Yarisworld Archive

T Montague's 2zr swap - '08 m/t sedan some extra info

283 posts · 200,320 views · page 3 of 6

Replies continued

tmontagueThread starterCaledonia Ont. · Jul 4, 2018#101
Finally got around to pulling the video. All other tack footage was overwritten, the dash cam was awesome enough to save the crash due to detecting g forces. Glad to know that that feature works.

The crash doesn't look too bad as they typically don't. The ditch is about a foot deep and then there is a grassy field, the impact on the ditch was the issue which led to the wheel bearings going. I hit the ditch at about 125-130 km/h. The car stayed even during the turn due to its good balancing and me controlling the car but due to the speed I ran out of room on the track.

In the future I'll save and upload some track footage of some fast laps

https://youtu.be/35QL-BB3k3E
tmontagueThread starterCaledonia Ont. · Jul 14, 2018#102
Here is the link to 1 or 2 laps yesterday at TMP. I wasn't driving 10/10ths like last session. The off course crash last time shook me up a bit since I have a family at home. I ran 8-9/10ths mostly and just focused on looking where I wanted to go rather than where I am. I also braked a bit earlier than last time as I wasn't in the mood to push it to the limit.

https://youtu.be/gBvKvykTxtU

I ended up doing a couple laps on my street tires which are 340 tw BFG G-force sport comp 2's. I only did 4 laps or so as \i didn't want to wear them out but I wanted to test them at their limits. I ended up being only 3 seconds slower then my other laps that day and I wasn't even pushing them very hard. It is amazing how much better the turn in was and they actually give you feedback on what the car is doing. Needless to say mr R1's are heat cycled out and aren't really much faster than a street tire.

This now makes a lot of sense as I'm following cars on less sticky tires that are able to corner faster than me and I felt that I am no longer able to hold speeds in corners I used to be despite being a better smoother driver now than before. The car also felt very unstable on high speed corners almost as if the rear would swing out at any moment with no warning. This is a known problem with the R1's but it's worse now than ever before.

I'll use them the rest of the season and save up to buy some new rubber for next season. I'll just focus on my driving skill for now so that next season I should have no problem doing a sub 1:30 with new rubber. I always felt like the tires should hold higher speeds on some of the corners so this is starting to make a lot of sense now.

I also desperately need a racing seat for next season, due to my faster cornering I am using my left leg to hold myself in my seat by forcing it against the door. This is making me lose focus on driving and leading to a chaffed and sore left leg!

I am now able to take certain corners without having to brake whereas before I would brake to scrub off speed. I am definitely improving but like I mentioned, the tires seems to now really be falling off quickly and are now holding me back.

The ambient temps yesterday evening were around 34 C and I recorded the hottest ever coolant and oil temps at 222 and 280 respectively. The dropped down a bit once the sun dropped down but those numbers were at their peak on one of the hottest sessions.

Oil pressures read fine at around 60 psi so it wasn't a concern, but interesting to see how high they got. I'll run a UOA on the oil once it gets to the end of its life.
Ronnie VBrampton · Jul 15, 2018#103
This thread is a fun read Trev. Well done on all accounts. :) Even the "crash"......without the occasional trip past our limits it is tough to stay interested in track daying IMO.

On the subject of lap times I was chatting with another Echo HB owner last weekend at the autocross as the Hershey Center. He says his PB at TMP in a Stock drivetrain Echo is a 1.27.xx This was unreal to me.......I never timed my Echo last year without the SC but 1.27 sounds off the hook fast.........Daniel is no doubt a very good driver. His car has some decent suspension and weighs in at about 2100lbs with him in it.

So this has prompted me to get my lapcounter up and running. I obviously want to be a fair bit quicker than a 1.27..........watching your 1.30ish laps this seems unlikely but I guess I should have a goal. ;)

I'll be out with my friends on Friday June 27th for the evening session.......weather permitting.

All the best,
Ron
tmontagueThread starterCaledonia Ont. · Jul 15, 2018#104
1:27 seems insane on a stock drive train Echo. I won't say impossible as I've sen some excellent drivers run ridiculously fast times in bone stock Miata's, but a 1:27 is something I'd want to witness before I fully believe it. I have been recommended harry's lap timer and it was definitely worth the $10 one time fee to get it on my phone. Definitely get your lap timer out and see where you're at.

