Replies continued
CTScottUSA, CT · Apr 20, 2009#101Here's a comparison of SodiumDuck's 08 (left) and my 09 (right) (from when we installed our remote starters). Mine has the blue and brown, and his just has the black horn wire.
On the EWD, the spiral cable is just the block between 3B and 1A, as well as the block between 1C and 8A on the horn diagram on page 145. The spiral cable simply brings the signals off of the movable steering wheel. (If we had the European steering wheel controls, they would most likely connect through the last unused pin).
enobmort42Denver, CO · Apr 20, 2009#102i'm beginning to get lost in all the technical talk. i should probably take a look at mine up in there.. unless someone can tell me if i have what it takes to do this by telling them that i have an '07 lb hatch? 👍
CTScottUSA, CT · Apr 20, 2009#103I was thinking that I was having deja-vu on this topic and found this topic from a while back:
Cruise Control - Again! Out of curiosity, have you checked to see if your combination meter has the two cruise lights.
Sir A.Y. AtoyotSurrey, BC Canada · Apr 21, 2009#104No cruise light on my dash panel. It has a fog light icon, though (no actual fog lights in the car).
Canadian 2008 5-door hatch.
mikenacaratoBrentwood, TN · Apr 21, 2009#105ah so since the cruise connects to the inside of the oem steerig wheel looks like i cant add it since i have an aftermarket wheel :(
Sir A.Y. AtoyotSurrey, BC Canada · Apr 21, 2009#106 Originally Posted by
mikenacarato ↑ ah so since the cruise connects to the inside of the oem steerig wheel looks like i cant add it since i have an aftermarket wheel :(
You could install one of the aftermarket Rostra brand units, which doesn't attach to the steering wheel. Be prepared to pay lots, though.
CTScottUSA, CT · Apr 21, 2009#107 Originally Posted by
Sir A.Y. Atoyot ↑ You could install one of the aftermarket Rostra brand units, which doesn't attach to the steering wheel. Be prepared to pay lots, though.
Or you could add four momentary switches (On/Off, Set, Up, Down) to the dash like I am going to do to save on buying the stalk and on having to pull the airbag.
Sir A.Y. AtoyotSurrey, BC Canada · Apr 21, 2009#108 Originally Posted by
CTScott ↑ Or you could add four momentary switches (On/Off, Set, Up, Down) to the dash like I am going to do to save on buying the stalk and on having to pull the airbag.
Good luck with that - those functions on the stock switch work through resistors and involve the extremely expensive central engine computer (ECM). The resistors are the squiggly lines in the diagram. It's important to know the exact values to make it work right. A familiarity with Ohm's Law would help, too.
CTScottUSA, CT · Apr 21, 2009#109 Originally Posted by
Sir A.Y. Atoyot ↑ Good luck with that - those functions on the stock switch work through resistors and involve the extremely expensive central engine computer (ECM). The resistors are the squiggly lines in the diagram. It's important to know the exact values to make it work right.
Correct. The resistor values are:
216 to 264 ohms for one between resume and on/off
351 to 426 ohms for the one between set and resume
819 to 1001 ohms for the one between set and cancel
This is a standard way of having multiple inputs on a single wire.
CTScottUSA, CT · Apr 21, 2009#110 Originally Posted by PK198105 ↑
you realize CTScott is an electrical engineer right😁 and Im a electrical engineering tech
BTW CTScott i was thinking the same thing about the switches except Im thinking of mounting them in my door armrest right above the handle, i will most likely canibalize the stalk and use jumper wires and a LED to show the status
I am soldering up a two button test rig right now. I have a Karate class at 8, so I am hoping to test on/off and Set on my way there...
CTScottUSA, CT · Apr 21, 2009#111OK. My two button rig is connected. When I turn the ignition on and press my on/off switch the speedometer icon lights up. Now to throw on my dobuk and hit the road for the road test...
IllusionXBrossard, QC · Apr 21, 2009#112PK: if you are going to make yourself a new set of switches... don't cannibalize your stalk... sell it to me :)
CTScottUSA, CT · Apr 21, 2009#113 Originally Posted by PK198105 ↑
so you connected it straight to D3?
Worked like a charm!
I used tap splices onto pins 1 (blue) and 3 (brown) of D3.
