Yarisworld Archive

T Montague's 2zr swap - '08 m/t sedan some extra info

283 posts · 200,320 views · page 5 of 6

Replies continued

CrankyOldManWest Michigan · Jun 7, 2019#201
Sweet! I've seen the same fender trick done on an SW11 MR2.
tmontagueThread starterCaledonia Ont. · Jun 9, 2019#202
Well, the first track day of the year went off very well on Friday night. Met up with Ron and a couple other guys/gals from the WannaBspecs and we all had fun times lapping and chatting. It's always a fun time when you can meet up with friends vs flying solo.

I learned a ton of info on how successful my winter modifications were and how important confidence inspiring tires are. Long story short, I beat my fastest lap time from last year by over 3.5 seconds...and there is at least a second more to be had just in braking zones. My current fastest lap is a 1:26:48 and I was consistently turning out laps of 1:27. This makes driving on the track much more enjoyable as I am now the one putting pressure on other fast cars and getting the point by, vs having to always point others by.

The Nankang AR1's are very good tires. They give an audible feedback when pushed to the limit and they breakaway in a very controllable manner. This encourages you to drive past the tires limit and use driver skill to control the slide. This is much faster and allows you to learn how to drive with some slip angle. My confidence has gone up tremendously with these tires over the corded BFG R1's as I now can drive 10/10ths and push past the limit of the tires and not deal with snap oversteer.

I also noticed that the AR1's really shine in braking zones. I find myself realising that I have braked and scrubbed off too much speed before some corners. If you do go into a corner with too much speed these tires are still controllable in a well balanced car. My car now had a tendency to understeer and I'll have to play around with a higher dampening in the rear than what I ran with the R1's. I didn't adjust dampening this track day as it was only the first outing, but once it is adjusted to increase oversteer, my lap times should greatly improve. I prefer a slight tail happy car, and although it isn't plowing right now, it isn't as tail happy as I would like. I find it difficult in the twistys to get the rear end to kick out with lifting off the throttle so I don't have to steer to get me pointed to where I want.

Pic of the brand new tires after 133km of hard flogging of the car - it took it like a champ
The most worn tire (front left - TMP is notoriously hard on FL tires)
Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

I think I have hit the limit of the Carbotech XP10's. They have only about 20% left in them and 3 of the 4 pads are past the rivets (this is fine as the rivets are made with a soft metal so they don't eat away at the rotor for this reason) I never experienced brake fade at all but they xp10's seemed to have lost their hard initial bite that I'm accustomed to. Also there very fast wear rate would explain this as well.

I have contacted a company called G-loc brakes which is a spin off of Carbotech and they have similar compound formulation as Carbotech with a slightly cheaper price and some good reviews on longevity with some Unlimited Time Attack FWD guys. I'm waiting for their recommendation on pad compound and then I'll pull the trigger. I don't think my pads will last another full track day so I'll probably have to keep them as emergency back ups.

most worn pad
Picture not included in this copy

Picture not included in this copy

I have found that both front calipers have multiple tears in the rubber dust boot which looks to be caused from the heat or just the fact that they are over 10 years old. I'll use them for the rest of the season but plan to rebuild them this year with a rebuild kit off of RockAuto. They are not leaking at all, just the dust boot is torn.

Here is some really valuable info that I have been excited to find out - Oil and coolant temp/pressure info. So, recall that last year with ~ 25-28C ambient temps my coolant would peak at 238F and typically would sit at 228-235F about 8 mins into a session.

Oil temps would start to follow and would peak at 290F and typically sit around 285F as long as I was redlining the engine and going WOT (so for most of the session). This was on 5w30 Pennzoil UP oil.

On Friday the ambient temps were 24C (slightly lower than last summer) and I am now running Quaker State UD 0w20 and I now have a larger frontal area and dual core radiator, no a/c condenser in front of the rad and radiator ducting from the whole lower grill mouth. Here is my peak and average temps and pressure readings from the full Friday session:

Oil temp Peak: 252F AVG: 242F
Oil Pressure at idle right when I pulled in the paddock: 8-9 psi
Coolant temp peak: 191F AVG 188F

It is logical that oil and coolant temp influence each other and that lowering coolant will bring oil temps down to a certain degree. Also 0w20 oil will run cooler than a 5w30 as tests have shown in the gt-86 community. But damn am I ever impressed with my driveway fabricated/hacked radiator install and ducting. I now have lower on track coolant temps with my current set up than I ever did in bumper to bumper traffic with the OE radiator! I also found out my Mishimoto fan works excellently and fairly quietly as it kicked on when coolant peaked at 204F only in the paddock once my car was sitting. It would run for 30 seconds to a minute and then kick off.

The coolest part of the evening was having boosted >$100 grand BMW's from the wealthy foreign students flying off the track in clouds of dust trying to stick on my tail through the higher speed turns (money doesn't buy driver skill). I also had a few go off in front of me as they refused to give me a point by so I rode their ass throughout the twisty part of the track and they would over drive and go off in turns. They later that night a handful of them coming up to my car asking what crazy set up I had under the hood. To their dismay it is a stock Corolla engine with stock tune with approx 132whp...

I had another group comment on how cool it was that a Yaris was so fast and how it sounded like there was an insane engine under the hood (currently running 1 cat and resonator only). These same people were mentioning how their STI and Cobalt SS could only do 3 laps and then their (boosted) engines would heat soak and pull timing and their brakes would fade. Not the Yaris, lap after lap it just kept getting faster and faster, no timing pulled, no heat soak, no engine issues or temp problems, just absolutely perfect. One of the many reasons all engine builds are ideal for the track.

The only odd thing I noticed was that during high rpm, WOT if I looked at the oil temp, it would fluctuate between the highest temp (244F) and down as low as 186F quickly. Almost as if the oil was being pumped so fast it was either missing oil and reading air, or the oil was actually cooler in certain parts it was picking up due to very high oil flow...I'm stumped on this one. As soon as the rpm dropped the temp read consistent around 244F.

My front left tire which is the most stressed lost a huge amount of air on one session. It seemed like it wasn't leaking but may have burped some on turn 1. I refilled it a bit higher and after a couple more sessions, it did lose a bit more but never that large amount. I checked it when I got home and using the soapy water test, it came up negative for leaks. I'll check it over the next few days and see how it hold air. I may just have to run that tire at a much higher psi so the sidewall is stiffer.

All in all a great session and it really highlighted the potential this car has. I am very impressed with how well my cooling mods did and how effective they were. It was also nice to see science and empirical data win out in the real world over age old tradition in regards to oil viscocities. After the temps and pressures seen this session, I'm doubtful I will ever have a situation where 5w30 is needed.
heeroyuy01195Florida · Jun 10, 2019#203
Sounds like you had a blast, lots of good info here!

That does wound a bit odd with the oil temps. Not sure if this applies to the 2zr but I know with the 4ages we have oil starvation problems when it's being pushed hard and/or during repeated hard cornering. We combat this with running a baffle in the oil pan or if you're truly dedicated, going with a dry sump setup. It's been a little while since I've worked on my MR2 or done much reading on the 4age so take that with a grain of salt. Anywho, perhaps it's similar with the 2zr?
tmontagueThread starterCaledonia Ont. · Jun 10, 2019#204
Originally Posted by heeroyuy01195 ↑
Sounds like you had a blast, lots of good info here!

