Yarisworld Archive

SQcomps install

403 posts · 83,895 views · page 6 of 9

Replies continued

sqcompBack at home · Jul 15, 2010#252
*
derickveliz2Central, MA · Jul 15, 2010#253
Sounds like a lot! and I'm 1000+ miles behind you.

Good job!
sqcompBack at home · Jul 15, 2010#254
Update on the scoping of the P-01...

Off the RCAs into the amps we run 6.3 Volts of unbalanced signal maxed out at 1kHz. There's something interesting I'm seeing though. The higher I go up the lower the voltage. All my EQs are flat, T/A is off...everything is flatlined.

Now onto the gains...

It appears that at 4 Volts at the RCA the L4 is seeing 127 Watts on both sides at "max". I want to set the levels at 4 Volts because of the possibility of EQ boost at top end that I might want. What I'm seeing is that the deck likes to taper the voltage off slightly on both ends (bass and tweeter ranges). At full tilt boogie (volume 62) at the 6.3 volts the ends drop around .5 to 1 Volt on either end. When I lower the volume to 60 it is a little over 4 Volts on a 1 kHz tone. I figure this is safe to set the gains to...

The L1 Pro SEs are seeing 114 Watts at 4 Volts with an 8 kHz tone at my "max"...

The ML3800 is seeing 823 watts at 4 Volts with a 40 Hz tone at my "max"...

I was really hoping for a deck that would be even with it's Voltage output. What I'm hearing from the shop owner is that this isn't uncommon though. He said he sees this in a lot of high Voltage decks.
sqcompBack at home · Jul 15, 2010#255
*
derickveliz2Central, MA · Jul 16, 2010#256
.
Sqcomp... and others what do you guys think about "Diffractions" at mid-range and tweeters?

D.
sqcompBack at home · Jul 16, 2010#257
*
derickveliz2Central, MA · Jul 16, 2010#258


I found this, and thought it was interesting but don't know how much of attention it's getting from professionals.


LINK to Diffractions

.
sqcompBack at home · Jul 16, 2010#259
*
sqcompBack at home · Jul 16, 2010#260
*
sqcompBack at home · Jul 21, 2010#261
*
bzinn 1University Place,WA · Jul 21, 2010#262
I like over kill......honestly it makes for a better install to keep it all nice and neat,and if you have to remove it is also not a pain to do so.....looks great man
FcukThisseattle · Jul 23, 2010#263
jeeeebus christ, you're running some very very sexy stuff.
sqcompBack at home · Jul 23, 2010#264
*
FcukThisseattle · Jul 23, 2010#265
Threads like these are the very reason why i got into installs in the first place.

I can't wait till you finish, it's going to be killer. You'll definitely pull in trophies, especially with that kind of attention to the smallest of details.

Wish you lived in the Seattle area, *tear* it's just so beautiful. Really wish i had you around when i was starting my install. Definitely something you're going to be proud of for the rest of your life.
sqcompBack at home · Jul 23, 2010#266
*
talnlnkyThread starterSpokane, Wa · Jul 24, 2010#267
Originally Posted by FcukThis ↑
Really wish i had you around when i was starting my install. Definitely something you're going to be proud of for the rest of your life.
OH NO!... I got dibs on John, been trying to sweetly convince him to help me out for the past year.
sqcompBack at home · Jul 24, 2010#268
*
talnlnkyThread starterSpokane, Wa · Jul 24, 2010#269
Originally Posted by sqcomp ↑
That's good. "sweetly convince", something like that. I just have to get down to your area. With that being said, as soon as this house deal comes through, I'll be in Sherwood...and have an excuse to take a trip down your way. You have a couch I can crash on? We could work on the Yaris for the weekend. I warn you though, you MUST have a grill, cause I like to throw steaks on after working on systems.
dude, i'm moving to Dexter (highway 58 near creswell) and will have a garage for the first time in 2 years. Single car/bay but oh well, its a garage. Yes, we have a lil weber grill, and its capable of doing steaks, just tuesday I cooked my first steak ever on it... wasn't bad, though I should've flipped the thing a bit sooner. The place will have 2 big bedrooms and a living room, we just craigslisted a loveseat/couch combo yesterday that will go nice. One of the bedrooms will be come the study/HT room.

