Yarisworld Archive

Cruise Control - Again!

48 posts · 62,055 views

CB900F2Original postToronto · Oct 25, 2008#1
I have a 08 CND Yaris Sedan with the convenience package, and I am wanting to install the Factory installed cruse control unit, but not wanting to Rostra version...

I have been doing a lot of research and found the following and I think the Yaris with the convenience package is all prewired for the Factory installed Cruse Control unit, and it is all but a matter of getting the control module and replacement rear cover for the steering wheel.

But there a few things to confirm:

Reference the online 2007 Yaris Factory Service Manual that is a sticky. And look at the CC section. I also reviewed the wiring diagram, and compared it to the car and it looks like all Cruse control wiring is in place, even the wiring going to the ECU, and the steering wheel connector is the 3 wire as required.

1/ The 2007 Factory Manual shows all that is needed is the Cruse Control for ATM…

2/ I reviewed Toyota EPC, again it is for the 2007 Yaris, and it shows for 2007 CND Sedan, there is a reference for the Cruse Control Module that is in the steering wheel. Anyone have access to the 2008 and 2009 EPC? As thecruse control parts on the 07 catalog, there is a reference link and it does not work..

http://www.toyodiy.com/parts/p_U_200...PRKK_4504.html


3/ Based on the 2007 EPC, it looks like the ECU is the same as long as it is the Yaris Sedan with the convenience package or higher.

4/ I went the dealer ship and saw the 2009 Yaris, and again, the Sedan with enhanced convenience and appearance package, it comes with the Factory Cruse control..


Anyone on our forum that works for a Toyota dealership and has access to 2008/2009 Toyota EPC and hopfully has Canadian Spec Yaris also to confirm part#s and ECU??

What do you guys think?.. Am I chasing a ghost?

Replies 47

CTScottUSA, CT · Oct 25, 2008#2
Originally Posted by CB900F2 ↑
I have a 08 CND Yaris Sedan with the convenience package, and I am wanting to install the Factory installed cruse control unit, but not wanting to Rostra version...

I have been doing a lot of research and found the following and I think the Yaris with the convenience package is all prewired for the Factory installed Cruse Control unit, and it is all but a matter of getting the control module and replacement rear cover for the steering wheel.

But there a few things to confirm:

Reference the online 2007 Yaris Factory Service Manual that is a sticky. And look at the CC section. I also reviewed the wiring diagram, and compared it to the car and it looks like all Cruse control wiring is in place, even the wiring going to the ECU, and the steering wheel connector is the 3 wire as required.

1/ The 2007 Factory Manual shows all that is needed is the Cruse Control for ATM…

2/ I reviewed Toyota EPC, again it is for the 2007 Yaris, and it shows for 2007 CND Sedan, there is a reference for the Cruse Control Module that is in the steering wheel. Anyone have access to the 2008 and 2009 EPC? As thecruse control parts on the 07 catalog, there is a reference link and it does not work..

http://www.toyodiy.com/parts/p_U_200...PRKK_4504.html


3/ Based on the 2007 EPC, it looks like the ECU is the same as long as it is the Yaris Sedan with the convenience package or higher.

4/ I went the dealer ship and saw the 2009 Yaris, and again, the Sedan with enhanced convenience and appearance package, it comes with the Factory Cruse control..


Anyone on our forum that works for a Toyota dealership and has access to 2008/2009 Toyota EPC and hopfully has Canadian Spec Yaris also to confirm part#s and ECU??

What do you guys think?.. Am I chasing a ghost?

I don't have access to the EPC, but attached are the EWD's for factory cruise for 08 and 09. The pinouts associated with cruise are identical for both. (Save them locally to view, as they are huge images to be readable)



CB900F2Thread starterToronto · Oct 25, 2008#3
Scott..

Thanks for the two EWD, but the files are very hard to read if I zoom into them..

Where can I get a copy that is easier to read?

thanks Scott..
CTScottUSA, CT · Oct 25, 2008#4
Originally Posted by CB900F2 ↑
Scott..

Thanks for the two EWD, but the files are very hard to read if I zoom into them..

