ArmstrongRacingOriginal postSan Diego · Jan 13, 2016#1...And so it begins. The 1.8L dual vvt-i 2zr-fe is a relatively new engine, released in 2007. This engine produces 136hp/129ftlbs at the crank in stock form, and is a smog legal swap when done properly. There is great aftermarket support with people making 150hp n/a with flow mods, or 200hp+ with available superchargers and turbo kits. I chose to get my swap components from a auto recycler instead of buying a scion xd. My engine is from a 2013 Corolla with 34k on the odometer(the valve cover writing is wrong)...a great find. My car is automatic and Ive kept the auto for now to check compatibility. Lets start, here's whats needed:
1)2ZRFE engine with ALL components and accessories from a 2009+ Xd, Corolla
2)ECM from a 2008-2009 Xd applicable to your car in auto or manual trans
3)Xd engine harness also applicable to your car and transmission choice.
4)Xd RH and LH engine/transmission mount and brackets
5)Xd exhaust midpipe
6)Xd intake AND MAF sensor
7)Xd or Corolla flex plate(auto), flywheel/clutch(manual)
8)Mini-add-a-circuit and soldering equipment
*With the help of other YW members, I have started a collection of 2ZRFE parts to make everyones swap a little easier, just contact me for details!*
Read through the entire thread to learn as much as possible before beginning. Good luck!
1 attachment not included in this copy
Replies 413
ArmstrongRacingThread starterSan Diego · Jan 13, 2016#2If you go through a recycler you need to prepare yourself to make a ton of phone calls and be clear about what you need and how you want it. Expect to spend roughly $3000 total for everything needed. You can also buy a entire wrecked car if you like, but it will cost you more. You want everything that was originally attached to the engine, including ecm, exhaust, airbox(xd), passenger engine mount(xd), ect. Ill cover all of this throughout my install.
1 attachment not included in this copy
ArmstrongRacingThread starterSan Diego · Jan 13, 2016#3The first thing I checked was compatibility with the yaris c50 transmission. The 2zr and 1nz flywheels/Flexplates are the same size, the only difference is the 2zr has 8 bolts where the 1nz has 6.....so use the 2zr flywheel and your 1nz clutch.
1 attachment not included in this copy
ArmstrongRacingThread starterSan Diego · Jan 13, 2016#4The bell housing flanges on the 2zr and 1nz are also the same, both are a 9bolt 2-o'clock starter orientation. Apply a little grease to the dowels, and you can use the 1nz starter.
1 attachment not included in this copy
Bluevitz-rsOshawa, Ontario, Canada · Jan 14, 2016#5👍
tmontagueCaledonia Ont. · Jan 14, 2016#6Aaaamazing
thebarberGrand Rapids, MI · Jan 14, 2016#7much winning
3cyltrboOttawa · Jan 14, 2016#8Armstrong Racing for President !
MedMantleSouth Africa · Jan 14, 2016#9So stoked that it is finally happening! Gonna dump my 1JZ Cressi swap plans and rather invest my time and money in this! Whack damn son!
fredovvtiSabana Grande, PR · Jan 14, 2016#10Yuppiii!! 👍👍👍
LTHatchNewark NJ · Jan 14, 2016#11Awesome! Great information.
ArmstrongRacingThread starterSan Diego · Jan 14, 2016#12I ordered the xd airbox, engine mount, and maintenance items today. They should be in tomorrow, now I just gotta get an ecm and start the wiring.
CrankyOldManWest Michigan · Jan 14, 2016#13 Originally Posted by
ArmstrongRacing ↑ I ordered the xd airbox, engine mount, and maintenance items today. They should be in tomorrow, now I just gotta get an ecm and start the wiring.
I can help with the wiring diagrams if you have to modify anything--I just snagged copies of every year xD and Yaris that I could find on the Toyota tech site.
On a format note: I'm not sure if the file size is the reason for only one picture per post, but it would be much more helpful to have the whole process in the first few posts instead of having to sort through lots of replies to find the content.
ArmstrongRacingThread starterSan Diego · Jan 14, 2016#14My plan was to document each step carefully with one picture for each step. Yes there will be replies to read through, but some of those comments could be good information in case there are questions.
Bluevitz-rsOshawa, Ontario, Canada · Jan 14, 2016#15 Originally Posted by
ArmstrongRacing ↑ My plan was to document each step carefully with one picture for each step. Yes there will be replies to read through, but some of those comments could be good information in case there are questions.
