tmontagueOriginal postCaledonia Ont. · Feb 9, 2017#1Alright, time for my thread to be started up. I will be starting this swap in 2 weeks during my reading week off school. I don't have a garage (just a 2 car wide short driveway) so I'm using the winter temps to not have to deal with rain. Thankfully the weather is hovering around 0-5 below Celsius so I'll hopefully avoid the "polar vortex" we had the past couple years.
Thanks to the help of the others that have already completed the swap and their willingness to pass along info, I've been able to slowly purchase the specific parts that I need.
I was able to pick up a 2zr from an auto trans '11 Corolla with 89k km on it for $600 CAD from a local yard near me. I stripped down the block and painted it to keep it clean and protect it. I installed an oil catch can as the PCV valve is hidden behind the intake manifold and it is easier to install with the engine pulled.
I'm installing a Luk Corolla clutch and aftermarket but oem weight flywheel.
My engine harness was pulled from an '08 xd m/t with a/c for an unreal price (thanks to Cranky for finding that gem and shipping me the parts). It was in great shape except for one of the engine knock sensor wires being broken. I just fixed the wire and should be good to go.
Here are the parts that I purchased for this swap - I'll add part numbers once everything it complete.
-2zr long block
-2zr a/c compressor
-2zr alternator
-xd m/t engine harness with a/c
-passenger side and driver side engine mount and bracket
-2zr clutch
-2zr flywheel
-2zr flywheel bolts
-xd maf sensor
-xd air box (top only, as yaris bottom box is compatible)
-xd top radator hose plus 4" straight piece
-xd coolant filler neck
-xd non immobilier '08 ecu (my yaris has an immo, but I'm bypassing it)
-2zr a/c compressor bolts (still unsure if 1nz bolts will also work)
-2zr timing chain tensioner gasket (commonly leaks so figured I'd change it)
-2zr drive belt for a/c
-2zr engine hooks front and rear
Picture not included in this copy
Picture not included in this copy
When I picked up my engine I put it in a stand and checked as much as I could to see what kind of shape it was in. Plugs were clean and in fine shape (iridium), cams and rockers looked clean with zero sludge under the valve cover, valves are stained but smooth and clean, oil wasn't dirty and has no metal shavings in it. Minimal rust on the bolts on the block.
My original plan was to go with the RPM long tube header and get a local exhaust shop to fabricate my current custom 2.25" exhaust to fit it. Due to the cost as well as DD drive ability (exhaust hitting firewall issues) I decided to just clean up the oem header and paint it with black ceramic paint. There is a DC header for the 2zr but online report have minimal improvements over oem. Basically, if you're going to spend the cash for an aftermarket header spend it on the RPM long tube. It just isn't as simple as a plug and play like other headers.
I'll just have the exhaust shop weld on a new ball joint flange so that it will properly fit on the 2zr header.
I'll update this thread with pics this week and I'll document how the swap goes. This is my first engine swap and I'm doing it solo (although I have the online help of others on here who have done the swap before) I have a pretty decent amount of experience working as a shade tree mechanic and I have a good amount of tools including air tools.
I'll be jacking the front of the car up and placing jack stands under the frame rails (just the front). This will allow me access to everything I'll need for the swap.
I'll be removing the front bumper, crash bar and radiator so that the engine removal and install will be much easier.
Wish me luck!
Replies 282
SirDigbyDenver, Colorado · Feb 9, 2017#2are you going to do anything with the cooling system? is the yaris radiator big enough? do you need to change fans?
why a wiring harness for a manual with an automatic transaxle?
tmontagueThread starterCaledonia Ont. · Feb 9, 2017#3The rad has proved adequate enough for use on the track and auto x as per Armstrong racing's swap and others so I'll be keeping the oem rad in. I'm pretty sure the xd has the same rad as the Yaris and the xd comes from the factory with the 2zr.
My car in a m/t so I have a harness from a m/t xd. My engine was pulled from an a/t but I've removed the pressure plate and installed a flywheel so I'll be using it as a m/t.
I'm running the oem yaris trans I'm not using the xd trans
tmontagueThread starterCaledonia Ont. · Feb 17, 2017#4Started on the car this morning for a few hours before work. Tomorrow will start my full days until it is complete. I got all the fluids drained and much of the front end off the car.
Some aftermarket wires to remove and one or two more cross braces. Then the hoses and wiring harness to be diconnexted from the body (pulling it with engine) then I'll be ready to remove the 1nz.
I should at least have the 1nz pulled by tomorrow, crossing my fingers I'll have the 2zr mounted by night fall but we'll see.
As a side, all of the bolts on the front end of my yaris were in great shape and not rusted really at all.
They were all covered in a thin film of the Krown oil, definitely will continue with this every year, makes working on a 9 year old car much easier
This is where I left off after around 3 hours.
Picture not included in this copy
My shed is all the way in the backyard which makes for long set up and clean up times as opposed to having a garage to do this in.
