Yarisworld Archive

2ZR Turbo Yaris

561 posts · 343,257 views · page 9 of 12

Replies continued

06YarisRSThread starterFredericton, New Brunswick, Canada · Aug 21, 2019#401
Yeah, I really like the 'idea' of the notch but was looking at things more closely and decided it wasn't a risk I wanted to take. Maybe if I go for the dual tip look down the road, I'll remove the rear bumper and properly build some notches with curved plastic and bondo for the recess; mould some nice cutouts, prime, spray and clear the bumper. However, for now, I just mounted the muffler as per the original pic. We supported the muffler with a jackstand and got it perfectly positioned so the tip I got will just barely touch the bumper. The only short 2.5" tip that I found that will work for me is 4" at the outlet. It should look good. It's due to arrive Friday, so when it's mounted, I'll post a pic.

Man, does the exhaust sound freakin' amazing now. The turbo muffler is deep and smooth at idle but sounds spectacular at 5500 rpm, and, zero drone at highway speeds.
06YarisRSThread starterFredericton, New Brunswick, Canada · Aug 21, 2019#402
Since Torque failed me in the A/FR and boost monitoring departments (AFR response times are way too slow and it won't show anything over vacuum), I'm having to completely redo my gauge setup. As mentioned, fortunately I had another driver's upper glove box cover in mint condition. My wife and kids are away for a few days, so I decided to be bad and do this on our kitchen table.

It looks very dirty and messy now, but will looked great when I'm done, fingers crossed. The AFR gauge is from a different series of Prosport gauges (the Premium Series) so there are differences. The ring color is a little darker and the gauge is taller. However, I think it will look great. My rationalization is that it's the most important gauge, so it will be a little more 'pronounced'. Then the other gauges (two on each side of the AFR gauge) will be symetrical. The face size, lettering and lighting color is precisely the same as all the other gauges.

My setup will be (from left to right): Oil Temp, Oil Pressure, AFR, Boost and Trans Temp.

Below is a pic in its current state. The gauges fit great and the gauge cups completely cover the holes. Each of the cups for the new gauges (AFR and Boost) will need to be profiled to fit the curvature of the glovebox, but I'm optimistic that I can get the to match seemlessly as the other 3 already installed gauges do.

Unfortunately, this is a LOT of work as the A-pillars and complete dash cover has to come off to attach the new glovebox cover. Plus, all of my wiring will have to be lengthened to move the existing gauges. Wiring and tubing has to be run for the AFR and boost and I'll have to drill a hole in the tunnel for the AFR O2 sensor wiring.

Picture not included in this copy

Yesterday, after a conversation with a gent at Booslang Manufacturing (the outfit that makes the Plug n' Play harnesses), I picked up a few 2.2K Ohm resistors. They put these in many of their Toyota harnesses on the crank and cam signal wires to combat noise that can cause studdering and possible idle problems associated with dirty signals and the AEM F/IC's sensitivity to such. Oddly enough I drove the car quite a bit today and neither would it studder (I have been manipulating the fuel table), nor would it stall or even buck at idle. I haven't installed the resistors yet. Maybe my ECU is starting to make its own adjustments.

Resistors

Picture not included in this copy
LeegamerAshland, VA · Aug 22, 2019#403
Gauge setup is going to be really cool, can't wait to see the finished product
06YarisRSThread starterFredericton, New Brunswick, Canada · Aug 22, 2019#404
Gauges continued

I still have a lot of work to do to contour, level and angle the gauge cups, but this should give a sense of the final look.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
LeegamerAshland, VA · Aug 22, 2019#405
I really dig that. Don't take this the wrong way, but it reminds me of a boat dash, but in a good way.
myfirstyotaToronto Canada · Aug 22, 2019#406
I've had this idea but with a smart phone and the torque app. But if it's not fast enough, I may just have to 'copy' your idea.
Looks great!
06YarisRSThread starterFredericton, New Brunswick, Canada · Aug 22, 2019#407
Originally Posted by Leegamer ↑
I really dig that. Don't take this the wrong way, but it reminds me of a boat dash, but in a good way.
Haha, come to think of it, it does look like a boat dash. Honestly, I'm not that fond of the overall look. Because of the design of the backside of the cover, I had to mount the gauges a little to the left. As such, they are not exactly lined up from the driver's perspective. I have a bit of leeway and may try to shift them all right a bit. Pics in next post.
06YarisRSThread starterFredericton, New Brunswick, Canada · Aug 22, 2019#408
Originally Posted by myfirstyota ↑
I've had this idea but with a smart phone and the torque app. But if it's not fast enough, I may just have to 'copy' your idea.
Looks great!
Yeah, I was very disappointed that Torque was useless for boost and AFR. I tried reducing the number of gauges - actually at one point down to just boost and AFR - and enabled fast communication. It was still useless.
06YarisRSThread starterFredericton, New Brunswick, Canada · Aug 22, 2019#409
5 Gauges cont'