Where can I get a copy that is easier to read?

thanks Scott..
Refresh the thread - I didn't realize that image bucket defaults to resizing to 1024x768. I re-uploaded them at full res, which updates them in the thread as well...
CB900F2Thread starterToronto · Oct 25, 2008#5
Thanks Scott.. Do you mind me asking where you where able to find them?

thanks again!


Originally Posted by CTScott ↑
Refresh the thread - I didn't realize that image bucket defaults to resizing to 1024x768. I re-uploaded them at full res, which updates them in the thread as well...
CTScottUSA, CT · Oct 25, 2008#6
Originally Posted by CB900F2 ↑
Thanks Scott.. Do you mind me asking where you where able to find them?

thanks again!
I purchased the EWD's for 08 and 09 from Toyota TechInfo.
firemachine69Sudbury, On · Oct 25, 2008#7
No such thing as a factory cruise. Dealer-installed. This has been covered numerous times.
CB900F2Thread starterToronto · Oct 25, 2008#8
Take a look at your local Toyota and see if they have 2009 models in stock, and find a S/D with the enhanced convenience and appearance package, and you will find the factory installed CC.... Hope this helps...


Originally Posted by firemachine69 ↑
No such thing as a factory cruise. Dealer-installed. This has been covered numerous times.
firemachine69Sudbury, On · Oct 25, 2008#9
Not in Canada. Although that may have changed for '09. (I believe my salesman was pitching that to me, although I can't recall for certainty).
CB900F2Thread starterToronto · Oct 28, 2008#10
For this project, I am wanting to find out based on now that the 09 CND version does have CC as a factory install, the part# for the steering wheel control unit.

Also, if there is anyone who works for a Toyota dealership and has access to ECP, and not sure if their ECP will include CND spec cars, and from the link I have above of the steering wheel, what does the link to referenced PNC 84632 tell us?...

Also, for the years of 07, 08..The steering wheel CC switch assembly, is it the same one use in Corolla, Camery???

But now, the best thing for us is to find out the parts listing for 09 and cofirm the part# for the CC control unit..

thanks



Originally Posted by firemachine69 ↑
Not in Canada. Although that may have changed for '09. (I believe my salesman was pitching that to me, although I can't recall for certainty).
b_hickman11Tyler, TX · Oct 28, 2008#11
Originally Posted by firemachine69 ↑
No such thing as a factory cruise. Dealer-installed. This has been covered numerous times.
Yes there is.....
b_hickman11Tyler, TX · Oct 28, 2008#12
Originally Posted by CB900F2 ↑

Also, for the years of 07, 08..The steering wheel CC switch assembly, is it the same one use in Corolla, Camery???
My 2005 Tacoma had the same CC assembly as my 2008 Yaris(with power package). My parents 2001 Tacoma has the same CC assembly as my 2007 Yaris(without power package). Therefore I believe that all Toyota's, to at least 2001, have the same CC assembly.
CTScottUSA, CT · Oct 28, 2008#13
Originally Posted by CB900F2 ↑
I have a 08 CND Yaris Sedan with the convenience package, and I am wanting to install the Factory installed cruse control unit, but not wanting to Rostra version...

I have been doing a lot of research and found the following and I think the Yaris with the convenience package is all prewired for the Factory installed Cruse Control unit, and it is all but a matter of getting the control module and replacement rear cover for the steering wheel.

But there a few things to confirm:

Reference the online 2007 Yaris Factory Service Manual that is a sticky. And look at the CC section. I also reviewed the wiring diagram, and compared it to the car and it looks like all Cruse control wiring is in place, even the wiring going to the ECU, and the steering wheel connector is the 3 wire as required.

1/ The 2007 Factory Manual shows all that is needed is the Cruse Control for ATM…

2/ I reviewed Toyota EPC, again it is for the 2007 Yaris, and it shows for 2007 CND Sedan, there is a reference for the Cruse Control Module that is in the steering wheel. Anyone have access to the 2008 and 2009 EPC? As thecruse control parts on the 07 catalog, there is a reference link and it does not work..

http://www.toyodiy.com/parts/p_U_200...PRKK_4504.html


3/ Based on the 2007 EPC, it looks like the ECU is the same as long as it is the Yaris Sedan with the convenience package or higher.