IllusionXBrossard, QC · Feb 17, 2017#5Oh wow! Can't wait to see the final product
Sent from my SM-G930W8 using Tapatalk
WeeYariGeorgetown, Ontario, Canada · Feb 18, 2017#6Weather Gods sure be smiling on you this weekend.
tmontagueThread starterCaledonia Ont. · Feb 18, 2017#7 Originally Posted by
WeeYari ↑ Weather Gods sure be smiling on you this weekend.
it's been unreal, planned to do it now to avoid rain and just deal with cold...turns out I don't have to deal with either!
tmontagueThread starterCaledonia Ont. · Feb 18, 2017#8First full day, spent about 11 hours including set up and clean up which was easily 1.5 hours of the day since I have to assemble to engine hoist on my drive way and then disassemble it to store it between my house (narrow space between house so I can't fit it fully assembled)
Started with clearing more of the the frame as well as lights and then all of the electrical wires and hoses etc
Picture not included in this copy
Got it to this point after a couple hours and then started assembling my hoist to pull the 1nz.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
I never ended up replacing the sway bar bushings as the oem ones are still in excellent stiff shape. I would've had to pull the steering rack to access the bolts for the bushings and it would've been a waste of valuable time
I depressurized the fuel system when I set my car up on the drive way. I just pulled the EFI2 fuse and the car shut off virtually right away. I tried pulling the EFI1 fuse but that did nothing and the car kept running (weird?)
This meant there was very little fuel spill when I diconnected the fuel line. A paper towel was more than enough to catch what little was there. I had my a/c discharged at my mechanic's shop for $40 so removing the a/c lines was no issue.
Once the 1nz was on the drive way I needed the bell housing bolts (9 in total including the 2 starter bolts) as well as the pressure plate bolts. I separated the trans from the 1nz and then got to work installing my new flywheel and clutch onto the 2zr. I also cleaned off the internals of the trans housing as well as the splines and shift fork. All the grease was gone and everything has a light coat of mild surface rust. The lack of grease is likely why I had a squeak when I depress the clutch (yes, I lubed the shift linkages and the squeak still persisted)
Picture not included in this copy
Once the flywheel was properly torqued down (38 ft/lbs and then 90 degree turn) I installed the friction disc and pressure plate (14ft/lbs) and then greased all of the contact points up. The old throwout bearing was still in decent shape but was starting to have some play in it. The new one was more solid feeling and smoother as expected.
My clutch was on it last legs...one side of the clutch was worn down about 1/4 of a mm from the rivets. Both the flywheel and pressure plate were glazed with some blueish hot spots, but there were no grooves in either surface. This likely contributed to my cold/wet morning shudder. The car has 175k km on it now and I purchased it with 87k km so I have no idea how the person before me drove it. It always shuddered occasionally when I purchased it.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
I then installed the trans to the 2zr and transferred my block heater to the 2zr while it was out of the car. I then opened the 1nz harness and grabbed the speed sensor from the connector and attached it to the 2zr harness and properly wrapped in plastic loom. I also transferred all of the hose over to the 2zr at this time.
I then installed the passenger side mount to the body and put the dog bone in and loosely tightened it so it still swiveled. The 2zr is larger so it takes some time to put in the car (especially if you do this swap solo like I am). I found that getting the dogbone mount attached to the engine first and then the passenger side mount worked best. I used an engine leveler (highly recommend it especially if you don't have help). I also used a jack under the trans to help adjust the angle of the 2zr as well. I then installed the trans mount and unhooked the hoist.
I would highly recommend who ever does this swap to do was I did and what i was told by others and that is to remove the front brackets and bracing before you pull the 1nz. I was on the fence because of how much extra time it took but I listened to people who have more engine swap experience than me (and who had already completed this swap) and I'm glad I did.
With the front end off the car you can just turn the engine 90 degrees and easily slide it out. The crash beams are very close the engine and dont give you much room so pulling the front end saves you a lot of time down the road and makes it was easier.
Picture not included in this copy
Tomorrow I'll be connecting/trimming allf of the hoses and connectors and putting the radiator back on as wll as most of the front end. I'll likely have a chance to fire it up tomorrow.
I have to take it to an exhaust shop so they can fabricate a proper mount to fit the 2zr header as the current one I have on my custom exhaust is too small. Due to the holiday Monday next week I likely won't have to car fully functioning until Tuesday evening. I may still be able to temporarily connect the exhaust flange to the header so I can drive it around, but we'll see.
As a side, I took a silicone coupling I had and cut pieces from it to jam in the dog bone and trans mount. A member on this forum posted about the idea so I tried it out. The dogbone mount is super soft and the silicone definitely tightened it up, but I wasn't able to get much in the mount as I hoped as it was a tight fit.
3cyltrboOttawa · Feb 20, 2017#9MOAR
ern-dizCA all day · Feb 20, 2017#10 Originally Posted by
3cyltrbo ↑ MOAR
+1
tmontagueThread starterCaledonia Ont. · Feb 20, 2017#11Alright so after the full day Saturday I ended up being up all night hugging a toilet, the flu isn't fun but luckily usually short lived.
I ended up sleeping most of day Sunday and just picked little bits on the car. So basically I got a couple crash bars installed and all of the vacuum, fuel and heater core hoses connected.