Not thrilled with the look, but at least I will be able to accurately monitor all necessary parameters.

Just before install into dash

Picture not included in this copy

Fortunately, I didn't have to completely remove the dash cover. I could lift it enough to get at the screws behind.

Picture not included in this copy

Swapping springs over

Picture not included in this copy

Just a few pieces left to install: A pillars, center console etc. As mentioned in another post, I has to mount the gauges slightly left of center to get them all in. The back of the cover has an outward curve close to the center console that limits gauge placement somewhat. It would have placed the gauge at an odd angle. I have to crane my neck slightly to the right to see my oil temp gauge on the far left, but oil pressure, AFR and boost are prefectly in line. I get a weird sensation that I'm being stared at by large spider eyes. 😲

Picture not included in this copy

Picture not included in this copy
WeeYariGeorgetown, Ontario, Canada · Aug 22, 2019#410
Looks pretty darn good. Your Dremel just earned its keep.
ern-dizCA all day · Aug 22, 2019#411
Originally Posted by WeeYari ↑
Looks pretty darn good. Your Dremel just earned its keep.
^^^I was going to say.

Fine work.
06YarisRSThread starterFredericton, New Brunswick, Canada · Aug 22, 2019#412
Oh yeah! I picked up that dremel at a yard sale for $10.00 and it has been absolutely invaluable throughout this entire turbo project.

I'm glad you guys like the look. I'm sure it will grow on me once they're powered and lit up.

Tomorrow is the fun part - wiring that bloody AFR gauge. It's quite complicated with 4 harnesses, obviously the sensor and a control module. The boost gauge will be a snap as I'm tapping the vacuum line that feeds the F/IC MAF sensor which is behind the dash a foot or two away.
06YarisRSThread starterFredericton, New Brunswick, Canada · Aug 23, 2019#413
Gauges working

Just a few small details to finish up.

Hole drilled for wideband sensor. I had an old rear windshield wiper rubber grommet that worked great for the wideband sensor harness. Ill just pop it back out and apply a little rtv and smush it back in after the paint is fully cured. I painted the bare metal with primer and silver paint.

Picture not included in this copy

Running the two harnesses for the AFR gauge and the tubing for the boost gauge.

Picture not included in this copy

Harnesses and wideband control module. I have yet to permanently mount that. Getting crowded back there behind the glove box.

Picture not included in this copy

Beginning stages or wiring and 're-wiring'.

Picture not included in this copy

Day mode. The pics look horrendous. The gauges look some much more crisp, bright and uniform than my cell phone would have one believe. I still have to remove the clear plastic protectors on the gauges. Interestingly, the AFR gauge shows the same approximate readings that torque does at idle but it is so much faster responding, so much so that torque completely misses the subtle variations. I haven't driven it yet but I expect the differences between Torque and the wideband gauge will be significant.

Picture not included in this copy

I have to rotate a couple gauges to properly align them yet. Again the pics don't do the gauges justice. I'm sure the flash doesn't help. When I take pics without the flash, they come out very grainy.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Aug 26, 2019#414
New exhaust tip installed

I like the look, but wish I'd had the exhaust guy tilt the muffler a little closer to the bumper cover so the tip would be a tad closer. Still looks good, though, I think. I'll get an outdoor shot from a bit farther away. It was dark out when I took these.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
heeroyuy01195Florida · Aug 26, 2019#415
Looks fantastic!
06YarisRSThread starterFredericton, New Brunswick, Canada · Aug 27, 2019#416
Originally Posted by heeroyuy01195 ↑
Looks fantastic!
Thanks, dude! 👍

Some pics in next post. It's growing on me.
06YarisRSThread starterFredericton, New Brunswick, Canada · Aug 27, 2019#417
Tip Pics

I really have to get my "rule of thirds" down. Not much of a photographer. Lol.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Aug 31, 2019#418
Open Loop/Closed Loop Partial Throttle AFRs

The learning continues...