Based on how much more stable and confident my car felt on my street tires made me really realize how far gone my slicks are. I would be happy with lap times below 1:30 but I think a 1:27 would be possible on my car with proper tires. I'll know for sure next season when I'm on new rubber but for now I'll have to see what I can do with the tires I have.

As a side note, what are people running for brake pads? I think I have found the limits of these Hawk HPS now that I am braking much later as they no longer have much bite to them and they glaze my rotors like crazy. They will still stop the car without fading but they have little initial bite which isn't very confidence inspiring

I'll book the 27th session and hope to meet you out there again. It's more fun seeing familiar faces out there and last Friday it was a sh*t show with how busy it was and how many overseas young kids there were in their +$150k cars parking anywhere and blocking people in...one of the reasons I wasn't in the mood to push it too hard.
RunethecursedSocal · Jul 15, 2018#105
I am using EBC yellow stuff. alot more dust, alot more noise. they are hard as bricks cold. but heat cycled they stop good every time and our cars dont really push them to overheat.
Ronnie VBrampton · Jul 20, 2018#106
On the subject of brake pads I just got a set of Hawk Blues. Everything I have read says do not use them on the street as they will wear out rotors very very quickly........

Given how easy it is to swap brake pads on my car I am just going to put them in for track days.......the trip there and back shouldn't do too much damage and rotors are cheap anyways.

I bet they stop the car on a dime.......we will see on the 27th.
tmontagueThread starterCaledonia Ont. · Jul 20, 2018#107
Too bad they cannot be found online anywhere for mkII cars. I'll definitely need to find a track specific pad for next year
tmontagueThread starterCaledonia Ont. · Jul 28, 2018#108
Was out at TMP last night and had my confidence back. Due to some hot temps a few weeks ago I decided to modify my hood a little, function>form, not the prettiest but better than I thought for a rushed job

Picture not included in this copy

Ambient temps were a bit cooler last night than the session before but all in all it seems that the coolant temps were down 5-10 degrees and oil temps didn't go above 260. It seems to have worked bu relieving some of the high pressure behind the radiator which restricts the airflow going in during high speed.


My old Hawk HPS pads were getting low after 700 or so track km's on them and a bunch of DDing so I lightly resurfaces the rotors which were all glazed and threw on a new set of HPS'

Picture not included in this copy

Picture not included in this copy

Needless to say it is very apparent that these pads are not up to gear with my now improved driving. I never lost brake power completely but the stopping power would be stupid inconsistent where I would hit turn 2 and the pads barely seemed to grab and scrub off speed. I will be ordering some Carbotech XP10's and a flex hone to proper resurface both sets of rotors I have. I will then run the xp10's with their own set of rotors and keep the HPS' for DDing and winter driving. It will be a bit of a pain to have to swap each time but the HPS' are downright dangerous if I'm pushing it at the track.

I also learned of how bad my tires really are, they cannot be pushed to the limit as they just let go and are very unstable. Their limit seems to be that of a 400 tw tire, this obviously does not make you feel confident heading into a high speed corner. I was running 1:34's about 4 seconds slower than my fastest lap 3 sessions ago. This was also due to the brakes but my traction is steadily dwindling. I am a much better driver now than when I started this year and I know my lines are much better than previous. I am confident with new tires, and proper brakes I can run a 1:27-1:28 but the budget is being used for brakes and a race seat for now so tires will have to wait until next year.

I also need to strip some weight off of the car but the problem is it is my DDer and I need the back seat in it for my baby seat. I'm really starting to see the benefit of having another DDer. Ron's first gen is just over 2000lbs where as mine is about 2375lbs and on the straights it is slightly apparent. I am also going to try and find someone to build me a long tube header over the winter which should help for about 10-15 whp give or take.

Brake pads are on order as there is no way I am going back to the track with the HPS pads
tmontagueThread starterCaledonia Ont. · Aug 18, 2018#109
After my last track session with Ron I had a new found motivation to stick with the Yaris chassis for the near future. He was posting a 1:26 in his first gen which is good enough to beat the typical "track day bro" in an STI or BRZ at TMP - our local track. My plan wasn't to beat a certain car, its always been to become as fast as a driver as I can while having fun and testing new things I modify or add to the car to make it faster. That said, being competitive at track days with cars that cost way more or people assume to be faster keeps the sessions fun and exciting. It also never gets old to pass STI's, WRX's, BRZ/FRS's etc while they look on with a dropped jaw at the Yaris going by.