My test setup consisted of 2 feet of 2 conductor cable going to two parallel switches. The first is the On/Off switch which connects directly to the two wires. The second is the Set switch and has a 660 ohm resistor on the CCS line from the first to it.
Here's the combination meter in the garage with the ignition on and the on/off button pressed once:
Here's the meter with the Set button pressed at 35 MPH (and my foot off the gas):
The Set button doubles as the - button, so each press would drop the speed by one MPH. When I pressed the On/Off button while CC was on, it would drop the lights and decelerate until I put my foot on the gas. So, at this point I have free cruise control (from parts lying around my office).
Now I just have to find some switches that I like to button it up...
AlexNet0Rockland, ME · Apr 21, 2009#114thats awesome, you should make a step by step how-to with a link to the resistors to use, I would actually prefer this way
Sir A.Y. AtoyotSurrey, BC Canada · Apr 21, 2009#115Very tidy - congrats to CTScott on getting the first practical results out of this discussion.
I'm not an electrical engineer - just a licensed mechanic. I have an aversion to hacking into the wiring on a near-new car that's still on warranty, but I can see my way clear now to acquiring the necessary bits to do it right.
AlexNet0Rockland, ME · Apr 21, 2009#116 Originally Posted by PK198105 ↑
Alex check if you have the wires in D3 otherwise you will need jumper wires
Will do tomorrow
CTScottUSA, CT · Apr 21, 2009#117 Originally Posted by PK198105 ↑
great news, although i suspect that you have factory installed wire going to AD4 junction box.
my turn but only after my exams lol. which switched you plan on running.
Have you checked to see if there is a wire leaving pin 15 of connector AD4? If there is, then tapping there wouldn't be any worse than tapping D3. Also, you only need that one wire, as the other just needs to connect to any ground point.

CTScottUSA, CT · Apr 21, 2009#118 Originally Posted by PK198105 ↑
if you look on page 105 of the EWD it says pin 6 for the AD4 box from D3.
That's correct. I was looking at the wrong blue when I typed that. When Alex checks his D3 connector (where I am 90% sure he'll just see the lonely horn wire), he should then check Pin 6 of AD4 to see if there is a wire there.
CTScottUSA, CT · Apr 21, 2009#119 Originally Posted by PK198105 ↑
the only PITA is that the AD4 box is under the dash near the windshield. But why would he only have the Horn wire, whats different from your Yaris?🤷
did you get an extra option or what? The other thing is on mine i don't have the Cruise Icon, so i would need to McGyver a way to get a LED to light up when I turn on the cruise
I think that only 09 Liftbacks have the two additional wires in D3, as Sir A.Y. Atoyot's 08 didn't and neither did SodiumDuck's 08.
CTScottUSA, CT · Apr 22, 2009#120 Originally Posted by PK198105 ↑
cool, ill pop mine tomorrow and let you know if the 07 has it or not. how did you approximate the resistor values, because from the diagram the values given are for the total resistance , i.e each resistor adds to the other to create a final resistance depending on which switch is active. I.e cancel one takes all three resistors into consideration
The service manual gave resistance ranges from CCS to ground with each of the four switches pressed.
Resume picks up just the first resistor, so its resistor value is simply the value listed.
Set picks up the first two, so I subtracted the value for Resume from total resistance measurement with Set pressed to get the second value.
Cancel picks up all three, so I subtracted the value total resistance for Set from the total for Cancel to get the value of the third.
CTScottUSA, CT · Apr 22, 2009#121 Originally Posted by PK198105 ↑
ok thats logical , i wasn't sure about the 10k resistance when the switch is off. but i guess that's the "ECM impedance". so i guess we could use:
Standard values:
RES ---> 240Ohms
SET ---> 620Ohms
Cancel ---> 1600ohms
All these in 5% tolerance level or even 1%
NOTE: TO ALL ATTEMPTING THIS WAY MAKE SURE YOUR SWITCHES DO NOT HAVE A BUILT IN RESISTANCE OR THIS WILL CHANGE THE VALUE OF THE TOTAL RESISTANCE AND MAY CAUSE UNRELIABLE CRUISE CONTROL FUNCTION OR DAMAGE TO THE CSS PORT OF THE ECM
Those are correct if you wire the switches with the resistor in series with each. If you wire it per the stalk schematic they would be:
216 to 264 ohms for one between resume and on/off
351 to 426 ohms for the one between set and resume
819 to 1001 ohms for the one between set and cancel
By the way, you actually can't harm the EMC port with the wrong resistors, as the port can handle a direct short (as the on/off switch does) to infinite resistance (no buttons pressed).