So, I'm seeing approximately stoich AFRs at partial throttle/low boost scenarios. When my throttle is close to maxed (I'll check my TPS via Torque to confirm when open loop kicks in - if in fact that's a variable that can, in and of itself, trigger open loop) I get perfect AFRs in the order of 12:1 or 11.5:1. I haven't noticed any ill effects whatsoever from the stoich AFRs at partial throttle low boost which I see for example if I'm slowly accelerating up a long hill at partial throttle. I actually wish I had and EGT gauge. Actually, Torque may have that option and maybe it can poll an EGT sensor in the car.

The F/IC does have an O2 spoofing function whereby voltages are manipulated to fool the ECU into thinking that a richer AFR is actually stoich, so in this respect closed loop AFR tuning is possible, I guess. At least that's how I think it works. Apparently there was no O2 map included in the F/IC tune that comes with the kit as they couldn't get it to function consistently across cars.

Currently, I am running 91 and sometimes 93 octane.

Any thoughts or observations regarding both my partial throttle/low boost AFRs and or O2 spoofing would be welcomed.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 9, 2019#419
After a bath and a good rip

I don't know if it's the weather (temp, humidity etc) or the car's ECU learning both fueling at idle and the new shift patterns, but the car is working great. The car hasn't stalled or even bucked at idle the last few times I've driven it. I drove around town and highway for a good hour after work and there were no stalls at stop lights, even idle and the shifting seems to have improved a lot. It's also starting on the first crank now. Before I might have to turn it over 2 or three times. I'm still getting some rich AFRs at light throttle deceleration and very light throttle (more like feathering the pedal) cruise, but oddly the ECU is commanding these AFRs. My 08 pretty much always commands 14.69, very infrequently 13s, but only for a split second.

Anyway, went for a good long drive tonight and entered full boost a half dozen times. The car pulls like crazy and shifts actually quite smoothly. After a good workout, coolant temps never exceeded 195, oil temps under 200, Trans temps around 180 - 190. It is cool out and the highest intake temp I saw tonight was around 80F. Very happy for now!

I still have to tighten my wastegate actuator arm but I'm hitting ~5.5 - 6 psi with the new kit in my BOV (Forge sent me a rebuild kit). Not sure if I really want or need the full 8.5 boost.

Crappy lighting + crappy camera = crappy pics...

Picture not included in this copy

Picture not included in this copy
tmontagueCaledonia Ont. · Sep 9, 2019#420
great to hear things are running smoother now. So was your BOV faulty?
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 9, 2019#421
Originally Posted by tmontague ↑
great to hear things are running smoother now. So was your BOV faulty?
Thanks. The car does seem to be running great and it's an absolute blast to drive.

Yeah, the BOV seemed to be bad. I applied equal pressure on both sides and it leaked. I did a rebuild on it but didn't actually test it before installing it.
LeegamerAshland, VA · Sep 10, 2019#422
So if you unplug your battery will you have to go through this whole learn process again?
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 10, 2019#423
Originally Posted by Leegamer ↑
So if you unplug your battery will you have to go through this whole learn process again?