I also refuse to do another track day with my Hawk HPS's - the brake fade is real and hitting corner 2 where the brakes sometimes do nothing and sometimes work half as good as they should is just stupid dangerous. I already ordered and picked up some Carbotech XP10's and I resurfaced both sets of my rotors with a rotor resurfacing tool that you install on a drill - not as good as a proper machine but worked good enough for what I need it for. I will daily in my HPS's and swap out rotors and pads the night before going to the track. I also picked up an older Sparco Sprint seat (first gen?) from Ron and am currently waiting on my seat base before I can install it in my car.

This will help me get back to my 1:30 time hopefully but on my current past worn tires I'm not holding my breath. Next season I'll have some new 100 tw rubber and I'll be aiming for a 1:27. If I'm fortunate enough to have a long tube header on my car by then, then even better as the extra 10-15whp definitely won't hurt.

The biggest limitation right now is the fact that this car is my daily and houses 1 (soon to be 2) car seats. I have a few extra hundred pounds sitting in my car waiting to be stripped out. It's looking like my family and I will be moving to a larger house a year or so from now and our next place will for sure have a garage. This will allow me to pick up a beater Yaris LB A/T. I can then keep my sedan in track mode and not have to swap out brake pads and what not every couple weeks. I can then strip it out and lose a bunch of weight in it.

Over a couple years I'd like to do a diy splitter as well as cams and a standalone ecu. I think the 2zr can realistically and conservatively achieve 150whp on pump gas and retain its reliability. This would make a pretty fast sleeper and should be able to post up consistent 1:25's at TMP.

I'll be back at the track on the 7th of September and hopefully I'll have the Sparco seat installed by then. I'll post back with how I find the brake pads.
atomic_hojiKincardine, ON, Canada · Aug 19, 2018#110
Originally Posted by tmontague ↑
...
The biggest limitation right now is the fact that this car is my daily and houses 1 (soon to be 2) car seats.
...
Whoa, whoa.. just sneak that in 'eh?! 😲 New bun in the oven? Congrats, man. 👍

Glad to hear you're going to keep the Yaris for a bit longer. Looking forward to see what you find for upgrades for the 2ZR - Monkey Wrench Racing has goodies, but the more wild you want to go the less there seems to be for support; at least so far as I've found from the 'armchair upgrade seat', lol.

Enjoying following the progression of the car over the past while, you've been doing an awesome job with it. Makes a good go-to for motivation.. 👍

-- Adam
ern-dizCA all day · Aug 20, 2018#111
Originally Posted by atomic_hoji ↑
Whoa, whoa.. just sneak that in 'eh?! 😲 New bun in the oven? Congrats, man. 👍

Glad to hear you're going to keep the Yaris for a bit longer. Looking forward to see what you find for upgrades for the 2ZR - Monkey Wrench Racing has goodies, but the more wild you want to go the less there seems to be for support; at least so far as I've found from the 'armchair upgrade seat', lol.

Enjoying following the progression of the car over the past while, you've been doing an awesome job with it. Makes a good go-to for motivation.. 👍

-- Adam
+1000
tmontagueThread starterCaledonia Ont. · Aug 20, 2018#112
thanks guys, it's definitely an exciting time for us and so far I've been having a blast teaching my 21 month old how to wrench cars and do reno's on a house. Currently his favorite activity is going through my tool box and giving me every screwdriver I possibly own. The next one is a girl so it will be fun to see them interact with one another.

MWR has a fair amount of 2zr fun bits that I would like to use but it seems to make sense to pair it up with a standalone ecu or else the gains would be negligible (ie: cams). I have always wanted to build a motor up and the parts that MWR have would make that pretty fun. Knife edged crankshaft, stiffer valve springs to raise the rev limiter up. I am confident that with a build like that with a heightened rev limiter the 2zr could be capable of fairly easily getting >150 whp on pump gas.

The budget limits this for now but it would be a great way to build an engine and learn my way around that.

I forgot to mention in my above update that I swapped out the Cusco trans fluid for some Amsoil MTG. The Cusco had some track days on it and with clutch plates the fluid suspends the wear bits so you don't want to run it too long. I didn't go with the Cusco due to the cost of it and I have ran the Amsoil before and was happy with the price and performance. My LSD was chattering like crazy so I went out and bought some CRC lsd fiction modifier and slowly added in a couple quarts at a time. I finally found the sweet spot at around 4.5-5 ounces. keep in mind I over fill my trans a bit and I have around 300-400mls extra in there (fill it while the front is jacked up).

