Agreed. There was a Civic that showed up from time to time locally (prepped for nationals) and whooped up on everyone. And even then, he had a lot of room to improve for national level competitiveness. My hamfisted technique was no match for him. =)Originally Posted by ArmstrongRacing ↑I am keeping a close eye on Mike H. and that RSX....and my goal is to beat his time eventually. You guys must also understand he is a National champ level driver in a FAST car. Im sure a really good driver could beat him with how my car currently sits, but a 130hp yaris on springs isnt the same as a fully prepared RSX.
The 2zr-fe engine swap guide
414 posts · 433,293 views · page 5 of 9
Replies continued
^ This is what Ive been anticipating all year....to see where I stand against "The Beast"Originally Posted by Jason@SportsCar ↑I think something a little bigger is going to be his challenge.😆
Picture not included in this copy
I wouldn't really call Bretts car "the beast". Back in 2013 I could usually keep within a second or two of that car, even with his wing and R comp tires. He generally couldn't keep up with the Wongs or Will Kalman in their STC cars.
Oh....in that case I may have a chance with the R1's!
I talked to RPM today and started setting up a wholesale account. Everyone that completes a 2zr swap will get a discount on the long tube header and midpipe!
Picture not included in this copyOriginally Posted by ArmstrongRacing ↑I talked to RPM today and started setting up a wholesale account. Everyone that completes a 2zr swap will get a discount on the long tube header and midpipe!
So... I wonder if they do rebates after the fact? LoLOriginally Posted by ArmstrongRacing ↑I talked to RPM today and started setting up a wholesale account. Everyone that completes a 2zr swap will get a discount on the long tube header and midpipe!
They mentioned your header when we talked, Ill see what we can do. If we cant work out a rebate, maybe I can send you some Amsoil at cost to make up for it.Originally Posted by brushforhire ↑So... I wonder if they do rebates after the fact? LoL
Ok this thread is BS, I should not have read it now my Bronco might have to spend another year not getting FG body parts :(
I guess I'll find out eventually, anyone know the legality of this swap with an older than 2011 engine into a 2011 Yaris in British Columbia? I guess I could look for a older Yaris with a bad/blown engine and swap in a newer engine.
I guess I'll find out eventually, anyone know the legality of this swap with an older than 2011 engine into a 2011 Yaris in British Columbia? I guess I could look for a older Yaris with a bad/blown engine and swap in a newer engine.
I see you have a wheelwell profile. Get Matt Farah to do a one take!
I Already have an appointment with him for May 2nd, hoping my header is done on time!Originally Posted by Supra_Yaris ↑I see you have a wheelwell profile. Get Matt Farah to do a one take!
Nice! Lookin forward to the video
Nice! Can't wait to see it!Originally Posted by ArmstrongRacing ↑I Already have an appointment with him for May 2nd, hoping my header is done on time!
I thought I should tell you guys about something cool I've noticed with the 2zr. After driving this around and racing I believe anyone(like myself) would get accustomed to the additional power after a while. But there is one aspect I LOVE that you guys will also notice and appreciate.
When accelerating to change lanes or to get onto the interstate the car accels normally until right around 4000rpm....after 4 it feels like you have vtec and you get this surge forward all the way to redline. It's so addictive!
When accelerating to change lanes or to get onto the interstate the car accels normally until right around 4000rpm....after 4 it feels like you have vtec and you get this surge forward all the way to redline. It's so addictive!
Pardon my mechanical ignorance, but isn't VVT-i just V-Tech under a diff name? I've done a little research, but haven't been able to understand the difference. They're both just variable valve timing, right? Why is it that the Honda guys talk about 'V-Tech kicking in' and it seems VVT-i doesn't?Originally Posted by ArmstrongRacing ↑....after 4 it feels like you have vtec and you get this surge forward all the way to redline.
My understanding it vtec has valve lift where vvt-i is just variable timing. You essentially notice more "boost" w/ vtec but vvti is spread out more evenly through the rpm range.Originally Posted by ern-diz ↑Pardon my mechanical ignorance, but isn't VVT-i just V-Tech under a diff name? I've done a little research, but haven't been able to understand the difference. They're both just variable valve timing, right? Why is it that the Honda guys talk about 'V-Tech kicking in' and it seems VVT-i doesn't?
The 2zr has dual vvti and I thought it also has valve lift capabilities which is likely why you feel the pick up after 4k.
