time
when I finally get around to doing it, I will make one, however it will be the stalk method, since I like more of an oem look.Originally Posted by CTScott ↑Correct. We really need to do a DIY for 07-08's...
If you use illuminated switches, you will need to power the lights from a separate isolated circuit (such as the interior illumination circuit).Originally Posted by Bravejus ↑So I have an 08 LB 5mt. What will I need to make the cruise work. I want to go the homemade switch version. Do I need a certain voltage switch? The radio shack across the street has illuminated switches for 2.99 each. What resistors.
So I have to run a wire from the # 40 pin on the ecm to said switches correct? What about grounding etc.
I really want to have cruise this weekend. I have to start commuting 105 miles each way for work.
Take a look at my DIY Cruise Control Thread for the switch and resistor info:
DIY - 2009 Cruise Control for $10, without pulling the steering wheel and airbag
Basically, any normally open, momentary switch will be fine. The switches are switching 12VDC at negligible current.
For an 07-08:
In the Steps mentioning Connector D3, the blue (CCS) and brown (ECC) wires are replaced with a wire from the red wire of the switches to CCS on the ECM (pin #40) and a wire from the black wire of the switches to a ground point (a bolt connecting a ring terminal to the bare metal of the dash support structure for example).
For MT on 07-08:
The clutch switch (Toyota part number: 88280-14030) is required. A wire is run from each of the two terminals of the switch to the terminals of the under hood fuse panel connector shown in nickhjort's picture below (either switch terminal to either connector terminal is fine).
http://i236.photobucket.com/albums/f...t/CIMG6560.jpg
The 07-08 will not have a cruise control on indicator unless something like the module I developed is used. You can not simply use an illuminated switch, as the on/off switch is a momentary switch, which toggles the function on or off.
Thanks CTScott that helps. So essentially I am running a wire from # 40 on ecm to the Positive on the switch setup. then ground out the switches.
There was a way to jump the clutch switch to see if the cruise works though correct? Also on the topic of clutch switch, I have to run wires from the switch to the pictured panel connector? Do I need as large of a wire with a fuse or would a regular wire work?
There was a way to jump the clutch switch to see if the cruise works though correct? Also on the topic of clutch switch, I have to run wires from the switch to the pictured panel connector? Do I need as large of a wire with a fuse or would a regular wire work?
Nevermind about the clutch switch figured it out, for the jumper.
But for running the wires for the stock switch you would connect to the blue wire for the positive then just run a ground correct?
But for running the wires for the stock switch you would connect to the blue wire for the positive then just run a ground correct?
Correct.Originally Posted by Bravejus ↑Nevermind about the clutch switch figured it out, for the jumper.
But for running the wires for the stock switch you would connect to the blue wire for the positive then just run a ground correct?
If you do the clutch switch bypass for testing, just make absolutely sure you don't press the clutch pedal while in cruise mode.
And I have cruise. Took me about three hours to do. But this was my first wiring/soldering experience. However my father has done a lot of it so he showed me how to solder. The hardest part was running the wires through the firewall.
Now just waiting on the clutch switch so it will be safer.
Thanks so much CTScott, nickhjort, and PK198105 for figuring all this out for us Yaris owners.
I was literally thinking of trading mine in for a newer more loaded one because i had no cruise. But now i don't need to.
Now I need to figure out if I can make a remote hatch release cause that is annoying.
Now just waiting on the clutch switch so it will be safer.
Thanks so much CTScott, nickhjort, and PK198105 for figuring all this out for us Yaris owners.
I was literally thinking of trading mine in for a newer more loaded one because i had no cruise. But now i don't need to.
Now I need to figure out if I can make a remote hatch release cause that is annoying.
Before I buy a stalk from a stranger on eBay, I thought I'd try to buy from a stranger on YW. 😁 Is anyone still trying to get rid of their cruise stalk?
So, I've poured through 80% of these pages. I have an 09 Sedan, automatic, base model. No power windows or locks. No cruise either.
I would be looking to add a stalk for the cruise, from what I've gathered all I should have to do is get the stalk and hook it up? Does anyone have pictures of adding a stalk to an 09 automatic?