Amsoil also has a friction modifier but I couldn't easily obtain it and I didn't want to wait for shipping so I went with what I could fine around here. It is now fairly quiet how it originally was but still locks as it should.
fujiwaruOahu,Hawaii · Aug 22, 2018#113
Originally Posted by tmontague ↑
After my last track session with Ron I had a new found motivation to stick with the Yaris chassis for the near future. He was posting a 1:26 in his first gen which is good enough to beat the typical "track day bro" in an STI or BRZ at TMP - our local track. My plan wasn't to beat a certain car, its always been to become as fast as a driver as I can while having fun and testing new things I modify or add to the car to make it faster. That said, being competitive at track days with cars that cost way more or people assume to be faster keeps the sessions fun and exciting. It also never gets old to pass STI's, WRX's, BRZ/FRS's etc while they look on with a dropped jaw at the Yaris going by.
I feel the same way, but more along the lines of trying to catch up to the autox times all the other cars are posting while I try to improve my yaris/driver skills along the way.
RunethecursedSocal · Aug 22, 2018#114
You can do it, to both things. even under stock powered 1nz's the car will teach you how to momentum drive, and its rather easy to work on and with.
tmontagueThread starterCaledonia Ont. · Sep 8, 2018#115
Headed out to TMP last night and unfortunately my seat bracket had not come in yet (should be here Monday) so I was stuck using oem seats and flying around the cabin. I was able to get used to my track pads (Carbotech xp10's) for the first time and all I can say is wow. I swapped out rotors and pads the morning of and bedded them in before I left for the track - I have a dedicated set of rotors for these pads.

It's a different animal when you have track pads than street pads and it is much safer. I likely still have a second to shave off each lap just in braking but I need to build up the balls to get to that point. It's amazing how late I can brake now and how much speed scrubs off in such a short amount of time. It would fully kick in the abs after the straightaways and I'd have to manage the car from wiggling when the tires locked up.

I did about 140km's yesterday with 4 session of about 40 minutes and I never once experienced brake fade. They were always consistent and the pads didn't wear down much at all. I ended up going through 3/4 of a tank of gas which was more than usual so that says a lot for how much driving I did. I also broke the weld on my muffler and it ended up melting my rear bumper. I removed the muffler for now and the sound is awesome but much too loud to daily in.

My fastest lap was a 1:30:22 and the lap after that I was on par for 30secs faster with 1 corner to go but I caught traffic and had to slow down. I realistically would have cracked the 1:30's by a bit but after the 4th session I packed it in as I was starting to feel tired. Oddly enough this was one of the first track sessions where I was becoming faster each time out. Likely due to getting more and more comfortable with a track pads. The tires are still my largest limiter and I cannot corner nearly as fast as I should. It will be interesting next season how much time I will shave off with new rubber and faster cornering speeds.

I will be out again in 2 weeks as my wife's due date for baby #2 is coming up soon in about 4 weeks so once the baby is here it will be it for my track days this year. I will at least have one session to try out the Sparco seat, I was flying around everywhere in the tight twisty corner yesterday - especially during the few back to back corners where I now no longer hit the brakes.

I had another handful of people come up to me and ask about the car and how long I've been driving. There was a huge Subie group out in their WRX's that was really interested in the car which was pretty neat. A few of them thought my car was s/c and were surprised to hear it was an NA 2zr. In a sea of Mustangs and WRX's people apparently love seeing a Yaris rip around the corners at the limit. There is a large radius turn where people sit and watch behind a big concrete median and I noticed that many of the big V8 cars out there weren't pushing nearly as hard at the corner but instead relying on the big engines to pull them fast into the straight out of the corner. They typically cornered at about 60km/h. When I got more comfortable with the corner I was able to get up to about 78km/h with the tires screaming. People apparently loved watching that. I was also able to get the point by multiple times from a Celica GT-S (haven't seen one of those around here for years)

