Yarisworld Archive

tooter's manifold adventure...

1,454 posts · 559,522 views · page 22 of 30

Replies continued

cali yarisCanoga Park, CA · Jan 31, 2013#1051
Setting the record straight:

1. The Yaris stock pulley DOES have a small rubber damping strip.
2. Straight from a Toyota engineer: "The purpose is to reduce noise in the cabin ONLY; it has nothing whatsoever to do with engine longevity".
3. Conclusion: An aftermarket pulley might cause a bit more cabin noise/vibration, but that is all.
4. #3 is proven by the hundreds of aftermarket Yaris pulleys out there with not one provable engine failure or shred of evidence that a solid pulley causes damage on this car.
5. This has all been covered over and over again on this forum and many others -- anyone bothering to do a search first wouldn't need to rehash the argument, at least in reference to the Yaris.

Are we good now? 🙂
Kaotic LazagnaCentral Valley, CA · Jan 31, 2013#1052
Originally Posted by malibuguy ↑
^ buy my old exhaust from antho ;) hes selling it cheap
I'd love to since that's one of the best sounding exhausts on a Yaris I've heard. But, any extra cash (which is 0 right now) I have will have to go towards camera gear (camera gear can make me money, whereas modding my car eaets my money 😆).
malibuguyWestminster, MD · Feb 3, 2013#1053
cant have ying without the yang ;)
Kaotic LazagnaCentral Valley, CA · Feb 4, 2013#1054
Originally Posted by malibuguy ↑
cant have ying without the yang ;)
lol, once I get some paying gigs, I'll have some extra cash for other hobbies 😉
Flipper_1938Kentucky · Feb 4, 2013#1055
Originally Posted by cali yaris ↑
Setting the record straight:

1. The Yaris stock pulley DOES have a small rubber damping strip.
2. Straight from a Toyota engineer: "The purpose is to reduce noise in the cabin ONLY; it has nothing whatsoever to do with engine longevity".
3. Conclusion: An aftermarket pulley might cause a bit more cabin noise/vibration, but that is all.
4. #3 is proven by the hundreds of aftermarket Yaris pulleys out there with not one provable engine failure or shred of evidence that a solid pulley causes damage on this car.
5. This has all been covered over and over again on this forum and many others -- anyone bothering to do a search first wouldn't need to rehash the argument, at least in reference to the Yaris.

Are we good now? 🙂
They didn't do a damn thing else to reduce cabin noise....why'd they pick the crank hub to sound deaden?
cali yarisCanoga Park, CA · Feb 4, 2013#1056
It reduces vibration felt with the hands through the steering wheel, from what I was told. More vibration than noise, I guess.

Smoothness is associated with more expensive cars? I dunno, nor do I care much.
Bluevitz-rsOshawa, Ontario, Canada · Feb 4, 2013#1057
I don't know about the Yaris, but every one of the motor mounts on the Echo has a big chunk of cast steel mounted to it, two of them rubber mounted for vibration reduction. It just adds weight to the car for all I care about vibrations. The only vibrations I'm ever aware of are at idle.
tooterThread starterLos Angeles · Feb 4, 2013#1058
Well, I actually like it when idling you can't even tell if the engine is on or off except for the needle on the tach...

