Replies continued
tooterThread starterLos Angeles · Jan 7, 2013#9511ZZ throttle body came in today... 🙂
Picture not included in this copy
...so it's off to the workshop to strip it and bead blast it to make it look like new. 🙂
suckerfaceMilwaukee, WI · Jan 7, 2013#952What part number on the TB?
Nevermind, just saw your post that it's a 030. That's good. Should be plug and play. The only issue I had with mine was some high idling at cold start, but calmed down quickly and didn't throw any CELs. If you got the 031, then you'd need to do a chip swap and adjust the idle screw.
Just remember to reset your ECU!
tooterThread starterLos Angeles · Jan 7, 2013#953 Originally Posted by
suckerface ↑ What part number on the TB?
Nevermind, just saw your post that it's a 030. That's good. Should be plug and play. The only issue I had with mine was some high idling at cold start, but calmed down quickly and didn't throw any CELs. If you got the 031, then you'd need to do a chip swap and adjust the idle screw.
Just remember to reset your ECU!
Wow, thanks for the heads up! 🙂
I had already drilled out the rivets for the chip swap, although it turned out fine as I was able to clean out the area where the gears are. I'm searching out some little nuts and bolts to put the chip back on, and other than that, it's all ready to go... 👍
Picture not included in this copy I really like how the micro stainless steel beads don't abraid away the metal surfaces or alter their dimensions, but act like tiny ball peen hammers that pound the surfaces to clean and smooth them out.
tooterThread starterLos Angeles · Jan 7, 2013#954Not wanting to leave anything to chance, I also chipped out the epoxy from the idle adjustment screw just in case I needed to tweak it...
Picture not included in this copy
The chip is bolted back on now, so next is step is installation... 🙂
Picture not included in this copy
tooterThread starterLos Angeles · Jan 7, 2013#955Already ran into a snag... 😕
The throttle body bore diameter of the Corolla throttle body is 55mm and not 51 mm. I'm still going to run it, and flared out the adapter with a Dremel and reblasted it to accept the larger diameter...
Picture not included in this copy
So my question for anyone here who knows... are all of the Corolla throttle bodies 55mm and not 51mm?
CTScottUSA, CT · Jan 7, 2013#956 Originally Posted by
tooter ↑ Already ran into a snag... 😕
The throttle body bore diameter of the Corolla throttle body is 55mm and not 51 mm. I'm still going to run it, and flared out the adapter with a Dremel and reblasted it to accept the larger diameter...
So my question for anyone here who knows... are all of the Corolla throttle bodies 55mm and not 51mm?
On 1ZZ Corollas the butterfly is 55mm in diameter
tooterThread starterLos Angeles · Jan 7, 2013#957It's on... 🙂
Picture not included in this copy
Now I need to make up an intake that will fit the larger bore.
Ediit: Just started it up... Jesus, the engine went nuts! The computer was all over the place wondering what to do. I just let it keep trying to figure out what the hell is going on hoping that it would learn the new idling parameters. It's still idling after about 10 minutes and is down to 900. And when you turn the lights on, it jumps up to 1,100. So it's going to need the idle screw turned down. Now I'm glad I chipped it out so that I don'n need to take off the throttle body.
Ran out of daylight, so I'm going to take it for a test run and call it a day.
Came back from the test run... plug and play my ass! 😆
The 030 throttle body has every single one of the problems that have ever been described.
High idle
Hanging throttle position.
Erratic high rpms
Rough jerking back and forth between throttle and decel.
I was damn lucky just to make it back home in one piece. Almost hit a car in traffic. l let off the throttle expecting the car to slow down and it decides to do one of those sudden 3,000 rpm accelerations while wondering what to do.
Bottom line... runs liks shit. 👎
CrankyOldManWest Michigan · Jan 7, 2013#958Where did you get 51mm from? I'm looking at my flange template and the mating bore diameter is 56mm. I'm thinking that the butterfly itself is 51?
tooterThread starterLos Angeles · Jan 7, 2013#959Here's a comparison between the two bodies...
Picture not included in this copy
...and the intake I cobbled together to fit the larger one...
Picture not included in this copy
tooterThread starterLos Angeles · Jan 7, 2013#960 Originally Posted by
CrankyOldMan ↑ Where did you get 51mm from? I'm looking at my flange template and the mating bore diameter is 56mm. I'm thinking that the butterfly itself is 51?
Hey Cranky, 🙂
51mm is the bore of the Corolla intake manifold. My guess is that Toyota must have gone to a 55mm bore throttle body when they changed to the plastic manifolds.