That does wound a bit odd with the oil temps. Not sure if this applies to the 2zr but I know with the 4ages we have oil starvation problems when it's being pushed hard and/or during repeated hard cornering. We combat this with running a baffle in the oil pan or if you're truly dedicated, going with a dry sump setup. It's been a little while since I've worked on my MR2 or done much reading on the 4age so take that with a grain of salt. Anywho, perhaps it's similar with the 2zr?
This is what I originally thought, dreaded oil starvation. However, this was only noticed on the front straightaway (mind you I wasn't able to monitor my gauges in the corners). At this same time my oil pressure was always consistent and fine, something I would have expected to drop if it was oil starvation.

At this point I don't know what it is from, I'm thinking something to do with the oil pressure bypass as it dumps excess oil back into the pan? My engine has no new noises or weird hiccups so I can't imagine oil starvation has been a problem for me yet.

As a side note - I looked back into my thread and realized that the xp10's only lasted me 3 track day or ~350-370km's. Of which the first track day was my first time on a track pad so I wasn't pushing them nearly as hard as I did this last session. Definitely going with G-Loc pads next and a much stronger compound, hopefully they will last longer
ern-dizCA all day · Jun 10, 2019#205
Originally Posted by heeroyuy01195 ↑
...lots of good info here!
+1
tmontagueThread starterCaledonia Ont. · Jun 11, 2019#206
After reviewing the track day in my head I have come to some conclusions on what I can improve on. First and foremost, I need a higher heat track pad - so far it seems I will be going with G-Loc's R16 compounds which can take up to 2000F and has a slightly higher coefficient of friction than my xp10's from Carbotech.

I have no doubt that I can get well into the 1:25's with a little bit or time on my current set up. Things that I noticed at the last track day:

1. I was braking too early for my new tires and brake set up. I found myself going into the corners hard, but I was throttling through the corner almost right after entering it. This means I could have braked later and carried more speed into the corner.

2. I wasn't able to adequately trail brake to swing my rear end around and I was more or less controlling the under steer throughout the corners. This is partly due to issue #1. I braked too early which scrubbed off too much speed so I didn't have enough momentum going into the corner to scrub off with trail braking.

3. There are a few faster paced dogleg corners that I know the car is capable of going through while staying on full throttle. As of now I am backing off and only giving part throttle. This is causing me to not have enough momentum to trail brake into turn 11 (the last turn before the final straight away)

With my old tire set up the snap over steer was so quick and without warning that I would have to be cautious of it and back on going late into corners. With my set up this year, I can brake late into corners with some solid trail braking as my oversteer is much more controlled. My front tires (especially the FL) were worn down quite a bit and took a beating. They took it like a champ but compared to the rear they work over time. This is partly due to my car being FWD, the track and me not trail braking enough. With my more or less controlling under steer most laps instead of over steer, the front tires got more cooked.

I also had some constant air loss in my FL tire but yet I have no air leaks. It was due to the tire burping air during hard cornering. I will have to air it up a bit more next time out but I also need to work the rear tires more so the front are worked less - oversteer will achieve this.

Next session out will be focusing on braking later and trail braking to see how late I can go and how well the rear end kicks out. I've contemplated doing some driver education classes at the track as they would really help a more experienced driver pin point what I can do in the car to make my times faster. The thing is that they cost around $400-$500 for the day which at this point in time is money I don't have if I want to be able to afford wear items and keep my car track ready. I do think the HPDE events are a great idea but I am still getting faster and faster every time out at the track and I am always reading as much as I can and talking to more experienced drivers. So for now I'll have to forgo the HPDE courses until I start to plateau or have some more cash.
06YarisRSFredericton, New Brunswick, Canada · Jun 12, 2019#207
Sounds like you are figuring out how to squeeze every ounce of performance out of the Yaris sedan. It's really great to hear how capable our little bugs are, especially when compared to more expensive sport-type cars. Great wotk there Mr. Montague. 👍 Excellent research put into practice. Kudos!
tmontagueThread starterCaledonia Ont. · Jun 13, 2019#208
Originally Posted by 06YarisRS ↑
Sounds like you are figuring out how to squeeze every ounce of performance out of the Yaris sedan. It's really great to hear how capable our little bugs are, especially when compared to more expensive sport-type cars. Great wotk there Mr. Montague. 👍 Excellent research put into practice. Kudos!
thank you. Unfortunately I will have to sit out the rest of June in terms of going to the track. I'm off work studying for the last of my board exams and we are planning to sell our house in September so money isn't free flowing right now. I also have burned through almost all of the pad life on my xp10's and track pads are not cheap at over $300 for the next set. I wasn't expecting to have to buy new brake pads so soon - I guess that is the reality of driving on the track, especially now that the car is becoming proper fast.
06YarisRSFredericton, New Brunswick, Canada · Jun 16, 2019#209
Revisiting the EBay gauge pod. I know, Trevor, that it didn't work for your sedan despite the listing saying that it would fit. I took many pics of the A-pillar cover in my '08 and '06 and this aftermarket A-piller looks very similar at every point. In my pic below, you can see that the Sedan has a very different A-Piller design than the hatch. Even though it looks as though they have tried to recreate the actual pillar, I would expect some fit and finish issues as well as having to figure out a way to attach the pod. Also, it's much shinier than my OEM pillar. I could adjust for that with a satin of flat clearcoat. I'm thinking I might order this pod, keeping in mind that some adjustments may have to be made. I'm not finding other locations in the car to mount gauges that are appealing to me. I could drill my driver's side upper glove box, but not really into that.

Picture not included in this copy
tmontagueThread starterCaledonia Ont. · Jun 17, 2019#210
hmm, I think you're on to something, I didn't realize the sedan has a different A pillar. It may turn out that it only fits LB's and not the sedan, either way I made it work and it has been find for me since the install.
06YarisRSFredericton, New Brunswick, Canada · Jun 17, 2019#211
Originally Posted by tmontague ↑
hmm, I think you're on to something, I didn't realize the sedan has a different A pillar. It may turn out that it only fits LB's and not the sedan, either way I made it work and it has been find for me since the install.
Haha, I hope it fits and looks ok as I just ordered it.
CrankyOldManWest Michigan · Jun 18, 2019#212
Originally Posted by 06YarisRS ↑
I'm not finding other locations in the car to mount gauges that are appealing to me.
During my supercharger build I played with a 2D laser cutter and mocked up a plastic gauge panel for the upper glovebox. It was just big enough for a ScanGauge II and two 55mm dials, but I never completed it. It's less than ideal on the track since you'd have to look that far down to see anything but it could be ok for less immediate information. There's a thread around here somewhere with my template...
06YarisRSFredericton, New Brunswick, Canada · Jun 19, 2019#213
Originally Posted by CrankyOldMan ↑
During my supercharger build I played with a 2D laser cutter and mocked up a plastic gauge panel for the upper glovebox. It was just big enough for a ScanGauge II and two 55mm dials, but I never completed it. It's less than ideal on the track since you'd have to look that far down to see anything but it could be ok for less immediate information. There's a thread around here somewhere with my template...
Sounds interesting. I'll definitely have a look around for that thread. Thanks.
CrankyOldManWest Michigan · Jun 19, 2019#214
Originally Posted by 06YarisRS ↑
Sounds interesting. I'll definitely have a look around for that thread. Thanks.
Found it. Looks like I never posted the schematics. I'll take a look in my archives tonight-ish.
tmontagueThread starterCaledonia Ont. · Jul 12, 2019#215
I've been a little MIA the past few weeks, life is very busy right now between
studying for my last two board exams, getting the house prepped to list it in early Sept, spending time with kids, wife's promotion (more work) I haven't had much time for anything else. I haven't been able to get back on the track unfortunately mainly because I need some new brake pads as mine have a questionable amount of life left in them and I don't want to wast cash on a track to only get a session or two in.