I'd love to get some work done on it next spring once I get back from DPSST.
sqcompBack at home · Jul 24, 2010#270
*
talnlnkyThread starterSpokane, Wa · Jul 25, 2010#271
Originally Posted by sqcomp ↑
That's a few miles SE of Eugene isn't it? We'll make it a plan. No worries. My wife will be happy to get rid of me for a weekend I'm sure. Are we going to be doing some fab on the component mounting?
Yeah, SE of Eugene by about 20 mins. If/when you head out this way, fabing either pilar pods for the mids & tweets would be what i'd prefer to do.. but doing a lil midbass install would work too. Pods for the mids & tweets is what i'd need assistance with most tho.
sqcompBack at home · Jul 26, 2010#272
*
derickveliz2Central, MA · Jul 27, 2010#273
.

Sqcomp... you need to blow away all that dust... or turn on the volume and blast the dust away!

The HAT speakers look awesome!

.
sqcompBack at home · Jul 27, 2010#274
*
talnlnkyThread starterSpokane, Wa · Jul 28, 2010#275
looks good. I love the look of resin'd grill cloth and body filler.
sqcompBack at home · Aug 1, 2010#276
*
derickveliz2Central, MA · Aug 1, 2010#277
Originally Posted by sqcomp ↑
*bah*
Then life is good and moving on to the trunk's finishwork and some RTA work.
What does RTA means?

(o:
talnlnkyThread starterSpokane, Wa · Aug 1, 2010#278
Originally Posted by derickveliz2 ↑
What does RTA means?

(o:
Real Time Analyzer... basically its just a tool that will show him the frequency response inside his car... its one thing to design a flat response on a computer... its another thing to put speakers in a funky shaped space (like a car) with reflective surfaces and get a flat response.

Once he runs a slow sine sweep from 20khz down to 20hz with the microphone around head rest level he'll have a decent idea of what frequencies he's missing, and which are way too strong... from there he can use his eq to cut the strong frequencies, and boost the weak ones.

It is generally a good idea to focus mostly on cutting, than on boosting due to issues with clipping, and the fact that it is easier to tell a speaker to play something softer than to work harder.


Another thing... a flat response would sound boring and lacking bass for most people...so he may end up eq'ing for something other than a flat response... like a response that slightly increases as it drops below 200hz.

i've never had an rta... but it would be a fun tool to play with... i'll put it on the list of toys along with the O scope, signal generator, and clamp meter (amp-meter)
derickveliz2Central, MA · Aug 2, 2010#279
Originally Posted by talnlnky ↑
Real Time Analyzer... basically its just a tool that will show him the frequency response inside his car... its one thing to design a flat response on a computer... its another thing to put speakers in a funky shaped space (like a car) with reflective surfaces and get a flat response.
Once he runs a slow sine sweep from 20khz down to 20hz with the microphone around head rest level he'll have a decent idea of what frequencies he's missing, and which are way too strong... from there he can use his eq to cut the strong frequencies, and boost the weak ones.
It is generally a good idea to focus mostly on cutting, than on boosting due to issues with clipping, and the fact that it is easier to tell a speaker to play something softer than to work harder.
Another thing... a flat response would sound boring and lacking bass for most people...so he may end up eq'ing for something other than a flat response... like a response that slightly increases as it drops below 200hz.
i've never had an rta... but it would be a fun tool to play with... i'll put it on the list of toys along with the O scope, signal generator, and clamp meter (amp-meter)


Thanks Talnlnky there is so much to learn,

D.
sqcompBack at home · Aug 2, 2010#280
*
sqcompBack at home · Aug 4, 2010#281
*
sqcompBack at home · Aug 5, 2010#282
*
sqcompBack at home · Aug 5, 2010#283
*
derickveliz2Central, MA · Aug 6, 2010#284
.

That's AWESOME!!!

are you going to cover the 4" drivers?

Derick
talnlnkyThread starterSpokane, Wa · Aug 6, 2010#285
props for using spanner screws.
sqcompBack at home · Aug 6, 2010#286
*
talnlnkyThread starterSpokane, Wa · Aug 16, 2010#287
updates john? i haven't been on for a week and yet I don't see anything new from you for the past 10 days.... you run out of steam or time?
sqcompBack at home · Aug 17, 2010#288
*
sqcompBack at home · Aug 18, 2010#289
*
DailyDriverutah · Aug 21, 2010#290
those speaker mounts are so clean on the pillars... wow! i've never done any glassing, but i know if i did it wouldn't end up looking like that. N-I-C-E.
derickveliz2Central, MA · Aug 21, 2010#291
Originally Posted by DailyDriver ↑
those speaker mounts are so clean on the pillars... wow! i've never done any glassing, but i know if i did it wouldn't end up looking like that. N-I-C-E.
I agree %500!!!