Started out late this morning and I got the air box installed as well as the battery mount. Then I installed the lower rad support bar, the rad and then the upper support bar. I connected all of the a/c lines and hoses to the rad and then hooked up the battery.
I unplugged the efi 2 fuse and cranked the engine to build oil pressure. After 5-10 secs (oil pressure light still hadn't turned off) I checked the engine. I had a big fuel leak coming from the 2nd or 3rd injector. I removed the fuel rail and re seated the injectors.
I then disconnected the coils and injectors and cranked the engine some more. After about 30-50 seconds the oil pressure light went off. I then went to work on the immobilizer ecu bypass voodoo. After about 5 mins that was done and it was time to start it up.
The car would crank but not fire up. This happened for about 7 times (I would only let the car crank as long as it does when you just turn the key to start and then back to ignition). Double checked that everything was connected and no wires we unplugged. Tried it again and this time it stumbled and then died.
Tried a couple more times and then finally it turned over and ran fine. Cranky and Armstrong thought this was likely due to air being in the fuel lines since I had purged them before I pulled the 1nz.
Ever since then it has started and ran with zero issues and no codes thrown. I have only driven it around the block because the noise in unbearable above 2k rpm. The mid pipe is barely attached to the header so I essentially have no exhaust from the header.
I'll be taking it to an exhaust shop tomorrow since today was a holiday and hopefully they'll have time to fabricate a proper flange for the larger donut gasket.
To put this build in perspective, if I wasn't sick the whole thing would have been done in two 11 hour days working by myself. This is probably as easy as it gets to engine swaps. Especially with the support of the guys who've done it before me.
I'll post again tomorrow with an update and I'll be driving it as soon as I can and posting a review compared to the 1nz. I'll also be posting exactly what I had to buy and what I could use from the 1nz. For example my shift cables worked fine and got without any real issues. There seems to be some slight differences from the sedan to hatch swaps.
Big thanks to those on this forum who have done the swap before and offered up so much helpful info, made this swap much more painless
ern-dizCA all day · Feb 20, 2017#12The jealousy is real!
CorbeaubleuQuebec · Feb 20, 2017#13Can we have pics of the new motor installed?
CorbeaubleuQuebec · Feb 20, 2017#14Also what exactly is included in a XD harness? Trashed Scions are way rare here.
WeeYariGeorgetown, Ontario, Canada · Feb 20, 2017#15 Originally Posted by
Corbeaubleu ↑ Trashed Scions are way rare here.
Precisely the reason why the harness used in this Canadian project was sourced out of the States.
Sent from my iPhone using Tapatalk
CrankyOldManWest Michigan · Feb 20, 2017#16Congrats on joining the Dark Side! We don't have boost yet, but there are secret plans being drawn up as we speak...
CrankyOldManWest Michigan · Feb 20, 2017#17 Originally Posted by
WeeYari ↑ Precisely the reason why the harness used in this Canadian project was sourced out of the States.
...by Cranky, from a recycler on the other side of the country, who also collected parts from an xD at his local you-pick-yard. ;)
The MT swap is something not to be attempted by the easily discouraged. I will do everything in my power to help the next person, but it may take months or even years before the right parts are available. Armstrong Racing and I are putting together a swap kit--hopefully MT--because we want to see more of these happen.
That said, the AT swap is cake. Dime a dozen for those parts, much less hassle with sourcing them. If you're a competent shade tree mechanic and willing to put in the time up front, this is easily a weekend project. Bolt in ~130 hp. OEM reliability. Done. 😁
tmontagueThread starterCaledonia Ont. · Feb 20, 2017#18I'll have pics up tomorrow, my wife got the flu I had so takin care of her and the 3 month old meant no time for pictures.
And yes, as WeeYari mentioned, I sourced the xd m/t harness from an American xd which is why it didn't have an immobilizer.
I was also fortunate that Cranky found a scrapped xd at a local "you pull" and was kind enough to pull me the parts I needed. This have me access to rare parts and also at a fraction of the cost I otherwise would have had to pay for them.
I never planned on doing the swap this early but I made things work when I saw those parts come available
CorbeaubleuQuebec · Feb 21, 2017#19So is the harness just a sub assembly of the stock harness? If so, seems like with a set of appropriate connectors we could come up with an affordable DIY install kit...
CorbeaubleuQuebec · Feb 21, 2017#20Wouldn't the Corolla ECU and MAF work?
And what about the power steering pump, the Yaris one was a bolt on?
CrankyOldManWest Michigan · Feb 21, 2017#21 Originally Posted by
Corbeaubleu ↑ So is the harness just a sub assembly of the stock harness? If so, seems like with a set of appropriate connectors we could come up with an affordable DIY install kit...
The engine bay has two separate harnesses: one that just goes to the engine and gearbox, and one that goes to the lights, wipers, ABS sensors, etc. You only need the engine harness for the swap. The xD is almost 100% pin-to-pin compatible on all connectors. The Corolla/Matrix requires a bit of rework. And "affordable" has different meaning to a lot of people. =P
Originally Posted by
Corbeaubleu ↑ Wouldn't the Corolla ECU and MAF work?
