Yarisworld Archive

The 2zr-fe engine swap guide

414 posts · 433,293 views · page 2 of 9

Replies continued

fredovvtiSabana Grande, PR · Jan 21, 2016#51
If I get a complete xD harness and use the Yaris trans, I only have to move the pins that you mention in post #48 to the correct location of the plugs ends and that its?
ArmstrongRacingThread starterSan Diego · Jan 21, 2016#52
Originally Posted by beaker ↑
So the MAF (CA2#9) needs to see +12volts with ignition on? It's not a signal coming out of the MAF with variable voltage output going back into the ECM?
Correct. The MAF black wire is the power supply to the sensor....the other 4 wires go directly to the ECM.

Originally Posted by fredovvti ↑
If I get a complete xD harness and use the Yaris trans, I only have to move the pins that you mention in post #48 to the correct location of the plugs ends and that its?
Correct, for now. There is more wiring later but this is all regarding the engine.
ArmstrongRacingThread starterSan Diego · Jan 21, 2016#53
Originally Posted by ilikerice ↑
You are mixing scenario's up in 2 different posts and I can see how this can get confusing and intimidating for someone who is a newbie with wiring.
Im sorry for the confusion, but I mention the Corolla harness because thats what I'm using on my 2zr/yaris trans buid. I wanted to test ALL of the Corolla parts so no one else would have to. I want this to be easy for everyone, so again just to be clear........aside from the actual engine and accesories, USE EVERY PART FROM A SCION XD.

I know you guys would prefer this diy be formatted a certain way, but I am sharing this info with you guys as I go.
3cyltrboOttawa · Jan 21, 2016#54
Originally Posted by Rigaud ↑
No municipality has a say in emissions in Canada. Regulated by Federal then Provincial.
Some municpalities (example in the North, like Sudbury) have traditionally been able (through their say) to become exempt from having the same standards.

I know this because its been popular at times for people from around Ottawa to try and register their cars with a northern address in order to be exempt from the requirement to do emissions testing.

WC
3cyltrboOttawa · Jan 21, 2016#55
Originally Posted by ArmstrongRacing ↑
If you couldn't locate a Xd harness than your swap(like mine) is going to be much more involved wiring wise...

The Corolla harness has 3 plugs on the fusebox end and none of them match the yaris. You must move every single wire to its corresponding location in the yaris' CA1 and CA2 plugs.(I'm almost done). In addition to re-pinning, you will also have to cut the 2zr harness battery cables going to the starter/alternator and connect them to your 1nz harness cables for the extra length and the proper ends....lots of work.

NOTE: You can see my mini add-a-circuit for the MAF here
Is there also a difference because your car is an automatic? (ie: are there additional wiring and harness implications because of the automatic?)
ArmstrongRacingThread starterSan Diego · Jan 21, 2016#56
There is no additional wiring involved in having an automatic vs manual transmission. If your car is auto and you keep it auto, the auto trans Xd harness and ECM have the same pin locations at the transmission plugs. There is only one wire to ground, Ill get to that later
3cyltrboOttawa · Jan 21, 2016#57
Originally Posted by ArmstrongRacing ↑
There is no additional wiring involved in having an automatic vs manual transmission. If your car is auto and you keep it auto, the auto trans Xd harness and ECM have the same pin locations at the transmission plugs.

Where I'm coming from is 2010 Yaris 5spd manual without ABS

So, just like some of the others, as I read through your helpful posts.....I try to harvest the info for my own situation (ie: which mounts / tranny / axles / wiring etc...)

Will
ArmstrongRacingThread starterSan Diego · Jan 22, 2016#58
I finished all of my Corolla harness soldering today. I connected the battery and switched on the ignition and I immediately got a code for P2770-Torque Converter Clutch(auto trans).....Im not sure if this is a result of the hydrolock or what, looks like I need to do a bit more research...

Tomorrow I will finish my MAF wiring and fire it up...hopefully all goes well.

1 attachment not included in this copy

beakerconyers ga · Jan 22, 2016#59
Originally Posted by ArmstrongRacing ↑
I finished all of my Corolla harness soldering today. I connected the battery and switched on the ignition and I immediately got a code for P2770-Torque Converter Clutch(auto trans).....Im not sure if this is a result of the hydrolock or what, looks like I need to do a bit more research...