Can't you just edit the last post and keep adding to it. Upload the pictures to photobucket.com and link the pictures. You can add as many as you want to that way.
Sent from my iPod Touch
ArmstrongRacingThread starterSan Diego · Jan 15, 2016#16I went through the wiring diagrams today and verified the 2zr ECM(automatic transmission) and harness are mostly plug-n-play with the Yaris U340E. For you guys using a manual transmission, you need a manual trans specific harness and ECM.
1 attachment not included in this copy
beakerconyers ga · Jan 15, 2016#17 Originally Posted by
ArmstrongRacing ↑ I went through the wiring diagrams today and verified the 2zr ECM(automatic transmission) and harness are plug-n-play with the Yaris U340E. For you guys using a manual transmission, you need a manual trans specific harness and ECM.
Could you clarify a little more on this? What do you mean by U340E?
One of my other concerns is emissions. When you swap to a different car ECM, I'm wondering what kinda of problems that will create when one goes for their annual emissions testing? Doesn't the computer store the VIN info, and I wonder if it will throw a red flag when the emissions testing machine is hooked up to your car, and the VIN #s don't jive?
tmontagueCaledonia Ont. · Jan 15, 2016#18Hmm, that is my only concern w/ emissions. I know here in Ontario they care solely on the obd scan and making sure that they're are no codes but i'm not sure if they check to see if the ecu matches the Vin on the car
CrankyOldManWest Michigan · Jan 15, 2016#19 Originally Posted by ArmstrongRacing
I went through the wiring diagrams today and verified the 2zr ECM(automatic transmission) and harness are plug-n-play with the Yaris U340E. For you guys using a manual transmission, you need a manual trans specific harness and ECM.
Good to know. I found that the Yaris ECU pinout is not compatible with the xD wire harness on either connector. Have you addressed the issues with the smaller connector on the ECU, since some of it goes into the interior? What about the end of the engine wire harness that goes into the engine bay relay/fuse box?
**EDIT**
Here's my
spreadsheet for comparing the pinouts of the Yaris and xD ECU connectors. I will have to look at the EWDs again when I get home at the end of the month to see what the missing/conflicting names go to. Hopefully that connector just needs to be pin swapped.
ArmstrongRacingThread starterSan Diego · Jan 15, 2016#20The U340E is the automatic transmission in all yaris'. The 2zr harness has the exact same transmission plugs with the same wire locations.
The BAR station that inspects your car after completing the swap will give you a label to signify your swap is legal, the different VIN in the ECM is ok, the requirement is the cats have to be there, a legal intake, and no check engine light.
beakerconyers ga · Jan 15, 2016#21 Originally Posted by
ArmstrongRacing ↑ The U340E is the automatic transmission in all yaris'. The 2zr harness has the exact same transmission plugs with the same wire locations.
The BAR station that inspects your car after completing the swap will give you a label to signify your swap is legal, the different VIN in the ECM is ok, the requirement is the cats have to be there, a legal intake, and no check engine light.
OK cool, thanks for the info on what U340E meant.
I've got to go this weekend to get emissions done on my cars, my birthday is coming up, so got to get tags. I've got a buddy who I go to for emissions testing, I'll propose that question to him, to see if that's how it's done here in GA.
ArmstrongRacingThread starterSan Diego · Jan 15, 2016#22Here is the xd engine mount PN#12305-37091....the associated bracket on the engine timing cover also has to be from a xd PN#12315-37040. You will also need the 2 bolts PN#91552-L1240, stud, and 2 nuts that attach the mount to the bracket. My engine came with the Corolla bracket and I wanted to test fit with it......it does not work.
Also you will notice the Corolla ECM back there. Ive already completed a swap with all of the xd electronics, this time Im testing Corolla parts. The Corolla wire harness and ECM will Terminate to the battery area, whereas the xd wire harness and ECM are run like the 1nz. I ran my Corolla harness over to the original ECM location and secured with zip ties until I know everything works.
UPDATE: THE 2010+ COROLLA ECM IS NOT COMPATIBLE UNLESS YOU PLAN ON PROGRAMING NEW KEYS. I had to order a Scion Xd ECM because my car doesn't have immobilizer. For automatic transmissions the part # is 89661-52F71.
1 attachment not included in this copy
ArmstrongRacingThread starterSan Diego · Jan 15, 2016#23This is a 2zr exhaust gasket against the 1nz collector, you can see there is a huge difference in size and this collector will need modifications to work. The bolt spacing on the 2zr exhaust manifold is also larger, its best to find a xd midpipe or collector and have the rest done at a exhaust shop.