And what about the power steering pump, the Yaris one was a bolt on?
Until someone figures out how to (easily) reprogram the immobilizer to a new ECU (and vice versa) we're limited to using USA xD ECUs. The Corolla might work if you can get the keys, transponder ECM and the ECU from a single vehicle. Even then, no guarantees that all the plugs would be wired correctly, or would even have the signals/wires available.
The 2nd gen Yaris has electronic power assist. No pump and hoses needed. =)
CorbeaubleuQuebec · Feb 21, 2017#22Yup, seems like a bit of work and parts, however used harness and ECU from the scrapyard aren't cheap either!
I forgot about the electric power assist, thats one thing I didn't like about my wife's Yaris: seemed twitchy.
I'm looking to do this swap into a 2005 Echo.
CrankyOldManWest Michigan · Feb 21, 2017#23 Originally Posted by
Corbeaubleu ↑ I'm looking to do this swap into a 2005 Echo.
The reason this is so easy with the 2nd gen Yaris is because it's the same lower unibody as the xD. The 1st gen Yaris (Echo) is probably very different, and will require some serious research into parts compatibility.
CorbeaubleuQuebec · Feb 21, 2017#24Looking at Montagues first engine bay photo, the 1NZ seems to have the same clearance to the sub frame as on the Echo. I'd need a dimension from bell housing to crankshaft pulley to know for sure.
Right now, I've got reservations about the harnesses: the Echo doesnt have the same throttle body as the Yaris, so what else is different? Do we have pin code charts on this site?
CorbeaubleuQuebec · Feb 21, 2017#25I really want to try to make this work: the Echo weighs in at 2062 pounds!
WeeYariGeorgetown, Ontario, Canada · Feb 21, 2017#26 Originally Posted by
Corbeaubleu ↑ Looking at Montagues first engine bay photo, the 1NZ seems to have the same clearance to the sub frame as on the Echo. I'd need a dimension from bell housing to crankshaft pulley to know for sure.
Right now, I've got reservations about the harnesses: the Echo doesnt have the same throttle body as the Yaris, so what else is different? Do we have pin code charts on this site?
Start your own thread on this as it is its own standalone subject. OP does not need this pollution in his build thread.
Moderators should pull all the posts relevant to an Echo swap out and establish a thread for you.
CorbeaubleuQuebec · Feb 21, 2017#27Dac!
My apologies to all!
ern-dizCA all day · Feb 21, 2017#28 Originally Posted by
WeeYari ↑ Moderators should pull all the posts relevant to an Echo swap out and establish a thread for you.
Ha, good one.
tmontagueThread starterCaledonia Ont. · Feb 21, 2017#29Alright, I'm finally almost back to 100% health and so is the Vios. I currently have it fully put together in my driveway with a vacuum pump and a/c manifold gauges hooked up to it. If it holds vacuum I'll be filling it with 12 ounces of r134a and I'll have the a/c working by this evening.
Picture not included in this copy
The car has not had any issues since my last post and has always started up without any hesitation and never thrown any CEL's. I drove it to Zorro Muffler this morning since I didn't want to drive further to Budget exhaust where I was referred (by my mechanic) due to having no exhaust and risking a large ticket. I had ringing ears just after the 6km drive to Zorro. I was referred to them by my father in law and they had good reviews online about them.
They aren't the cheapest but they are all good guys well into their 50's and very knowledgeable. I had them put a proper fitting flange on my mid pipe and fix the small piece that had the single cat on it, since that piece was still the oem diameter. Now the whole exhaust is 2.25" and has a proper flange. Cost $208 out the door. Sound is slightly deeper than the 1nz but nothing hugely different.
I only gave it 50% throttle as I needed to top of the coolant and check for leaks until I go buck wild on it. My first impression just mildly driving around town is mainly that it makes the car feel like it's 700lbs lighter. Lighter touches on the throttle are needed to make the car go and it seems smoother then the 1nz (if that's even a thing). The car idles no problems and has had no hiccups as of yet.
The new Luk Corolla clutch is much nicer than the stock Yaris clutch. Makes driving much more enjoyable due to its quicker engagement and lighter/smoother pedal feel.
I have to figure out where and how I'm going to mount my oil catch can (any ideas are welcomed), I am going to add a second can from my 1nz engine just to improve its effectiveness as it is a diy can. That said, the single can has already grabbed a little oil and triple the amount of water so it's definitely doing something.
Picture not included in this copy
Picture not included in this copy
in the second pic above you can see what vacuum line I used for my vacuum gauge. I originally had it hooked up down stream from the evap purge valve so it wasn't showing proper vacuum. Once I put it right before the manifold it started working like it should.
The only gauge I currently don't have in use is my oil temp sensor (pressure works fine). The sensor won't fit in my adapter so I need to find some sort of 90 degree extension so it clears the passenger side crach bar and fits inside.
Here is a picture of how I powered my MAF to 12V ign. It's the exact same way Cranky did it and works excellent and is clean once the fuse cover is back on.