The 55mm throttle body fits fine and there are no butterfly clearance issues because the perimeter of the bore is only 2mm smaller, but this is still an issue I need to resolve. There's plenty of space to flare the adaptor out to 55mm I already did a quickie on one with a Dremel.
Greg
JustDidItUnited States · Jan 7, 2013#961awesome update!
dragoonmcIllinois · Jan 7, 2013#962that looks awesome!
tk-421Dagobah · Jan 7, 2013#96355mm sounds about right. I made this exact mod a couple of years ago and I've had zero problems. I do have a high idle, but there's nothing I can do about that, since the idle screw has some epoxy on top of it. Ah well. 🤷
That erratic behavior should go away after a couple of trips (at least it did in my case).
Bluevitz-rsOshawa, Ontario, Canada · Jan 7, 2013#964Mabey something got messed up on disassembly/re-assembly?
suckerfaceMilwaukee, WI · Jan 7, 2013#965 Originally Posted by
Bluevitz-rs ↑ Mabey something got messed up on disassembly/re-assembly?
This. Astroman and myself aren't the only ones to have plug and play success. I'm guessing something went awry when you started the chip swap drilling and pulled the epoxy off the idle screw.
It took a good 10-15 min for my yaris to calm down at first, then a few minutes the next couple starts. Within a few days, it'd idle high for about 90 seconds when I first started the car. Drove it like that for about a year until the wreck. Didn't touch a thing on the TB except with some degreaser to clean it up.
Also ran it with an SRI. Regular tubing size, just used a section of silicone tubing as a makeshift adapter. I'll try to find you my pics if you want to compare.
tooterThread starterLos Angeles · Jan 8, 2013#966 Originally Posted by
Bluevitz-rs ↑ Mabey something got messed up on disassembly/re-assembly?
Nope. I was super careful having read what everyone else did. Even picked out the epoxy real careful. The idle screw underneath is absolutely pristine...
Picture not included in this copy I'm going to give it a couple of cycles, just to see if anything gets better. I'm for sure going to swap out the chips to get rid of that really irritating delayed throttle notch between light throttle and decel. The chip behaves as if it was made to control the throttle for an automatic transmission as likely the majority of them were.
Funny, if the 030 was supposed to be the good one. Makes me wonder what an 031 was like? 😆
suckerfaceMilwaukee, WI · Jan 8, 2013#967Might be a stupid question, but you confirmed on the part itself that's it's the proper part number?
tooterThread starterLos Angeles · Jan 8, 2013#968Yes. The number is clearly printed on the chip. The throttle body itself is in excellent condition, and nothing on it had been buggered around with. I'm going to cycle it some more before I swap the chip, just to see if things get any better and I'm definitely going to turn the idle down! 😉
cali yarisCanoga Park, CA · Jan 8, 2013#969No one listens to me. I sold at least five pre-swapped TB's and none of my customers had issues. Swap the chip.
tooterThread starterLos Angeles · Jan 8, 2013#970 Originally Posted by TOLMACH ↑
Tooter, interesting projst.. thanks for the update
Quesition: you were able to re-use the pins that came with the original TB in your adaptor/new TB setup?
Thanks
Yes. 🙂
The holes are threaded to accept the stock studs.
tooterThread starterLos Angeles · Jan 8, 2013#971 Originally Posted by
cali yaris ↑ No one listens to me. I sold at least five pre-swapped TB's and none of my customers had issues. Swap the chip.
Got it, Garm. 🙂
bladesmith6PA · Jan 9, 2013#972I swapped the chip on the tb I had and still had issues. The high idle finally came down a bit but when you let off the pedal to decel the car got kind of herky-jerky(bucked) I finally took it off because of that. You could feel that the acceleration was better though....
tooterThread starterLos Angeles · Jan 9, 2013#973 Originally Posted by
bladesmith6 ↑ I swapped the chip on the tb I had and still had issues. The high idle finally came down a bit but when you let off the pedal to decel the car got kind of herky-jerky(bucked) I finally took it off because of that. You could feel that the acceleration was better though....
I hear ya on the bucking... it's flat out undriveable.
I'm swapping out the chip right now and am going to also turn down the idle, and will see what happens.
tooterThread starterLos Angeles · Jan 9, 2013#974 Originally Posted by
cali yaris ↑ No one listens to me. I sold at least five pre-swapped TB's and none of my customers had issues. Swap the chip.