Like I said before, driving a slow car fast is much more rewarding than a fast car slow. I'm hoping to break the 1:30 next time out and then that will be it for me this year. Time to save up for a long tube header, new gauges and new 100tw tires.
06YarisRSFredericton, New Brunswick, Canada · Sep 9, 2018#116
Time for a dash cam. 👍
thebarberGrand Rapids, MI · Sep 9, 2018#117
Sweet
ern-dizCA all day · Sep 10, 2018#118
Surprised you didn't get any brake fade running the factory lines. Usually the fluid heats up and the lines start to give a little, no?
tmontagueThread starterCaledonia Ont. · Sep 10, 2018#119
Zero fade even after 40 minutes of hard laps. You should never experience fading with a proper pad as long as you are in the appropriate heat ranges. I experienced fade before due to using a street pad and getting the temps well above its range.

I currently have ss front brake lines but even with OEM lines no grade should be felt with proper pads. I bleed my brakes every 3 track events so the fluid is fresh and is a mild high performance dot 3 fluid but not an expensive race fluid.

As long as you don't boil brake fluid - which is hard to do in a light car if you keep the fluid fresh - you won't experience a loss in braking.

After using these pads in an now say that upgrading to larger brakes are pointless for performance in this car. As other have stated pads are all you need. I could lock up the tires (w/ abs kicking in) when I'd hit the brakes into a sharp corner after a long straightaway. Thus was on r compounds tires as well although they are heat cycled out
CrankyOldManWest Michigan · Sep 11, 2018#120
Originally Posted by tmontague ↑
In a sea of Mustangs and WRX's people apparently love seeing a Yaris rip around the corners at the limit. There is a large radius turn where people sit and watch behind a big concrete median and I noticed that many of the big V8 cars out there weren't pushing nearly as hard at the corner but instead relying on the big engines to pull them fast into the straight out of the corner. They typically cornered at about 60km/h. When I got more comfortable with the corner I was able to get up to about 78km/h with the tires screaming. People apparently loved watching that. I was also able to get the point by multiple times from a Celica GT-S (haven't seen one of those around here for years)

Like I said before, driving a slow car fast is much more rewarding than a fast car slow. I'm hoping to break the 1:30 next time out and then that will be it for me this year. Time to save up for a long tube header, new gauges and new 100tw tires.
So much this.

I was at Grattan speedway on Labor day for an almost-full-course autox. Came in 4th of 6 in HS with the Echo (behind a pair of Fiesta STs and a Civic DX) but beat a full sized sedan by a second and a half. He clearly had me on the straights, but I didn't have to lift in the sweepers. Momentum cars FtW!
ern-dizCA all day · Sep 11, 2018#121
👍
tmontagueThread starterCaledonia Ont. · Sep 22, 2018#122
Although this thread originally started as my 2zr build thread to help others who plan on this in the future - it has now become more of a thread about my musings in regards to tracking my daily driven and 2zr swapped car. My hope is that this helps anyone else down the road who has some questions regarding tracking there car and my posts guide them on making the best choices for their car. I was helped by many others in the past who posted about their experiences on the track so I'm hoping to do the same.

I headed out to TMP yesterday evening and got even more familiar with my new Carbotech xp10 pads. I was able to brake slightly later as felt more and more confident. I ended up finally breaking 1:30 and ended up with a fastest lap of 1:29:91. My goal at the start of the season was to break 1:30 so i'm happy with how it all went. I also realized that some of my major snap oversteer with the tires was actually too high of cold temps. I originally had it set up with 32f/29R and last night worked it down to 30.5/28 and noticed that the tires felt much more stable and the over steer limit was much improved. The frotn tires after the session were the cleanest I have ever seen and I'm finally getting some proper outside shoulder wear. The rears still need to drop a bit in pressure to have adequate wear.

This was the last session of the year for me as my wife is about a week or two away from popping out baby #2. I also plan on having new rubber on the car for next season. Leaning towards toyo r888r's which iirc are a 100tw tire. Ron had good things to say about them as have others I have spoken with. They seem to be very forgiving at their limit which is what my current R1's lack and I need a forgiving tire to improve pushing my limit as a driver.

Car ran excellent, no more coolant loss every since I switched back to the oem rad cap. It was a stupid hot day until the sun dropped and coolant peaked up to 234F. Notg an issue but still pretty high. I want to look into getting a dual core rad down the road but there are no bolt in options that I'm aware of for a 2nd gen yaris 🙁 I'll probably have to wait until this becomes a track only car and I do an a/c delete then I'll have to have a universal one put in with the help of a fab shop.