CreeperGeorgia · Apr 22, 2009#122so with the switches option do we still have to take off the airbag or just the stearing column cover?
devinlamotheSudbury, Canada · Apr 22, 2009#123 Originally Posted by PK198105 ↑
The switches you will only need to take the steering column off and look for two wires from the D3 connector a blue one and a brown one. Now if you don't have these you will most likely need to attach at least one jumper wire to act as the OEM blue wire that goes from D3 to junction box AD4 which is located on the driver side near the windshield, thus you will have to take off the dash most likely (unless someone has an easier way of accessing this location)
Hopefully there is an easier way of getting there as I have no intention to take my whole dash off 😕
I am going to be putting a new headlight stalk on tomorrow so I will check my '07 liftback to see if the wires are there.
CreeperGeorgia · Apr 22, 2009#124ill have to look next time i work on my car. when my projectors get here... also gotta try to do easy fix on my back bumper :( anyway ill check my 07 hatch when i can..
CTScottUSA, CT · Apr 22, 2009#125 Originally Posted by PK198105 ↑
ok 07s do not have wires from D3 only the horn wire. i'm trying to find an easier way to tap into the AD4 box ill keep you posted.
It may just be easier to connect to the wire on the ECM instead of trying to get to AD4. The ECM connector is so easy to access under the hood and poking a wire through the giant firewall grommet under the dash is easy as well.
ShroomsterOrlando · Apr 22, 2009#126so have any of you even gotten the stalk to work yet? lol
ShroomsterOrlando · Apr 22, 2009#127 Originally Posted by PK198105 ↑
the stalk will work 100% , the problem is we will most likely need to use jumper wires to connect the rest of the system together , its not a big job but it needs to be done.
short answer...no, but in progress 😁
keep at it you guys....
mrbondThread starterIllinois · Apr 22, 2009#128I'd hope one of you would post a short DIY for connecting the jumper wires. With pictures :P
Have any of you received your stalks yet btw? I'm still waiting on mine, and the tracking number I was given wasn't valid :/
AlexNet0Rockland, ME · Apr 22, 2009#129 Originally Posted by
mrbond ↑ I'm still waiting on mine, and the tracking number I was given wasn't valid :/
+1
mrbondThread starterIllinois · Apr 22, 2009#130 Originally Posted by PK198105 ↑
it will probably be a team effort between CTScott and I for the DIY. Im off to dive under the dash to figure out a way to get to the AD4 (i swear its almost as well hidden as the Gspot 😁)
Lol, shouldn't be too hard to find then rofl
MGarganoNJ · Apr 22, 2009#131 Originally Posted by
mrbond ↑ I'd hope one of you would post a short DIY for connecting the jumper wires. With pictures :P
Have any of you received your stalks yet btw? I'm still waiting on mine, and the tracking number I was given wasn't valid :/
I had the same problem with the tracking number... weird.
CTScottUSA, CT · Apr 22, 2009#132devinlamotheSudbury, Canada · Apr 22, 2009#133OK so I get the dumbshit award of the century here. I was replacing my headlight stalk and at the same time checking the wire from the clockspring, and I swung my arm and accidentally hit the clockspring, and the wire BROKE. So now I have no horn/airbag until a new one comes in (which is $450 CAD). I am so pissed at myself you have no idea lol
Lesson: DO NOT HIT THE CLOCKSPRING OR THE WIRE WILL BREAK!! :(
enobmort42Denver, CO · Apr 22, 2009#134 Originally Posted by
devinlamothe ↑ OK so I get the dumbshit award of the century here. I was replacing my headlight stalk and at the same time checking the wire from the clockspring, and I swung my arm and accidentally hit the clockspring, and the wire BROKE. So now I have no horn/airbag until a new one comes in (which is $450 CAD). I am so pissed at myself you have no idea lol
Lesson: DO NOT HIT THE CLOCKSPRING OR THE WIRE WILL BREAK!! :(
ahhhh! oh no! 😲
devinlamotheSudbury, Canada · Apr 22, 2009#135 Originally Posted by PK198105 ↑
are you talking about the clockspring itself being broken or the connecting wires to the D3 connector?