Hey Garm, 🙂
Swapped out the chips and the throttle body does work a little bit better. It only goes to 2,000 now while suddenly deciding to hunt around for an idle speed. And it still has that 2 second delayed jerky drop on decel that makes the drivetrain shudder. I did turn the idle down 1/4 turn. It needs more, but at least I can do something about that issue.
Driving at speed is strange, you just rest your big toe on the accelerator and it holds 40 mph Even partial throttle and the engine is eagerly accelerating. Clearly this thing is capable of feeding
lots of air into the engine without hardly any angle on the butterfly. This makes the throttle extremely sensitive. Now that's not a complaint as it's not so much so as to be unsafe. It will just take some driving to get used to it.
All in all, at least some improvement. Do you have any other ideas? Particularly about the two second delay of the jerk on decel. If I just barely have the throttle pressed, the jerking cycles back and forth constantly. It feels like it has lost the ability to smoothly transition from throttle to decel, and the delay tells me that it is computer related because it is so perfectly evenly timed.
Even running both chips the throttle body has never thrown a CEL light... so at least that's good.
Greg
Bluevitz-rsOshawa, Ontario, Canada · Jan 9, 2013#975If you remember the old fashioned fueling devices called a carburetor, they had a device called a dashpot that holds the throttle partially open while you release the pedal and acts as an emission control device. The computer treats the electronic throttle the same way. But because the throttle is larger the effect is greater.
Picture not included in this copy
tooterThread starterLos Angeles · Jan 9, 2013#976 Originally Posted by TOLMACH ↑
Thanks
Have not yet received my adaptor.. but I am sure it is totally awesome ))
Wow... it's been 7 days since it was mailed. How long does it take stuff to go through customs? The Customs Declaration number is:
LC892190662US
It's a Small Flat Rate Priority Mail Box. See if they can locate it.
Greg
tooterThread starterLos Angeles · Jan 9, 2013#977 Originally Posted by
Bluevitz-rs ↑ If you remember the old fashioned fueling devices called a carburetor, they had a device called a dashpot that holds the throttle partially open while you release the pedal and acts as an emission control device. The computer treats the electronic throttle the same way. But because the throttle is larger the effect is greater.
Picture not included in this copy
Yeah, I'm familiar with those, because I'm from that era. 😉
...but they let the throttle down slowly and smoothly. This waits 2 seconds and then suddenly drops it shut. This is a precise computer timed event as it does it exactly the same each time.
So this brings me back around to the same question:
Has anyone here ever
successfully run a Corolla throttle body with
none of the issues I'm experiencing?
bladesmith6PA · Jan 9, 2013#978You know i was thinking about this , this might be the case where one of those aftermarket throttle controllers is just the thing. You have to calibrate them when you plug it in between the accel pedal and the obd II port anyway, it might correct the bucking issue...
tooterThread starterLos Angeles · Jan 9, 2013#979Now that's an intriguing idea. 🙂
Does anyone here run a throttle controller that they can program for instant deceleration?
CrankyOldManWest Michigan · Jan 10, 2013#980From what I remember reading in other TB swap threads, you need to let the ECU completely reset between idle screw adjustments--i.e. unplug the battery for at least a few minutes. In theory, that will help with the idle RPM hunting.
suckerfaceMilwaukee, WI · Jan 10, 2013#981 Originally Posted by
tooter ↑ Has anyone here ever successfully run a Corolla throttle body with none of the issues I'm experiencing?
As mentioned, aside from the fluctuating idle at cold start (which only lasted 1-2 minutes) I had ZERO problems with mine. Also had an SRI on it. Same part number as yours, just cleaned it up and slapped it on. No chip swap. Didn't even clean the epoxy off the idle screw.
I'll do some digging to see if I ever did a video of it.
CTScottUSA, CT · Jan 10, 2013#982Tooter has a 2012, which has an entirely new ECM, so there may be some differences in how the ECM reacts to changing the throttle controller.
tooterThread starterLos Angeles · Jan 10, 2013#983I'll still try Cranky's advice (Thanks! 🙂) of resetting between each idle change. I'm really going to crank it down today, because regardless of any of the other issues, it idles too fast. I was thinking that maybe the ECU keeps fishing around for the right idle speed, because the butterfly is prevented from closing enough to acheive it.
tooterThread starterLos Angeles · Jan 10, 2013#984 Originally Posted by
suckerface ↑ As mentioned, aside from the fluctuating idle at cold start (which only lasted 1-2 minutes) I had ZERO problems with mine. Also had an SRI on it. Same part number as yours, just cleaned it up and slapped it on. No chip swap. Didn't even clean the epoxy off the idle screw.