That is indeed a good question and I'm purely speculating that the ECU is actually learning to adjust these variables. It may well be environmental factors. Regardless, I'm pleased that it's running well now. I've given up on the hope for stock-like around the clock reliability and consistency but I guess that's part of the equation when turboing a NA car. I have been driving it a lot lately with no issues, but am aware that things could change at any time. I'll keep the thread updated regarding the 'long term' functioning.
LeegamerAshland, VA · Sep 10, 2019#424
Originally Posted by 06YarisRS ↑
That is indeed a good question and I'm purely speculating that the ECU is actually learning to adjust these variables. It may well be environmental factors. Regardless, I'm pleased that it's running well now. I've given up on the hope for stock-like around the clock reliability and consistency but I guess that's part of the equation when turboing a NA car. I have been driving it a lot lately with no issues, but am aware that things could change at any time. I'll keep the thread updated regarding the 'long term' functioning.
Glad to hear it's running great now, though. Sorry, wasn't trying to be a "debbie downer"
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 10, 2019#425
Originally Posted by Leegamer ↑
Sorry, wasn't trying to be a "debbie downer"
Haha, I didn't take it that way at all, man. You posed a legitimate question about resetting the ECU and losing learned values, for sure. It's definitely something I thought about. See, great minds do think alike! Haha.
ern-dizCA all day · Sep 10, 2019#426
So cool to hear/see. The car looks great and I can only imagine how much more fun it is to drive over stock. Hopefully given enough time/data, you'll sort the remaining bugs, but it doesn't sound like they're all that bad.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 10, 2019#427
Originally Posted by ern-diz ↑
So cool to hear/see. The car looks great and I can only imagine how much more fun it is to drive over stock. Hopefully given enough time/data, you'll sort the remaining bugs, but it doesn't sound like they're all that bad.
Yeah, it's fun for sure. I went for a long highway drive this evening and tried out the cruise control. I did get the occasional buck and sweep of the AFR gauge under a certain load and rpm. I eliminated it with the addition of some fuel, but I'm going to solder in the 2.2K resistor because it's sounding a bit like the issue the Scion cars had. Enriching the fuel map cell helps but I think I may have a little glitch in the timing around 3500 and certain other factors associated with a dirty signal. All the Boomslang harnesses have the resistors wired in.

I decided to pull a second gear WOT acceleration this evening. I poured into the throttle at about 30 kmh and the front wheels- more likely 1 wheel - lit up and spun as it entered third gear. Third is the 'funnest' gear as it pulls very hard and long, relatively speaking. I did this pull as I wanted to observe the speedometer to ensure I'm not getting any clutch slippage. The speedo jumped rapidly with tach, so I think I'm good there. This thing would kill with an LSD. It accelerates very hard once it's up over 50 - 60 kmh. Below that it wants to spin like crazy at near full boost. Although the auto is doing quite well, expect it will eventually pack it in even though I wont often be driving like I described above. If/when it dies - or starts to fail - a manual with upgraded clutch will likely replace it. I'd really like a 6-speed.
WeeYariGeorgetown, Ontario, Canada · Sep 11, 2019#428
Would love to have my ass in the seat of that car.

Use your new found power responsibly and the tranny should serve you well.
CrankyOldManWest Michigan · Sep 11, 2019#429
Victory!
LeegamerAshland, VA · Sep 11, 2019#430
Originally Posted by WeeYari ↑
Would love to have my ass in the seat of that car.

Use your new found power responsibly and the tranny should serve you well.
Responsibility is overrated, lol
tmontagueCaledonia Ont. · Sep 11, 2019#431
Originally Posted by Leegamer ↑
Responsibility is overrated, lol
Bahah Yaris a/t's are cheap and easy to come by from a wreckers, I say go nuts!

FWIW you may want to swap out your trans fluid for a performance grade fluid like Amsoil or other. May give you some longer life from your trans should you grow an heavy foot!
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 11, 2019#432
Originally Posted by WeeYari ↑
Would love to have my ass in the seat of that car.

Use your new found power responsibly and the tranny should serve you well.
Visit the Maritimes and you can drive it yourself, WeeYari!
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 11, 2019#433
Originally Posted by CrankyOldMan ↑
Victory!
Yeeeaaahhhh!!! So far anyway. Lol.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 11, 2019#434
Originally Posted by CrankyOldMan ↑
Victory!
Originally Posted by Leegamer ↑
Responsibility is overrated, lol
It does dampen the fun a bit. Lol
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 11, 2019#435
Originally Posted by tmontague ↑
Bahah Yaris a/t's are cheap and easy to come by from a wreckers, I say go nuts!

FWIW you may want to swap out your trans fluid for a performance grade fluid like Amsoil or other. May give you some longer life from your trans should you grow an heavy foot!
That's the attitude. Lol. And, you're bang on about the trannies being cheap. I found one a while back on ebay that was from a wreck, something like 18000 miles on it for around $300.00 usd plus shipping.

I've always been an OEM trans fluid guy, especially after owning a Grand Caravan. It was ATF+4 or nothing. So, it's established that a good performance fluid would be perfectly compatible with the auto? Because, I would hands-down swap out the fluid for its superior properties if it was truly compatible in both the short and long term.
tmontagueCaledonia Ont. · Sep 11, 2019#436
Originally Posted by 06YarisRS ↑
That's the attitude. Lol. And, you're bang on about the trannies being cheap. I found one a while back on ebay that was from a wreck, something like 18000 miles on it for around $300.00 usd plus shipping.