>
sqcompBack at home · Aug 21, 2010#292
*
_S7V7N_South Texas · Aug 21, 2010#293
Dayumnnn Your car is looking kicka$$, Nice work bro👍
sqcompBack at home · Aug 22, 2010#294
*
sqcompBack at home · Aug 30, 2010#295
*
Alien MantisArizona · Aug 30, 2010#296
After reading what you wrote about the gain settings, I thought of a question.

How do the judges "judge" your car? Do they use any test equipment? Do they just listen to your system and try and "think" about how it sounds? Do they crank it up to a specific SPL and then judge it's overall clarity? Do they measure / judge it's ability to reproduce sounds accurately in different frequency ranges? Do they play their own test-source material in all the cars, or can the competitor pick his own music/source media?
Do the judges get in the car, and close the doors, or do they listen / measure from different test locations in and around the vehicle?

Just curious, since I have never been to a SQ competition before.

ALSO:
You could grow old waiting for that LRx amp.
Is that the one you are powering the sub with?

Just get a JL Audio or one of them new High-End Alpine's and finish that sucker!
At least you can finish tuning your system, and go to some competitions.
You know you don't need to be all that picky with your SUB amp.
The SUB is somewhat forgiving.

Two years later when you get your LRx, you can swap it out and see if it actually made any difference.

😁
sqcompBack at home · Aug 31, 2010#298
*
Alien MantisArizona · Aug 31, 2010#299
Ok, thanks for the reply.

So your dead amp was your mid-bass.
How do you control the freq's to your mid-bass drivers?
I would think you would want a narrow range on them. Something like 80hz-250hz.
Then you could let your SUB take everything below 80hz, and your mids can have everything above 250hz until the tweeter takes over at maybe 6k-ish?

I see sub amps have an LPF crossover, but nothing that would allow me to cut the low bass at 80hz. Some have a subsonic filter, but these are usually around 15-30hz.

So how do you only send those mid-bass freq's to the mid-bass drivers?
( You are probably going to tell me your Carrozeria HU can do it. )

A high-end vented 15" is an earthquake machine.
More SUB than most cars ever need.
MTX 9500 series.
But I know you like your fancy boutique stuff.

Audison Thesis is probably the best stuff I know about.
I have no idea what is better than the Thesis stuff.
All that stuff is so unbelievably expensive, at that level, it doesn't even matter.
I think all the higher-end consumer stuff is too expensive.

I think $500 for a single AMP is too much.
😢

I think if you spend more money on the audio system, than what the car is worth, you FAILED!

😁

But I see it all the time. Dudes rolling around in POS cars, with thousands of dollars worth of audio gear in them. Ghetto rats.
Everytime their generic 12's hit a beat, the whole car rattles.
Two 12" BOSS subs in a bandpass box in the trunk = FAIL

Of course, if you are competing, and that is your hobby, then that is a whole different story.
( or maybe it's your career )
derickveliz2Central, MA · Sep 1, 2010#300
Originally Posted by Alien Mantis ↑
So your dead amp was your mid-bass.
How do you control the freq's to your mid-bass drivers?
I would think you would want a narrow range on them. Something like 80hz-250hz.
Then you could let your SUB take everything below 80hz, and your mids can have everything above 250hz until the tweeter takes over at maybe 3k-ish?

I see sub amps have an LPF crossover, but nothing that would allow me to cut the low bass at 80hz. Some have a subsonic filter, but these are usually around 15-30hz.

So how do you only send those mid-bass freq's to the mid-bass drivers?
( You are probably going to tell me your Carrozeria HU can do it. )
Yeah! 🙇 that's the beauty of the Carrozeria AKA P-99 that I've been talking about, the HU has o watts for speakers but comes with 4 outputs:

Sub
Low
Mid
High


It's like heaven on earth controlling each individual speaker any way you want.

sqcomp can give you more details about these HU, I can only tell you that this is what I've been looking for all my life.👍

D.