...but that's just the daily driver in me, I guess. 😉
Captain SlowScott, LA · Feb 5, 2013#1059
lucky you, I've got the A/C idle drop, which is apparently a very common thing on the Yaris. it idles smooth as glass, then dips for a second likes it's going to stall then goes back up. from what I've read though it's very common and considered normal by Toyota techs...something to do with the gas saving features of the car.
tooterThread starterLos Angeles · Feb 5, 2013#1060
Mine also does that to on AC which we hardly ever run. It senses a load and then notches up the idle. The idle also goes up slightly when the lights are turned on.
cali yarisCanoga Park, CA · Feb 5, 2013#1061
Well, I actually like it when idling you can't even tell if the engine is on or off
Tooter, a horse would be too loud for you. 😆
tooterThread starterLos Angeles · Feb 5, 2013#1062
Originally Posted by cali yaris ↑
Tooter, a horse would be too loud for you. 😆
Your excellent exhaust sure isn't, Garm.
Inside the car, it's virtually silent at idle.
Stepping on the gas is another story...
cali yarisCanoga Park, CA · Feb 5, 2013#1063
^ That's a good combination; it's there when you feel the need.
Captain SlowScott, LA · Feb 5, 2013#1064
Wish there was a way I could make my Medalion Touring just a LITTLE quieter...think I might stuff a blanket in my spare tire well.
cali yarisCanoga Park, CA · Feb 5, 2013#1065
Have you coated your wheel wells yet? Makes a pretty big difference, maybe not so much with the exhaust, but with outside noise in general.
Captain SlowScott, LA · Feb 5, 2013#1066
no. with what? just some of that spray undercoating stuff?
cali yarisCanoga Park, CA · Feb 5, 2013#1067
yes -- people have posted up a few pics here and there, dating back to the beginning of this site. I know you can get decent stuff in a can, just CLEAN well and mask off what you don't want painted - I think it's textured black.

Just for clarity I am talking BEHIND the fender liners on the METAL surfaces of the fenders/wheel wells. It does make a difference!
malibuguyWestminster, MD · Feb 7, 2013#1068
^ intresting...i need to look that up
CTScottUSA, CT · Feb 7, 2013#1069
Originally Posted by malibuguy ↑
^ intresting...i need to look that up
I used Herculiner, which is a brush on bed liner and it made a significant difference:

My $67 sound dampening / undercoating
tooterThread starterLos Angeles · Feb 11, 2013#1070
Another tooter just came off the assembly line... 🙂

Picture not included in this copy

Picture not included in this copy

It's also for sale on ebay same as the last one for $495 including free shipping, or direct from me for $450 including free shipping. The do-it-yourself Build Your Own Manifold Kits are also available for $265 including free shipping...
Picture not included in this copy


You can either PM me here, email at greggabi@verizon.net , or phone 310-455-3340.

Greg 🙂
why?harnett county NC · Feb 12, 2013#1071
Originally Posted by Flipper_1938 ↑
They didn't do a damn thing else to reduce cabin noise....why'd they pick the crank hub to sound deaden?
probably because it fit, and it came from another car.
cali yarisCanoga Park, CA · Feb 12, 2013#1072
^ They did a whole bunch of things to reduce cabin noise -- intake system, exhaust system, firewall materials, etc. 🤷
cali yarisCanoga Park, CA · Feb 12, 2013#1073
...but that's just the daily driver in me, I guess.
Is there another driver in you, tooter?
tooterThread starterLos Angeles · Feb 12, 2013#1074
I get more tire noise than anything else, and think it's a combination of hollow spoked alloy rims and inherently noisier tires (Bridgestone Potenzas). Still I don't have any real complaints because the exhaust makes such beautiful music. 🙂

Also got a pleasant suprize... my first registration renewal. It was only $187... and this is for a one year old car. My 17 year old pickup truck is $93.
Flipper_1938Kentucky · Feb 13, 2013#1075
Originally Posted by cali yaris ↑
^ They did a whole bunch of things to reduce cabin noise -- intake system, exhaust system, firewall materials, etc. 🤷
My 01 Echo was considerably quieter on the intake side.
tooterThread starterLos Angeles · Feb 13, 2013#1076
Mine's a little less quiet... 😉

