Thanks, just ordered from TRDSparks. Should be getting the fogs, OEM combo stalk, shrouds, clutch switch, and boss this weekend to go with the cruise stalk. I figure I'll pull the steering wheel once and be done with it.
Can we do this? (aka The DIY Cruise Control Thread)
498 posts · 380,332 views · page 6 of 10
Replies continued
CTScott, I checked every pin (just to be sure) on those two IC's (IC500,IC501) and the pins for the blank spot where the third IC should go (IC502). Nothing :( they were all the same after I hit the Cruise switch. I grounded my meter to the frame and checked the pins with the red lead of the meter while it was on DC Voltage "20V" setting. That's how I do it right (I don't think I'm that dumb, but just to make sure) I guess it's not gunna happen the easy way as usual :)
Originally Posted by nickhjort ↑CTScott, I checked every pin (just to be sure) on those two IC's (IC500,IC501) and the pins for the blank spot where the third IC should go (IC502). Nothing :( they were all the same after I hit the Cruise switch. I grounded my meter to the frame and checked the pins with the red lead of the meter while it was on DC Voltage "20V" setting. That's how I do it right (I don't think I'm that dumb, but just to make sure) I guess it's not gunna happen the easy way as usual :)
Sounds like you tested it correctly. As PK mentioned prior, there was little chance that it would be there, but it was worth a shot. I have to order some parts today for another project, so I'll order what I need as well to test my method of lighting your LED.
Awsome. Thanks.
CTScott and nickhjort, you guys are awesome. keep up the good work.
this info is super helpful. i will do this on my car once i have some downtime. i have an 07 auto, FYI.
this info is super helpful. i will do this on my car once i have some downtime. i have an 07 auto, FYI.
Thanks. It feels good to be able to actually help for once instead of just sucking in all the information and hard work of others to make my car better :) I like being one of the first to do a mod.
This is a little off topic but does anyone out there know where I can find the leather wrapped steering wheel? Even just the toyota part number would be great
"a little off topic?" 😆Originally Posted by MGargano ↑This is a little off topic but does anyone out there know where I can find the leather wrapped steering wheel? Even just the toyota part number would be great
Ok... a lot off topic. It's just that I'm pulling the steering wheel to install the cruise and fog light stalks, so I thought if I could find the leather steering wheel I'd be able to do it all at the same time.Originally Posted by tk-421 ↑"a little off topic?" 😆
guys. TCScott, nickhjort, i need help.😲😳
thats what i did. i build a prototype remote with the swich assembly in it.one swich sends a 0.0002 ohm and the other sends 630ohm.
(view pictures in super size by clicking on it)
Picture lost · www.got2pic.com
Picture lost · www.got2pic.com
thats my car to get the impression its the SOL model hatchback 2007.
Picture lost · www.got2pic.com
ok one wire from the resistors side as nickhjort and TSCott did (the red wire) connected to pin 40
Picture lost · www.got2pic.com
and the black wire from the other button side i connected to some grounded wire i found. then started to drive and testing it. as soon i pressd the on-off button the "check engine" light turnd on.
i turnd off the car and then started my engine on. now no light are on. i pressd the on-off button again and now no warning light turning on - wich is good. but no respond from the cruise controll. no respond to pressing the set button. thr car continue to listen my gas pedal.
anyway. i got home and tested the wires. seems that i dont have anough ground in the wires (22.1 U) so i took the black ground wire from the swich assembly and connected him directly to the battery negetive terminal
Picture lost · www.got2pic.com
now we have an exellant ground
anyway i tried the system again on the highway and yet. no response.
and then i figure that i dont actually have a manual transsmision nor automatic transmission. i have a robotic transmission. so maybe the ECM based on MT maybe i need to jump a cluch swich (even that i dont have cluch😕)
i opend the fuse box
Picture lost · www.got2pic.com
and there isnt the cluch blue wire in the connector. i can see another blue wire. but i think its isnt the cluch wire
Picture lost · www.got2pic.com
please help🙇
thats what i did. i build a prototype remote with the swich assembly in it.one swich sends a 0.0002 ohm and the other sends 630ohm.
(view pictures in super size by clicking on it)
Picture lost · www.got2pic.com
Picture lost · www.got2pic.com
thats my car to get the impression its the SOL model hatchback 2007.