Oil pressure stayed around 45psi give or take when the rpm's were close to redline. I'm currently running Pennzoil ultra platinum 5w30 (oem spec is 0w20) and when this car is only track driven the plan is to go to pennzoil UP 5w40. My winter oil is a mobil 1 0w30 and it works fine. I will be doing a full UOA on this oil when I drain it before the winter. I am current at 13,500km and about 700-900 km's of that is heavy track use. I use toyota oem filters changed at 8k km's. I am interested to see how well the oil held up and will post my results.

Currently my glowshift oil temp gauge has a broken wire and it's pinged at full hot. I plan on running AEM digital gauges on the A oillar for next season. Glowshift did the trick but are cheap, noisey, not all that accurate and the wiring makes for a headache compared to the loom that come with the AEM gauges.

This was the first time I got to experience a racing seat at the track. Huge difference and definitely a worthy upgrade albeit not a cheap one when you factor in seat brackets/rails. I am now sitting lower and the steering wheel is a bit too far away from my ideal driving position (which I'll address later with an aftermarket wheel) but damn I wasn't thrown around one bit. During the tight 3 back to back moderate speed corners where I would be bucked around like crazy before, I never once had to worry about my left foot placement to brace myself. I was able to bit all of my concern and energy into driving which made a huge difference.

highlight of last night was having a c7 z06 come up behind me on the first straight away before turn 1. I was going to do my cool down lap but when I saw him behind me I figure why not go for another hot lap and see how long I can hold him of. The tires were sticky and I was feeling good. He just caught me before turn one and I braked late and hit the turn a bit more ballsy then normal. I realized I gapped him a bit and then he caught me before turn 2. I gapped him a bit after taking turn 2 at ther absolute limit of the tires (aprox 95km/h) then headed into the back to back tight moderate speeds turns. With no straightaways to catch me I gapped him some more and by the time I was at the last corner onto the last straightaway he was at least 4 seconds behind me. Turned out this was my PB lap! Although this clearly wasn't a very good driver, he wasn't being shy on the corners and was pushing pretty hard.

The main issue I've come across tracking a yaris is that people don't give you the point by because they think you are slow since it's a Yaris, even when you are on their ass the whole lap. I had a miata infront of me (not a great driver) that I clearly was much faster than and was on his ass and in all 4 passing zones he never pointed me by. Technically you are not supposed to pass unless signalled but he blew a corner too wide so I took the inside on him. Later in the paddocks when I was chatting to him he said "Man you are fast with that thing, I couldn't believe it when I looked in my rear view mirror and saw a Yaris, I was like no way it's faster than me" 🙄

I used to use permatex regular synthetic brake grease and noticed after each track session is became very dry and heavy and had to be replaced. I looked at the specs and it's only good to around 500F. As a side I also used the red stuff Hawk sends with their pads - it is only good for greasing up the metal contacts on the pad backing plate. Do not use it on sliders it is much too thick and gums up after a track session. I decided to go with the expensive purple permatex synthetic ceramic grease. After yesterdays 140km worth of 5 session the grease was still as smooth as when I applied it. No issues what so ever and I highly recommend this brake grease to anyone who tracks their car - well worth the money.

When putting my street pads back on the car today I noticed that my passenger side endlink that came with my BC coil overs is toast. The top joint is loose to the point you can wiggle it and make it clunk with your hand. These are less than 5 months old. I will be contacting BC for warranty issue but I'm not sure if they count this as a wear item. I went online and noticed that they only charge $17.50 CAD for new ones! that is stupid cheap and i'm happy to see that as I can pick up a few to have on hand as needed.

I also found out that my drivers side CV axle (the aftermarket shorter Tercel one) I installed early this year has a fair amount of play in the inner joint. My original oem passenger side one is still rock solid. The drivers side axle has a 1 years warranty so I'll be getting a replacement for that. Aftermarket axles are cheap in price but also cheap in quality. I'll see how many more aftermarket ones I have to go through but I may have to see if I can get that axle in an OEM reman'd version. There are companies that make them and offer lifetime warranty and they tend to be about half the price of oem ones.

The plan for the this winter as I save up some cash to make my car faster is to buy/find a long tube header, aem gauges, aftermarket steering wheel with a 3" dish to bring it closer to me with my new seat, extra xp10 brake pads as well as some proper higher performance rear pads and 100tw semi slick tires.