The pads I want to run will cost around $400CAD and I wasn't expecting nor do I have that kind of cash at the moment. This year was always going to be a bit iffy in terms of how much I could get out to the track as I knew I'd be focusing on my exams and selling a house but it has been a bit of a drag, especially after my new PB I set last time out on a new set up.

That said, I do have good news in regards to my track car...it can now be fully stripped and properly made light as I have always wanted it to be because...

My family and I are now owner of a new (used) 2010 Subaru Outback 3.6R limited 👍

We opted to buy a new family hauler so that I can now use my Wife's Vibe as my daily and she can drive the Outback. The Yaris was getting to be pretty rough hauling kids around when picking them up from daycare. No a/c (it's hot here now), bumpy, no storage and no insulation. I can't even talk to someone on the phone it is so loud - that was getting frustrating having to yell at people to tell them I'll call them back!

The car was sold as is with 253k km on it and needs some work which is why I was able to buy it very cheap at $3200 with winter tires - it's the limited trim with navigation which was the absolute top trim the Outback came in back in 2010. Side mirror is broken and hanging off, front windshield is cracked, passenger seat electric controls are not working, headlights foggy, one taillight is foggy from interior damage, coolant was 700ml low, engine has a ton of oil leaks/weeps but doesn't really drip on the ground, potential drivers side head gasket issues (although 200km so far and it is proving to be sound).

I purposefully bought the H6 as the real world fuel economy numbers are barely worse than the H4's and we often do trips fully loaded up to the cottage. Passing people at 80km/h on single lane rural roads was near impossible in the Vibe. They will be a breeze now. I can also now purchase a tow dolly (the Outback can tow 2700lbs legally in NA, but upwards of 3000 in Europe with the same chassis) and tow my Yaris to the track. This saves me from having to insure 3 cars - I will have to keep the Yaris plated and insured as technically 2 wheels are on the road, but I believe the insurance is much different and should cost much less as I'm not actually driving it on the road.

My Yaris should be down around 2000 lbs by the time I tow it, if not less, and the tow dolly doesn't weigh much at all.

With my family's budget, the only way to get into a large sized vehicle with luxuries like heated seat, climate control was to buy one that most people didn't want and had issues. I bought it expecting it to need a head gasket and purposefully had a number I was not going to go over. I wasn't sure it needed head gaskets, but I assumed it did. The rest of the chassis checked out surprisingly well, all axles and boots are in sound shape, suspension is all tight and there are no clunks. The rust is minimal for a 9 year old car that wasn't oil sprayed (I will be doing that soon) and the shocks/struts although old, are not rusted and are still fine.

I'm spending the next little while slowly fixing things that cause oil leaks and draining and replacing all the fluids so I have a good starting point of the cars maintenance. Subies leak, that's a fact but simple things like oil cooler o-rings are easy and cheap to replace and when they leak, they can look catastrophic.

The block needs to be soaked in degreaser and sprayed off so I can narrow down the source of the leaks. At this point the oil is actually right beside the filler neck so the leak could have been spilled oil that was never cleaned up.

Anyways, thought I'd update, hoping to get out on the track later this year, but I have lots of time to become fast. That Yaris isn't going anywhere
06YarisRSFredericton, New Brunswick, Canada · Jul 12, 2019#216
Congrats on the new to you family hauler. It sounds nice. Planning to post pics?
ern-dizCA all day · Jul 14, 2019#217
Originally Posted by 06YarisRS ↑
Congrats on the new to you family hauler. It sounds nice. Planning to post pics?
+1 on both counts
suprf1yWaterford Ontario · Jul 14, 2019#218
You're going to put your wife in a 10 year old Subaru?

You're brave man
tmontagueThread starterCaledonia Ont. · Jul 14, 2019#219
I'll post pics once I finish the safety and do a paint correction. The car was a severely neglected family hauler and the paint is a mess. Just finished cutting and polishing the headlights and covering them in 2 coats of ceramic.

I have 350km on it now and amazingly it gets the same fuel mileage as my '05 awd Vibe, except it has way more balls, seriously this 3.6 boxer engine hauls.

I get why Subaru has the reputation it has, they leak (often due to simple cheap fixes like o rings) and they have chronic head gasket issues. However, outside of that they are sound Japanese cars on par with Toyota. The electronics last the life of the car like Toyota's and their engine internals can easily go to 400k km like Toyota's.

The benefit here is they can be found used for much cheaper because of these known issues. Fix the HG or other issue and you have yourself a very reliable and more capable hauler.

The last two if my wife's family haulers were all 12 year old Toyotas that needed work. I put the time in and they all turned out super reliable, and everyone in my family can't believe the mileage and reliability we end up getting out of rock bottom prices used cars.

I have had a p0420 (cat inefficiency) code pop up (very common occasional code on Subies, and earlier on a trans code. All cleared and running fine with no hiccups, fuel trims are spot on from both banks.

I purchased this car thinking it may have a HG leak, and priced it accordingly. After 350km I am confident it does not (they are not as common on the h6's). Coolant has not dropped and coolant temps have been spot on.

This week I'll be changing some o rings and cleaning tje engine block as well as replacing all the fluids...every single one - don't think they've ever been done
tmontagueThread starterCaledonia Ont. · Aug 2, 2019#220
So the Yaris is now stripped down to nothing in the interior except a drivers seat and it is down another 100 or so lbs due to this. I currently have it taken off insurance and being stored at my in laws warehouse until me move in the winter and I can have in my garage/driveway again.

I am hoping to get it out on track one day in September and burn out what us left in my track pads and hopefully get it in the 1:24's. I would ideally like to strip the dash, HVAC and all of the no longer needed interior wiring and lose another 50 or so lbs.

Over the winter the plan will be to get rid of the side and rear windows and convert it to lexan. I will also be pulling to window motors and interior door skins to shed some more weight. The car should be sub 2k lbs by that point.

i have spent most of my "car time" lately getting my new Subie up to my family hauler standards which means, all new fluids, zero clunks, zero dashboard lights and minimal to no leaks. I also had to cut and ceramic coat the paint as it was a very neglected car

Picture not included in this copy

Picture not included in this copy

I can say that it is now complete (save for a valve cover gasket) and it is quite the road trip car. It handles infinitely better than our Vibe at the limit and it surprisingly plush over bumps. The fuel economy is similar to the Vibe but it has a much better awd system (tested on out steep gravel cottage driveway) and it has loads more power. I am very happy with another successful used car purchase and a happy new Subie owner. They really do handle really well for the type of car they are compared to others in its class. This is also one of the softest handling generations of the Outback and I still feel it handles well.

I have had to seasoned mechanics look over the undercarriage of the car (i originally did this as well before I purchased it) and both have said that it checks out great and is in great condition. Also the rear end alignment was all within factory spec which is great as nothing has been damaged or bent. It is always good to hear actual mechanics confirms your findings seeing as I am a simple driveway wrench and not a professional by any means.