Picture not included in this copy
cali yarisCanoga Park, CA · Feb 13, 2013#1077
^ Tooter, a great project for tire/road noise is to treat your wheel wells with undercoating. Herculiner is a great product for this (but there are also spraycan products readily available) and you'll get a noticeable result.
CrankyOldManWest Michigan · Feb 20, 2013#1078
On a mildly related note, I've just picked up a Blitz S/C, and I'm already thinking of how I can make it work on a 2ZR-FE swap. The first (and craziest) idea was to have a new manifold section cast from aluminum to mate with the wider bore pitch. Expensive, crazy, probably won't end well. The second thought was (drumroll please) to get an adapter made to mate a 1NZ manifold to a 2ZR head. And then it hit me: someone already did! Of course this assumes that the bolt patterns and bore pitch are identical between the two different 1.8L engines, but I'd say there's a pretty good chance of it being the same.
Captain SlowScott, LA · Feb 20, 2013#1079
^ beat me to the Blitz :(

haha

Good luck with it and hope to see some pics/vids once it's installed.
tooterThread starterLos Angeles · Feb 20, 2013#1080
Originally Posted by Captain Slow ↑
^ beat me to the Blitz
You're living up to the name Captain Slow. 😉
Captain SlowScott, LA · Feb 20, 2013#1081
I was only second :D
tooterThread starterLos Angeles · Mar 2, 2013#1082
I ran out of tooter adaptors (and manifolds) and ordered a couple more. This offered the opportunity to slightly tweak the design to remove the 2mm step around the top perimeter so that I don't need to round it off with a Dremel any more... 🙂

Picture not included in this copy

Picture not included in this copy
CrankyOldManWest Michigan · Mar 3, 2013#1083
Conical taper, eh? I'm planning on going to visit my S/C this afternoon so I can take some pics and rubbings. I figured the best way to get scale representation of the surfaces is to do the old graphite-on-paper transfer trick and then add measurements by hand.
malibuguyWestminster, MD · Mar 3, 2013#1084
according to one of the Yaris manuals that screen is for noise reduction. anybody running without it???
tooterThread starterLos Angeles · Mar 3, 2013#1085
Not yet... 😉

You know, I thought about that metal lattice and was searching online to see if anyone else had any negative effects from removal. All I could find was problems with a screen on older cars, but that was in front of the MAF sensor. Removing it messed with the idle and A/F ratio for some vehicles. I can't see how removing it would cause any problems, although I thought it might make for smoother less turbulent airflow across the backside of the butterfly when it's less than fully open. The air flow over the tipped in end of the butterfly is smoother because it's slanted in the right direction whereas the backside tips upward into the airflow.

I just played it safe and used standard readily available off the shelf stock Toyota O ring gaskets on both ends. The metal lattice can simply be snipped out if desired.
tooterThread starterLos Angeles · Mar 3, 2013#1086
Originally Posted by CrankyOldMan ↑
Conical taper, eh? I'm planning on going to visit my S/C this afternoon so I can take some pics and rubbings. I figured the best way to get scale representation of the surfaces is to do the old graphite-on-paper transfer trick and then add measurements by hand.
Yes, the machined taper is so slight and even you can't see it...

Picture not included in this copy

...and naturally everything gets bead blasted. 😉
tooterThread starterLos Angeles · Mar 4, 2013#1087
Oh, oh... looks like tooter has gone off on another adventure... 🙂

Picture not included in this copy

This one was totally nasty. It took a whole can of engine degreaser just to get it looking like this. I hate working with dirty parts, so at least I can handle the manifold without getting black hands.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

...and this one is pure R & D (Research and Development). I haven't yet decided exactly how to go about this because it's something totally outside the box. So I'll let you guys know when my idea actually takes shape. 😉
CrankyOldManWest Michigan · Mar 4, 2013#1088
MUAHAHAHAHAHAHAHA!
JustDidItUnited States · Mar 4, 2013#1089
Awesome! Can't wait 2 see what you come up with.. 👍
tooterThread starterLos Angeles · Mar 5, 2013#1090
It's gonna be a real doozy... 😉
I'm sourcing the raw materials.
malibuguyWestminster, MD · Mar 7, 2013#1091
i like your thinking
tooterThread starterLos Angeles · Mar 7, 2013#1092
This whole project has been so much fun. 🙂
One idea always leads to another so I'm going to follow them off the beaten path just to find out where they lead. It's my favorite kind of experimental approach:

"Adapting things to an unintended purpose." 😛
malibuguyWestminster, MD · Mar 7, 2013#1093
I thought about recreating the plenum when I go to do mine...just because the factory is so damn ugly. But I wonder if a larger volume could benift even more?
CrankyOldManWest Michigan · Mar 7, 2013#1094
Originally Posted by tooter ↑
This whole project has been so much fun. 🙂
One idea always leads to another so I'm going to follow them off the beaten path just to find out where they lead. It's my favorite kind of experimental approach:

"Adapting things to an unintended purpose." 😛
Aah yes, the old "under-utilized engineer" syndrome: if you don't give them problems to solve, they start making up their own.