I would be looking to add a stalk for the cruise, from what I've gathered all I should have to do is get the stalk and hook it up? Does anyone have pictures of adding a stalk to an 09 automatic?
All you have to do on the '09 is add the stalk as the ECU is already wired for cruise. All that is required for the oem cruise is to buy the trim piece for your steering column that has the stalk hole and buy the stalk. then remove the steering column cover, plug in the stalk, and put the new cover on. If you don't want to foot the bill for new pieces, you can remove the cover and splice in switches to the factory wires as shown earlier in the this thread and in the diy.Originally Posted by ecnal ↑So, I've poured through 80% of these pages. I have an 09 Sedan, automatic, base model. No power windows or locks. No cruise either.
I would be looking to add a stalk for the cruise, from what I've gathered all I should have to do is get the stalk and hook it up? Does anyone have pictures of adding a stalk to an 09 automatic?
Well, I'm guessing that a column cover wouldn't run all that much. Plus about 30 total for a stalk assuming you buy one on ebay and not find one at a yard somewhere. Outweighs the cost of having it installed at the dealer! Plus it probably adds a little bit of resale value to it.
Did this work for any of you?
Yes. I installed it using my $10 switch method on my 09. Quite a few have now done it on 07's through 09's.Originally Posted by FunkyCole ↑Did this work for any of you?
DIY - 2009 Cruise Control for $10, without pulling the steering wheel and airbag
Originally Posted by PatrickJohnson ↑All that is required for the oem cruise is to buy the trim piece for your steering column that has the stalk hole
I dont know about the 08's or 09's, but on my 07 the steering column cover already had a notched spot so you could easily cut out the hole for the stalk.
Good read!
Any updates on an 09 yaris MT? Any confirmations regarding the connector for the clutch switch?
Parts needed:
Clutch Switch: 88280-14030
Steering Cover: 4518452130b0
Stalk: 84632-34011
I already ordered the stalk on ebay for $29.99 shipped.
-Brent
Any updates on an 09 yaris MT? Any confirmations regarding the connector for the clutch switch?
Parts needed:
Clutch Switch: 88280-14030
Steering Cover: 4518452130b0
Stalk: 84632-34011
I already ordered the stalk on ebay for $29.99 shipped.
-Brent
Did any of you guys find out if this works?
I've seen here a question about the European Multimode (robotic transmission),
This guy had a 2007 model; I own the new 2009 face lifted (+new engine, new transmission) 2009 model NSP90L – CHLGKW, does anyone knows if its ECM supports Cruise Control?
10x
This guy had a 2007 model; I own the new 2009 face lifted (+new engine, new transmission) 2009 model NSP90L – CHLGKW, does anyone knows if its ECM supports Cruise Control?
10x
I believe that none of the European Yaris support it. I have the European EWD's, and cruise is not documented. From what I've seen browsing the European Toyota sites, it doesn't look like cruise is a factory option, just an expensive aftermarket option.Originally Posted by manta ↑I've seen here a question about the European Multimode (robotic transmission),
This guy had a 2007 model; I own the new 2009 face lifted (+new engine, new transmission) 2009 model NSP90L – CHLGKW, does anyone knows if its ECM supports Cruise Control?
10x
Out of curiosity, have you checked to see if your Yaris has the the cruise indicators somewhere near the speedometer (you can shine a bright flashlight to make it visible)?
First of all I'd like to thank everyone who's been putting so much work into this, A+ job guys!
I'm looking to do this on my '07 AT hatchback, can't find a stalk on ebay so if anyone has one laying around PM me and I'll buy it off ya
after I get that accomplished I may hit you up CTScott about one of those LED array thingys... then I can prolly throw together a DIY for the 07-08 AT crowd once I get the parts :D
I'm looking to do this on my '07 AT hatchback, can't find a stalk on ebay so if anyone has one laying around PM me and I'll buy it off ya
after I get that accomplished I may hit you up CTScott about one of those LED array thingys... then I can prolly throw together a DIY for the 07-08 AT crowd once I get the parts :D
Hi guys ! first of all I want a thanks everyone who contributed in making this amazing mod available for everyone, especially CTScott and . I found this community while I was looking for a DIY CC installation for my Yaris, and I never thought I would be able to make it for less than 10$, thats just the coolest mod ever ! I followed very carefully your instruction and still can't make it work... Here's a few pics of my installation :
The switches