4/ I went the dealer ship and saw the 2009 Yaris, and again, the Sedan with enhanced convenience and appearance package, it comes with the Factory Cruse control..


Anyone on our forum that works for a Toyota dealership and has access to 2008/2009 Toyota EPC and hopfully has Canadian Spec Yaris also to confirm part#s and ECU??

What do you guys think?.. Am I chasing a ghost?


Here are the parts shown in the EPC for 2009:

84632-34011 - Switch, Cruise Control Main
84633-42030 - Wire, Cruise Control
88280-14030 - Switch Assy, Clutch (M/T only)
90159-51099 - Screw, W/Washer - quantity 2
45184-52130-B0 - Cover, Steering Wheel Boss, Lower (Cruise Control-With)

(The big question is if this is truly all that is required. If you look at the EWD, it really looks like everything is built in except the column switch and the clutch switch).

CB900F2Thread starterToronto · Oct 28, 2008#14
Scott..

YOU DA MAN!.....

Would it be possible if you can look through the EPC for the US ver 08 Sedan with the power package as b hickman11 stated this version of the 08 Sedan came with the factory CC and confirm the the 08 model uses the same part#s

Also.. Does anyone know if the one was to order from the dealer an ECU if it requires to be flashed, or do they come preflashed (Program).. Rockland should be able to help us on this...
CTScottUSA, CT · Oct 28, 2008#15
Originally Posted by CB900F2 ↑
Scott..

YOU DA MAN!.....

Would it be possible if you can look through the EPC for the US ver 08 Sedan with the power package as b hickman11 stated this version of the 08 Sedan came with the factory CC and confirm the the 08 model uses the same part#s

Also.. Does anyone know if the one was to order from the dealer an ECU if it requires to be flashed, or do they come preflashed (Program).. Rockland should be able to help us on this...
It is a bit difficult to verify without a VIN number with the specific config, but it looks like:

2009 ECU USA SED&LB Auto - 89661-52J50
2008 ECU USA SED Auto - 89661-52G41 (11/07 - 08/08)
89661-52G51 (11/07 - 08/08)
89661-52J40 (08/08+)
89661-52J50 (08/08+)

There is no indication of cruise in relation to ECU part #.
CB900F2Thread starterToronto · Oct 29, 2008#16
Thanks Scott..

Guys. Take a read on the same upgrde on a 09 Corolla...

http://www.toyotanation.com/forum/sh...ht=84632-34011

Also.. take a read on the installation guide, and the tool that they use to cut open the back steering wheel cover to allow the cc control to pass through.. Anyone seen this, or knows of the manufacture,part# etc... I would like to find out more details on it..

http://www.trdsparks.com/install/00016-01208inst.pdf


P.S... Looks like we can order this kit as it is the same CC unit and wire set used in the Corolla 09 and the Yaris...
CTScottUSA, CT · Oct 29, 2008#17
Originally Posted by CB900F2 ↑
Thanks Scott..

Guys. Take a read on the same upgrde on a 09 Corolla...

http://www.toyotanation.com/forum/sh...ht=84632-34011

Also.. take a read on the installation guide, and the tool that they use to cut open the back steering wheel cover to allow the cc control to pass through.. Anyone seen this, or knows of the manufacture,part# etc... I would like to find out more details on it..

http://www.trdsparks.com/install/00016-01208inst.pdf


P.S... Looks like we can order this kit as it is the same CC unit and wire set used in the Corolla 09 and the Yaris...

I just looked up the 09 Corolla and it has a different part number for the switch and the wire for NAP, but same parts as Yaris for JPP:

For NAP Corollas:
Switch, Cruise Control Main: Corolla 84632-08021 vs Yaris 84632-34011
Wire, Cruise Control: Corolla 84633-0E020 vs Yaris 84633-42030


As for the tool, it is just a die punch - Two drill bits would accomplish the same task.
CB900F2Thread starterToronto · Oct 29, 2008#18
Alright guys, whos in!...

Any 07,08 willing to take the plunge??
CB900F2Thread starterToronto · Oct 30, 2008#19
Anyone, Anyone, Anyone???......