Here is a short list of things that were wrong with the car but are now all fixed:
-P0420 code (catylitic converter sub optimal efficiency)
-C0071 steering angle sensor code (effectively disabling the stability control and lighting up the dashboard)
-cracked windshield
-broken passenger side mirror
-passenger seat electric adjustments not working
-broken front control arm bushings
-leaking oil cooler o-ring
-intermittent horn engagement (this was a fun one!)
-very badly scratched paint
-bad passenger front brake shudder
-bad smell in cabin
-severely delayed throttle response
-a/c not blowing as cool as it should

I am thinking I will write a thread up some day of how I go about purchasing used vehicles and what I look for as well as how I determine the price I'm willing to pay to have a relatively inexpensive but safe car. Let me know if anyone would be interested in reading something like that in the near future. It may help other mechanically inclined people who don't have a large budget but want a nice vehicle.

For next season I plan to use the Subie to tow my Yaris to and from the track, it should make for a much faster track car when all of the niceties are stripped out of it
ern-dizCA all day · Aug 2, 2019#221
Lovely! Looking even more forward to that burn-off-the-last-of-the-track-pads update.
tmontagueThread starterCaledonia Ont. · Sep 9, 2019#222
After my decision to buy a new family hauler I was stuck with storing my Yaris at the back of my in laws business. It is only 20 mins away but with prepping the house for selling (gets listed this week), fixing up the Subie, spending time with the family and studying for board exams - I didn't really have much time to go work on it.

Plus I don't have the cash right now to drop on new brake pads so that made track days out of the question for the season. Over the past week my (almost) 3 year old son and I have been going to work on the "race car" and trying to lighten it up, he absolutely loves wrenching with me. I recently stripped out the dash and the HVAC which all in all was surprisingly heavy. I had fully gutted the interior before I drove it to storage so the pics you see below is in its current state.

Picture not included in this copy

I have to now find the proper heater hose size and buy a length of hose to loop from the two connections on the block so the heater core by pass is fully finished.

The next time I go out to work on the car I will be separating and removing any excess electrical wiring and connectors such as the airbag system and HVAC wiring. There is a huge amount of wiring under the dash and most of it is now moot. Once our family moves into a new house I will be bringing the Yaris with me to store it in a garage. Over the winter I plan on replacing all the side and rear glass with lexan to further strip some more weight off of it.

The end goal is a sub 2000lbs yaris. Keep in mind with the removal of the window glass comes the removal of all the heavy motors as well.

I plan on heading out to the track on the last Friday of September as long as the weather holds up. I'll be driving the car out there and aiming for a sub 1:25. I just hope what little I have left on the brakes will hold up.

*I forgot to mention my plan for future windshield defogging if needed. Bimmerworld sells a $100 kit that is clear defroster wires that I can wire up right off of the battery with a switch that works similar to your rear defroster wires. This IMO is a perfect solution as it is light weight and would be very effective. I likely won't need this until I start doing time attack in rain or shine in the future as I am mostly only tracking in warm temps without rain currently. It didn't make sense to keep all of the HVAC just for defogging purposes.

Picture not included in this copy

Picture not included in this copy
CrankyOldManWest Michigan · Sep 10, 2019#223
Originally Posted by tmontague ↑
So the Yaris is now stripped down to nothing in the interior except a drivers seat and it is down another 100 or so lbs due to this.
...
I would ideally like to strip the dash, HVAC and all of the no longer needed interior wiring and lose another 50 or so lbs.
...
Over the winter the plan will be to get rid of the side and rear windows and convert it to lexan. I will also be pulling to window motors and interior door skins to shed some more weight. The car should be sub 2k lbs by that point.
That's where the 2ZR Vios is right now, minus the rear window, plus the passenger OEM seat. Sub-2000 lbs is crazy quick off the line!

I'm still reading the rules for the SCCA class I want to run in (eventually) and some of the excessive weight shedding already done to mine may be outside of what's allowed. If you're interested in swapping doors and saving yourself the labor I think I can schedule a road trip.

*EDIT - that's a cool idea for the windshield. I was going to try and reinstall the OEM fan and heater core on mine.
LeegamerAshland, VA · Sep 10, 2019#224
At this point you may as well just make your own harness.

That bimmerworld defroster is a game changer. I think I will use that in my Z31, so thanks!
CrankyOldManWest Michigan · Sep 10, 2019#225
Originally Posted by tmontague ↑
The next time I go out to work on the car I will be separating and removing any excess electrical wiring and connectors such as the airbag system and HVAC wiring. There is a huge amount of wiring under the dash and most of it is now moot.
I'm going to look into the dash wires on mine this winter as well. Maybe we can do up a spreadsheet? The SRS/Airbag stuff is all gone already but I'll inventory all the remaining wires and see what can be removed. I'm also considering removing the key switch and steering wheel lock since it's not going to go on the road ever again. Headlights can go too, I think, but they're already pretty light. Not much weight savings compared to steel and glass on some older cars.
CrankyOldManWest Michigan · Sep 10, 2019#226
Originally Posted by Leegamer ↑
At this point you may as well just make your own harness.

That bimmerworld defroster is a game changer. I think I will use that in my Z31, so thanks!
ArmstrongRacing was looking into making a custom harness for his but didn't get it off the ground. I've got access to a lot of OEM crimp tools at work and can probably make something very professional looking for significantly less cost than even the tools.

The one on Bimmerworld comes directly from FrostFighter.
tmontagueThread starterCaledonia Ont. · Sep 10, 2019#227
Originally Posted by CrankyOldMan ↑
That's where the 2ZR Vios is right now, minus the rear window, plus the passenger OEM seat. Sub-2000 lbs is crazy quick off the line!

I'm still reading the rules for the SCCA class I want to run in (eventually) and some of the excessive weight shedding already done to mine may be outside of what's allowed. If you're interested in swapping doors and saving yourself the labour I think I can schedule a road trip.

When I went to the track for the first time this year after removing 150lbs out of my car I couldn't believe how noticeable the difference was. Not so much in straight line acceleration (although I'm sure that was improved too) but more so in the tight technical twisty back to back turns. The car seemed more "flickable" as if you could just rotate it and point it to where you wanted it to go. The chassis has much less weight and dive into corners so it was much happier to abruptly change direction and go where you wanted it to. The understeer also didn't feel as heavy if that makes sense.

*EDIT - that's a cool idea for the windshield. I was going to try and reinstall the OEM fan and heater core on mine.
Hmm, that might actually be a really god idea seeing as lexan isn't exactly cheap. I don't particularly want different coloured doors but at this point i'm not too concerned about looks. Mine still have all of the electrical hooked up, just no interior door cards.

IMO it is the best solution for windshield for a dedicated track rat. I contemplated keeping the OEM heater box for the defrost option, but it weighed way too much to keep around for a couple times of use. The heater wires from BW are extremely light and very effective. These are the ones I plan on using when need be https://www.bimmerworld.com/Safety-R...oster-Kit.html

Originally Posted by Leegamer ↑
At this point you may as well just make your own harness.

That bimmerworld defroster is a game changer. I think I will use that in my Z31, so thanks!
Agreed, I was extremely happy to stumble across them online. Before finding this I never saw a good solution that actually seemed effective other than the heavy and bulky OEM defroster

I am probably at that point with the harness but this is new territory for me so my plan is to slowly separate the harness and remove what isn't needed. I eventually plan to go with a standalone ECU but I still need the OEM ECU and wiring for the throttle control, ABS, tach and spedometer so I don't want to mess any of that up.