Connector D3 without CC wires

Red wire from switch to pin 40 of connector A21

Gray ground wire in the back grounded in the door sill

Jumper from clutch switch cable to ground

At first I thought that my ground was bad so I changed from a bolt behind the passenger glove box to that one with no success... I also changed the jumper wire to a bigger one. I still believe that the problem is the ground, I have a multimeter and knows how to check if a ground is really a ground but not if it is a good one. If any of you can explain it to me it would be very appreciated ! Thanks
The switches

Connector D3 without CC wires

Red wire from switch to pin 40 of connector A21

Gray ground wire in the back grounded in the door sill

Jumper from clutch switch cable to ground

At first I thought that my ground was bad so I changed from a bolt behind the passenger glove box to that one with no success... I also changed the jumper wire to a bigger one. I still believe that the problem is the ground, I have a multimeter and knows how to check if a ground is really a ground but not if it is a good one. If any of you can explain it to me it would be very appreciated ! Thanks
Originally Posted by Vince87 ↑Hi guys ! first of all I want a thanks everyone who contributed in making this amazing mod available for everyone, especially CTScott and . I found this community while I was looking for a DIY CC installation for my Yaris, and I never thought I would be able to make it for less than 10$, thats just the coolest mod ever ! I followed very carefully your instruction and still can't make it work... Here's a few pics of my installation :
The switches
Connector D3 without CC wires
Red wire from switch to pin 40 of connector A21
Gray ground wire in the back grounded in the door sill
Jumper from clutch switch cable to ground
At first I thought that my ground was bad so I changed from a bolt behind the passenger glove box to that one with no success... I also changed the jumper wire to a bigger one. I still believe that the problem is the ground, I have a multimeter and knows how to check if a ground is really a ground but not if it is a good one. If any of you can explain it to me it would be very appreciated ! Thanks
Try soldering the wires to the switches. If you just have them twisted, they may not be making a reliable connection.
Wow ! thats a quick reply ! I'm trying that right now, I'll tell you if it works in 10 minutes...
I soldered every connections real bad and there's still nothing happening... If my understanding is good all I have to do is get to >40 mph (~60km/h on my canadian car), press the on/off button (with black and red wires) and then press on set, is that it !? If it's a ground problem, can I use a ground wire somewhere to make sure that it's not my connection to the chassis that is bad!? thanks for you help !
That is correct (it's actually >25 mph). Just to clarify, the on/off switch is the one before the resistor and the set switch is the one after the resistor.Originally Posted by Vince87 ↑I soldered every connections real bad and there's still nothing happening... If my understanding is good all I have to do is get to >40 mph (~60km/h on my canadian car), press the on/off button (with black and red wires) and then press on set, is that it !? If it's a ground problem, can I use a ground wire somewhere to make sure that it's not my connection to the chassis that is bad!? thanks for you help !
By the way, I believe that you are the first Canadian trying this.
For a ground, The bolt that you posted the picture of is a great ground point. You can strip about an inch of insulation off of the wire, wrap the wire around the bolt (under the washer) and crank the bolt back down.
Alright thanks for clarifying this point ! By the way in the meantime I tried to ground it on the battery with a wire going out the window without success... I verified if there was an internal resistance in my switches but there's none... I've been working on it (mostly making trials again and again) for more than 6 hours and I'm actually wondering if something is different on the canadian version !!??
just to be clear, you know you have to have the resistors in place, correct? A simple grounding of the pin 40 wire will not trigger the cruise, you need those resistors wired to the switches...
Yeah I know ! they're under the yellow tape on the 1st picture a few posts above... And I doubled checked for the value of the resistors with the color codes... I just cant find what I'm missing.
okay, just checking :) Anyhow, I would suggest 2 things:
1) Double, triple, etc. check those resistor values. Do you have a multimeter?
2) Check the continuity on your switches (also with a multimeter).
1) Double, triple, etc. check those resistor values. Do you have a multimeter?
2) Check the continuity on your switches (also with a multimeter).
What he said, plus make sure the switches are N.O., not N.C.
I do have a multimeter, and get a 630 ohm reading when I check the resistance at both ends of the resistors with both switches pressed.
The switches must be N.O. because if I dont press on both I dont get any reading. It's the 1st time I'm using a multimeter how can I verify the continuity of my switches??? thanks again