Picture lost · www.got2pic.com
ok one wire from the resistors side as nickhjort and TSCott did (the red wire) connected to pin 40
Picture lost · www.got2pic.com
and the black wire from the other button side i connected to some grounded wire i found. then started to drive and testing it. as soon i pressd the on-off button the "check engine" light turnd on.
i turnd off the car and then started my engine on. now no light are on. i pressd the on-off button again and now no warning light turning on - wich is good. but no respond from the cruise controll. no respond to pressing the set button. thr car continue to listen my gas pedal.
anyway. i got home and tested the wires. seems that i dont have anough ground in the wires (22.1 U) so i took the black ground wire from the swich assembly and connected him directly to the battery negetive terminal
Picture lost · www.got2pic.com
now we have an exellant ground
anyway i tried the system again on the highway and yet. no response.
and then i figure that i dont actually have a manual transsmision nor automatic transmission. i have a robotic transmission. so maybe the ECM based on MT maybe i need to jump a cluch swich (even that i dont have cluch😕)
i opend the fuse box
Picture lost · www.got2pic.com
and there isnt the cluch blue wire in the connector. i can see another blue wire. but i think its isnt the cluch wire
Picture lost · www.got2pic.com
please help🙇
All I can say is to pull the wire from the ecm connector and check that it is making good contact with the pin on the ecm. Make sure that you stripped the wire back far enough so that the copper pushes out of the hole just a little bit that way you know it's gunna hit (see picture). Just make sure they're in pin #40 hole...not #29 like I had them in the picture :)
Picture lost · i236.photobucket.com
Check all your connections (solder points, ground points, etc.)
Also, just to be certain, your resistors are on the side of the switches going to pin#40 right? Not on the ground side? And remember, the switch sending 0 ohms is the on/off and the one with 630 ohms is the set.
As for the transmission, I'm not really sure the difference between the "robotic" and automatic. You definatly don't have the clutch switch wire, so don't worry about that. Maybe CTScott knows exactly what's wrong. Sorry I can't help more 🤷
Picture lost · i236.photobucket.com
Check all your connections (solder points, ground points, etc.)
Also, just to be certain, your resistors are on the side of the switches going to pin#40 right? Not on the ground side? And remember, the switch sending 0 ohms is the on/off and the one with 630 ohms is the set.
As for the transmission, I'm not really sure the difference between the "robotic" and automatic. You definatly don't have the clutch switch wire, so don't worry about that. Maybe CTScott knows exactly what's wrong. Sorry I can't help more 🤷
Hmmmm, I'd really like to see the wiring diagram for your car to see what the differences are.
In the under-hood fuse box, where the blue wire should be for the clutch switch on a MT, there should be a park/neutral blue wire on an AT car.
In the under-hood fuse box, where the blue wire should be for the clutch switch on a MT, there should be a park/neutral blue wire on an AT car.
i'm preety sure that the 40'th pin contacting the wire. i couldent get the wire out a little bit because the wire was too wide to the pin hole. but its gone all the way in and can see it from the other side.
the wire to that pin is connected to the resistors side of the buttons.
the first button givs about 0U and the second button with the resistor at one side givs 0.630 (3 resistors 120/120/390 ohm) it connected like TCScott's module but with another resistors.

this is a prototype i havent weld any connection yet. just catch the wire ectch other and used isolear-band...
any ideas?
the wire to that pin is connected to the resistors side of the buttons.
the first button givs about 0U and the second button with the resistor at one side givs 0.630 (3 resistors 120/120/390 ohm) it connected like TCScott's module but with another resistors.

this is a prototype i havent weld any connection yet. just catch the wire ectch other and used isolear-band...
any ideas?
oooops... so your telling me that i dont have the cruise controll abillity in my car?Originally Posted by CTScott ↑Hmmmm, I'd really like to see the wiring diagram for your car to see what the differences are.
In the under-hood fuse box, where the blue wire should be for the clutch switch on a MT, there should be a park/neutral blue wire on an AT car.
i dont think the toyota dealer/gerage will give me a wire diagram...
any ideas?
Can you PM me the VIN number for your car?Originally Posted by mariann ↑oooops... so your telling me that i dont have the cruise controll abillity in my car?
i dont think the toyota dealer/gerage will give me a wire diagram...
any ideas?
I am looking at the wiring diagrams now for European Yaris and I see no mention of cruise control for any of the Yaris from 2005-2009.
where i can find the VIN number? driver side door frame? driver book?
Either on the drivers side door frame label, or on a metal tag, where the dashboard meets the windshield, that is visible from the outside of the car, or under the hood, above the engine, in the center.Originally Posted by mariann ↑where i can find the VIN number? driver side door frame? driver book?
I think the VIN is 12 or 13 characters.
i'v PM you but just in caseOriginally Posted by CTScott ↑Either on the drivers side door frame label, or on a metal tag, where the dashboard meets the windshield, that is visible from the outside of the car, or under the hood, above the engine, in the center.
I think the VIN is 12 or 13 characters.
there are two numbers
VNKKL98377A070674
and
SCP90L-CHGGKW
OK. I looked up your VIN / Model code (SCP90L). It looks like none of the European Yaris even have cruise as an option.
