Yarisworld Archive

Can we do this? (aka The DIY Cruise Control Thread)

498 posts · 380,332 views · page 10 of 10

Replies continued

127.0.0.1NE · Sep 25, 2009#451
I am getting a 2010 5 door HB, anyone know if it is plug-n-go ?

If not, I will be one of the first to report about it. When I get the thing I will
check for the appropriate pre-wired condition.
CTScottUSA, CT · Sep 25, 2009#452
Originally Posted by 127.0.0.1 ↑
I am getting a 2010 5 door HB, anyone know if it is plug-n-go ?

If not, I will be one of the first to report about it. When I get the thing I will
check for the appropriate pre-wired condition.
It will work just like 09's. I have the 2010 EWDs and everything with cruise is the same.
127.0.0.1NE · Sep 29, 2009#453
Originally Posted by CTScott ↑
It will work just like 09's. I have the 2010 EWDs and everything with cruise is the same.
sweet. I am going to go to electronics-r-us and get NO switches
and mygyver it the no-air-bag method.

delears wants a LOT of loot to add cruise control, probably based on what it
costs for a full install. plus more.

screw that.
nickhjortOneida, NY · Oct 3, 2009#454
Wasn't sure where to post this...a new thread or here...

1. Disconnect negative battery terminal...
Picture lost · i236.photobucket.com

2. Remove all plastics around radio and then remove gauge cluster...
Picture lost · i236.photobucket.com

3. Remove two screws in front of the gauge cluster...
Picture lost · i236.photobucket.com

4. Remove screws in both cup holders...
Picture lost · i236.photobucket.com

5. Remove glove box. Open and pop out tabs on both sides...
Picture lost · i236.photobucket.com

Picture lost · i236.photobucket.com

6. Unplug yellow airbag connector and remove two bolts with a 12mm socket...
Picture lost · i236.photobucket.com

Picture lost · i236.photobucket.com

7. Make sure you have a long socket (this one's a bit overkill) or you will knock your knuckles (it hurts) the bolts are tight...
Picture lost · i236.photobucket.com

8. Remove A-pillers. Pull back the rubber casing and pull them right off (gently)...
Picture lost · i236.photobucket.com

Picture lost · i236.photobucket.com

9. And there you have it...that's all that holds on your dash...now just pull that sucker out...
Picture lost · i236.photobucket.com

Picture lost · i236.photobucket.com

Picture lost · i236.photobucket.com

After that it's pretty much cut and splice wires to insert the Module.

10. Choose a spot to mount the module. I put mine in between the center vent outlet and the radio.
Picture lost · i236.photobucket.com

11. Connect the wires to their appropriate counterparts.
Connect the LED wires to your LED (duh)
Picture lost · i236.photobucket.com

Connect the ACC power wire to any source of ACC power (any wire that gets 12 volts when you turn the key to the ON position). I chose the pink one on the steering column (ignition connector)
Picture lost · i236.photobucket.com

And finally connect the Switch power wires. The red to your wire going from the switch to the ECM and the black to any grounding point.
Picture lost · i236.photobucket.com

12. And there you have it. Hook your battery back up quick and test it to make sure it works (unhook the battery again before you plug your airbag back in) then put everything back together.

I put my LED in the gauge cluster to make it look semi-stock. I used a white LED and scrapped a little hole in the black paint on the face plate inside the plastic housing. You can see the white dot right under the trip meter reset button. You can't even see it until you hit the CC switch so it's kind of hidden.
Picture lost · i236.photobucket.com

Hope this helps anyone planning on doing something similar. I know CTScott said he would sell these modules for $25 or so. It's a very easy install and I recommend it so you don't always have to wonder "did I already turn it on?" Let me know if you have any questions.

Video...
http://s236.photobucket.com/albums/f...t=CIMG7073.flv
sexNY · Oct 7, 2009#455
My own experience:

I used a stalk from an '05 Solara which had a cable attached to a 12-pin connector. I had to de-pin the two cruise control wires.