I'll do some digging to see if I ever did a video of it.
I'm glad to hear that,sucker... 🙂
At least it worked right for one person here. I'm also glad it worked with your SRI so I can rule out that variable on mine. I can say that when you step on the gas... man, it
roars! Picture not included in this copy The noise could be deceptively making the car feel like it's faster, but the dyno will provide an objective answer that.
Even if all of the issues aren't sorted out, when I get the ECU to a stable point, I'm taking it down to Harry's dyno shop! 👍
Greg
Bluevitz-rsOshawa, Ontario, Canada · Jan 10, 2013#985I don't remember if it was asked at all, but does this manifold sit any closer to the rad than the plastic one?
tooterThread starterLos Angeles · Jan 10, 2013#986 Originally Posted by
Bluevitz-rs ↑ I don't remember if it was asked at all, but does this manifold sit any closer to the rad than the plastic one?
Just measured. The minimum distance between the tooter and the plastic radiator reservoir is 30mm. This is the the point where it comes closest to the radiator assembly. It's not nearly as compact as the stock manifold because the runners are larger diameter and curve around a lot so that they will all end up being exactly the same length.
Picture not included in this copy tooterThread starterLos Angeles · Jan 10, 2013#987It was the IDLE. 🙂
This morning, I cranked the screw out one full turn and did a cold start. Didn't even reset the ECU. NO CEL light. Totally normal start. No racing idle. No hunting for idle speed. Perfectly normal warm up idle. Totally normal hot idle. No surging. No sudden shuddering notch from slight throttle to decel...
...and the throttle response is SUPERB.
(oooh, goody 🙂 )
So the problem was that the ECU couldn't function properly because the butterfly was being physically prevented from being closed enough by the idle screw which was factory set for a 1.8 and not a 1.5.
I can't tell you how happy this makes me to have found out how to instantly solve all of the problems with just one simple procedure.
It was really dicey breaking loose the idle adjustment screw without stripping it. I used a fractional inch hex key as it was slightly larger than the metric one, and applied Liquid wrench to the threads. Then I put in the hex key and tapped it with a mallot. It turned really hard right at first and then was much easier as the oil penetrated the threads. Now it twiddles without being loose. I'm going to set it with silicone so that if I ever need to readjust it, the silicone plug can be removed easily. 👍
Dyno shop, here I come! 🙂
WeeYariGeorgetown, Ontario, Canada · Jan 10, 2013#988🍻
Bluevitz-rsOshawa, Ontario, Canada · Jan 10, 2013#989 Originally Posted by
tooter ↑ Just measured. The minimum distance between the tooter and the plastic radiator reservoir is 30mm. This is the the point where it comes closest to the radiator assembly. It's not nearly as compact as the stock manifold because the runners are larger diameter and curve around a lot so that they will all end up being exactly the same length.
How much less room compared to the plastic manifold? Just asking because the Echo doesn't have a lot of space between it and the rad.
tooterThread starterLos Angeles · Jan 10, 2013#990 Originally Posted by
Bluevitz-rs ↑ How much less room compared to the plastic manifold? Just asking because the Echo doesn't have a lot of space between it and the rad.
A
lot less...
The overall depth of the plastic stock manifold is only 130mm, while the depth of the tooter is 210mm.
tooterThread starterLos Angeles · Jan 10, 2013#991I combined the Simota intake tube with the BLOX velocity stack because the Simota is larger in diameter which matches the larger diameter of the Corolla throttle body throat...
Picture not included in this copy
Now no adaptor coupling is needed, as everything is all the same size straight through from the velocity stack to the throttle body... 🙂
Picture not included in this copy
Notice the throttle body?... you'd never know that was an 8 year old junkyard part. Stainless steel micro bead blasting makes the old casting look like it's brand new.
I think I'll go for a ride now. 😁
discomark10Bucks · Jan 10, 2013#992Glad to hear you got it running sweet!
cant wait for the dyno! 😲
suckerfaceMilwaukee, WI · Jan 10, 2013#993That's awesome you got it all straightened out. I wanted to adjust the idle screw on mine, but it didn't bother me enough to go out of my way to take the time to do it. Now I kind of wish I had...however, I agree, the throttle response is AMAZING! My fiance, who used to have a Yaris, even commented on the difference it makes!