Hmmm... What would be holding some of you CC wanters back??
b_hickman11Tyler, TX · Oct 30, 2008#20
Originally Posted by CB900F2 ↑
Anyone, Anyone, Anyone???......

Hmmm... What would be holding some of you CC wanters back??
This has already been done. There were many threads about this topic pre-hack.
CB900F2Thread starterToronto · Oct 30, 2008#21
B... I dont recall any of the threads mentioning any of our members trying to connect the OEM CC switch assemble with the required wiring harness to the steering wheel connector to test it… Unless I over look it…

Can you elaborate on the issue that was found back then?..

- Was it a wiring issue?
- ECU Issues?

Thanks…



QUOTE=b_hickman11;160196]This has already been done. There were many threads about this topic pre-hack.[/QUOTE]
b_hickman11Tyler, TX · Oct 30, 2008#22
are you wanting the CC that comes with the power package or the one that comes without the power package?
CB900F2Thread starterToronto · Nov 1, 2008#23
I assume in the US, the PowerPackage is the package that came with the factory OEM CC switch that is built into the steering wheel as noted by Scotts parts diagram.. If so, yes...

b, you noted that you have a sedan with the power package and cc, do you mind checking your ECU part number?, it will be noted on the front of the ECU on a sticker..

thanks


Originally Posted by b_hickman11 ↑
are you wanting the CC that comes with the power package or the one that comes without the power package?
MidonGainesville, TX · Nov 1, 2008#24
Originally Posted by CB900F2 ↑
Anyone, Anyone, Anyone???......

Hmmm... What would be holding some of you CC wanters back??
I want to do this, but what parts would I need 08 LB MT and all I got was a premium audio system, so I don't know which ones I need.
CB900F2Thread starterToronto · Nov 1, 2008#25
All of the items below...

84632-34011 - Switch, Cruise Control Main
84633-42030 - Wire, Cruise Control
88280-14030 - Switch Assy, Clutch (M/T only)
90159-51099 - Screw, W/Washer - quantity 2
45184-52130-B0 - Cover, Steering Wheel Boss, Lower (Cruise Control-With)


Originally Posted by Midon ↑
I want to do this, but what parts would I need 08 LB MT and all I got was a premium audio system, so I don't know which ones I need.
MidonGainesville, TX · Nov 1, 2008#26
Originally Posted by CB900F2 ↑
All of the items below...

84632-34011 - Switch, Cruise Control Main
84633-42030 - Wire, Cruise Control
88280-14030 - Switch Assy, Clutch (M/T only)
90159-51099 - Screw, W/Washer - quantity 2
45184-52130-B0 - Cover, Steering Wheel Boss, Lower (Cruise Control-With)
Got it I will have to get this done after my current MOD. Printing the list right now.
🙇🙇🙇🙇🙇🙇
b_hickman11Tyler, TX · Nov 1, 2008#27
Originally Posted by CB900F2 ↑
I assume in the US, the PowerPackage is the package that came with the factory OEM CC switch that is built into the steering wheel as noted by Scotts parts diagram.. If so, yes...

b, you noted that you have a sedan with the power package and cc, do you mind checking your ECU part number?, it will be noted on the front of the ECU on a sticker..

thanks
Yes I have an 08 with the power package that has CC and an 07 without power package that has CC. The power package CC is always mounted on the right side of the steering column while the non-power package CC is mounted on the left side of the steering column.

I will check my ECU part number....One questions though, where is the ECU? I know Im a noob....
CB900F2Thread starterToronto · Nov 1, 2008#28
In the engine bay on the left handside on the back wall.. You will see two large connector on the top of it.. the label is in the middle of the ECU on the face..

If you can, can you check your 07 and 08?

thanks


Originally Posted by b_hickman11 ↑
Yes I have an 08 with the power package that has CC and an 07 without power package that has CC. The power package CC is always mounted on the right side of the steering column while the non-power package CC is mounted on the left side of the steering column.