1. Disconnect negative cable from battery using 10mm socket wrench.
2. Unscrew left and right T30 bolts to unfasten airbag.
3. Lift airbag off steering wheel and gently pry up the yellow locking tabs.
4. Remove horn cable from clockspring and disconnect from airbag.
5. Lift locking tab from connector and insert the two stalk wires.
6. Drilled out rear steering wheel cover by aligning stalk and eyeballing position.
7. Fastened stalk, seated cable into clip, and plugged into clockspring.
8. Plugged in airbag, secured bolts, and reconnected battery.
2.JPG3.JPG4.JPG5.JPG6.JPG7.JPG8.JPG9.JPG10.JPG11.JPG
Doc ZaiusOttawa, ON, Canada · Jan 14, 2010#456
Bump!

I just spent 2 hours reading this *whole* thread. Wow. You guys are awesome... I love these pioneering threads. So much excitement and discovery... reminds me of the Blitz install threads from the summer of '08! 😁

I just bought a stalk for my Canadian '06 hatch (RS). I figure I'll be running wires to the ECM. But how I would love it if the RS trim happened to have the dash lights already!

In fact, I'm going to go out into the garage right now *brrrr* with a flashlight and find out! (Won't be doing the install until warmer weather though!) -- EDIT: Nope... no dash light. 😢

Anyhow, thanks to all... YW FTW! 👍
goku87AK · Jan 15, 2010#457
Originally Posted by CTScott ↑
It will work just like 09's. I have the 2010 EWDs and everything with cruise is the same.
Woah woah woah woah woah, where did you get those?

Think you can get the rest of the factory repair manual?? :D:D:D:D
CTScottUSA, CT · Jan 15, 2010#458
Originally Posted by goku87 ↑
Woah woah woah woah woah, where did you get those?

Think you can get the rest of the factory repair manual?? :D:D:D:D
Toyota techinfo. Unfortunately, because of the way they serve the data, it is nearly impossible to grab the entire manual, but I have the sections for the 2009 and 2010 that differ from the 2007 manual (TPWS, VSC, TRAC, etc.)
goku87AK · Jan 15, 2010#459
Originally Posted by CTScott ↑
Toyota techinfo. Unfortunately, because of the way they serve the data, it is nearly impossible to grab the entire manual, but I have the sections for the 2009 and 2010 that differ from the 2007 manual (TPWS, VSC, TRAC, etc.)
I didn't even know that site existed. NEAT.
stveebristol, tn · Mar 17, 2010#460
Is the wire included if I order one of these from toyota parts zone?

84632-08021

Two months old and all, but this seems like the thread to beat.
CTScottUSA, CT · Mar 17, 2010#461
Originally Posted by stvee ↑
Is the wire included if I order one of these from toyota parts zone?

84632-08021

Two months old and all, but this seems like the thread to beat.
No, you also need to order 84633-02020 to get the wire.
stveebristol, tn · Mar 19, 2010#462
I know I'm getting off light because I'm an 09, but how much harder is it to replace the steering wheel wheel cover rather than drilling the hole? Fear of the clockspring seems to be a recurring theme in these threads.
CTScottUSA, CT · Mar 19, 2010#463
Originally Posted by stvee ↑
I know I'm getting off light because I'm an 09, but how much harder is it to replace the steering wheel wheel cover rather than drilling the hole? Fear of the clockspring seems to be a recurring theme in these threads.
It's really not that bad. I pulled my steering wheel recently to install the leather steering wheel that I bought from a member from Germany. You just want to be careful with the clock spring, as it is quite expensive (>$200).
stveebristol, tn · Mar 23, 2010#464
Parts are pretty close and I'm still trying to get up the nerve to do this myself.

Could you be a little more specific about being careful with the clockspring? From this thread it looks like the biggest concerns would be not spinning the clockspring and not damaging the wires coming out of it. What else do I need to look out for?

All this cause I don't want to pay a guy a hundred and fifty bucks.
CTScottUSA, CT · Mar 23, 2010#465
Originally Posted by stvee ↑
Parts are pretty close and I'm still trying to get up the nerve to do this myself.