1 attachment not included in this copy
ArmstrongRacingThread starterSan Diego · Jan 15, 2016#24Here is a xd airbox with the required 2zr MAF sensor. I got these items from Ebay, if you are not concerned about emissions then you can buy a aftermarket intake for an xd.
1 attachment not included in this copy
ArmstrongRacingThread starterSan Diego · Jan 18, 2016#25When you are ready to install the powertrain, remove this mount and bracket. The larger engine will not give you enough room to properly line up these mounts while mounted to the trans. Slide everything into place then install this mount last.
1 attachment not included in this copy
ezhacker1San Francisco · Jan 18, 2016#26I love these posts. reliving those moments at the storage shed swap. :)
ArmstrongRacingThread starterSan Diego · Jan 18, 2016#27Once the powertrain is in and all of the mounts, suspension, and axles are secure....you can start installing your original hoses and lines. The heater hoses will need 2" trimmed off of the engine side, the fuel line will need to be flipped around and installed backwards(or buy one for an Xd), but the remaining brake booster, radiator hoses, and evap solenoid hose can be installed how they were originally.
1 attachment not included in this copy
ArmstrongRacingThread starterSan Diego · Jan 18, 2016#28Now you can assemble the rest of the car and it will look like this. If your car has a/c you will also need the compressor lines: Pn#88712-52341,88711-52311...then get your a/c system recharged. Next step....wiring.
1 attachment not included in this copy
3cyltrboOttawa · Jan 19, 2016#29SOOOOO much WIN!
beakerconyers ga · Jan 19, 2016#30Did you use XD axles, or Yaris axles?
beakerconyers ga · Jan 19, 2016#31 Originally Posted by
beaker ↑ Could you clarify a little more on this? What do you mean by U340E?
One of my other concerns is emissions. When you swap to a different car ECM, I'm wondering what kinda of problems that will create when one goes for their annual emissions testing? Doesn't the computer store the VIN info, and I wonder if it will throw a red flag when the emissions testing machine is hooked up to your car, and the VIN #s don't jive?
For those interested in the emissions question, I did some asking around and a little research at
www.cleanairforce.com, which is the state of Georgia's website for emissions standards. It appears, or at least in my case, if you put an engine in a car that was never put in that said car for USA production, and that car falls under emissions standards, it then becomes what is called a "grey market vehicle." I have been told, but have not verified, that it is possible to get a "emissions waiver" from the state, if it can be demonstrated that your car will still pass emissions standards for your year make and model of car. I say that I haven't verified this, because what I found on the website is kinda vague, and this info came from the emissions inspector that recently had tested my car. I would definitely want to confirm with the state, that what he said is in fact the case. The emissions inspector did say that by putting a different ECM in my car( IE from a Scion XD), would throw a read flag, because the info coming out of the ECM would not jive with the car being tested, so it would fail without the waiver. Not sure if this info would apply the same to others in different states, but IMO, it would be something I would check on before doing the swap and spending the money.
I'm truly not trying to be a buzzkill, because this swap is AWESOME, and I really want to do this to my car. Just something to think about and investigate if your car is required to meet state emissions standards.
ArmstrongRacingThread starterSan Diego · Jan 19, 2016#32 Originally Posted by
beaker ↑ Did you use XD axles, or Yaris axles?
Yaris transmission and axles on my car, Xd transmission and axles on another.....its up to you.
And about emissions, everyone should check their own states laws before starting any swap. I already have permission from California to do this swap, I called in advance.
fnkngrvIn The Hotbox · Jan 19, 2016#33As a side note do you know how much beefier the xD axles are if any?
Sent from m-o-b-i-l-e
CrankyOldManWest Michigan · Jan 19, 2016#34 Originally Posted by
fnkngrv ↑ As a side note do you know how much beefier the xD axles are if any?
Thread hijack! =)
For reference, the Yaris uses 23 tooth 24/48 DP stubs, the xD (Celica/Matrix/Corolla) uses 20 tooth 20/40 DP stubs. I'm drawing a blank on how to calculate the actual diameter. The Quaife datasheets show the inner diameter of the xD differential inputs as 28mm, the Yaris as 27mm.
**Edit**
Some quick math with a gear/spline theory worksheet gives an outer diameter of 1.041" on the Yaris splines, 1.1" on the xD. No idea how big the shafts are past that, but a trip to the junk yard with some calipers would tell you.