The switches must be N.O. because if I dont press on both I dont get any reading. It's the 1st time I'm using a multimeter how can I verify the continuity of my switches??? thanks again
With the switches you should see a high value or OL when they are not pressed and 0 ohms when they are. Or, in circuit 0 when on/off is pressed an 630 ohms when set is pressed.Originally Posted by Vince87 ↑I do have a multimeter, and get a 630 ohm reading when I check the resistance at both ends of the resistors with both switches pressed.
The switches must be N.O. because if I dont press on both I dont get any reading. It's the 1st time I'm using a multimeter how can I verify the continuity of my switches??? thanks again
My friend, you might have found my problem !
- When on/off is pressed i get a 530 ohms reading
- When set is pressed, i get 624 ohms
I have no idea why I get this 530 ohms reading... I might make another set of switches since I have 2 other swithes a lot of resistors...
- When on/off is pressed i get a 530 ohms reading
- When set is pressed, i get 624 ohms
I have no idea why I get this 530 ohms reading... I might make another set of switches since I have 2 other swithes a lot of resistors...
When in the Ohm setting, did you touch the two probes together andOriginally Posted by Vince87 ↑I do have a multimeter, and get a 630 ohm reading when I check the resistance at both ends of the resistors with both switches pressed.
The switches must be N.O. because if I dont press on both I dont get any reading. It's the 1st time I'm using a multimeter how can I verify the continuity of my switches??? thanks again
get 0 Ohms? Just checking to see that the meter is calibrated, which
could throw off your readings.
Yes I did, my multimeter is brand new so its probably well calibrated...
Did you get a chance to swap that switch out? If not, before you do, check the extra switches with the meter to make sure that they're OK.
All,
Thanks to all who have put so much effort into testing this mod. I performed the two switch mod to my wife's 07 Yaris HB with automatic trans. I used a single 670 Ohm resistor, ran the ECM wire on the passenger side through the fire wall where the rear window wash tube goes through and used the ground on the driver's side kick panel. I set up the switches for the two switch mode and before I drilled any holes, I soft wired everything in place and took a test drive.
I could not keep myself from laughing as Dr. Frankenstein must have done... "It's alive! It's alive! I have Cruise Control for less than $10!!! Halleluhah!!!"
Thanks to all for their testing and effort. The entire install took a couple hours but I was very careful about dealing with the ECM connector and the wire routing. Best of luck to all who give this a shot. It is well worth the effort. Nothing like an economy car with some of the whistles and bells of the high dollar land yachts.
Best Regards,
Wyo
Thanks to all who have put so much effort into testing this mod. I performed the two switch mod to my wife's 07 Yaris HB with automatic trans. I used a single 670 Ohm resistor, ran the ECM wire on the passenger side through the fire wall where the rear window wash tube goes through and used the ground on the driver's side kick panel. I set up the switches for the two switch mode and before I drilled any holes, I soft wired everything in place and took a test drive.
I could not keep myself from laughing as Dr. Frankenstein must have done... "It's alive! It's alive! I have Cruise Control for less than $10!!! Halleluhah!!!"
Thanks to all for their testing and effort. The entire install took a couple hours but I was very careful about dealing with the ECM connector and the wire routing. Best of luck to all who give this a shot. It is well worth the effort. Nothing like an economy car with some of the whistles and bells of the high dollar land yachts.
Best Regards,
Wyo
To CTScott :
I did check the extra switch with the meter before doing the swap and they were ok (0 resistance when unpressed, high value (1) when pressed)... I did the whole setup again without anymore luck... I just dont get it... If I take the reading at the red and black wire heres what I get when the whole setup is plugged and car is on :
- 0 ohms when nothing pressed (in an earlier post, you said I should get a high value, does that mean that my ground is still bad!?)
- 649 ohms when on/off is pressed
- 0 ohms when set is pressed
In my understanding, in my circuit, pin40 is always grounded when the switches are untouched and is grounded with a load when I press on/off... The set switch has absolutely no effect. I dont understand what I'm doing wrong...
I did check the extra switch with the meter before doing the swap and they were ok (0 resistance when unpressed, high value (1) when pressed)... I did the whole setup again without anymore luck... I just dont get it... If I take the reading at the red and black wire heres what I get when the whole setup is plugged and car is on :
- 0 ohms when nothing pressed (in an earlier post, you said I should get a high value, does that mean that my ground is still bad!?)
- 649 ohms when on/off is pressed
- 0 ohms when set is pressed