Tomorrow I will finish my MAF wiring and fire it up...hopefully all goes well.
So far, it was just four wires you had to change? (pending figuring out the P2770 code of course)
ArmstrongRacingThread starterSan Diego · Jan 22, 2016#60
Originally Posted by beaker ↑
So far, it was just four wires you had to change? (pending figuring out the P2770 code of course)
For the Xd manual trans harness yes, 4 wires so far.

Update: (auto trans only) I've found the harness discrepancy causing my P2770 code. The Xd ECM normally receives a signal from the SL solenoid on pin#58, but my Corolla harness has that wire on 57. Also the Corolla/Xd valve body's ground this solenoid internally vs the Yaris auto trans grounding this solenoid at the ECM. I just need to swap pins 57 to 58 and ground pin #9 at the valve body connector.
maralieuscool california · Jan 22, 2016#61
So what did you need for cali smog? You just had to call ahead and tell them your plans and that's it? Then just make sure it has no check engine, cat, and that's about it? I'm very interested in doing this swap as my yaris tranny is getting iffy and the engine has 150k so it is in the cards.
ArmstrongRacingThread starterSan Diego · Jan 22, 2016#62
Yes I called the BAR and they said no CEL, and all stock components.
ArmstrongRacingThread starterSan Diego · Jan 23, 2016#63
This is the ECM I ordered from Ebay...I just have to finish up some wiring and Ill have a engine startup video.

1 attachment not included in this copy

Bluevitz-rsOshawa, Ontario, Canada · Jan 24, 2016#64
what's the engine immobilizer situation and how are you addressing it?
ArmstrongRacingThread starterSan Diego · Jan 24, 2016#65
My car does not have immobilizer, so I bought a non-immobilizer ECM. I believe all pre 2010 Xd's are non immobilizer.

If your car has immobilizer....I still dont know what exactly has to be done regarding keys. Someone will have to try it, or have the system removed.
CoryMWhite Rock BC · Jan 24, 2016#66
Originally Posted by ArmstrongRacing ↑
I know you guys would prefer this diy be formatted a certain way, but I am sharing this info with you guys as I go.
You're doing great. Keep it up! Whenever I do something worth sharing, I always find it difficult to document until after it's done. The effort is appreciated.

Cheers.
3cyltrboOttawa · Jan 24, 2016#67
Originally Posted by CoryM ↑
You're doing great. Keep it up! Whenever I do something worth sharing, I always find it difficult to document until after it's done. The effort is appreciated.

Cheers.
+1
ArmstrongRacingThread starterSan Diego · Jan 24, 2016#68
Originally Posted by CoryM ↑
Whenever I do something worth sharing, I always find it difficult to document until after it's done.
This is exactly how I felt about this diy, there is so much going on I feared a step would get forgotten if I waited until it was completed.
beakerconyers ga · Jan 24, 2016#69
Originally Posted by ArmstrongRacing ↑
This is exactly how I felt about this diy, there is so much going on I feared a step would get forgotten if I waited until it was completed.
You're doing great! Worthy of many accolades for doing and sharing with the rest of us this engine swap.

Would you mind posting the part # of the ECM you bought, and what it was for?(ie year make model and specific options)
beakerconyers ga · Jan 24, 2016#70
Originally Posted by ArmstrongRacing ↑
I finished all of my Corolla harness soldering today. I connected the battery and switched on the ignition and I immediately got a code for P2770-Torque Converter Clutch(auto trans).....Im not sure if this is a result of the hydrolock or what, looks like I need to do a bit more research...

Tomorrow I will finish my MAF wiring and fire it up...hopefully all goes well.
How did the wiring go for the corrolla harness to XD/yaris? Any left over wires, or were you able to terminate/find a place for all the wires? Just wondering how viable using a corrolla harness is.
ArmstrongRacingThread starterSan Diego · Jan 24, 2016#71
Originally Posted by beaker ↑
Would you mind posting the part # of the ECM you bought, and what it was for?(ie year make model and specific options)
I mentioned the ECM part# in post #23....for an automatic transmission it is: 89661-52F71.