I just verified with one of our members that works at a dealership in Europe, that cruise is not an OEM option on European Yaris. To add it a ~$500 aftermarket system is required.
holly cow!!!!
there isnt a way to jump few wires, cutting others and it will work?
like jumping to pin 56 at ECM?
Picture lost · www.got2pic.com
there isnt a way to jump few wires, cutting others and it will work?
like jumping to pin 56 at ECM?
Picture lost · www.got2pic.com
I don't think so. It looks like the ECM is just not even programmed to support it.Originally Posted by mariann ↑holly cow!!!!
there isnt a way to jump few wires, cutting others and it will work?
like jumping to pin 56 at ECM?
Picture lost · www.got2pic.com
Damn that sucks dude. I'm sorry that it's not able to be done with your car. What if you get an ECM from a yaris like ours? Or will that even work...CTScott?
Not with his transmission. Also, even a used ECM would be more expensive then the aftermarket cruise kit.Originally Posted by nickhjort ↑Damn that sucks dude. I'm sorry that it's not able to be done with your car. What if you get an ECM from a yaris like ours? Or will that even work...CTScott?
I see...good to know :)
is it possible to order the side cover piece from the factory with the hole already there? I am sloppy with a drill and dremmell and don't want a hack job.
Cover, Steering Wheel Boss, Lower: 45184-52130-B0Originally Posted by regal ↑is it possible to order the side cover piece from the factory with the hole already there? I am sloppy with a drill and dremmell and don't want a hack job.
This is for one that has the hole for factory cruise control.
Originally Posted by nickhjort ↑CTScott, I checked every pin (just to be sure) on those two IC's (IC500,IC501) and the pins for the blank spot where the third IC should go (IC502). Nothing :( they were all the same after I hit the Cruise switch. I grounded my meter to the frame and checked the pins with the red lead of the meter while it was on DC Voltage "20V" setting. That's how I do it right (I don't think I'm that dumb, but just to make sure) I guess it's not gunna happen the easy way as usual :)
I received the parts this week for lighting your LED, without changing your switch. I will be using a PIC12HV615 microcontroller to sense the switch press (and differentiate between the on/off and one of the other ones being pressed) and to drive the LED. The entire circuit will only require the 8 pin microcontroller, a transistor, and a few resistors (totaling maybe $5 in parts).
I will hopefully have some time this weekend to experiment. PM me your mailing address, and when I have it all figured out, I'll mail you the "module" (at no charge, since you've been the guinea pig for this).
Damn man that's awesome...PM sent.
Thanks so much for all the help with this project. It's not so bad being the guinea pig on something when you have so much knowledgable help on the subject. Hopefully we can get this thing hooked up and write up a nice DIY for the other "cruise control-wire-missing" drivers here :)
Thanks so much for all the help with this project. It's not so bad being the guinea pig on something when you have so much knowledgable help on the subject. Hopefully we can get this thing hooked up and write up a nice DIY for the other "cruise control-wire-missing" drivers here :)
Alright, so just to sum it up for the stalk usage: I remove the airbag, install the stalk like in that Matrix link, then run a wire from the D connector to a ground point, and then the other wire straight to pin #40 in the ECM?
Do I mess with A21, or do I just do what I wrote in the above paragraph? (and this is all just if I don't bother with the clutch switch just yet)
Do I mess with A21, or do I just do what I wrote in the above paragraph? (and this is all just if I don't bother with the clutch switch just yet)
Correct.Originally Posted by mrbond ↑Alright, so just to sum it up for the stalk usage: I remove the airbag, install the stalk like in that Matrix link, then run a wire from the D connector to a ground point, and then the other wire straight to pin #40 in the ECM?
Do I mess with A21, or do I just do what I wrote in the above paragraph? (and this is all just if I don't bother with the clutch switch just yet)
Remember that in order to even test it, you will need to bypass the clutch switch at the under hood fuse panel connector.
^ right, you said to jumper it to the white wire 2 pins over? What do you mean by jumper?
Basically, make the connection. Since it is temporary, until you get the switch, I would just shove a stiff piece of wire from the blue to the white.Originally Posted by mrbond ↑^ right, you said to jumper it to the white wire 2 pins over? What do you mean by jumper?
nickhjort, did you find any connector for the wiring to the clutch switch? Been searching for it for a few hours and haven't found anything. I believe that only the 09+ mt Yarii have that plug just hanging there...
Also, what is the function of the white wire you jumped the blue clutch switch wire to? Did you just do like what CTScott said and stuffed one wire into both pins?
Also, what is the function of the white wire you jumped the blue clutch switch wire to? Did you just do like what CTScott said and stuffed one wire into both pins?