Most of the wiring in the above pictures is likely now obsolete and I'm sure a lot of it will be gone once I clear through it all.

Originally Posted by CrankyOldMan ↑
I'm going to look into the dash wires on mine this winter as well. Maybe we can do up a spreadsheet? The SRS/Airbag stuff is all gone already but I'll inventory all the remaining wires and see what can be removed. I'm also considering removing the key switch and steering wheel lock since it's not going to go on the road ever again. Headlights can go too, I think, but they're already pretty light. Not much weight savings compared to steel and glass on some older cars.
agreed, I'm going to leave my lights in for now. I though about the steering lock and key switch but since I plan to tow dolly my car I think the steering lock with prove useful for the time being.
CrankyOldManWest Michigan · Sep 10, 2019#228
Originally Posted by tmontague ↑
Hmm, that might actually be a really god idea seeing as lexan isn't exactly cheap. I don't particularly want different coloured doors but at this point i'm not too concerned about looks. Mine still have all of the electrical hooked up, just no interior door cards.

...

agreed, I'm going to leave my lights in for now. I though about the steering lock and key switch but since I plan to tow dolly my car I think the steering lock with prove useful for the time being.
Is yours black sand pearl? I found some doors in decent shape at a local yard but they're blue. The paint on the roof and trunk are in desperate need of repair anyway so it's going to get repainted at some point. My passenger rear door is dented as well.

Good point about the tow dolly. I intend to trailer mine and save the tires. =)
tmontagueThread starterCaledonia Ont. · Sep 10, 2019#229
no my paint color is flint mica paint code 1E0
CrankyOldManWest Michigan · Sep 10, 2019#230
Originally Posted by tmontague ↑
no my paint color is flint mica paint code 1E0
Aah, yeah, that would look a little odd.
tmontagueThread starterCaledonia Ont. · Sep 16, 2019#231
I've been spending some time each weekday evening an hour here or there with my son slowly stripping the car down to only the necessities.

Picture not included in this copy

Part of that was the removal of the heater core which leaves me with 2 open coolant hoses at the firewall. Easiest way to solve this is to just buy a 5/8" hose connection and fit them together. Well I did that, and it leaked, non stop drip as soon as the coolant built up pressure. I bought a Dorman 90 degree plastic 5/8-5/8" barbed elbow and even with the oem clamps put on the fittings it still leaked.

That is silicone (dielectric) grease on the fitting to make install and future removal easier, turns out they slide on easy...too easy
Picture not included in this copy

After looking at the original 11 year old heater hoses it was clear why they leaked. They had stretched much larger then their original diameter

Picture not included in this copy

I never liked the idea of an extra joint in the heater hose as this car sees high temps on the track and the less joints I can have the less likely leaks will happen. I ended up purchasing some 5/8" heater hose from my local CT as well as 3 EZ coils. The hose need to essentially turn 270* to go from one fitting to the other on the block. This cost about $45 total and wasn't the cheapest solution, but one that I felt I could trust when going 10/10ths in the middle of summer.

Picture not included in this copy

Picture not included in this copy

As you can see it did an extremely good job of creating 90 degree bends in a straight hose and it is a much cleaner and reliable set up than what I originally had

Picture not included in this copy

Here is the final product, no hoses are touching and have room to move with the engine. They actually are surprisingly sturdy and do not bounce around. The metal springs give it some strength and the hose is very strong.

Picture not included in this copy

Picture not included in this copy

As always I sprayed the inside of the hose ends with silicone lube before install, this has proven itself very effective much later down the road when you need to remove them.

If you ever need to do a heater core bypass for any reason, *DO NOT JUST CAP THE FITTINGS AT THE BLOCK*
the coolant flow as shown in the diagram below shows a true flow through design. The coolant needs to flow from one fitting to the other it is not a simple outflow design from both fittings.

Picture not included in this copy

I am slowly working my way through the electrical. I am currently trying isolate all of the rear wires as I am pretty sure the only ones I need are the abs, rear lights and fuel pump wires. The rest will be stripped out as lean as possible, meaning all relays will be going as well.

Not only does this make the car lighter, but more importantly it makes it much easier to diagnose future problems as there is minimal wiring to sort through.

I have isolated the airbag wires up to the front of the car and once i get done with the rear, I will be starting to separate them from the main dash board harness. There is a huge amount of wiring in this not so modern car and most of it is now obsolete as most of it is from the airbag sensors and climate control functions.

I also have to look at the factory repair manual to see what modules can be thrown out. I have already removed the small airbag ones but there is a large bulky one directly in front of the steering wheel that I suspect is the immobilizer ECU which is currently useless and bypassed anyways. I have always loved a simple car, so much easier to work on so this is making me feel very satisfied.

As a side, my wife and I have just conditionally sold out home and our next one will have a single car garage at the very least so I will eventually have my track car back at home with me again before the winter comes!
CrankyOldManWest Michigan · Sep 17, 2019#232
Originally Posted by tmontague ↑
I also have to look at the factory repair manual to see what modules can be thrown out. I have already removed the small airbag ones but there is a large bulky one directly in front of the steering wheel that I suspect is the immobilizer ECU which is currently useless and bypassed anyways.
The power steering controller is right above the column, on top of and slightly forward of the metal tube. It's a big metal box with heavy gauge wires.

1 attachment not included in this copy

tmontagueThread starterCaledonia Ont. · Sep 17, 2019#233
Yuuup that's the one, looks like I'll be keeping that. According to others who have tracked their yaris, the power steering is much more beneficial to be left in.

Thanks Sam!
ern-dizCA all day · Sep 17, 2019#234
Little man looking like he's having a great time with his pops. Just awesome.
tmontagueThread starterCaledonia Ont. · Sep 25, 2019#235
Excellent I appreciate your input having used it first hand. How did the install go assuming you installed it when the windshield was already installed on the car?

I've done a fair amount if wiring on cars in the past but I'm curious if you wired it directly off the battery with an inline fuse or what you found was the best?
tmontagueThread starterCaledonia Ont. · Oct 8, 2019#236
I headed out with Ron and the crew for the last session of the year at TMP this past Friday. It was only my second track day of the year due to finances and the crazyness of life. I actually had not been to the track for a few months this year and my Yaris has sat in the back of a warehouse for that time.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

I had started decluttering the wiring a few weeks ago as I was itching to work on my car and had the help of my son to do this. This was a much bigger project than I had anticipated and I was not able to properly finish it before the track day. I ended up semi finishing it and just tucking everything away so I could still drive around the track. In all this haste I ended up cutting and removing a few extra wires and my speedometer wasn't functioning. This only really mattered on the drive to the track as I don't really look at my speedometer much while on the track.

Picture not included in this copy

Picture not included in this copy

I have since fixed the speedometer after pouring over some EWD's and finding the respective wire that was missing and reconnecting it to the speed sensor wire. I currently don't have any dash illumination and my oil pressure light and CEL are not working. I'm still not sure if I will be reconnecting these as it really isn't useful for me at this point with what the car is used for.

I ended up removing about 2 piles of wired this big...