Could you be a little more specific about being careful with the clockspring? From this thread it looks like the biggest concerns would be not spinning the clockspring and not damaging the wires coming out of it. What else do I need to look out for?

All this cause I don't want to pay a guy a hundred and fifty bucks.
Those are the main concerns. Also, the clockspring's plastic is somewhat fragile, so just be careful not to smack it while working around the steering column with the wheel removed.
stveebristol, tn · Mar 27, 2010#466
Well, in as much as I didn't ruin the steering wheel, clockspring, horn, or airbag, it went ok. Getting nothing out of the cruise, though. Was I supposed to have the power package or something? Boy I feel terrible.

Automatic 09 sedan and this guy.

CTScott, you've been incredibly kind.
CTScottUSA, CT · Mar 27, 2010#467
Originally Posted by stvee ↑
Well, in as much as I didn't ruin the steering wheel, clockspring, horn, or airbag, it went ok. Getting nothing out of the cruise, though. Was I supposed to have the power package or something? Boy I feel terrible.

Automatic 09 sedan and this guy.

CTScott, you've been incredibly kind.

On the connector at the other end of the clock spring (the one on the bottom of the steering column) does your sedan have the blue and brown wires, or just the black wire?

Some of the 09 sedans have the wiring from the ECM to that connector, others do not (and hence you have to run the wire from the connector to the ECM poin 40). All 09 LBs had that wire run, but not all Sedans.
stveebristol, tn · Mar 27, 2010#468
Took off steering column cover and I've got one black wire. Still calling this a win if I don't have to take the steering wheel off anymore.

So two wires where the blue and brown ones would be. Which one goes where? All the crosstalk between autos and manuals and stalks and switches has jellied my brain. Should I switch to PM or something? I'm feeling less potentially instructive by the minute.
CTScottUSA, CT · Mar 28, 2010#469
Originally Posted by stvee ↑
Took off steering column cover and I've got one black wire. Still calling this a win if I don't have to take the steering wheel off anymore.

So two wires where the blue and brown ones would be. Which one goes where? All the crosstalk between autos and manuals and stalks and switches has jellied my brain. Should I switch to PM or something? I'm feeling less potentially instructive by the minute.
The Blue is the wire that needs to be run to the ECM. The brown is a ground.



In this thread, I have the part numbers for the pins for that connector:

DIY Cruise Control FAQ (2006-2010 Yaris)
stveebristol, tn · Apr 10, 2010#470
We are talking about the connector furthest left of that picture, right? I ordered two spiral connector repair terminals and one ecm repair terminal. The connector in the ecm repair terminal looked like a perfect fit for the ones in the steering column. Should I go for two more of those or do I have the wrong connector?
CTScottUSA, CT · Apr 10, 2010#471
Originally Posted by stvee ↑
We are talking about the connector furthest left of that picture, right? I ordered two spiral connector repair terminals and one ecm repair terminal. The connector in the ecm repair terminal looked like a perfect fit for the ones in the steering column. Should I go for two more of those or do I have the wrong connector?
Yes - Left most connector. The pins are slightly different for the ECM and the spiral cable connector. The part numbers are listed in this thread:

DIY Cruise Control FAQ (2006-2010 Yaris)
rhaagusafort walton bch fl · May 11, 2010#472
Did you get your stalk from Thailand working? If so, what did you need to do? Robert
rhaagusafort walton bch fl · May 11, 2010#473
I just received the stalk (Thailand eBay, $30) to use on a new 2010 sedan automatic. It came with a wire (2 wires attached to the white plastic clip/plugs at each end). Can anyone tell me if I just plug it in as is, or do I need to switch over what has been called the airbag or horn ground wire?
CTScottUSA, CT · May 11, 2010#474
Originally Posted by rhaagusa ↑
I just received the stalk (Thailand eBay, $30) to use on a new 2010 sedan automatic. It came with a wire (2 wires attached to the white plastic clip/plugs at each end). Can anyone tell me if I just plug it in as is, or do I need to switch over what has been called the airbag or horn ground wire?
If it came with a cable that has a white four pin connector, with two going to the stalk, one empty and one going to a female spade lug, then you pull off the existing horn cable and plug the new one into the horn and connect it to the spiral cable connector.