I've always been an OEM trans fluid guy, especially after owning a Grand Caravan. It was ATF+4 or nothing. So, it's established that a good performance fluid would be perfectly compatible with the auto? Because, I would hands-down swap out the fluid for its superior properties if it was truly compatible in both the short and long term.
nothing wrong with OE fluids but your car is far from OE spec, not only with the bigger engine but the turbo as well. You likely will be fine with regular fluid changes as you have a cooler but I'm thinking more in the area of shear resistance from a better fluid.

OE spec fluid would meet sheer requirements the trans would face with the stock engine, in your case the clutches are working over time and I think a more sheer stable fluid would be some extra insurance. I have never heard of an issue with Toyota trans running Amsoil or even other fluid like Maxlife - they don't seem to be very sensitive to fluids as long as the fluid states it is compatible.

I personally always flush my used Toyota's with Maxlife simply because it is well priced and available locally to me. According to BITOG it is a pretty robust ATF and has always run well in my Toyota's (and Subaru's) that I have put a lot of mileage on. If I was in your situation I would likely go with an Amsoil product but it may be overkill. Just something to think about. If you are good with your fluid changes then you likely will never have to worry👍
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 12, 2019#437
Originally Posted by tmontague ↑
nothing wrong with OE fluids but your car is far from OE spec, not only with the bigger engine but the turbo as well. You likely will be fine with regular fluid changes as you have a cooler but I'm thinking more in the area of shear resistance from a better fluid.

OE spec fluid would meet sheer requirements the trans would face with the stock engine, in your case the clutches are working over time and I think a more sheer stable fluid would be some extra insurance. I have never heard of an issue with Toyota trans running Amsoil or even other fluid like Maxlife - they don't seem to be very sensitive to fluids as long as the fluid states it is compatible.

I personally always flush my used Toyota's with Maxlife simply because it is well priced and available locally to me. According to BITOG it is a pretty robust ATF and has always run well in my Toyota's (and Subaru's) that I have put a lot of mileage on. If I was in your situation I would likely go with an Amsoil product but it may be overkill. Just something to think about. If you are good with your fluid changes then you likely will never have to worry👍
Great info, Trevor. I'll definitely consider the use of a quality aftermarket fluid. The Amsoil might have a slight edge on the Valvoline product, but, like you say, maybe overkill. I plan to do some reading on the products. The fluid in my car is quite fresh. It's had a recent drain and fills and a couple more before that within the last 20 or 30K kms. I've also been considering the purchase of a performance valve body. It might be a very good first upgrade and one that should be fairly easy as it could be done without the need to drop the trans. Going to do some more reading on that too.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 18, 2019#438
Tune and oil filters (random)

I haven't been completely happy with the tune from the tuner. Yesterday I was getting some erratic AFRs and a bit of bucking at "high speed" cruise. I call high speed cruise around 130 - 140 km/h. I decided to upload the basemap to the FIC and give it a run. The car worked much better. I did have a very slight buck at around 120 km/h on a slight incline at part throttle. This time though, it went rich and bogged. So, I leaned it out a bit and then drove for a good hour up and down hills, different speeds and it worked great. AFRs remained reasonable steady and I'm getting 11.5:1 at WOT. I still have to install the 2.2K ohm resistor on the crank signal wire and hope to do that this weekend.

Oil and oil filters.

Walmart USA has SuperTech Full Syn on at $14.97 a jug. I have to take my daughter to events in St. Stephen next to the border two nights a week. I have an hour to kill, so I go across each time and grab a jug and a filter each time. Being a cheapskate and all, I avoid duty this way. I also get to fill up with Shell V-Power 93 while I'm there.

Just for fun, for you 2ZR folks, which filter would you buy and why? The SuperTech is $2.97, the Fram and the K&N are ~ $4.50 each. If you tell me your choice and reasoning, I'll tell you which one I bought and why. 👏 Play along if you're bored.