Originally Posted by beaker ↑
How did the wiring go for the corrolla harness to XD/yaris?
The Corolla harness has all of the necessary wires to connect successfully to the Yaris. The cons however are that it's a monumental task soldering all of the wires, and the ecm plug is not long enough to reach the original ECM location....I had to mount mine above the valve cover on the cowl. There are also a couple wires to change for the transmission plug.
ArmstrongRacingThread starterSan Diego · Jan 25, 2016#72
For those of you with a auto transmission: If you use a Xd harness you won't need this step. If you used the Corolla harness pin#57 needs to be moved to #58. This is for the Sl/Slu+ solenoid.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jan 25, 2016#73
This is the lock on the main harness connector(C20). You have to pop this grey tab out about 1mm before you can release the pins.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jan 25, 2016#74
Next you need to slide a small pin into the pin release hole. Pull on the white #57 wire and wiggle a bit until it slides out.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jan 25, 2016#75
Pop out the little rubber seal in pin location #58, and slide the wire in until it clicks. Install the rubber seal back into #57, then push the grey lock tab back in.

FYI: This pin removal/install procedure is the same for the ABS module plug, in case you used a Xd trans with no speed sensor.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jan 27, 2016#76
This is the last of the auto trans related wiring. Because the Corolla/Xd have different ground circuits than the Yaris for the Sl solenoid, you need to open the trans harness about 8" from the plug and cut the blue wire at pin #9. Pull the wire out of the harness while still connected to the connector and attatch a eyelet, the ground the wire to the trans case here.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jan 27, 2016#77
Now that all the wiring is complete, lets be sure the ECM is happy........yep, time to charge the a/c and take it for a drive...

1 attachment not included in this copy

ilikericesavannah, ga · Jan 28, 2016#78
YAAAAAY!

Congrats....

Only reason I am upset is because you have a CamCon that you were going to tune with the 1nz and share a mild tune with me.................😢
ArmstrongRacingThread starterSan Diego · Jan 28, 2016#79
Thanks man.

Haha, Im sorry about the tune.....I never had a chance to install the Camcon either, life threw me a lemon and I had to make a batch of oh-so-sweet lemonade!

On a side note.....holy crap this car is a BLAST!
tmontagueCaledonia Ont. · Jan 28, 2016#80
so was the faulty trans ground the reaosn for the previous CEL that was regarding the torque converter?
ArmstrongRacingThread starterSan Diego · Jan 28, 2016#81
Originally Posted by tmontague ↑
so was the faulty trans ground the reaosn for the previous CEL that was regarding the torque converter?
It wasnt a faulty ground, just a difference in how the Corolla/xd is wired inside the transmission valvebody...2 wire changes and done.
tmontagueCaledonia Ont. · Jan 28, 2016#82
I see, but that wire you just grounded above was the reason for the torque converter cel?
ArmstrongRacingThread starterSan Diego · Jan 28, 2016#83
That's correct
ern-dizCA all day · Jan 28, 2016#84
Why, oh why, are you holding out on the first start and test drive vid! 😁
ArmstrongRacingThread starterSan Diego · Jan 28, 2016#85
Ive edited the videos together up to this point, I need to do a test drive video along with some footage of this weekends autocross.
asproToronto, Canada · Jan 29, 2016#86
Im curious to see your time differences in autocross between the 1nz and 2zr... Ill be watching this closely. Good job btw, i bet a lot of people have been putting diesel fuel in there yaris' to justify an engine swap... Or maybe thats just me. :p
tmontagueCaledonia Ont. · Jan 29, 2016#87
Originally Posted by aspro ↑
i bet a lot of people have been putting diesel fuel in there yaris' to justify an engine swap... Or maybe thats just me. :p
👍
invader166Langley, BC · Jan 29, 2016#88
I wonder...is there a big weight difference between the 2 engines?
ArmstrongRacingThread starterSan Diego · Jan 29, 2016#89
On every engine Ive owned Ive had one of these guys. It never hurts to monitor your oil pressure especially when you push the engine like we do. This is a decent quality electronic gauge with a sender(not the nylon tube). Reasonably priced at $84. I normally remove the stock "dummy light" oil pressure switch and install the gauge sensor in that port. You'll also need Auto Meter adaptor #2269 because the block port is BSPT vs most oil pressure senders are NPT.

1 attachment not included in this copy

tmontagueCaledonia Ont. · Jan 29, 2016#90
Are you using a sandwich plate at the oil filter mount, or are you just removing the stock dummy sensor to plug the sender into?

I'll be wiring up oil pressure, oil temp and hopefully an afr gauge next summer. I agree it's very valuable to know when the engine is being pushed.
ArmstrongRacingThread starterSan Diego · Jan 29, 2016#91
There is no way to use a sandwich plate adaptor on the 2zr, it has a canister filter. The gauge sensor goes where the dummy light switch is.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jan 30, 2016#92
I would like everyone to read through this guide and inform me of any unclear elements. Also, Is this thread going to be a sticky or will it disappear once everyone gets over the excitement
7:34pmBritish Columbia · Jan 30, 2016#93
I've been following this thread since start, and I know it's a long shot...