I will check my ECU part number....One questions though, where is the ECU? I know Im a noob....
StolnWinnipeg, Canada · Nov 1, 2008#29
does the 07 yaris rs have a light on the dash for the cruise? I have the aftermarket dealer installed cruise on the left hand side with a green light on the stick. If I can change to the better looking one I will as I would assume all the parts are there, so a stick change should work. Shed some light into this issue, will it work?
CTScottUSA, CT · Nov 1, 2008#30
Originally Posted by Stoln ↑
does the 07 yaris rs have a light on the dash for the cruise? I have the aftermarket dealer installed cruise on the left hand side with a green light on the stick. If I can change to the better looking one I will as I would assume all the parts are there, so a stick change should work. Shed some light into this issue, will it work?
Yes, the crusie light is built into the combination meter. I really don't understand why the dealer installed ones are aftermarket ones. It kind of makes me think that there is something more to this than we think...
CB900F2Thread starterToronto · Nov 1, 2008#31
It does seem that way, but for all of the info on the OEM CC unit and the info all being OEM like the Service Manual, EPC, and confirmed wiring is there... and the confirmed 08 model with the enhanced power package comes with the OEM CC, it makes no sense to why the aftermarket unit was pushed as the dealer install option..

I have been searching the local wreckers to find a compatible CC switch which from all of the online Toyota OEM parts suppliers claims that 07+ Camry and many other models of cars use the same CC switch unit...

I will then purchase the wire harness once I have the switch and give it a shot (cross my fingers!).. Unless someone can beat me too it!

Originally Posted by CTScott ↑
Yes, the crusie light is built into the combination meter. I really don't understand why the dealer installed ones are aftermarket ones. It kind of makes me think that there is something more to this than we think...
b_hickman11Tyler, TX · Nov 1, 2008#32
Originally Posted by CB900F2 ↑
It does seem that way, but for all of the info on the OEM CC unit and the info all being OEM like the Service Manual, EPC, and confirmed wiring is there... and the confirmed 08 model with the enhanced power package comes with the OEM CC, it makes no sense to why the aftermarket unit was pushed as the dealer install option..

I have been searching the local wreckers to find a compatible CC switch which from all of the online Toyota OEM parts suppliers claims that 07+ Camry and many other models of cars use the same CC switch unit...

I will then purchase the wire harness once I have the switch and give it a shot (cross my fingers!).. Unless someone can beat me too it!

As I posted before, my 08 with power package has the same CC that was in my 05 Tacoma so more than likely all Toyota's CC for vehicles with the power package is the same(at least going back to 2005). My 07 does not have the power package but has the Rostra CC. This CC was not installed by the dealer. It was either installed by the distributor(the port) or was installed in Japan. The same exact Rostra CC that is on my 07 Yaris is the same one that is on my parents 2001 Tacoma. So Toyota has been using the same setup for at least 7 years.

I will take a look at my ECU number tomorrow and post them on here.
b_hickman11Tyler, TX · Nov 2, 2008#33
Originally Posted by CB900F2 ↑
I assume in the US, the PowerPackage is the package that came with the factory OEM CC switch that is built into the steering wheel as noted by Scotts parts diagram.. If so, yes...

b, you noted that you have a sedan with the power package and cc, do you mind checking your ECU part number?, it will be noted on the front of the ECU on a sticker..

thanks

89661-52G51 Power Package
89661-52F11 Non Power Package
CB900F2Thread starterToronto · Nov 3, 2008#34
Thanks for the feedback...

My 08 Sedan has the same ECU as your 08 with the PP and OEM CC..

So, it looks like all of the planets are pretty much all lined up…

Confirmed ECU, Wiring is in place, Confirmed part#s…. Just need to try it now..


Originally Posted by b_hickman11 ↑
89661-52G51 Power Package
89661-52F11 Non Power Package
JnCCharlotte, NC · Nov 9, 2008#35
Can this be retrofitted to a US 07+ Liftback?
b_hickman11Tyler, TX · Nov 9, 2008#36
Originally Posted by JnC ↑
Can this be retrofitted to a US 07+ Liftback?
It's the same CC as an 05 Tacoma so yes, it will fit an 07.
CB900F2Thread starterToronto · Nov 29, 2008#37
b_hickman11 or anyone else with OEM CC, when you turn your ignition key to the point just before engaging the starter and the dash symbols light up, does your “Cruse” indicator also light up as part of the dash display test?