Picture not included in this copy
CrankyOldManWest Michigan · Sep 19, 2019#439
Originally Posted by 06YarisRS ↑
Just for fun, for you 2ZR folks, which filter would you buy and why? The SuperTech is $2.97, the Fram and the K&N are ~ $4.50 each. If you tell me your choice and reasoning, I'll tell you which one I bought and why. 👏 Play along if you're bored.
Doesn't answer your question but I have several Toyotas and it just made sense for me to swap the cartridge setup for the traditional can style. Now all of my 'Yotas use the same one. The Vibe is possibly going to get the swap as well since it's also a 2ZR.
myfirstyotaToronto Canada · Sep 19, 2019#440
I just use Toyota filters. Gotta be good enough right?

I have used the fram filters on the beater before. Sometimes I just can't get to the dealer with their hours and my work schedule. I've never noticed anything horrible about them like a lot of people say. 340,000km and still purrs like a kitten.
thebarberGrand Rapids, MI · Sep 19, 2019#441
sexy outcome (all of it)
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 19, 2019#442
Originally Posted by CrankyOldMan ↑
Doesn't answer your question but I have several Toyotas and it just made sense for me to swap the cartridge setup for the traditional can style. Now all of my 'Yotas use the same one. The Vibe is possibly going to get the swap as well since it's also a 2ZR.
Yes, I've definitely been considering switching to the screw on can setup. I think the adapter is around $80.00 USD plus shipping. Probably $500.00 at the local dealer. Afterall, they wanted close to $500.00 for a vehicle speed sensor. 😲
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 19, 2019#443
Originally Posted by myfirstyota ↑
I just use Toyota filters. Gotta be good enough right?

I have used the fram filters on the beater before. Sometimes I just can't get to the dealer with their hours and my work schedule. I've never noticed anything horrible about them like a lot of people say. 340,000km and still purrs like a kitten.
Damn straight about Toyota filters.

I used Fram all throughout my early automotive years, long before I'd heard about the unsubstanitated "orange can of death" lore. Never had one single issue, cardboard end caps or not, and I often had very long OCIs.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 19, 2019#444
Originally Posted by thebarber ↑
sexy outcome (all of it)
Oooh yeah! So, who bought the Blitz? Just kidding/respecting privacy. Though, hopefully whomever did will make it known! Haha
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 19, 2019#445
Originally Posted by 06YarisRS ↑

Just for fun, for you 2ZR folks, which filter would you buy and why? The SuperTech is $2.97, the Fram and the K&N are ~ $4.50 each. If you tell me your choice and reasoning, I'll tell you which one I bought and why. 👏 Play along if you're bored.

Picture not included in this copy
I feel a little silly quoting myself, but I went for the K&N, not because I'm a big fan, but because it had seemingly the largest surface area, although very close to the Fram, and it's supposed to be very high flow media. With the turbo, I'd like the most oil possible pumping through the system. I've heard good things about the SuperTech filters and wouldn't normally hesitate to use one, but it looks like it might be a little restrictive given how much of the media the end caps cover.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 28, 2019#446
Some positive developments

I always hate to say that something is definitively fixed. Or, that I've finally solved something or other, as I've learned that with these types of extreme modifications, there are really no 'for sures' or 'finallys'

But, I installed the 2.2 K Ohm resistor between crank mag + and -. Scions and Toyota's using the AEM F/IC often suffer from a dirty crank and cam sensor signal that freaks the F/IC out and it messes with (probably pulls) timing resulting in bucking at part throttle under low boost, or in the transition between boost and vacuum, I believe. In many cases these dirty signals have been known to mess with the idle as well.

I have driven the car for a good hour and a half and have zero bucking. I will qualify this by saying that I didn't get out on the highway where I was experiencing some bucking at around 130 km/h at a certain load. However, the slight bucking that I experienced at lower speeds and loads is gone (for now). Tomorrow I will get out on the highway and test. I may have to re adjust my fuel table as I made changes before the resistor install.

Idle: after 1.5 hours driving, sitting and idling (for numerous periods of time) in park, neutral and in gear with every accessory turned on, I experienced not one buck or idle fluctuation. Once the car hits operating temp it settles down at idle to around 600 rpm and is rock steady. The car also starts as soon as the ignition is turned.