Can't wait to see what the dyno puts down for you!
tooterThread starterLos Angeles · Jan 10, 2013#994 Originally Posted by
suckerface ↑ That's awesome you got it all straightened out. I wanted to adjust the idle screw on mine, but it didn't bother me enough to go out of my way to take the time to do it. Now I kind of wish I had...however, I agree, the throttle response is AMAZING! My fiance, who used to have a Yaris, even commented on the difference it makes!
Just came back from running errands in town, and the engine runs
so GOOD. 🙂
I can't believe that it works so much
better than the stock throttle body. Especially in low rpm response. You barely touch the pedal and the car is right up to speed. Haven't taken it on the freeway yet, but I'll do that tomorrow. It's all gassed up and ready to take mileage readings.
Can't wait to see what the dyno puts down for you!
Neither can I. I'm so excited! 🙂
Now the 1.8 throttle body matches the 1.8 manifold as well as the oversized SRI. 👍
tooterThread starterLos Angeles · Jan 10, 2013#995 Originally Posted by
4/20 NEVER FORGET ↑ You're killing me here, man. You've come so far that not sourcing a 1ZZ TB and dynoing it seems weird to me, like you're aborting the project early. You even had the TB adapter made to match the 1ZZ throttle body, yet you aren't going to at least try and get one?
THANK YOU! 🙇 JustDidItUnited States · Jan 10, 2013#996 Originally Posted by
4/20 NEVER FORGET ↑ You're killing me here, man. You've come so far that not sourcing a 1ZZ TB and dynoing it seems weird to me, like you're aborting the project early. You even had the TB adapter made to match the 1ZZ throttle body, yet you aren't going to at least try and get one?
Originally Posted by
tooter ↑ THANK YOU! 🙇
Awesome read!
4/20 NEVER FORGETPortland, OR · Jan 11, 2013#997 Originally Posted by
tooter ↑ THANK YOU! 🙇
No dude, THANK YOU!!! I am so happy you got it running good finally, and that there seems to be a noticeable difference. Looking at the two throttle bodies side by side, you would think there would have to be. The stock TB is so small!
Anyways, this has been a great thread to follow, and I know I can speak for the entire community when I say thanks for posting so often and clearly about the issues and wins you have been having. These threads help us all out. Again, congrats, and I can't wait to see what this sucker does on the dyno. Please post a vid with audio! I bet she screams!
👍👍👍👍👍
jetblastNor Cal · Jan 11, 2013#998Staring at pic............................................... .................................................. .................................................. .................................................. .................................................. .................................................. ...........still staring at pic............................................... .................................................. .................................................. .................................................. .......damn nice.............................................. .................................................. .................................................. .................................................. .......still staring.🎉
tooterThread starterLos Angeles · Jan 11, 2013#999 Originally Posted by
4/20 NEVER FORGET ↑ No dude, THANK YOU!!! I am so happy you got it running good finally, and that there seems to be a noticeable difference. Looking at the two throttle bodies side by side, you would think there would have to be. The stock TB is so small!
Anyways, this has been a great thread to follow, and I know I can speak for the entire community when I say thanks for posting so often and clearly about the issues and wins you have been having. These threads help us all out. Again, congrats, and I can't wait to see what this sucker does on the dyno. Please post a vid with audio! I bet she screams!
👍👍👍👍👍
Hey man, thanks for the kind words... 🙂
From this experience I'm pretty certain that the chips don't even need to be swapped. The butterfly just needs to close farther so that the ECU can find the right idle. Because when I ran both chips, both had the
same symptoms. Reducing the idle speed
alone is what resolved
all of the issues.
So in the future...
If anyone wants to install a part number 030 Corolla 1ZZ throttle body on their 1NZ engine, don't mess with the chips, and simply turn the idle down by backing out the little idle adjustment screw counterclockwise one turn using a 5/64th inch hex key... and everything should work just fine.👍
I did quite a bit of driving today on the freeway and in traffic with shopping and running errands, and I'm so thoroughly pleased with how well the engine responds with the bigger throttle body.
It behaves like a completely different car! 🙂
JustDidItUnited States · Jan 11, 2013#1000 Originally Posted by
tooter ↑ If anyone wants to install a part number 030 Corolla 1ZZ throttle body on their 1NZ engine, don't mess with the chips, and simply turn the idle down by backing out the little idle adjustment screw counterclockwise one turn using a 5/64th inch hex key... and everything should work just fine.👍
Wonder if this works on my 1NZ-FXE....
Picture not included in this copy