Picture not included in this copy

Anyways - the last time at TMP I managed to do a PB of a 1:26:44 which I was very happy with. I knew there was more time in the car as this was on a new tire set up and I was starting to push the brake pads outside of their limit as they were mildly fading and lacking that sharp bite at every brake zone.

I had very little left on my track pads and wasn't sure how much time I would have on them for the last lapping day of the season. I was hoping for a faster lap time but realistically didn't think it was going to happen. I did a quick 6 or so lap warm up session and then set tire pressures (fwiw I run a 30 psi rear and a 31 psi FR and a 34psi FL hot pressure). I headed out for a 20 minute second session and was very sloppy with my footwork. It had been a while and I wasn't feeling very confident in my sharpness. I managed a 1:27 in that session.

I headed out for my 3rd (and last) session of the night and started out by following Ron and his buddy in the two cup cars while I warmed up. There is nothing more fun on the track than chasing around two excellent drivers in these cup cars! They drove the pi$s out of them, one wheel in the air, then two, locking tires, sliding etc it was a wack of fun and helped me get my confidence back to over drive my car. They pointed me by and I just set out to have fun.

I started gaining confidence each lap and my footwork and braking zones drastically improved. My lap timer was showing that I was taking seconds off on some laps. I started pushing the limit in the big corners and the car reacted very well and in control. I was working my ass off to keep the car pointed where I wanted it to go, but it was getting faster. The track at this time was very quiet as most people went home so I decided to send it. I ended up turning a 1:24:98 on my last lap! I ended up pulling in because my brakes started making noise as if they were onto the backing plates. I was actually getting faster and faster every lap.

I removed the brake pads and sure enough it was virtually down to the plates, calling an end to the season on brake pads that owed me nothing else. I was extremely happy with a 1:24, check out Speed Academy's lap board to get some insight into lap time at TMP https://speed.academy/speed-academy-...e-leaderboard/

All those times are completed by Dave Pratt (sp?) who has over 15 years of driving at TMP and it a very fast driver - essentially as fast as most can expect to go in each lap time he has complete. On most lapping days at TMP a decent track day bro in an STI will throw down a 1:27 so a 1:24 in a Yaris is pretty darn fun.

The car ran flawlessly, it was a cool day (ambient around 10*C), oil temps sat around 230 and peaked at 240*F, coolant hovered around 195*F and peaked at 202*F. The AR-1 tires are phenomenal especially given their price range. They handled the continuous laps without becoming greasy and their wear is respectable. They actually felt faster and faster late into my sessions, meaning they probably could have stood to use some more heat in them. They also are not outright slick when cold like the BFG R1's were.

All in all I am very pleased with how the season ended even though the season was a bit of a write off in terms of track time. My plans for next season are to get a tow dolly, replace all of the side and rear glass with lexan so I can remove the inner door skins and heavy window motors. I will be getting a new set of more aggressive brake pads and adding in front windshield defrosters. I also plan on finalising the wiring and removing useless wiring from the engine bay and fuse blocks. The cabin wiring is almost done, but I need to properly mount the wiring so it is not just hanging around.

My wife and I recently purchased a new home that has a 12' wide single car garage that is heated and insulated. This is large enough to keep all of my car tools in there as well as store my Yaris. I'll finally be able to work on the Yaris as I please, even if it is just for an hour or so. No more commuting and bringing tools to go work on it!
06YarisRSFredericton, New Brunswick, Canada · Oct 9, 2019#237
You gotta stop this talk! LOL! It's making me want to do some tire and suspension work on my car!

I know virtually nothing about racing, but I looked at the Speed Academy link and you pretty much tied the time of a Subaru WRX STI. Surely the STI would make significantly better times on the straightaways, so your little Yaris must be making it up in the turns. Of course driver skill would come into play as well. Is this a logical thought process? If so, wow, that is testimony to how well your car handles and the work you've done to get it there! If I'm wrong, feel free to correct me in my thought processes.

I don't know what it is about WRX's but that's the car - in its weakest and stock variant - that I'd love to be able to beat with my car. It looks like the average 0 - 60 for the various models of WRX is around 6s. I'd never be able to achieve that, especially without an LSD, but I did manage to raise the eyebrows of a WRX driver the other day. I noticed a (I think ~2012) WRX gaining on me in the distance and I was behind another car. I was cruising around 120 km/h, so with the Subaru a reasonable distance behind me, I pulled out from behind the car in front of me and matted it. I was up to 170 pretty fast. I slowed back to 120 and the Subaru cruised past me, the driver looking over with a grin on his face. He didn't speed up but I think he definitely appreciated how quick the little 'silver bullet' econobox in front of him took off. I think 7s might be possible in my car with better tires, but 6s? NEVER without an LSD, built engine, better trans and significantly more boost. As it sits, I lose time in first and second as it really wants to spin its tires.
tmontagueThread starterCaledonia Ont. · Oct 10, 2019#238
Originally Posted by 06YarisRS ↑
You gotta stop this talk! LOL! It's making me want to do some tire and suspension work on my car!

I know virtually nothing about racing, but I looked at the Speed Academy link and you pretty much tied the time of a Subaru WRX STI. Surely the STI would make significantly better times on the straightaways, so your little Yaris must be making it up in the turns. Of course driver skill would come into play as well. Is this a logical thought process? If so, wow, that is testimony to how well your car handles and the work you've done to get it there! If I'm wrong, feel free to correct me in my thought processes.

I don't know what it is about WRX's but that's the car - in its weakest and stock variant - that I'd love to be able to beat with my car. It looks like the average 0 - 60 for the various models of WRX is around 6s. I'd never be able to achieve that, especially without an LSD, but I did manage to raise the eyebrows of a WRX driver the other day. I noticed a (I think ~2012) WRX gaining on me in the distance and I was behind another car. I was cruising around 120 km/h, so with the Subaru a reasonable distance behind me, I pulled out from behind the car in front of me and matted it. I was up to 170 pretty fast. I slowed back to 120 and the Subaru cruised past me, the driver looking over with a grin on his face. He didn't speed up but I think he definitely appreciated how quick the little 'silver bullet' econobox in front of him took off. I think 7s might be possible in my car with better tires, but 6s? NEVER without an LSD, built engine, better trans and significantly more boost. As it sits, I lose time in first and second as it really wants to spin its tires.
lol definitely do tires first, but that of course will let you down the road of suspension. IMHO I would recommend 340TW BFG G-force sport comp 2's on your set up. You will never realistically (or safely) push past their limit on public roads and they are phenomenal and predictable in the wet. Anything more than simple lowering springs and slightly stiffer dampers would start to make you regret your decision over time...trust me I have been down that road and I was ok with it because my cars was becoming a dedicated track car but therre is no way I would have been dailying it much longer.

An LSD won't help you too much in a straight line at least not width typical Yaris tires. I still spin my tires if I take off from a dead stop with sticky tires at anything close to WOT. The LSD in my experience is the most beneficial when at the absolute limit of grip in the corners and you want to put down the throttle. It actually helps you pull forward and steer your car through the corners. Also really helps you control a snap oversteer by throttling out of it whereas an open diff will just spin the inside tire. The better driver I become the most I appreciate the clutch type diff.

Dave at Speed Academy is by far a better/more experienced driver than me so put those times in perspective...to be fair though he also doesn't have a ton of seat time in some of those cars he did laps on. The cars that they built he has a ton of seat time in, but some of the lap times are on viewers cars that he does a few hot laps in.