But I think it would be helpful to see something like this (below), so that people can get sense of what their options are.

I recall you saying the Xd swap was easy, only four wires, and I think a lot of people thought the corolla swap was going to be the same idea. That's probably why the confusion in the earlier pages when they saw you doing the wiring.

Would be nice to outline what was used for the swap, as far as what ECU is needed, what axles are compatible, transmission options, what mounts to use, technical difficulty of wire splicing involved, etc. I know you haven't done the Matrix swap, yet 😁, but that could stay blank for now...

You should also do up a DIY on that oil pressure gauge!

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jan 30, 2016#94
Yeah.....Im not creating a chart. If you or someone else wants to create a chart ill be happy to share the info with you. I did however add a list of components to post #1.

Update: 232 problem free miles accumulated so far, no CEL, and EVERYTHING works fine. My first autocross is tomorrow, look for the video on my YouTube channel or FB page.
CrankyOldManWest Michigan · Jan 31, 2016#95
Originally Posted by 7:34pm
I've been following this thread since start, and I know it's a long shot...

But I think it would be helpful to see something like this (below), so that people can get sense of what their options are.
It depends on what exactly you want the chart to contain. Are you looking at basic compatibility, or do you want all of the gory details like wire swap/pin locations?
I recall you saying the Xd swap was easy, only four wires, and I think a lot of people thought the corolla swap was going to be the same idea. That's probably why the confusion in the earlier pages when they saw you doing the wiring.
If you choose carefully, there's not a lot of wiring involved. The hurdle that Armstrong was up against was that his wire harness arrived without the fuse box connectors. It was just chopped off, so he had to splice in the connections. That said, I think the sedan connectors aren't compatible with the Corolla wire harness anyway, so you'd have to either sacrifice the original sedan wire harness or score one from a junk yard. The other option is to use both the 1NZ and 2ZR wire harnesses: strip them all the way down and then move wires/pins to the connectors that go on the finished vehicle.
Would be nice to outline what was used for the swap, as far as what ECU is needed, what axles are compatible, transmission options, what mounts to use, technical difficulty of wire splicing involved, etc. I know you haven't done the Matrix swap, yet 😁, but that could stay blank for now...
The general rule is that the gearbox can stay. If you want the bigger axles and 5x100 hubs, swap in the xD gearbox, axles and hubs. Everything else depends on what wire harness you start with and which year/style your donor and recipient vehicles are. A quick look at the connector diagrams for the Matrix looks like it's identical in layout to the Corolla--though not necessarily the same electrically. Most of the electrical questions can be answered in the repair manual/EWD, which I downloaded at the same time as the Corolla. =)
ArmstrongRacingThread starterSan Diego · Feb 1, 2016#96
Good info Cranky, good work.

On a side note, the 2zrVios took a foul weather win today in SMF. 2 Civics and a Mini fell victim to the 2zr. You can see a short video clip on my FB page:

https://m.facebook.com/story.php?sto...1&ref=bookmark
CrankyOldManWest Michigan · Feb 1, 2016#97
Originally Posted by ArmstrongRacing ↑
Good info Cranky, good work.

On a side note, the 2zrVios took a foul weather win today in SMF. 2 Civics and a Mini fell victim to the 2zr. You can see a short video clip on my FB page:

https://m.facebook.com/story.php?sto...1&ref=bookmark
No need to thank me, just part of what I do for the YW community. =)

I love the comment from the announcer: "...an automatic Yaris! Oh no!"
ArmstrongRacingThread starterSan Diego · Feb 1, 2016#98
Haha, the amount of trash talk I hear about the auto from people that dont know me is funny...people don't understand circuit racing is 70% driver skill....within classes a small percentage of what makes you a winner is car setup.
Frank the TankToronto · Feb 1, 2016#99
Originally Posted by ArmstrongRacing ↑
Also, Is this thread going to be a sticky or will it disappear once everyone gets over the excitement
Saving up for this swap as we speak. I'm excited everyday.
CrankyOldManWest Michigan · Feb 2, 2016#100
Originally Posted by ArmstrongRacing ↑
...Is this thread going to be a sticky or will it disappear once everyone gets over the excitement
Looks like TK-421 has been active recently. He's one of the few moderators that still checks in. Try sending him a PM.