I had also played with some ideas for a new plenum involving 6" aluminum tubing and some CNC'd flanges, but I seem to have lost a large amount of the files when I uninstalled AutoCAD. If you're going to be doing the CAD work yourself and you want some flow analysis, I have access to ANSYS at school and SolidWorks Flowxpres at work.
tooterThread starterLos Angeles · Mar 7, 2013#1095
Originally Posted by CrankyOldMan ↑
Aah yes, the old "under-utilized engineer" syndrome: if you don't give them problems to solve, they start making up their own.

I had also played with some ideas for a new plenum involving 6" aluminum tubing and some CNC'd flanges, but I seem to have lost a large amount of the files when I uninstalled AutoCAD. If you're going to be doing the CAD work yourself and you want some flow analysis, I have access to ANSYS at school and SolidWorks Flowxpres at work.
Thanks for the offer Cranky... 👍
But I leave that to the CNC guys. We go over the design details and they render them into a 3D visual, and then into xyz coordinates that tell the milling heads exactly where to go. The really nice thing is that the design office and the machine are all in one location.
tooterThread starterLos Angeles · Mar 7, 2013#1096
Originally Posted by malibuguy ↑
I thought about recreating the plenum when I go to do mine...just because the factory is so damn ugly. But I wonder if a larger volume could benift even more?
I unolcked some secrets in that "ugly" plenum... 😉

Picture not included in this copy

There's a "reverse velocity stack" which extends into the center of that really small plenum.

And I noticed something else... even though the picture doesn't show it, nothing is at right angles or parellel to the plane of the runner entrances. Everyhing is cocked at odd angles including that velocity stack.

Now this could likely be for noise reduction as that seems to be a major consideration in passenger vehicles, or it could be to break up resonant harmonic frequences so as to smooth out the peaks and valleys in the power band over a wide rpm range. There is almost no information on the web about these intake manifold issues, so I'm going to go off in a direction which I think will work.

Because that's what life's all about...

...finding out. 🙂
JustDidItUnited States · Mar 7, 2013#1097
Originally Posted by tooter ↑
Because that's what life's all about...

...finding out. 🙂
👍
CrankyOldManWest Michigan · Mar 9, 2013#1098
I managed to re-install inventor and get my project back. Here's a crude 3D pdf of a concept assembly. It's rather machine-intensive for the lower flange, so it would really need to be CNC'd, but the upper part could probably be done manually.

If you look at the bottom (four-barrel) end, you can see that the inserts are all a little different depth. This is to allow the entire existing plenum to be cut off and still retain the same relative tube length when mating to the 1NZ cylinder pitch.

1 attachment not included in this copy

tooterThread starterLos Angeles · Mar 9, 2013#1099
I'm going with a different concept that retains the existing rounded square base...


Picture not included in this copy
...to save the most costly and complex task of machining the 4 runner entrances. I already have some 6 inch tubing left over from the velocity stack spacer, and might use that. Although the other end will be something different if I can get a hold of the right materials.

Picture not included in this copy
CrankyOldManWest Michigan · Mar 9, 2013#1100
I had contemplated that, but then I would have to figure out how to weld up a rounded-square body. My idea was to match the radius of the base with some tubing, cut it into quarters, and weld panels between them. Given my lack of welding skill but substantial access to machining equipment, the tube + flanges seemed to make the most sense. It would still require someone to weld the seams, but tube-in-a-hole is easier than plates-hanging-in-space.