The 2016 STI no doubts pulls harder and faster in the straights however TMP is a track that is considered relatively low speed, very tight and extremely hard on brakes. It favours momentum cars or at least better drivers as there are less places to simply got WOT in a straight to make up for poor cornering and poor driver skill.

My car and myself are much faster on the infield at TMP as I can carry more speed through the turns and the Yaris transitions from corner to corner much better. Much of this has to do with the low weight of the Yaris compared to the STI - the Yaris is much more "flickable" side to side and part of which makes it such a blast to drive. Keep in mind my Yaris is still only putting down somewhere in the ball park of 138ish whp.

There is no doubt that the Yaris is being driven past its limits compared to many other big power cars at TMP. According to spectators they Yaris and cup cars are a blast to watch as they are screeching around corners and lifting wheels where as the other cars typically are much more cautious.
06YarisRSFredericton, New Brunswick, Canada · Oct 11, 2019#239
Originally Posted by tmontague ↑
lol definitely do tires first, but that of course will let you down the road of suspension. IMHO I would recommend 340TW BFG G-force sport comp 2's on your set up. You will never realistically (or safely) push past their limit on public roads and they are phenomenal and predictable in the wet. Anything more than simple lowering springs and slightly stiffer dampers would start to make you regret your decision over time...trust me I have been down that road and I was ok with it because my cars was becoming a dedicated track car but therre is no way I would have been dailying it much longer.

An LSD won't help you too much in a straight line at least not width typical Yaris tires. I still spin my tires if I take off from a dead stop with sticky tires at anything close to WOT. The LSD in my experience is the most beneficial when at the absolute limit of grip in the corners and you want to put down the throttle. It actually helps you pull forward and steer your car through the corners. Also really helps you control a snap oversteer by throttling out of it whereas an open diff will just spin the inside tire. The better driver I become the most I appreciate the clutch type diff.

Dave at Speed Academy is by far a better/more experienced driver than me so put those times in perspective...to be fair though he also doesn't have a ton of seat time in some of those cars he did laps on. The cars that they built he has a ton of seat time in, but some of the lap times are on viewers cars that he does a few hot laps in.

The 2016 STI no doubts pulls harder and faster in the straights however TMP is a track that is considered relatively low speed, very tight and extremely hard on brakes. It favours momentum cars or at least better drivers as there are less places to simply got WOT in a straight to make up for poor cornering and poor driver skill.

My car and myself are much faster on the infield at TMP as I can carry more speed through the turns and the Yaris transitions from corner to corner much better. Much of this has to do with the low weight of the Yaris compared to the STI - the Yaris is much more "flickable" side to side and part of which makes it such a blast to drive. Keep in mind my Yaris is still only putting down somewhere in the ball park of 138ish whp.

There is no doubt that the Yaris is being driven past its limits compared to many other big power cars at TMP. According to spectators they Yaris and cup cars are a blast to watch as they are screeching around corners and lifting wheels where as the other cars typically are much more cautious.
I checked out the Sport Comps. The smallest size is 195/50R15. Unfortunately this is out of spec for my factory alloys which is what I intend to keep on the car. I do actually have 195/60R15s on the car now, but there's a bit of sidewall bulge. It still handles well and the tires won't come off, I think, under extreme cornering, but it might defeat the purpose of the performance tire. A.K.A. I might not reap the benefits of such a great performance tire. Also, with the lower side wall height of the Sport Comp, the sidewall deformation might even be exaggerated.

Yeah, I might not see a lot of benefit from an LSD, and certainly wouldn't be worth the hassle and expense of installing one on this auto trans, although I believe there migh be one available. I know though that I could improve my 0 - 60 time without the amount of wheel spin I get. I'd really love get close to 6s, pipe dream, I know. I'm pretty sure that 7s might be attainable with the right launch as the car sits.
tmontagueThread starterCaledonia Ont. · Oct 12, 2019#240
Originally Posted by 06YarisRS ↑
I checked out the Sport Comps. The smallest size is 195/50R15. Unfortunately this is out of spec for my factory alloys which is what I intend to keep on the car. I do actually have 195/60R15s on the car now, but there's a bit of sidewall bulge. It still handles well and the tires won't come off, I think, under extreme cornering, but it might defeat the purpose of the performance tire. A.K.A. I might not reap the benefits of such a great performance tire. Also, with the lower side wall height of the Sport Comp, the sidewall deformation might even be exaggerated.

Yeah, I might not see a lot of benefit from an LSD, and certainly wouldn't be worth the hassle and expense of installing one on this auto trans, although I believe there migh be one available. I know though that I could improve my 0 - 60 time without the amount of wheel spin I get. I'd really love get close to 6s, pipe dream, I know. I'm pretty sure that 7s might be attainable with the right launch as the car sits.
I don't remember the exact specs of the factory rims but I cannot imagine the BFG's in the above size should cause any problems even under extreme cornering. Realistically the tire will start to give way before the bead and rim do. It is only a 340tw and even though it isd a sticky 340 it will not perform anywhere close to Hoosier slicks.

a 6sec 0-60 would be pretty nuts in a Yaris, but at the end of the day it's all a balance of cost and what it would cost to do a 6sec 0-60 would likely be quite a bit. Only you can make that decision but if you don't have plans to run the car at a drag strip or race it that price can be quite steep just for the sake of knowing it can run that fast. Like I said that is a decision only you can make as the owner and person who is actually paying to do everything to the car. It would be pretty wild though👍
tmontagueThread starterCaledonia Ont. · Oct 12, 2019#241
A couple days after the last track event I drove my car the short 20 min drive back to where I store it or at least will be storing it up until I move to a new house mid November. I run a 10% coolant to water mix with Amsoil coolant booster during the summer. The 10% coolant is to aid in adding some amount of lubrication as well as a moderate freeze protection in case of a flash freeze in the spring/fall. According to my coolant tester it is good to about -18*C which is pretty good. I have a few litres of this mix left and will use it up but eventually will switch to a 30/70 coolant/water mix as I don't have the coolant temp issues I used to have since I went with a performance radiator set up.

With my new radiator set up the filler neck is now below the top of the engine block. Simply raising the front of the car up doesn't allow the filler neck to get to the highest point anymore. The easiest solution if to get a pressure filler and a cheaper option is a Lisle spill free funnel which I will likely pick up for next season. But for now I have found if I jack up the passenger side as high as I can (the side the filler neck is on) and spend about 10 mins squeezing the lower rad hose, I can get a bunch of air to get out of the system. I then let it idle up to operating temps before driving it and let it cool down and depressurise and typically this causes no issue when doing this before a track day.


The other day I had an issue, a potentially big one. I drained and filled the race coolant with my typical 55/45 coolant/water winter mix I have in all of my cars. I didn't spend any time squeezing the rad hoses of letting the car idle. I simply lifted the one side of the car and re filled the coolant. I was in a bit of a rush as I had to get the car to the warehouse as I only had it insured for another day so I could drive it on the street. As I started to drive it I noticed the coolant going above the typical 190-195*F, and it was a cool day (~15*C ambient). It started going to 200 then 204 and up. I got onto the highway and opened it up a bit, the coolant started climbing and got into 240 and then 244*F. At 240* the red temp light started to flash. I immediately back off and cruised and noticed the coolant start to immediate lower. Then after another 30 secs it started dropping rapidly to 190*F, this meant the Tstat finally opened.