Anyway, it looks good, but, again, I'm not holding by breath.

resistor soldered in

Picture not included in this copy

A Torque bonus

I was scanning through the available sensors and hadn't noticed before that an available PID is B1S1 CAT Temp and B1S2 CAT Temp. This is awesome as I can get a fair sense of my EGTs. The middle 2 gauges are B1S1 CAT Temp (top) and B1S2 CAT Temp (bottom). This is a great find. In this pic, the downstream 02 sensor hadn't reached operating temps so the voltage remained at 0.1V. As soon as I drove a bit, it came to life. I had been getting the occasional P0420 (Catalyst Inefficiency) code but I think it was due to the car bucking, going extremely lean and/or extremely rich under different conditions, shooting the 02 sensor voltage out of range. I will run the car for a bit and if the code returns, I'll just add a spark plug defouler, pulling the 02 sensor a back a touch out of the exhaust stream.

Anyway, at idle, I'm getting around 800 F EGT, around 1000 at cruise and after several good, but short boost sessions, I reached a max of around 1200 - 1300F. Keeping in mind that the temp is being taken after the turbo which I've read can be a couple hundred degrees cooler. So, that still seems good, not too high. Apparently many aftermarket EGT gauges start their redline around 1600F.

Picture not included in this copy

Car idling great

Picture not included in this copy
tmontagueCaledonia Ont. · Sep 28, 2019#447
Excellent to hear, I hope it stays this way.

FWIW I monitored O2 sensor temp last year using my ultra gauge, I don't remember if it was s1 or s2 but it read between 1000F and 1400F+ if I really got on it.

Be careful about using a spark plug defoulders with the p0420. I tried that on my 3.6R subie and I ended up eventually triggering 2 or 3 other O2 codes due to voltage and slow response time - although the original p0420 never came back during the defoulder install. I also confirmed via fuel trims that is was messing with the fueling a bit.

I remember you mentioning the secondary O2 sensors in newer cars actually having an effect on fueling and looks like you were bang on. You can use O2 sensor voltage to diagnose if it is in fact a bad catylitic converter or not via watching its waveform or just careful monitoring of its voltage while on quiet back roads.

How exactly does the resistor work? I'm curious based on how it is wired in, what does it actually do to the wires.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 29, 2019#448
Originally Posted by tmontague ↑
Excellent to hear, I hope it stays this way.

FWIW I monitored O2 sensor temp last year using my ultra gauge, I don't remember if it was s1 or s2 but it read between 1000F and 1400F+ if I really got on it.

Be careful about using a spark plug defoulders with the p0420. I tried that on my 3.6R subie and I ended up eventually triggering 2 or 3 other O2 codes due to voltage and slow response time - although the original p0420 never came back during the defoulder install. I also confirmed via fuel trims that is was messing with the fueling a bit.

I remember you mentioning the secondary O2 sensors in newer cars actually having an effect on fueling and looks like you were bang on. You can use O2 sensor voltage to diagnose if it is in fact a bad catylitic converter or not via watching its waveform or just careful monitoring of its voltage while on quiet back roads.

How exactly does the resistor work? I'm curious based on how it is wired in, what does it actually do to the wires.
Yeah, I hope it keeps working well. I'll know a bit later today as I'll be going for a good highway run.

EGTs:

I did some more reading on EGTs vs 02 sensors for monitoring data on temps. Most of what's available on the net regarding EGTs is referring to diesels. However, it is commonly accepted that EGTs should be monitored pre turbo (in the exhaust manifold). A portion (probably a significant amount) of the heat from the exhaust manifold is converted into mechanical energy spinning the turbine. This would account for a lower reading post turbo. I did take my 2008 (completely stock) Yaris out and monitored the CAT B1S1 temps as a comparison. I didn't see any significant temp differences between the two cars. Both were somewhere around 1000 when cruising and around 1300 - 1350 ish when being driven moderately to hard. This makes me feel a bit better as actual EGTs should be within specification even given the different AFRs (stock vs turbo tuned). Then again, maybe my EGTs are actually higher in the turbo car as the stock Yaris's 02 sensor is closer to the manifold and doesn't have a turbo infront of it. As an indirect comparison, the CAT temps on my Kia Sedona run as high as 1500s - 1600s and have ever since owning it. It's never had any issues. I am not ruling out the installation of an actual EGT sensor and gauge. Nor am I ruling out water or water/meth injection or a an intercooler misting system. That said, my intake temps are quite low and I never plan on going full boost immediately after sitting in bumper to bumper traffic in the summer. I'm also running Shell V-Power 93 and a fairly low boost. And, although I do go into boost fairly often, it is rarely sustained for longer than 7 - 8 seconds. I'm no engineer but even though EGTs can spike quickly, I think the actual head, pistons, valves etc would require a little more time to get hot enough to melt. I plan to do a bit of reading on heat soak and EGTs. Another thing I'm going to look into is moving my intake a bit lower and possibly toward or into the area in front of the wheel well a bit.