If it came with a cable that has the white connector, but lacks the horn wire, then you have to remove the horn wire from the existing white connector and transfer it to the new one.
rhaagusafort walton bch fl · May 12, 2010#475
Thanks CTScott and all for the info. I did later find the answer to this question had been answered earlier. So much info and so many threads. We're really happy and thankful to be getting cruise so inexpensively and easily. Robert H
rhaagusafort walton bch fl · May 12, 2010#476
Went by the dealer to get the proper screws which they didn't have, but found out they appear to be 5mm. I checked at Loews and 10/32 does fit loosely in a 5mm nut, but 5mm should fit right.
One more question please: While I was there he showed me a little pack of what I think was 2 black wires, and some zip ties. He said it was required, and it cost $12. At one end was the very small ends that go in the white clip type connectors, and at the other end of one was a screw down round tab type like used for a ground, that fits under a nut or screw head. Couldn't see the other ones end through the baggy packaging.
So anyway what are these wires and are they needed on a 2010 sedan automatic? If so where do they go and are there any directions and pics posted?
Hoping to only go in there once, so thanks very much, Robert
CTScottUSA, CT · May 12, 2010#477
Originally Posted by rhaagusa ↑
Went by the dealer to get the proper screws which they didn't have, but found out they appear to be 5mm. I checked at Loews and 10/32 does fit loosely in a 5mm nut, but 5mm should fit right.
One more question please: While I was there he showed me a little pack of what I think was 2 black wires, and some zip ties. He said it was required, and it cost $12. At one end was the very small ends that go in the white clip type connectors, and at the other end of one was a screw down round tab type like used for a ground, that fits under a nut or screw head. Couldn't see the other ones end through the baggy packaging.
So anyway what are these wires and are they needed on a 2010 sedan automatic? If so where do they go and are there any directions and pics posted?
Hoping to only go in there once, so thanks very much, Robert

Can you post a picture of what wiring you received with your stalk? From that I can tell you whether you need the wires he was trying to sell you.

As for the screws, the one that I bought (attached to a Scion steering wheel) had the screws with it. I just checked with my extra steering wheel and an 8-32 screw fits. I don't have a 5mm to try, but I tried 5mm taps (fine and coarse) and they seem to be too big for the hole.

Here's a picture of my Scion one mounted and wired. The Scion cruise cable had a different spiral cable connector, so I pulled the pins out of the connector and moved them to the Yaris connector.


Cruise Stalk.jpg
rhaagusafort walton bch fl · May 13, 2010#478
As you've probably seen, the ebay Thailand stalk photo doesn't show the connector. though the connector looks just like the one in your photo with spots to accept 4 wires, though it comes with just 2 wires coming from the stalk. It's also the same as the ones in photos 3, 4, and 5 posted here (though it has no horn/ ground which as you said I'll be transferring):
http://www.toyotanation.com/forum/sh...171992&page=22[IMG]

I'm wondering if the wires the parts guy showed me are for wiring to the ECM, though th chart you posted (man you're really on top of all these threads) says my 2010 automatic Sedan doesn't need these. What do you think?
DIY Cruise Control FAQ (2006-2010 Yaris)

Again, thank you so much! Robert
CTScottUSA, CT · May 13, 2010#479
Originally Posted by rhaagusa ↑
As you've probably seen, the ebay Thailand stalk photo doesn't show the connector. though the connector looks just like the one in your photo with spots to accept 4 wires, though it comes with just 2 wires coming from the stalk. It's also the same as the ones in photos 3, 4, and 5 posted here (though it has no horn/ ground which as you said I'll be transferring):
http://www.toyotanation.com/forum/sh...171992&page=22[IMG]

I'm wondering if the wires the parts guy showed me are for wiring to the ECM, though th chart you posted (man you're really on top of all these threads) says my 2010 automatic Sedan doesn't need these. What do you think?
DIY Cruise Control FAQ (2006-2010 Yaris)

Again, thank you so much! Robert

If your Thailand one has the two wires from the stalk (in the positions shown in my picture above) then you don't need the wires that your parts guy showed you. The wires you described would be for adding the two connections from the stalk to the existing connector.