I drove like this for another few mins and then tried getting on the gas again a bit. This started to happen again when revs for above 4k. I back off when I saw the temp go above 230*F. The boiling point of the coolant is north of 255*F so I wasn't too worried about boiling over but I was worried about damage to the head at those temps.

Likely what happened was the following: Air still in system and eventually found its way to the Tsat therefore stopping it from opening. Coolant temp at the head climbed and climbed as there was no flow to the rad. This was made worse at high revs as this causes higher engine temps. I also think that the higher rpm may have caused the problem to become larger by the faster spinning water pump potentially moving the air bubbles towards the Tsat (not fully sure).

Before I drive it again I will jack up the passenger side, remove the rad cap and squeeze the lower rad hose to make the jiggle pin jiggle. If I remove the rad cap with the car flat on the ground 300mls of coolant will plummet out even when it isn't under pressure due to the coolant neck being below the highest point of the system.

Eventually I will use the Lisle spill free funnel and with that attached to the filler neck and the passenger side raised it will become the highest point of the system by a long shot and it should make this job much easier to do in the future.
suprf1yWaterford Ontario · Oct 12, 2019#242
Originally Posted by 06YarisRS ↑
Unfortunately this is out of spec for my factory alloys
So are track days.

If you're going to be tracking you're gong to have to stop thinking like that
CrankyOldManWest Michigan · Oct 15, 2019#243
Congrats! Super stoked to see you getting back in to the groove.

The hoarder in me wants to keep those wire harnesses "just in case I need them", but good on you for sorting them out!
06YarisRSFredericton, New Brunswick, Canada · Oct 15, 2019#244
Originally Posted by tmontague ↑
I don't remember the exact specs of the factory rims but I cannot imagine the BFG's in the above size should cause any problems even under extreme cornering. Realistically the tire will start to give way before the bead and rim do. It is only a 340tw and even though it isd a sticky 340 it will not perform anywhere close to Hoosier slicks.

a 6sec 0-60 would be pretty nuts in a Yaris, but at the end of the day it's all a balance of cost and what it would cost to do a 6sec 0-60 would likely be quite a bit. Only you can make that decision but if you don't have plans to run the car at a drag strip or race it that price can be quite steep just for the sake of knowing it can run that fast. Like I said that is a decision only you can make as the owner and person who is actually paying to do everything to the car. It would be pretty wild though👍
So you're pretty convinced that I'd be ok with the Sport Comps on my 5.5" rims? Do you have any other brand suggestions for a 195/55R15 tire before I get deeped into this? I've been turning a little sharper lately and there doesn't seem to be any adverse handling even with the cheap tires I have on the car which are 195/60R15s. I think a 55 tire might improve handling a bit, especially if it had a stiffer wall. Here is a comparison between my current tires and a 55 tire. I might notice a tiny bit better acceleration as well with the slightly smaller tire diameter. What I'd really like is a 205 or 215 tire but that would definitely necessitate wider wheels. 🙁

Picture not included in this copy
tmontagueThread starterCaledonia Ont. · Oct 16, 2019#245
Originally Posted by CrankyOldMan ↑
Congrats! Super stoked to see you getting back in to the groove.

The hoarder in me wants to keep those wire harnesses "just in case I need them", but good on you for sorting them out!
Thanks Sam - FWIW I have kept all of the electrical that I stripped out. plan on keeping it in a bin in case I need pins or connectors in the future. I have already used some of it when I needed wire to fix the speedometer and dash warning lights.

Originally Posted by 06YarisRS ↑
So you're pretty convinced that I'd be ok with the Sport Comps on my 5.5" rims? Do you have any other brand suggestions for a 195/55R15 tire before I get deeped into this? I've been turning a little sharper lately and there doesn't seem to be any adverse handling even with the cheap tires I have on the car which are 195/60R15s. I think a 55 tire might improve handling a bit, especially if it had a stiffer wall. Here is a comparison between my current tires and a 55 tire. I might notice a tiny bit better acceleration as well with the slightly smaller tire diameter. What I'd really like is a 205 or 215 tire but that would definitely necessitate wider wheels. 🙁

Picture not included in this copy
The BFG's should be fine on a 5.5" wide, it is at the limit but won't negate the benefit of those tires, they are fairly stiff and perform very well in wet conditions with a very predictable breakaway.

That said, I don't know if you really would benefit from shelling out cash for the tires right now if you are not finding the limits of your current rubber. They will just wear out faster than your current set up without utilising their full potential
06YarisRSFredericton, New Brunswick, Canada · Oct 18, 2019#246
Originally Posted by tmontague ↑
The BFG's should be fine on a 5.5" wide, it is at the limit but won't negate the benefit of those tires, they are fairly stiff and perform very well in wet conditions with a very predictable breakaway.

That said, I don't know if you really would benefit from shelling out cash for the tires right now if you are not finding the limits of your current rubber. They will just wear out faster than your current set up without utilising their full potential
You might be right. The tires on there now make the car handle adequately, so I may just keep them until they wear down a bit. When I replace them, I'll go for a performance oriented 55 tire. If I had gobs of cash and felt like blowing it, I'd have the factoy alloys widened an inch or and inch and a half and put a nice chunky 205 or 215 tire on there. All assuming of course that there'd be the appropriate amount of clearance with the stock offset. I'm not sure how wide a tire would have to be to start degrading performance (losing traction) on such a light car as the Yaris.
myfirstyotaToronto Canada · Oct 18, 2019#247
Fwiw
I have a 205/50 R15 on the factory RS alloys. Nitto neo is the type. But the tire guy said they had a hard time seating the beads lol
06YarisRSFredericton, New Brunswick, Canada · Oct 18, 2019#248
Originally Posted by myfirstyota ↑
Fwiw
I have a 205/50 R15 on the factory RS alloys. Nitto neo is the type. But the tire guy said they had a hard time seating the beads lol
Wow! I think a 205 would look a great on the Yaris. I assumed a tire that wide on a 5.5" rim would peel off on a hard corner, or be mushy handling. Did you notice a significant difference in driving characteristics when you went with the wider tire? I suppose the lower sidewall might add some stiffness. I'm really interested in your observations.
tmontagueThread starterCaledonia Ont. · Oct 19, 2019#249
Take note that the sport comp 2's at 195 wide are the sake width as most 205 wide tires...they fit very wide. I have never had them on a stock sized rim, they have been on a 7.5 wide and 7 inch wide rim, they were very minimally stretched on the 7.5" rim. 7" was definitely much better
06YarisRSFredericton, New Brunswick, Canada · Nov 9, 2019#250
Originally Posted by tsk94 ↑
205 is pushing it for a 5.5" rim. A 195 or even a 185 would be more ideal. Once you start putting a tire that is much wider than the wheel itself, the wheel won't be able to provide the proper amount of support for the tire - especially for the sidewall.

The other comment above on how he had a hard time even getting them mounted illustrates the point as well.
Yeah, I think I'll go with 195's in a performance all season when I do replace the tires. The 195/60R15s I have on there now are a little tall for the car as it is. 55's might be just the right size. I might even eek out a wee bit more acceleration. I don't know, but maybe the slightly shorter tire will give the appearance of a bit more width as a bonus. I just wish there was a stock RS wheel made in 16 x 6.5 or 7. That, would be ideal.