The internal ribbon cable ripped out of the connection on the side ... I tried to see if it could be put back by taking the clockspring apart, but, stupid toyota glued the cable as well as had a clamp. If it was just clamped, it would have been fine.
The one good result, the turn signal is a lot quieter LOL
CTScottUSA, CT · Apr 22, 2009#136 Originally Posted by PK198105 ↑
I ran into those, but they are kind of large (~1" in diameter)
IllusionXBrossard, QC · Apr 22, 2009#137 Originally Posted by PK198105 ↑
ok so i checked the ECM in the engine bay and the 07 and therefore 08 seem to have the connection to A21 pin 40 (that is the ECM input pin 40) the wire is BLUE. Now this means that the junction box AD4 has this wire and it is accessed by pin 6 on the AD4 junction connector. Now im almost certain the only way to get to AD4 is to take off the top instrument panel.
I tried to find a suitable replacement for the AD4 but it seems this is the only way to get to the ECM pin 40 without having to go through the firewall. Now if someone knows of a fast and easy way of removing the top instrument panel please share your wisdom.
share the wisdom? pull the cluster cover, 2 bolts to remove the cluster and 2 cables to unplug.
pull the glove box, under there, there are 2 bolts that bolts down the air bag. unbolt and unplug the air bag (1 plug if i remember well, and no need to disconnect the battery) and then just pop the dash top cover, it comes right off, with the air bag.
I did it with the mechanics at Toyota. Took less than 5mins.
CTScottUSA, CT · Apr 23, 2009#138 Originally Posted by PK198105 ↑
We experimented with some of those for a work project. They are mighty cool, and about $60 each.
CTScottUSA, CT · Apr 23, 2009#139 Originally Posted by PK198105 ↑
do they come with embedded memory or you need to have a line in to display the images?
The ones that we were playing with had an embedded processor in them, so you could serially upload a .jpg converted to a .hex file.
AlexNet0Rockland, ME · Apr 24, 2009#140has anyone gotten it yet? how long do you think it should take?
CTScottUSA, CT · Apr 24, 2009#141 Originally Posted by
AlexNet0 ↑ has anyone gotten it yet? how long do you think it should take?
Gotten the Ebay stalks or gotten cruise working?
I've been cruising all week with my prototype setup. Today I ordered from Digikey a couple of different switch options since I can't decide which type I like best.
2006frontySan Bernardino · Apr 25, 2009#142mine was supposed to be delivered today but I wasn't home, I'm going to pick it up at the post office tomorrow.
IllusionXBrossard, QC · Apr 25, 2009#143 Originally Posted by PK198105 ↑
no stalk in the mail , but most likely ill be giving this one up for sale and going with the switches like CTScott, we just need to coordinate which switches we will use since i dont wanna copycat him
hey, i'm 1st on the list for your stalk.
Liu997Hicksville, LI · Apr 25, 2009#144Who wants to sell me their stalk, I'm second.
devinlamotheSudbury, Canada · Apr 27, 2009#145I'll probably be selling my stalk as well since I don't feel comfortable taking the dash apart to run the wires.
mrbondThread starterIllinois · Apr 27, 2009#146Well, I'm still waiting on my stalk, and I'm relatively comfortable taking apart the dash. I think, PK198105, that the wiring diagrams and such will need to be clarified...at least for my sake :P
mrbondThread starterIllinois · Apr 27, 2009#147^ lol whenever the damn stalk feels like arriving @_@
mikenacaratoBrentwood, TN · Apr 27, 2009#148ive got a friend at work who wants to do this pretty bad. what exactly would he have to do to run the oem switch. can someone type some quick step by step directions?
IllusionXBrossard, QC · Apr 28, 2009#149has the stalk arrived yet? PK ??
mikenacaratoBrentwood, TN · Apr 28, 2009#150ya if you could take some pics pk that would be marvelous :)