I'll also be trying out some goodrich brake lines as the current stoptech SS ones I have are bent very sharply due to the length/design and they are cracked in so a lot fo different places. They still function fine but I don't trust them past about a year of hard use.

This is all for now, next year I'll be looking to make a new PB of a sub 1:27, we will see how that goes.
RunethecursedSocal · Sep 23, 2018#123
Originally Posted by tmontague ↑
" I was like no way it's faster than me" 🙄
I got that alot in STS racing the car down here.

they where like "and how much power does it have?" the only guys I couldnt stab is a fully prepped EF hatchback and the driver and his co-driver which also have years more experience than I have. oh and my roomate who has the balls to the walls approach with his mazda 2
ArmstrongRacingSan Diego · Nov 7, 2018#124
#5
tmontagueThread starterCaledonia Ont. · Nov 12, 2018#125
I've been a little MIA lately, my daughter is now 5 weeks old and my son almost 2. Needless to say my focus has been on my family and doing as much as possible with them. My son however is obsessed with my "race car" and loves helping me wrench when ever he can. Our latest project was installing new headlights. He banged a wrench around the bumper, kept looking under the car and handing me new tools - it was a great time.

I ended up getting rid of my HID projectors. The lenses were in need of serious work as the Clear protectant I used started to crack off after a few years. I was tired of having issues and having to troubleshoot them (latest one was one of the halo's flickering and not working - issue with inner soldering work when they were manufactured). I also hated having an engine bay full of wires.

The light output was great in the city but sub par on rural roads and high beams were useless. I liked the style points they gave, but they looked weathered. It would have taken a lot of effort to sand them all down again and I didn't want the trouble of having to open them back up again and then re seal only to fix the halo drl. I don't like how the oem headlights look on a dark car with them being silver. This was one of the main reasons for doing the retrofit, I painted the shrouds black so they matched better with the body color of the car.

However, I found oem type headlights on ebay (and Amazon) for $100 USD shipped freeto my US PO box that had a black shroud. The only silver parts was the reflectors for the main headlights. For that price and their good looks there was no way I was passing that up. The headlights fit perfectly and they look awesome. I opted for some Silvannia extra vision headlight bulbs as they seem to be the best balance of cost, longevity and performance. I'm not a fan of the blue tinted lights as they reduce lumens and leads to the need to overdrive the filament to create the same amount of light. I am beyond pleased with these as they fit excellent and make the car look much better overall with their brand new lenses. I ceramic coated them and will do so often so they should last a while. I now have a clean engine bay except for the one relay I have for my dual horn set up.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

I recently installed some AEM x series gauges (oil temp and pressure) and have a 3rd pod on my a pillar for an AFR sensor down the road. I used an a pillar pod from ebay that apparently fits a yaris. It does not and even if it did there is no way to mount it to the a pillar. I just trimmed up and used self tapping screws to screw it into the facotry a pillar. Looks clean and works well.

I am impressed with the gauges, much better build quality then glowshift. They are prices somewhat reasonably considering the quality you get. They works well and the install is fairly simple, at least compared to the glowshift garbage I had. I did have one issue with them as the oil temps sensor connectors are not snug like the pressure sensors are. If I wiggle the sensor I can get the gauge to read "sens" which means the connection is disrupted. There should be no play int he connectors. I have been emailing AEM and they sent me a new harness to try. I will be swapping that connector and seeing if it fixes the issue. The issue could be the sensor side connector so I have to try this first.

The harness they sent me have a completely uncrimped ground wire pin. Not very impressed. That said, AEM has been in constant communication with me and has always responded quickly and was very apologetic. They didn;t make me uninstall the gauge and resend it all back like they originally wanted me to after I told them how much extra cost and time that would be to me. I have temporarily shimmed the sensor snug with a thin piece of plastic and it has been working perfectly. This will work until I get under the car again to test the new connector.

All in all I would buy future AEM products as their communication has been top notch.

I am currently waiting for my new steering wheel and quick release to arrive. It's a 3" deep dish wheel so it should fix my seat position issue I am currently having with my race seat and oem wheel. I'll post a brief review about that once I've installed it.