As for the ECM run, it seems to be hit or miss with 09 sedans. You'll have to look at the spiral cable connector, under the steering wheel for the brown and blue wires, and then also check the ECM connector to see if pin 40 is populated.
rhaagusafort walton bch fl · May 13, 2010#480
OK, sounds good. I'll look to check for the brown and blue wires, and ECM connector and pin 40. Are these all easily visible with the air bag off, or can you direct me to any threads with info on checking these.
CTScottUSA, CT · May 13, 2010#481
Originally Posted by rhaagusa ↑
OK, sounds good. I'll look to check for the brown and blue wires, and ECM connector and pin 40. Are these all easily visible with the air bag off, or can you direct me to any threads with info on checking these.
No need to pull the airbag. Just remove the lower steering column cover to see the spiral cable connector (the one in the lower left is the connector you are looking for). It will either have just a black wire, or will have the black, brown and blue like this picture:




For the ECM connector, you have to pop the connector, and then you can look at the business end of the connector to see if the pin is populated (shining a flashlight into the connector will help you to see if the metal pin is in the hole for pin 40).
rhaagusafort walton bch fl · May 13, 2010#482
Thanks for your patience. Hope this is not sounding too dumb; how do I remove the lower steering column cover, and how do you tell which is pin # 40. Is it labeled?
CTScottUSA, CT · May 13, 2010#483
Originally Posted by rhaagusa ↑
Thanks for your patience. Hope this is not sounding too dumb; how do I remove the lower steering column cover, and how do you tell which is pin # 40. Is it labeled?
This thread shows the location of the three screws for removing the lower steering column:

DIY - 2009 Cruise Control for $10, without pulling the steering wheel and airbag


And, this one shows the details of checking pink 40 on the ECM connector. The pins are not labeled, but you can easily find the pin 40 position with the photo as a reference.

DIY Cruise Control on 07-08 Yaris (step by step)
rhaagusafort walton bch fl · May 13, 2010#484
Got it. Doesn't look to hard. With gratitude, RH
CtrlAltDefeatIndianapolis IN · Nov 26, 2010#485
Originally Posted by yarismadness ↑
Guys,

I had I idea, and i need your opinion before trying it.

The yellow wire on the clutch switch that blocks the start (i am talking about the one on the bottom, not the additional we should add to stop the cruise), has normally (when released) 12V, high impedance (my guess is a pull up resistor inside the ECU). when pressed (the clutch needs to go to the bottom), that line goes near 0V (pulled down by the starter relay coil).

What if we sense that in order to stop the cruise? For example, a mosfet transistor will do the job perfectly.