ArmstrongRacingThread starterSan Diego · Jan 19, 2016#35Like Cranky said....visually they are also just a little bigger.
Like my Corolla exhaust....the ID is 46mm, Yaris is 40mm
fnkngrvIn The Hotbox · Jan 19, 2016#36Good to know. Could play a part in how people look at the swap for auto x, etc especially if they boosted it.
Sent from m-o-b-i-l-e
3cyltrboOttawa · Jan 19, 2016#37 Originally Posted by
ArmstrongRacing ↑
And about emissions, everyone should check their own states laws before starting any swap. I already have permission from California to do this swap, I called in advance.
+1
Up here in Canadia (aka Canada), it varies from Province to Province and even different municipalities.
Where I live, I've never heard or seen of someone ever getting a ticket related to emissions / engine swaps etc....
And our emissions testing has moved away from sniffer tests (at least in my area) and now focuses solely on Check Engine Lights.
Personally If I go through with this swap, of a Toyota engine into a Toyota and one that will look like it belongs there, emissions and "Fix it Tickets" will be the farthest thing from my mind.
ArmstrongRacingThread starterSan Diego · Jan 20, 2016#38 Originally Posted by
fnkngrv ↑ Good to know. Could play a part in how people look at the swap for auto x, etc especially if they boosted it.
I agree the bigger differential and axles would add a bit of assurance, but the gearsets are still the same parts from the yaris C50. I personally know 6 guys racing with the Yaris trans and no issues. The Yaris is a stout little car, power is its only downside.
CrankyOldManWest Michigan · Jan 20, 2016#39 Originally Posted by
ArmstrongRacing ↑ I agree the bigger differential and axles would add a bit of assurance, but the gearsets are still the same parts from the yaris C50. I personally know 6 guys racing with the Yaris trans and no issues. The Yaris is a stout little car, power is its only downside.
As long as you're in the 150 hp range, you should be OK with the Yaris diff and drive shafts. If you plan on going into the 150-250 bhp range, I would recommend (without empirical evidence) going with the xD setup, if only because it is standard on vehicles with 150-200 stock bhp. Anything over 250 bhp will probably need custom shafts for longevity.
From a price standpoint, xD aftermarket diffs are normally cheaper than the Yaris, since it has more demand. For example, the Quaife QDF15E (Yaris) costs around $1100, whereas the QDF21E (xD/Celica/etc.) is normally under $1000. Keep in mind that the ring gear on the differential is NOT compatible between these two models, but the xD differential will potentially open up more options for final drive ratios--and potentially at a lower cost than the Yaris.
But enough talk about drive shafts. Let's get to that wiring! =)
tmontagueCaledonia Ont. · Jan 20, 2016#40 Originally Posted by
3cyltrbo ↑ +1
Up here in Canadia (aka Canada), it varies from Province to Province and even different municipalities.
Where I live, I've never heard or seen of someone ever getting a ticket related to emissions / engine swaps etc....
And our emissions testing has moved away from sniffer tests (at least in my area) and now focuses solely on Check Engine Lights.
Personally If I go through with this swap, of a Toyota engine into a Toyota and one that will look like it belongs there, emissions and "Fix it Tickets" will be the farthest thing from my mind.
The only thing you'd have to check with in Ontario is that I'm pretty sure they check to see if the ECU is giving off the correct vin that is on the body of the car. If not that may mean an instant failure of the e test. I'm sure you could easily get a waiver but I'd check into it before you do your swap. Let me know what the result is
ilikericesavannah, ga · Jan 20, 2016#41Wiring.. everyone's favorite part... RIGHT!
Looking good Armstrong!
CrankyOldManWest Michigan · Jan 20, 2016#42Just a friendly reminder, if you have to replace the exhaust anyway, you should consider the
xD long tube header from Fast Scions. I've got a mandrel bent 2.5" res-back kit that would be a great start on a mid-pipe for this. =)
RigaudRigaud, Quebec, Can. · Jan 20, 2016#43 Originally Posted by
3cyltrbo ↑ +1
Up here in Canadia (aka Canada), it varies from Province to Province and even different municipalities.
Where I live, I've never heard or seen of someone ever getting a ticket related to emissions / engine swaps etc....
And our emissions testing has moved away from sniffer tests (at least in my area) and now focuses solely on Check Engine Lights.