Defoulers:

Yes, installing a defouler may well adversely affect AFRs. I would start by installing only one as opposed to two. Before I did the swap or turbo, I had a code, I think it was the P0420 as a local mechanic removed my primary CAT. I installed the defoulers and ran that right up until the swap with no codes or adverse effects. Even if I do try this and it messes a bit with AFRs, I expect that my ECU will be able to compensate by adjusting trims. Some day, I'm going to tackle the 02 spoofing feature of the F/IC. I can adjust voltages tricking the ECU to target a non-stoich AFR without knowing it. I guess they had limited success with this though across a number of applications at turbokits.com. Doesn't mean I won't try it eventually though. I'd sure love to have more control of fueling in closed loop. I was looking at the Haltech ECUs again and they offer closed loop fueling, but they are standalones, so god knows what other issues I might run into with such things as DBW and peripherals.

Resistor:

I don't really understand how it works wired that way as I'm very weak knowledge-wise in the electrical department. The best explanaton I could find is from a post by member Vitigo on scionlife. He says, "... to pull down the voltage I need to connect the resistor to ground. thats why you guys do on you tc is that, connect the resistor to the + to - so you can pull down the voltage on the + side."
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 30, 2019#449
A Real Buck Fest... 😲

I did my highway drive today and it was like riding a bucking bronco at around 130Km/h with wild AFR swings under moderate throttle, accelerating. I had made fuel changes to the base map that comes with the kit before I installed the resistor. Figuring that these changes were adversely interacting with the resistor install (timing), I uploaded a fresh copy of the F/IC cal. file. I had some very minor bucking at a specific area of the fuel map. But this time I tried something different. Rather than tweaking the fuel map using AFRs, I used fuel trims data. When the bucking occured, I would see the ECU pull 20 - 25% fuel. It was going extremely rich causing the car to bog. When it jumped to an adjacent fuel cell, it would go stoich or slightly lean and the ECU would dump fuel in. This is what was causing the wild AFR swings. I found a long hill, set my cruise control so that I could maintain the load and rpm where the bucking was happening and the trims showed fuel being pulled. I pulled a tiny bit of fuel from those cells and, bingo, fuel trims stabilized. I kept working the map and in almost all sections of the fuel map, now, I rarely see more that 2 - 3% short term fuel trim correction and it's often at 0.0%. It is a significant understatement to say that miniscule adjustments in the fuel map produce massive changes in AFR! Tenth's of a percent can radically affect fuel ratios, it seems. I had no idea it was that sensitive. I can only imagine how much work it was to create that basemap in the first place. Of course, those guys aren't starting from zero in the knowledge department like I am. I am beginning to wonder if there are slight differences in the fueling strategies between the Corolla (for which this kit and base map were developed) and the Scion xD ECU which might account for the tune/performance abnormalities.

So, for now, I have no idle stalling (prefect idle, under full accessory and gear load or no load in neutral or park) and no bucking at any highway speeds/loads. Fingers crossed that these settings stay and that the car continues to drive smoothly. I did a good hour or two driving under all conditions and it was like driving a stock car, except with a heck of a lot more power. 👍 If things start to go awry, I am going to do more reading on standalone ECUs, O2 sensor spoofing or removing my wideband O2 sensor and going full open loop, custom maps (if it's possible) with this car.

I still have to tighten my wastegate flapper and try to ring another 2 - 2.5 psi out of the turbo. I'm waiting until my fender liner arrives to jack the car up. When I reinstalled the lower engine covers, I was in a hurry and missed attaching the front of the wheel well liner and burned a hole through it on the highway. It was definitely a panic moment as I heard this awful scraping sound and started to smell burning plastic. I was pretty relieved to see that it was just the wheel well liner.
ern-dizCA all day · Sep 30, 2019#450
Sooo interesting to read/learn about.