The problem: the cruise will disable ONLY if the clutch is COMPLETELY pressed. What will happen during the clutch travel?
Cheers!
I'm not an expert but I'm pretty sure the engine will rev up. disengaging the clutch will slow the car, which the ecu will see and will give it more gas to try to maintain speed. most of the time you do not floor the clutch (which would be required for this to disengage the cruise). I personally would not like this solution...
CTScottUSA, CT · Nov 26, 2010#486
^Exactly. The starting clutch switch and the cruise clutch switch have exactly opposite purposes. The starting one is a "safety" which wants to see the clutch fully depressed and the cruise one cancels cruise mode to prevent revving as soon as the clutch is touched. The OEM clutch switch is under $20, so it's really not worth looking for an alternative solution.
teddyOntario, Canada · Jan 15, 2011#487
How is everyone running the wire from D3 to the ECM connector A21?
Last night I tried to follow the conduit of wires running from the ECM in the engine bay without much luck. I didn't want to have to rip apart the engine bay to find out where it goes. I really feel like I'm missing something silly!
CTScottUSA, CT · Jan 15, 2011#488
Originally Posted by teddy ↑
How is everyone running the wire from D3 to the ECM connector A21?
Last night I tried to follow the conduit of wires running from the ECM in the engine bay without much luck. I didn't want to have to rip apart the engine bay to find out where it goes. I really feel like I'm missing something silly!
The easiest way is to enter the rubber grommet above the ECM or the one below it (which is actually the grommet around the AC drain hose). Then, once you are through the firewall on the passenger side, you can bring the wire across to the driver's side.
mgoldhawkZimbabwe · Mar 14, 2011#489
Would I be able to fit cruise control to my Yaris using the same method? I have a 2001 5door hatchback...
CTScottUSA, CT · Mar 14, 2011#490
Originally Posted by mgoldhawk ↑
Would I be able to fit cruise control to my Yaris using the same method? I have a 2001 5door hatchback...
No. 1999-2005 Yaris used a cable throttle, rather than an electronic one like 2006 and newer ones have. So, 1st gen Yaris require an electro-mechanical cruise control system.
Pauleemississauga · Nov 9, 2015#491
Hey guys. Got myself an 09 Yaris recently and want to add the cruise. Ordered the OEM stalk from China and was wondering if I will need a clutch switch too. I know the guide says I do but shouldn't the car already have one? havent tried starting it without pressing the clutch in (force of habit) but the switch should prevent the car from rolling forward on the starter no?

apologize in advance if this was already covered elsewhere.

-Paul
SecretblendUnited States · Nov 9, 2015#492
Originally Posted by Paulee ↑
Hey guys. Got myself an 09 Yaris recently and want to add the cruise. Ordered the OEM stalk from China and was wondering if I will need a clutch switch too. I know the guide says I do but shouldn't the car already have one? havent tried starting it without pressing the clutch in (force of habit) but the switch should prevent the car from rolling forward on the starter no?

apologize in advance if this was already covered elsewhere.

-Paul
It does have a switch that tells the car you are pressing the clutch all the way in. It is not same switch that you would need to install that tells the car your clutch is all the way out.

the two switches would be on opposite side of clutch. If clutch is fully engaged the one switch would be used. If clutch is not engaged at all, other switch would be used. If clutch is halfway between then both switch would not be used.
Pauleemississauga · Nov 9, 2015#493
thanks. since posting I went through all the pages and some associated links. Think I have a good grip on what to do. just waiting for my stalk to arrive. might skip the clutch switch for now and drive around it. sounds like I dont have to dig under the dash and engine bay if I do save it for never.
SecretblendUnited States · Nov 9, 2015#494
Originally Posted by Paulee ↑
thanks. since posting I went through all the pages and some associated links. Think I have a good grip on what to do. just waiting for my stalk to arrive. might skip the clutch switch for now and drive around it. sounds like I dont have to dig under the dash and engine bay if I do save it for never.
For me, the wiring was tied down by wire tie just above the clutch.. Cut the wire tie and pull wiring down and there it is ready to plug into the switch.

By my logic, If you don't have switch installed, the car will be thinking the clutch is not engaged and therefore cruise control won't turn on.

If I am wrong and it works, just be careful cause if you have CC engaged and you press down on clutch, the engine will rev up quickly and could damage engine if you leave it revving long enough.
Pauleemississauga · Nov 9, 2015#495
U got a hatch or sedan? Next chance i get i check for the plug
SecretblendUnited States · Nov 9, 2015#496
Originally Posted by Paulee ↑
U got a hatch or sedan? Next chance i get i check for the plug
Sedan.
Pauleemississauga · Dec 6, 2015#497
got my CC installed today and loving it. Best $20 I spent. Still haven't got the clutch switch kit yet so had to jump the connector for it to work and yes, the revs jump when u step on the clutch with the cruise set. overall pretty simple install tho.
mumairrIslamabad, Pakistan · Jul 22, 2017#498
My Vitz 2010 model already has wiring upto ECM (saw it by removing the cover behind the steering )but my cluster doesn't have any indicators for CC. Do you think if i install OEM CC, my car would be able to handle it? irrespective of the indication on the cluster? if this is the case, i might change my insturmenet cluster.