Someone correct my post if incorrect
True VTEC (there are other ECO Vtecs now) has 3 lobe intake and/or exhaust cams that operate via a VTEC solenoid operated by raising oil pressure and the vehicles ECU to switch between a low lobe lift/duration initally and then a secondary lobe which has little more, and then to one that has very aggressive rates for life/duration. Modern I-VTEC also control timing on the intake cam via VTC in addition to the more aggresive intake/exhaust cams as revs rise.
If you ever go to a meet or show and see a loud high idle Honda, they're usually running a "VTEC KILLER" which is eliminiting the lost motion system which allows the lobes to change and just running the 3rd lobe which is hte most agressive. They dont' idle right under normal idle conditions because the cam profiles are too big.
If you ever go to a meet or show and see a loud high idle Honda, they're usually running a "VTEC KILLER" which is eliminiting the lost motion system which allows the lobes to change and just running the 3rd lobe which is hte most agressive. They dont' idle right under normal idle conditions because the cam profiles are too big.
Originally Posted by tmontague ↑My understanding it vtec has valve lift where vvt-i is just variable timing. You essentially notice more "boost" w/ vtec but vvti is spread out more evenly through the rpm range.
The 2zr has dual vvti and I thought it also has valve lift capabilities which is likely why you feel the pick up after 4k.
Someone correct my post if incorrect
Interesting, thanks.Originally Posted by MugenRep ↑True VTEC (there are other ECO Vtecs now) has 3 lobe intake and/or exhaust cams that operate via a VTEC solenoid operated by raising oil pressure and the vehicles ECU to switch between a low lobe lift/duration initally and then a secondary lobe which has little more, and then to one that has very aggressive rates for life/duration. Modern I-VTEC also control timing on the intake cam via VTC in addition to the more aggresive intake/exhaust cams as revs rise.
If you ever go to a meet or show and see a loud high idle Honda, they're usually running a "VTEC KILLER" which is eliminiting the lost motion system which allows the lobes to change and just running the 3rd lobe which is hte most agressive. They dont' idle right under normal idle conditions because the cam profiles are too big.
The 2zr does not have valve lift, only cam advance and retard. Another interesting bit of info is that the 2zr uses the same hydraulic lash adjusters as the V6 2grfe. Completely different system VS the 1nz.
Now if only I had a spare set of 2zr cams to send out for a regrind!
Now if only I had a spare set of 2zr cams to send out for a regrind!
Spare cams are always tricky to come across unless of course you do things like over boost the snot out of the engine and blow 8 holes through the block....lol.
Sent from m-o-b-i-l-e
Sent from m-o-b-i-l-e
Well I would probably just buy a longblock from the auto recyclers, they are only $800.
Jason has informed me that the regrinds are not ideal for us Solo racers, because we need torque more than horsepower. So for now I'm going to focus on getting an LSD.
Jason has informed me that the regrinds are not ideal for us Solo racers, because we need torque more than horsepower. So for now I'm going to focus on getting an LSD.
Update: 4,340 miles accumulated on my 2zr, I have my oil sample bottle ready. My RPM long tube header is on the way....and Im set up to do baseline dyno pulls tomorrow with the 2zr stock
That sounds awesome, i wonder if you'll break 115 fwhp with it the way it is, and what kind of gain the long tube will give.
This is what I pulled from one of the scion sites:
Originally posted by Richard Holdener (Dynatek)
Here are the dyno results of the new long-tube header for the 1.8L Yaris TS and Scion xD (possibly other apps as well).
Equipped with just a home-made air intake, the otherwise stock Xd produced 123 wheel hp and 121 ft-lb of torque.
Equipped with the long-tube headers and 2.5-inch mid pipe (2.25 would work equally well) and no axle back, the motor produced 134 wheel hp and 134 ft-lb of torque.
At just 3000 rpm, the header and mid pipe offered an additional 15 ft-lb of torque.
Next we installed the prototype of the Xd intake manifold. The peak power numbers jumped to 148 hp and 137 ft-lb of torque.
At 6000 rpm, the intake offered gains of 16 hp.
It appears from this testing that if we add an NST u-pulley and receive the same results as we did on the 1.5L Yaris motor, the 1.8L can produce a real 150 wheel hp (possibly more if it reponds favorably to the FIC).