Picture not included in this copy
I also decided to purchase the xd coolant filler neck and hoses so it looked clean and I didn't have to play around with making the 1nz one's work (it is possible just more work). The xd filler neck bolts into two female threads on the yaris radiator. They will need to be tapped due to the rust they'll have. I used an M6x1.00 tap and 10mm bolts I had lying around from work I did on the Yaris a couple years ago.
Picture not included in this copy
I'm going to be hooking up my techstream to it and re writing my VIN to the ecu to aid in passing e test in Ontario. I don't have one until 2 years from now.
Does anyone know if the e test (obd check only) will show the type of car that the ECU stores or just the VIN #?
I'll post back once I do some fun runs at WOT on this bad boy. I'm sort of in shock right now with how well/easy this swap went. Like others have stated, the toughest part is finding everything you need. I guess I'm used to working on old rusted neglected cars and wrenching on mine is a dream when every bolt in antiseized and coated in a film of oil.
Oh I forgot to mention. The bottom of the airbox is cut on the front and driver side and the original passenger side hole is blocked. I have plastic 3 inch ducting coming from the drivers side fog light shroud feeding air into the bottom of the box. I also have the charcoal filter cut out. Althought not the same as a CAI, I avoid any water issues and it gives a nice sound.
WeeYariGeorgetown, Ontario, Canada · Feb 21, 2017#30Clean. Congrats.
Very hard to believe this was done in just over 2 days, solo! Be proud!
ern-dizCA all day · Feb 21, 2017#31 Originally Posted by
WeeYari ↑ Clean. Congrats.
Very hard to believe this was done in just over 2 days, solo! Be proud!
+1 🙌
Time to update that forum signature and garage!
tmontagueThread starterCaledonia Ont. · Feb 23, 2017#32Something new I've noticed with the 2zr is that it is an extremely smooth engine. I don't know if this is due to be it being a newer engine than the 1nz or if it is just a more refined engine but when you take it to redline there is no excess noise and movement like you have with the 1nz. Even when starting the engine it is quieter and moves less.
I'm off school this week so i haven't driven it very much as I don't like taking it for short trips and usually take the Vibe. I would have taken it out today for a drive since it was a crazy nice and warm sunny day but I knew if I went out to have some fun I would've worn my winter tires right down so I decided to keep it parked.
I did a few red lines pulls getting on and off the highway a couple days ago starting in second gear. What I noticed the most is that I get to speed much faster then I am used to. I look down expecting to be at 100km/h and I'm already at 120 or expecting to be at 80 and being over 100.
The 2zr also pulls hard right to redline unlike the 1nz which falls flat on its face above 5500 rpm. The power band on the 2zr is much more improved. What this means for drivability is that when taken to redline the 2zr "pushes" the car right into the next shift so you're always at top power. Whereas the 1nz "bucks" a lot due to going in an out of the optimal power, the 2zr stays right in it. This leads to much smoother fast shifts when you are red line shifting.
As a side, I've read reports online and if you miss a shift the 2zr is happy to spit it's rockers out but usually leaves the engine undamaged. I'm not sure what will happen with the 1nz but it would likely get damaged.
Now time to change the signature..
edit: someone let me know how to make my signature image smaller...its a biiiit big
CrankyOldManWest Michigan · Feb 24, 2017#33 Originally Posted by
tmontague ↑ edit: someone let me know how to make my signature image smaller...its a biiiit big
Step 1: Open Paint.
Step 2: ???
Step 3: Profit!
Like this?
Picture not included in this copy tmontagueThread starterCaledonia Ont. · Feb 24, 2017#34Thanks Cranky, computers aren't my strong suit🤷
tmontagueThread starterCaledonia Ont. · Feb 24, 2017#35I started out today with the plan to add my 1nz oil catch can inline with the new one I already ave on my 2zr. This ended up working out perfectly and I even found a nice place to securely and somewhat cleanly zip tie it to
Picture not included in this copy
Picture not included in this copy
now no rubbing and it is accessible when I need to empty the oil.
When I started the car this morning I noticed I had a CEL. Now I knew that the last ready check for the ecu was the EVAP system so I wasn't surprised when the code was a p0456 which is "EVAP control system leak detected a small leak". I had used a new non oem hose to run from the EVAP purge solenoid to the firewall EVAP line. This hose wasn't as snug as it should've been and the oem clamp wasn't strong enough to make a tight seal on it. I ended up taking one of the 2zr oem hoses and trimming it and using that instead. It was a much tighter fit and using silicone spray went on without an issue.
As a side if you are doing this swap, use silicone spray on any hose you are installing back on the engine or car. it will make removing them years down the road much easier and enjoyable, especially since they'll be in a tight cramped engine bay and ont easily accessible.
I went to my local Home Hardware and found a 45 degreen 1/8 NPT fitting with an extension. This will allow me to finally properly fit my oil temp sensor as it is too long to fit into the adapter I bought for the oil pressure sender.
Picture not included in this copy
Here you can see the large sensor (thing with yellow on it) and just below that you can see a 1/8 npt plug that i used to plug the hole meant for the temp sensor. The sensor wouldn't install since it won't go all of the way in due to clearance issue so it cannot thread.