Yeah basically I just used a thick guage wire I had laying around, that just happened to have a fuse on it, and just stuck it in there. You probably don't need the fuse, but what the hell...you can never have too many fuses right :) And no I didn't find the clutch switch connector under there either. I am still going to buy the stock switch though and just wire it to where I have the jumper in the fuse box. Basically what the switch does is acts as the jumper wire...only it's a reversed switch. So when you hit the clutch it kills the circuit (just like if you were to pull the jumper wire while using cruise control) Here's some pics of my jumper. Also make sre you put some spade connectors on the ends of your wire. They fit in there perfectly, nice and tight to ensure it doesn't come loose.
Picture lost · i236.photobucket.com
Picture lost · i236.photobucket.com
Hope it helps 👍
Picture lost · i236.photobucket.com
Picture lost · i236.photobucket.com
Hope it helps 👍
PS... Make sure whatever you use as a jumper will fit under there whenever you put the fuse box cover back on :) Mine just barely fits.
so thats all you have to do to bypass the secondary clutch switch for the MT?Originally Posted by nickhjort ↑PS... Make sure whatever you use as a jumper will fit under there whenever you put the fuse box cover back on :) Mine just barely fits.
Wow, that actually cleared things up a lot, thanks!
Yup that's it and everything to bypass the MT clutch switch. Now if you are using cruise control and you hit the clutch the engine will rev like a mofo since there's no switch to stop it...so don't hit the clutch! Unless you wanna blow shit up 👍
Also I'm probably going to try to make my own clutch switch, seeing as it's only a momentary switch held down bt the clutch. I'd rather spend another 2 bucks on the switch then 19 at the dealer. I'll post pics once I finish it.
So...theoretically I wouldn't even need to remove the dashboard if I'm using the stalk. If I reuse a ground point on the driver's side kick panel next to the hood release, and just thread all the necessary wires through the firewall, then that's the end of that. Now, this is exciting.
Definitely don't remove the dash, since the junction point under there is not populated. It's just a straight run from the stalk connector to the ECM.Originally Posted by mrbond ↑So...theoretically I wouldn't even need to remove the dashboard if I'm using the stalk. If I reuse a ground point on the driver's side kick panel next to the hood release, and just thread all the necessary wires through the firewall, then that's the end of that. Now, this is exciting.
By the way, if anyone has the clutch switch on hand, could you post a picture of the connector? I believe I may have found the necessary wire plug. It was taped up with a bunch of other wires by the clutch pedal, so....
The connector is a two pin one with a black and a blue wire.Originally Posted by mrbond ↑By the way, if anyone has the clutch switch on hand, could you post a picture of the connector? I believe I may have found the necessary wire plug. It was taped up with a bunch of other wires by the clutch pedal, so....
so instead going through the hassle of buying the secondary clutch switch for the cruise, I should be able to use those two jump points in the fuse box and wire a momentary button to shut it off? and then I can just press the "on" and "set" to start the cruise again?Originally Posted by nickhjort ↑Yup that's it and everything to bypass the MT clutch switch. Now if you are using cruise control and you hit the clutch the engine will rev like a mofo since there's no switch to stop it...so don't hit the clutch! Unless you wanna blow shit up 👍
Originally Posted by AlexNet0 ↑so instead going through the hassle of buying the secondary clutch switch for the cruise, I should be able to use those two jump points in the fuse box and wire a momentary button to shut it off? and then I can just press the "on" and "set" to start the cruise again?
Actually, just press set again (or resume if you do the four button method). Only on/off or the keyswitch completely clear cruise mode.
yeah, I bought the OEM stalkOriginally Posted by CTScott ↑Actually, just press set again (or resume if you do the four button method). Only on/off or the keyswitch completely clear cruise mode.
Well, I found an unused wire plug, but it's clearly the wrong one. I wonder what this one's for?
Anyway, AllexNet0, I'll be installing the stalk on sunday hopefully. I'll take a bunch of pictures for each step of the way. And we'll see what happens with the clutch switch wiring that nickhjort was talking about.
Anyway, AllexNet0, I'll be installing the stalk on sunday hopefully. I'll take a bunch of pictures for each step of the way. And we'll see what happens with the clutch switch wiring that nickhjort was talking about.
Hey nickhjort, did you ever figure out that homemade clutch switch? I think a lot of us are anxiously waiting to see if that works! Let us know asap thanks!
Yeah tomorrow I will be "frankenstein"ing it together. I haven't had time yet, but tomorrow I will hopefully have it done, and I will also mock up an exhaust idea I had. I will take pictures of both :)
Motorcycle Exhaust on a Yaris!
Motorcycle Exhaust on a Yaris!