BTW-We already made 151 wheel hp with a version of the intake that won't be offered for sale-it adds a bit more peak power but sacrafices too much elsewhere)
Originally posted by Richard Holdener (Dynatek)
Here are the dyno results of the new long-tube header for the 1.8L Yaris TS and Scion xD (possibly other apps as well).
Equipped with just a home-made air intake, the otherwise stock Xd produced 123 wheel hp and 121 ft-lb of torque.
Equipped with the long-tube headers and 2.5-inch mid pipe (2.25 would work equally well) and no axle back, the motor produced 134 wheel hp and 134 ft-lb of torque.
At just 3000 rpm, the header and mid pipe offered an additional 15 ft-lb of torque.
Next we installed the prototype of the Xd intake manifold. The peak power numbers jumped to 148 hp and 137 ft-lb of torque.
At 6000 rpm, the intake offered gains of 16 hp.
It appears from this testing that if we add an NST u-pulley and receive the same results as we did on the 1.5L Yaris motor, the 1.8L can produce a real 150 wheel hp (possibly more if it reponds favorably to the FIC).
BTW-We already made 151 wheel hp with a version of the intake that won't be offered for sale-it adds a bit more peak power but sacrafices too much elsewhere)
That's damn good power, was it auto as well? If so a manual 2zr would probably break 130 with just an intake.
Brushforhire: You are installing your long tube soon, any chance you can do a couple of in car videos of how she accelerates?
Brushforhire: You are installing your long tube soon, any chance you can do a couple of in car videos of how she accelerates?
I wonder if the 2zr-fe lower end can hold a 1nr-fe head and work with the iQ front differential? I guess it would depend it if mounts to the transmission. Maybe I'll order an iQ tranny gasket and Xd tranny gasket and compare.
Not totally sure about the trans that was dyno'd.Originally Posted by LTHatch ↑That's damn good power, was it auto as well? If so a manual 2zr would probably break 130 with just an intake.
Brushforhire: You are installing your long tube soon, any chance you can do a couple of in car videos of how she accelerates?
I can try and figure out how to take some vids. I don't really have anything that would work well. Holding my Nikon would be really awkward, lol. Maybe time to get a gopro.
Im pretty sure their results are from a manual transmission car, it's impossible to do a full rev-range dyno pull with the auto, Because you cant keep it from down-shifting below 3000RPM.Originally Posted by LTHatch ↑That's damn good power, was it auto as well? If so a manual 2zr would probably break 130 with just an intake
;-)Originally Posted by ArmstrongRacing ↑Im pretty sure their results are from a manual transmission car, it's impossible to do a full rev-range dyno pull with the auto, Because you cant keep it from down-shifting below 3000RPM.
Sent from m-o-b-i-l-e
Brushforhire: That's far too much especially after what you've invested in the swap, i'll just keep an eye for your review on your 2zr Yaris.
ArmstrongRacing: Ahh i see thank you, didn't know that about automatic transmissions.
ArmstrongRacing: Ahh i see thank you, didn't know that about automatic transmissions.
This weekend was the SCCA Oceanside Showdown in San Diego. Since I am allowed Rcomps in SMF I ran a set or used BFG R1 S tires. They didnt help me at all, I have no experience with these tires and I drove them like a street tire, they never went above 130 degrees in a 50 second course. I got destroyed by the Yawsport TL.
http://youtu.be/DRo1OAZsBkg
They weighed my car after the competition and its at 2362, so I sisnt gain any weight from the 2zr swap!
http://youtu.be/DRo1OAZsBkg
They weighed my car after the competition and its at 2362, so I sisnt gain any weight from the 2zr swap!
I received my RPM long-tube header, now To get this installed by May 2nd for the "one take" with Matt Farah.
1 attachment not included in this copy
i love itOriginally Posted by ArmstrongRacing ↑I received my RPM long-tube header, now To get this installed by May 2nd for the "one take" with Matt Farah.
side note: do you think the new corolla 6 speed would fit on your 2zrfe in your yaris engine bay?
by extension, would the corolla 6 speed bolt to a 1nzfe AND fit between the frame rails?
When we swapped the Xd 2zt/C50 into Computerlove's 09 LB, we used a big hammer to make room....so I would assume it would be the same procedure for any non-1nz power trainOriginally Posted by thebarber ↑i love it
side note: do you think the new corolla 6 speed would fit on your 2zrfe in your yaris engine bay?
by extension, would the corolla 6 speed bolt to a 1nzfe AND fit between the frame rails?