Toyota engine blocks and oem oil pressure switches are 1/8 BSPT, and therefor you cannot just screw in any 1/8 npt fitting or you will have a leak and mess up the threads. What I did was buy an adapter that has a male 1/8 BSPT thread to screw into the 2zr block. It also has 1 female 1/8 BSPT port on it for the oem pressure switch. It also has two 1/8 NPT ports on it for my aftermarket oil pressure and temp gauges. This works fine but I needed a 45 degree adapter with extender so that the oil temp sensor would fit. I will hopefully install that tonight.
Becuase the 2zr uses an oil cartridge instead of a regular spin on type oil filter, I could not just use my sandwich plate to tap the oil sensors like I did with the 1nz. This means that my oil temps may not be very accurate, but I'll see once I install it.
As of now the oil pressure is much lower in the 2zr than the 1nz. Instead of being around 60-80 psi in the 1nz, it is around 40-60 psi in the 2zr. If you do install after market gauges make sure the sensor have seprate ground wires running form them. I had originally spliced them into one another and had inaccurate readings.
tarkusYYZ · Feb 24, 2017#36An amazing piece of work. Kudos!
Sent from my phone with Tapatalk. Please excuse any typpos.
tmontagueThread starterCaledonia Ont. · Feb 24, 2017#37Just finished installing the oil temp sensor. You can see in the image the original adapter I used and the oil pressure sender on top of it as well as the oem oil switch installed in the back of it.
I then installed the 45 degree fitting with the extender and then screwed the oil temp sensor into that
Picture not included in this copy
ArmstrongRacingSan Diego · Feb 24, 2017#38Congrats man and great work!!
tmontagueThread starterCaledonia Ont. · Mar 3, 2017#39Short update:
The ECU has went through it's full check and all of the readiness monitors are "ok" so it's safe to say there are no CEL's from the swap. I've driven around 700km on it and have been pushing it a little harder. It's been a ton of fun and even when only taking it to 3k rpm it wants to get up to speed quick.
It it a bit harder on mileage as expected. So far on winter gas and my first tank I'd say about 5-10% worse. That said, I've been driving harder and that tank had a lot of idling on it due to various things I was monitoring on the car.
I installed a Viofo A119 dashcam hardwired to my ignition and so far have been really impressed.
I'll be doing a dyno pull early this spring once my winters come off the car. The plan is to get some 2zr baseline numbers before I add a long tube header or anything else. The numbers will be higher than a complete stock swap as I have a 2.25" header back custom exhaust with one cat delete, as well as a cut out air box with no charcoal filter and ducting feeding to it. The intake won't do much to change numbers, but the exhaust definitely will have an effect.
At least it will give people some more info in regards to what numbers they can expect.
I'll be updating the first page on this thread with exact parts I needed for the swap and any tips or tricks that helped me.
3cyltrboOttawa · Mar 4, 2017#40🙌
tmontagueThread starterCaledonia Ont. · Apr 3, 2017#41Alright, short update on the 2zr now that the placebo effect is gone. How do I know the placebo effect is gone? Simple, the car feels slower then it did right when I did the swap.
The 2zr is a bit harder on gas then the 1nz (obviously). I probably get about 80 or so less km per tank. Seems to use about 0.5-0.8 L/100km more than the 1nz. I can't give exact numbers since we still have winter gas up here and the average numbers I have in my head are from my 1nz on summer gas.
The 2zr is smooth, right up to red line and it pulls hard all the way. I definitely need an LSD as WOT in first gear is almost impossible to do unless the road are dry, my tires (crappy 800 wear) are warm and I'm going straight. I also need better tires, which is something I'll be doing next summer as mine are getting worn and can't handle any rain.
I've had no issues still with any CEL's or anything else engine related. My dual oil catch cans pick up way more oil then I thought they would. They are inline so obviously the first one fills up quicker but it seems I'm catching about 2-3 ounces every 2k km or so.
I'll be installing some aftermarket stuff next week so I'll post the updates here when I'm done
ern-dizCA all day · Apr 3, 2017#42 Originally Posted by
tmontague ↑ ...The 2zr is smooth, right up to red line and it pulls hard all the way. I definitely need an LSD as WOT in first gear is almost impossible to do unless the road are dry, my tires (crappy 800 wear) are warm and I'm going straight...
It breaks that easily, eh?
tmontagueThread starterCaledonia Ont. · Apr 3, 2017#43it does on my crappy 800 treadwear all seasons. The tread last forever but on anything wet or when they aren't warmed up the right tire will slip.
I can still do a 0-60 under WOT without any right tire slip, but on bumpy Hamilton roads under a slight turn when leaving a parking lot, no chance.
With better tires it should mostly go away, and of course an LSD would make a huge difference
ern-dizCA all day · Apr 3, 2017#44Right, makes sense.
thebarberGrand Rapids, MI · Apr 4, 2017#45needs moar tire
ArmstrongRacingSan Diego · Apr 6, 2017#46I was spinning 225/45ZR15 Hankook RS3's with the open diff....the 2zr is a tire killer. Now that I have an LSD, Ive been running 205/50ZR15 Hankook Rcomps....and I still spin like crazy at the start line.
tmontagueThread starterCaledonia Ont. · Apr 19, 2017#47Another update, finally installed my NST crank pulley. The revs seems to drop a bit quicker and the car seems slightly peppier but tbh it is not a mod I would be spending money on right away, better spent on other mods first.