Thanks guys.
CB900F2Thread starterToronto · Nov 29, 2008#38
Hey guys... My dream of installing OEM CC on my 08 CND Sedan Yaris might have come to an end... 😠 😢

I used my camera with the flash too see if I can see the dash "CRUISE" indicator that should be near the right turn signal, and I can not see the outline of the "CRUISE" indicator...

For you 08 Sedan PowerPackage owners, when you turn on your CC, is the dash indicator close to the right hand turn signal?
3068295821_875e0187f7.jpg
b_hickman11Tyler, TX · Nov 29, 2008#39
You are only going to find the "cruise" symbol on the Yaris's with the power package. On the non-power packagae Yaris, the cruise indicator is on the steering wheel control.

If you are wanting to get the OEM cruise from the power package added you are also going to have to buy a new gauge cluster that has the tach on it.
RevssonSoutheast Wisconsin · Nov 29, 2008#40
Originally Posted by CB900F2 ↑
Hey guys... My dream of installing OEM CC on my 08 CND Sedan Yaris might have come to an end... 😠 😢

I used my camera with the flash too see if I can see the dash "CRUISE" indicator that should be near the right turn signal, and I can not see the outline of the "CRUISE" indicator...

For you 08 Sedan PowerPackage owners, when you turn on your CC, is the dash indicator close to the right hand turn signal?
Does your Canadian Yaris come with a tachometer?
Looking at the 2007 Factory Service Manual, it shows the cruise light
in a different spot on the I/P if you don't have the tachometer.
Take a look at page 15 of the Cruise Control pdf:

http://www.etimago.com/yaris/repairm...%20Control.pdf

That being said, I have a 2009 LB with Power Pkg and CC, but no tach.
My indicator is in the upper right, like the pdf shows for the tach model. 🤷
Maybe the 2009 service manual would show something different.
CTScottUSA, CT · Nov 29, 2008#41
Originally Posted by Revsson ↑
Does your Canadian Yaris come with a tachometer?
Looking at the 2007 Factory Service Manual, it shows the cruise light
in a different spot on the I/P if you don't have the tachometer.
Take a look at page 15 of the Cruise Control pdf:

http://www.etimago.com/yaris/repairm...%20Control.pdf

That being said, I have a 2009 LB with Power Pkg and CC, but no tach.
My indicator is in the upper right, like the pdf shows for the tach model. 🤷
Maybe the 2009 service manual would show something different.
My 09 LB has power, no CC, no Tach. With the camera method, I see two CC lights - SET, and one that looks like a speedometer.
CB900F2Thread starterToronto · Nov 30, 2008#42
Yes..
My 08 Sedan with the power package has the tach in the dash..

DAM!... I thought I had all the planets aligned up!... (Wiring, ECU, Part#s for the OEM CC parts)..... I would have thought (assumed!), that Toyota would have used the same dash for both cars that have the OEM CC installed or not (with the tach of course)… DAM!...

Anyone outside of N.A that has a 08 Sedan with the tach, but no OEM CC installed, can you take a picture of your dash too see if you have the CC indicator in your dash?... It is preferred if you have a metric dash (KM)

DAM, DOUBLE DAM!!!

P.S.. Can someone with a 08 US Sedan (w/tach) take the same picture… I would like to see how well does the CC indicator shows up.

Originally Posted by Revsson ↑
Does your Canadian Yaris come with a tachometer?
Looking at the 2007 Factory Service Manual, it shows the cruise light
in a different spot on the I/P if you don't have the tachometer.
Take a look at page 15 of the Cruise Control pdf:

http://www.etimago.com/yaris/repairm...%20Control.pdf

That being said, I have a 2009 LB with Power Pkg and CC, but no tach.
My indicator is in the upper right, like the pdf shows for the tach model. 🤷
Maybe the 2009 service manual would show something different.
CTScottUSA, CT · Nov 30, 2008#43
Originally Posted by CB900F2 ↑
Yes..
My 08 Sedan with the power package has the tach in the dash..

DAM!... I thought I had all the planets aligned up!... (Wiring, ECU, Part#s for the OEM CC parts)..... I would have thought (assumed!), that Toyota would have used the same dash for both cars that have the OEM CC installed or not (with the tach of course)… DAM!...