In my understanding, in my circuit, pin40 is always grounded when the switches are untouched and is grounded with a load when I press on/off... The set switch has absolutely no effect. I dont understand what I'm doing wrong...
Originally Posted by Vince87 ↑To CTScott :
I did check the extra switch with the meter before doing the swap and they were ok (0 resistance when unpressed, high value (1) when pressed)... I did the whole setup again without anymore luck... I just dont get it... If I take the reading at the red and black wire heres what I get when the whole setup is plugged and car is on :
- 0 ohms when nothing pressed (in an earlier post, you said I should get a high value, does that mean that my ground is still bad!?)
- 649 ohms when on/off is pressed
- 0 ohms when set is pressed
In my understanding, in my circuit, pin40 is always grounded when the switches are untouched and is grounded with a load when I press on/off... The set switch has absolutely no effect. I dont understand what I'm doing wrong...
It looks like you have set and on/off reversed. On/off should be 0 ohms to ground and set should be 649 ohms. With how it's wired now, just try pressing the opposite switch and see if it works.
I've already tried that.... And the on/off switch I'm speaking is the one before the resistors and were the pin40 and ground wires are attached...
I had missed this above:Originally Posted by Vince87 ↑I've already tried that.... And the on/off switch I'm speaking is the one before the resistors and were the pin40 and ground wires are attached...
"I did check the extra switch with the meter before doing the swap and they were ok (0 resistance when unpressed, high value (1) when pressed)... "
This indicates that the switches are the wrong type. They are normally closed, rather than normally open switches. Unpressed should be high resistance and pressed 0 resistance.
Wow ! I thought that normally open switches were "normally" allowing current to flow but it seems to be the opposite... sorry for that I should have checked by myself before... Thanks a lot 🙌!!!
I am not sure if I found the right one on eBay?? 🤷
This is what I am going by in my search for the switch......from the first page.
Attached picture not available
This is the closest thing I can find.....and here is the LINK to the eBay listing
Picture lost · texanurse.com
So did I find the right one?
Or can someone please send me towards the right direction, perhaps?
This is what I am going by in my search for the switch......from the first page.
Attached picture not available
This is the closest thing I can find.....and here is the LINK to the eBay listing
Picture lost · texanurse.com
So did I find the right one?
Or can someone please send me towards the right direction, perhaps?
That will work.Originally Posted by texkid ↑I am not sure if I found the right one on eBay?? 🤷
This is what I am going by in my search for the switch......from the first page.
Attached picture not available
This is the closest thing I can find.....and here is the LINK to the eBay listing
Picture lost · texanurse.com
So did I find the right one?
Or can someone please send me towards the right direction, perhaps?
That listing doesn't have a part number listed, but the correct part number is: 84632-34011
On the Camrys the same stalk as the Yaris one was used from 04 to 09.
In the picture on that listing the wire that goes from the switch to the connector on the spiral cable is missing. Part number for the wire is 84633-42030 and it goes for about $30 from the dealer.
Thank you very much. I just made an offer to the seller. In the meantime I will keep on looking around to see what else i can find.Originally Posted by CTScott ↑That will work.
That listing doesn't have a part number listed, but the correct part number is: 84632-34011
On the Camrys the same stalk as the Yaris one was used from 04 to 09.
In the picture on that listing the wire that goes from the switch to the connector on the spiral cable is missing. Part number for the wire is 84633-42030 and it goes for about $30 from the dealer.
Added Note:I was just on TRDSparks.com, their website is stating that part number 84633-42030 is being replaced with part number 84633-02020. I am not sure if that is correct so I thought I give ya'll a heads up.
84633-02020 is shown in the EPC as being for the 08-09 Corolla and Matrix, but perhaps it is the same, so they are merging the two part numbers.Originally Posted by texkid ↑Thank you very much. I just made an offer to the seller. In the meantime I will keep on looking around to see what else i can find.
Added Note:I was just on TRDSparks.com, their website is stating that part number 84633-42030 is being replaced with part number 84633-02020. I am not sure if that is correct so I thought I give ya'll a heads up.
By the way, in looking for stalks, ones from the following vehicles are all the same:
Camry 04-09
ES300 04-09
Scion TC 04-09
Sequoia 04-09
4Runner 04-09
Corolla 08-09
ES350 06-09
FJ 06, 08
GS450H 06-09
GX470 04-09
Highlander 04-09
IS F 07-09
IS250 05-09
Land Cruiser 04-09
LX470 04-09
LX570 07-09
Prius 04-09
RAV4 04-09
RX330 04-09
RX400H 05-09
Scion xB 07-09
Scion xD 07-09
Tundra 04-09
The 84633-42030 wire is supposedly only used on the following vehicles:
Corolla 08-09
RAV4 05-08
Yaris 06-09