The pulley is labeled for the Corolla S which uses the 2zr fae motor, but it will fit the 2zr fe no problem. However, it was labeled a normal size pulley and it is slightly undersized. not a big deal and I have no idea if the 2zr fae oem pulley is smaller than the 2zr fe but I think that is very unlikely and NST just CNC'd the wrong pulley for me. It's minimally smaller so I'm not concerned.
Now that summer gas is here my mileage is now about 6.5-6.9l/100km as opposed to 5.8-6.2L/100km. A little less miles per gallon but many more smiles per gallon 😁
I had a brief issue driving in salty slush in a spring storm that Niagara Falls NY had when I was travelling to the border for some car parts. I got 2 engine codes, one for my secondary O2 sensor and another for a faulty ECU. The O2 sensor was stuck at 1.275 volts but otherwise ran fine. It was due to me not using rubber plugs to fill the 3 holes from the immo wires I removed when i did the install to by pass my immo.
I pulled 3 rubber grommets from my 1nz harness and plugged the holes, luckily my ECU dried out and haven't had the issue since. Thanks Cranky for the heads up on the ECU hole issue 👍
I've recently ordered a MonkeyWrench Racing steel lightweight flywheel (8.8lbs) and will be installing that in a couple weeks as well as my poly filled engine mounts. This should make 1st through 3rd gear really snappy and take out some of the lag/slop in a stock engine.
I also ordered an RPM long tube header and will be having a new mid pipe made with my current resonator, single cat and aftermarket muffler because I love how ,my car sounds and don't want to part with that. The current midpipe hits my axle and rear right shock and has a slight rattle to it when the rpm's come down so I figured I'd get the shop to bend me some new pipe and fix that issue. I'll be splicing in some extra wire to extend the secondary O2 sensor to fit where the cat will now be placed. I won't have the header for a few weeks as they still have to make one up.
If you are doing the swap and plan on keeping your Yaris a/c lines, that is fine but take note that you will have to bend them slightly for them to clear any rubbing and to have the compressor side fitting on the low pressure hose fit better. I didn't bend mine and my hose was rubbing on the compressor. The other issue I had was that the bolt that came with my reman'd compressor is too short and only ends up grabbing a few threads onto the compressor. I didn't bend my yaris lines so there is a lot of torque on the fitting that goes into the compressor. This over time caused the bolts to ruin a few threads on the bolt and pop off.
When I was doing work today I lightly moved the line and it burst off sending UV dye and r134a all over my engine bay and just missed my eyes. This stuff is ridiculously cold so learn from my mistakes before you go blind.
I rebent the line in my bench vice (takes a lot of force to do) I made sure not to pinch any of the steel lines, so only bend as much as you need to. I then found a longer bolt in my parts bin and secure the compressor side of the fitting first, then the top side. I pulled a vacuum on the system and it held for 20 mins so i then ran my vacuum pump on it for 90 mins. I then sealed it all up.
I'm unfortunately out of my r134a so I'll have to wait until next week when i can go to the border and pick up some more. I'll be adding some UV dye as well since all the stuff I added before blew out.
We cannot get r134a here in Canada without a license and the r22 stuff they sell at CT for way too much money is flammable and not oem so I'd rather do it right and have it cost me less money. Hence why I'm buying some r134a from across the pond.
So far I've had no oil loss in 6k km except for the amount my oil catch cans are collecting which is more than I thought.
Another thing to keep in mind for those doing the swap in the future. I'd recommend sourcing all XD mounts and brackets if you plan on running the long tube header.
It is true that with the sedan swap you can use the yaris dogbone (torque mount) mount and bracket and it will be fine. Armstrong's mount sits perfectly straight and mine is slightly crooked but nothing to worry about or cause excess wear.
However, the xd mount pushed the engine forward an inch or so and gives extra clearance for the longtube header to fit. Armstrong has his header hit his firewall every so often under very hard shifting at high rpm's - and that was with a solid poly torque mount. Not a huge issue but another member with a hatch who ran all xd mounts and a long tube header never had any issue with the header hitting the fire wall. So for a DD if you don't want to experience the header hitting the firewall I'd recommend running all xd mounts and brackets and filling your torque mount with poly to make it a solid mount which limits how much the engine twists under heavy load.
Keep in mind with the xd torque mount you'll have to run xd shift cables and the 1-2 extra inches that the engine moves forward will be too far for your yaris cables to fit. The cables are stupid expensive and can't be found online so this becomes a pricier option then you'd expect.
That's about it for updates, I'll post back once I have my flywheels installed
thebarberGrand Rapids, MI · Apr 20, 2017#480.5-1.0L/100km is worth 30% more power while still using 87 octane
ilikericesavannah, ga · Apr 21, 2017#49 Originally Posted by
ArmstrongRacing ↑ I was spinning 225/45ZR15 Hankook RS3's with the open diff....the 2zr is a tire killer. Now that I have an LSD, Ive been running 205/50ZR15 Hankook Rcomps....and I still spin like crazy at the start line.