Anyone outside of N.A that has a 08 Sedan with the tach, but no OEM CC installed, can you take a picture of your dash too see if you have the CC indicator in your dash?... It is preferred if you have a metric dash (KM)

DAM, DOUBLE DAM!!!

P.S.. Can someone with a 08 US Sedan (w/tach) take the same picture… I would like to see how well does the CC indicator shows up.

Wow, looking at the EPC, there are quite a few iterations (12+) of the 08 sedan combo meter:

None mention cruise, but the following have tach:
83800-52W10
83800-52F21
83800-52S60
83800-52S70
83800-52S40
83800-52S50
83800-52E81
RevssonSoutheast Wisconsin · Dec 6, 2008#44
I should try and take some pics, but my 2009 Cruise light and Set light are above the
fuel indicator not near the turn signal. This is different that where it is shown on the
EWD for the 2007.
CB900F2Thread starterToronto · Dec 6, 2008#45
If you can take the photos that would be great...

Scott did post a 2009 EWD, and it does have a slightly different setup for the CC, it is the active light "Cruise" and the "SET" light when it being used

P.S.. Anyone with a 08 that has the OEM CC, can you post a photo of your dash also?

thanks guys..


Originally Posted by Revsson ↑
I should try and take some pics, but my 2009 Cruise light and Set light are above the
fuel indicator not near the turn signal. This is different that where it is shown on the
EWD for the 2007.
dono187Des Moines Iowa · Nov 14, 2009#46
😕 For reference, I am definitely a noob, and have browsed through some of these threads.
Anyways... That all being said, I have an 08 Yaris, without any options except automatic tranny. Just tried installing the OEM cc on the wheel. The install worked great, and was actually quite easy, except that: the Cruise don't work. All I did was pop out the airbag, pop a hole in the plastic behind the steering wheel, stick in the OEM Toyota CC, and put it all back together. That all worked well, but the cruise doesn't kick in. Am wondering if there's something in the ECU I have to do to make it recognize the cc? I did check, and I do not have the cruise light on the dash, because as I mentioned, mine is the very bare bines one.

Thoughts?

FYI, I paid $110, for the OEM toyota cruise stalk and the wirnign harness from Metro Toyota ( cleveland, I think) If anyone is looking for the same, would be happy to post the link to their site. They were very good, and helped me out with the couple questions I had.

Anyways, any advice anyone can spot would be appreciated. Thanks.

D
CTScottUSA, CT · Nov 14, 2009#47
Originally Posted by dono187 ↑
😕 For reference, I am definitely a noob, and have browsed through some of these threads.
Anyways... That all being said, I have an 08 Yaris, without any options except automatic tranny. Just tried installing the OEM cc on the wheel. The install worked great, and was actually quite easy, except that: the Cruise don't work. All I did was pop out the airbag, pop a hole in the plastic behind the steering wheel, stick in the OEM Toyota CC, and put it all back together. That all worked well, but the cruise doesn't kick in. Am wondering if there's something in the ECU I have to do to make it recognize the cc? I did check, and I do not have the cruise light on the dash, because as I mentioned, mine is the very bare bines one.

Thoughts?

FYI, I paid $110, for the OEM toyota cruise stalk and the wirnign harness from Metro Toyota ( cleveland, I think) If anyone is looking for the same, would be happy to post the link to their site. They were very good, and helped me out with the couple questions I had.

Anyways, any advice anyone can spot would be appreciated. Thanks.

D
2008 Yaris don't have the wiring from the ECM to the steering wheel, so you have to run a wire from pin 40 of the ECM connector A21 to the connector on the steering column where the spiral cable comes out. Take a look at the following post. Since you bought an OEM stalk, you can ignore the part about the switches are resistors.


DIY Cruise Control on 07-08 Yaris (step by step)
YsfaelTexas · Jun 17, 2010#48
2010 Yaris, Manual Trans base model. I was able to retrofit an OEM cruise. Took about an hour, but I do this for a living. Thought someone here might want to know.

BTW, pin 40 on th ECU had a connector in it even though the steering wheel connector didn't. Went ahead and hard wired like I would have otherwise.

Respect,
Ysfael