Personally If I go through with this swap, of a Toyota engine into a Toyota and one that will look like it belongs there, emissions and "Fix it Tickets" will be the farthest thing from my mind.
No municipality has a say in emissions in Canada. Regulated by Federal then Provincial.
RigaudRigaud, Quebec, Can. · Jan 20, 2016#44 Originally Posted by
tmontague ↑ The only thing you'd have to check with in Ontario is that I'm pretty sure they check to see if the ECU is giving off the correct vin that is on the body of the car. If not that may mean an instant failure of the e test. I'm sure you could easily get a waiver but I'd check into it before you do your swap. Let me know what the result is
No, you can replace the ECU...hence replacing it when it fails!!! Sniff test that's it via OBD. They check if theirs been any cel that popped up recently. Straight forward. My friend nearby in Kawkesbury just went through it with his Audi URS4.
tmontagueCaledonia Ont. · Jan 20, 2016#45so they don't check if the OBD is giving off the matching VIN to the body of the car? I thought if you end up installing a new ECU because the stock one was dmaaged then the dealership reprograms it to match the VIN of your car?
If that is the case then ya it'd be no issue.
ArmstrongRacingThread starterSan Diego · Jan 20, 2016#46If you were lucky enough to source a Xd engine harness, the plugs on the fusebox end are a direct match and the only wiring changes needed invole the speed sensor and MAF sensor.
CA2- top left
CA1- top right
1 attachment not included in this copy
ArmstrongRacingThread starterSan Diego · Jan 20, 2016#47Here are the highlighted pins that need swapping.
1) If you keep the Yaris transmission: Move the speed sensor wires over to the same spots in the Xd plug CA2.
1a) If you use the Xd transmission, your car better have ABS to steal the speed signal from....those are the only options I know of at this time regarding speed signals.
2) The MAF sensor power wire at CA2#9 has no supporting pin in the Yaris fusebox. I tried removing this wire from the plug and soldering it to another +12v wire in the fuse box...but the MAF voltage would fluctuate. My final fix was to cut the power wire 8" from the MAF plug and run a dedicated power wire via a mini-add-a-circuit in a IG switched fuse location.
1 attachment not included in this copy
ArmstrongRacingThread starterSan Diego · Jan 20, 2016#48If you couldn't locate a Xd harness than your swap(like mine) is going to be much more involved wiring wise...
The Corolla harness has 3 plugs on the fusebox end and none of them match the yaris. You must move every single wire to its corresponding location in the yaris' CA1 and CA2 plugs.(I'm almost done). In addition to re-pinning, you will also have to cut the 2zr harness battery cables going to the starter/alternator and connect them to your 1nz harness cables for the extra length and the proper ends....lots of work.
NOTE: You can see my mini add-a-circuit for the MAF here
1 attachment not included in this copy
beakerconyers ga · Jan 21, 2016#49 Originally Posted by
ArmstrongRacing ↑ Here are the highlighted pins that need swapping.
1) If you keep the Yaris transmission: Move the speed sensor wires over to the same spots in the Xd plug CA2.
1a) If you use the Xd transmission, your car better have ABS to steal the speed signal from....those are the only options I know of at this time regarding speed signals.
2) The MAF sensor power wire at CA2#9 has no supporting pin in the Yaris fusebox. I tried removing this wire from the plug and soldering it to another +12v wire in the fuse box...but the MAF voltage would fluctuate. My final fix was to cut the power wire 8" from the MAF plug and run a dedicated power wire via a mini-add-a-circuit in a IG switched fuse location.
So the MAF (CA2#9) needs to see +12volts with ignition on? It's not a signal coming out of the MAF with variable voltage output going back into the ECM?
ilikericesavannah, ga · Jan 21, 2016#50I understand what your saying but can I suggest a bit of rewording... Try to do a step by step process in 1 post for the wiring with what you have acquired (yaris harness and yaris Trans).
-Then have a separate post if you use the yaris harness with xD trans,
-another post for yaris trans with the xD harness,
-and another post for the xD harness and xD trans.
After that is done, if you could go ahead and mention corolla parts.
You are mixing scenario's up in 2 different posts and I can see how this can get confusing and intimidating for someone who is a newbie with wiring. I used to work for Toyota and Lexus for 6 years, so its a bit easier for me to understand.
Great job though. looks fun, I can't wait to do this to mine! I have been talking about doing this for a LOOONG time when I found out that the 2zr was the Yaris TS version.