Your in Prepared class now.. just get some 15x9" wheels and slap some 255 Rcomps on now.. 😆
tmontagueThread starterCaledonia Ont. · May 4, 2017#50Short version:
2zr swap in a sedan needs the following mounts/brackets:
with long tube header:
- xd passenger side engine mount and bracket
-XD dogbone mount, Yaris dogbone bracket
- yaris trans mount and bracket
-XD shift cables (because of the xd dogbone mount which is longer than the yaris')
with stock header:
- xd passenger side engine mount and bracket
- Yaris dogbone mount and bracket
-Yaris trans mount and bracket
Here is a little update regarding the engine mounts and the sedan swap as I've had a slight issue this past week which I learned some more info from. To make this post easier to follow here is a break down of the mount situation. There are 3 engine mounts in total, these are the parts that contain the rubber dampener. There is the fluid filled engine mount (passenger side), dogbone mounts (aka torque mount) and the trans mount (drivers side). Each mount has a bracket which is the metal part that the mount affixes to.
Also to make this post make more sense it should be known that the 2zr is a wider engine (and slightly taller) so it takes up more space towards to the drivers side (left) crash bar. Or in other words, it causes the transmission to move closer to the left side
I initially did the swap with all of the XD mounts except for the dogbone and bracket as these were still the oem Yaris ones. This allowed me to use my Yaris shift cables (XD's are longer). The engine swap went fin and there were no issues what so ever.
Yaris dogbone and Yaris bracket
Picture not included in this copy
Now the Yaris dogbone is shorter by about 1-1.5" so the engine sits closer to the firewall. Because I recently ordered the RPM long tube header, I needed more clearance behind the engine to install it and to avoid any contact of the header on the firewall under hard downshifts. To get that extra space behind the engine, I installed the xd dogbone mount. This pushed the engine forward but the dogbone ended up being on an angle. This is not a serious issue but over time it could cause the mount to wear quicker and since I drive hard, I'd rather it be lined up straight.
To fix that issue I installed the xd dogbone mount and bracket, the xd dogbone bracket shifts the mount attachment point over a half inch so that the dogbone mount is straight. I installed the bracket, the mount was now straight. The next day I started noticing a vibration at the wheel under hard right turns. i thought it was from the rear wheels and thought it was the wheel bearings. But new bearings didn't fix the issue, and it turns out it was a vibration from the left (drivers side) cv axle and the trans.
Because the dogbone mount was straight the engine was now sitting more to the left (drivers side) where it normally settles. With the dogbone bent, it was sort of holding the engine/trans more to the right. The engine being more to the left ended up causing the left CV axle to now be fully compressed. The inner joint allows for in and out (length) movement which is needed due to suspension travel as well as making the axle easier to remove and re install. The outter joint does not have any in or out. This meant that the axle was at it maximal compression so when the left axle was rotated it would push the trans/engine over a quarter inch back and fourth.
This could be seen when the car was raised and no weight was on the suspension as the trans/engine would wiggle when you manually spun the left wheel. If the car was put in gear while raised the engine/trans would bang and vibrate. When driving and the suspension compressed there would be no issues. But under hard right cornering, the left wheel would be forced in due to driving forces and this would compress the axle more, leading to my vibration issue.
Putting the Yaris dogbone bracket back in solved the vibration issue, but the engine/trans still rocked slightly when the left axle spun and the suspension was unweighted. Also the dogbone mount was still on a sharp angle.
Xd dogbone mount and Yaris dogbone bracket with xd trans mount and bracket:
Picture not included in this copy
I decided to reinstall my Yaris trans mount back into the car to force the engine more to the right. I kept the xd trans bracket installed as it lets the trans sit lower in the engine bay to help keep the center of gravity down. Installing the Yaris trans mount is tough and requires a lot of muscle and a BF pry bar that you leverage against the crash bar and the outter trans case. This is so the engine/trans move enough to the right that you can get the bolt to line up through the dampener. After fighting it for 20 mins I finally got it installed.
Yaris trans mount, XD trans bracket, Yaris dogbone bracket, XD dogbone mount: You can see that the xd dogbone mount is almost straight now. If I installed the xd dogbone mount instead of the Yaris one (seen in the picture) the mount would be perfectly straight.
Picture not included in this copy
Here is how much room is between the trans and the crash bar with the Yaris trans mount, xd trans bracket, Yaris (I have polyurethane in the mount making it a solid bushing):
Picture not included in this copy
Here is how it was with the XD trans mount and bracket, Yaris dogbone bracket and xd dogbone mount:
Picture not included in this copy
Now the enigne/trans does not move when the left wheel is spun and the car is raised off the ground. Under hard cornering there is no issues and I can now feel some slight play in the left cv axle when installed on the car (this is a good thing as it means it's not binding or fully compressed).
For some unknown reason, the sedan seems to have less width in the engine bay, or the mounting locations seems to be closer together than in the LB. The 2zr swaps in the LB's seems to have no issues with axle compression regardless of what mounts are installed.