Fun watch, thanks for sharing.Originally Posted by ArmstrongRacing ↑
No hammer needed when using a EC series 6sp transmission,the cases of the new EC 6sp transmissions are shorter,the length is about the same as the older 5 sp
c series transmissions.This is due to new case and gear design, Toyota went to a 2 piece case design.(c transmissions are a three piece case)
In Europe ,the yaris used a EC 6 sp on later generations of the 1.8 ts and 1.33.
c series transmissions.This is due to new case and gear design, Toyota went to a 2 piece case design.(c transmissions are a three piece case)
In Europe ,the yaris used a EC 6 sp on later generations of the 1.8 ts and 1.33.
Here are some pictures from my RPM long tube header install...
1 attachment not included in this copy
No way around it, the coating will get scratched upon install. I had to bend the bracket tab to get this in from underneath, and I also had to make a indent on the firewall for A/F sensor clearance
1 attachment not included in this copy
This is how my exhaust shop did my midpipe. RPM sent me an extra flange and gasket to make this a bolt-in header. I highly recommend installing a flex joint though, as I get a lot of vibration at idle with the a/c on...
1 attachment not included in this copy
This is my rear O2 sensor extension, this is required with the RPM header due to its length.
1 attachment not included in this copy
Very nice.
True, but the EC uses a special throwout bearing with an integrated cylinder, which means your clutch system has to be changed to accommodate it. You could probably fab up your own lines, but I don't know if the US clutch master cylinder would work with the EU integrated throwout bearing/cylinder.Originally Posted by froger ↑No hammer needed when using a EC series 6sp transmission,the cases of the new EC 6sp transmissions are shorter,the length is about the same as the older 5 sp
c series transmissions.This is due to new case and gear design, Toyota went to a 2 piece case design.(c transmissions are a three piece case)
In Europe ,the yaris used a EC 6 sp on later generations of the 1.8 ts and 1.33.
The ZSP90 used the same clutch master cylinder with the C56 and EC67.
If you bought an EC67 and it didn't come with any of the hydraulics, the following parts are what you'd need:
31400-59015 - Cylinder, Slave (with integrated release hub, includes bolts)
31407-52010 - Bleeder, Clutch Slave
91551-80820 - Bolt, Clutch Slave Bleeder (Qty: 2)
31482-52090 - Tube, Clutch (Slave to Bleeder)
31126-20090 - Boot, Clutch Tube
31482-52100 - Tube, Clutch Bleeder to Flexible Hose
90461-08567 - Clamp, Bleeder to Hose Tube
31484-52160 - Bracket, Tube to Hose (Transmission Side)
91671-80810 - Bolt, Tube and Bracket (Qty: 2)
90947-02G28 - Hose, Transmission to Body
Everything on the body side is the same between the C56 and EC67.
There are LH mount differences as well, however the RH/rear mounts are the same for C56 and EC67. The axles are the same between the two as well.
12372-37141 - Mount, RH Side
12325-37100 - Bracket, RH Mount
12351-37100 - Damper, RH Mount
Jeff
If you bought an EC67 and it didn't come with any of the hydraulics, the following parts are what you'd need:
31400-59015 - Cylinder, Slave (with integrated release hub, includes bolts)
31407-52010 - Bleeder, Clutch Slave
91551-80820 - Bolt, Clutch Slave Bleeder (Qty: 2)
31482-52090 - Tube, Clutch (Slave to Bleeder)
31126-20090 - Boot, Clutch Tube
31482-52100 - Tube, Clutch Bleeder to Flexible Hose
90461-08567 - Clamp, Bleeder to Hose Tube
31484-52160 - Bracket, Tube to Hose (Transmission Side)
91671-80810 - Bolt, Tube and Bracket (Qty: 2)
90947-02G28 - Hose, Transmission to Body
Everything on the body side is the same between the C56 and EC67.
There are LH mount differences as well, however the RH/rear mounts are the same for C56 and EC67. The axles are the same between the two as well.
12372-37141 - Mount, RH Side
12325-37100 - Bracket, RH Mount
12351-37100 - Damper, RH Mount
Jeff
Wow, that's awesome work!Originally Posted by Jeff Lange ↑The ZSP90 used the same clutch master cylinder with the C56 and EC67.
...
Jeff
So this happened...
1 attachment not included in this copy
Awesome. When does it air?
I've been looking forward to that video for a while! Let us know when it's put up