I will be ordering some Nankang AR-1's or Toyo r888r's for next season as well as upgrading my rear brake pads to something that can handle track temps. Other than that, the only other thing I'm hoping to get done for next year is have a custom long tube header built. Due to RPM no longer making their long tube header for a really good price, I'l be stuck having a local fabrication shop do the work for boatloads more then it would have cost for rpm's unit.

I'm hoping to have the cash this winter to have it done for next season, but this is the one thing that may have to wait until the season after. It would really complete the factory tuned engine and get me close to 150 whp. We'll see if it happens but I'm crossing my fingers.

I also plan on stripping out some of the car this summer. I won't be removing the a/c or any seats until i have another daily driver, but I'll be removing some panels in the rear, potentially the speakers and what ever else I think would be helpful. I'll be picking Tom's brain on this one. Oh, and lastly I am hoping to have a battery reloaction done over the winter. It isn't too expensive and would make for a fun project. It will help with the balance of the car but it will also free up some space in the engine bay every time I pressure bleed my brake or need to access the transmission mount.
ArmstrongRacingSan Diego · Nov 13, 2018#126
Awesome looking car man, I'm really jealous you get to daily drive it.

Speaking of daily driving, since you have the 4.3FD you can buy just a taller 5th gear for better mpg/lower rpm. Email this guy and ask for the .725 5th gearset from a 03-09 Corolla; mmerlimm@teleport.com

When you are ready I can send you the tools, just return them when you're done.
stidnamAustralia · Nov 13, 2018#127
Didn't realise you were running hypergrams :) good looking wheel. Any side shots?

Any scrubbing with the 195/55 setup? Rolled guards?
06YarisRSFredericton, New Brunswick, Canada · Nov 13, 2018#128
Headlights look great! Would love to see pics of your gauges setup. I was thinking how nice it would be to have oil temp, pressure and trans temp, since I can't get that with on my head unit in Torque like in my van. I was looking at the compartment cover just behind my steering wheel in the Yaris. Would be the perfect place, although they'd be obscured when I turned the wheel.

I wonder if this would work?

https://www.ebay.com/itm/Fits-06-08-...YD0F:rk:1:pf:0

Picture not included in this copy
tmontagueThread starterCaledonia Ont. · Nov 13, 2018#129
Originally Posted by ArmstrongRacing ↑
Awesome looking car man, I'm really jealous you get to daily drive it.

Speaking of daily driving, since you have the 4.3FD you can buy just a taller 5th gear for better mpg/lower rpm. Email this guy and ask for the .725 5th gearset from a 03-09 Corolla; mmerlimm@teleport.com

When you are ready I can send you the tools, just return them when you're done.
Thanks man, I miss it on weekends since it normally sits in the driveway while we use the Vibe. It's a blast and even when i have another daily it will still be street legal thanks to no longer needing etests - I'll still be able to take it out for a rip when I feel like it.

Thanks for the info on the 5th gear. It will be needed for tracks like mosport when i start there soon. Is that the sake gear that we chatted about a while ago that was a matrix gear?

Originally Posted by stidnam ↑
Didn't realise you were running hypergrams :) good looking wheel. Any side shots?

Any scrubbing with the 195/55 setup? Rolled guards?
Thanks, I'm happy with them, they are 15x7.5 +35. I rolled my rear fenders for my track set up which are 205's and I have 10mm spacers on the rear. No rubbing iron issues, fronts are not rolled but I'm running -1.5 rear and -2.8 front camber which helps. It's a nice looking aggressive set up when looking head on at the car

Originally Posted by 06YarisRS ↑
Headlights look great! Would love to see pics of your gauges setup. I was thinking how nice it would be to have oil temp, pressure and trans temp, since I can't get that with on my head unit in Torque like in my van. I was looking at the compartment cover just behind my steering wheel in the Yaris. Would be the perfect place, although they'd be obscured when I turned the wheel.

I wonder if this would work?

https://www.ebay.com/itm/Fits-06-08-...YD0F:rk:1:pf:0

Picture not included in this copy
I'll take a pic as soon as my new wheel is installed (currently delayed due to postal strike)

That is the gauge pod I bought. I cut off the bottom and top part so it is essentially just a screw on piece with 3 pods
06YarisRSFredericton, New Brunswick, Canada · Nov 13, 2018#130
Originally Posted by tmontague ↑

I'll take a pic as soon as my new wheel is installed (currently delayed due to postal strike)

That is the gauge pod I bought. I cut off the bottom and top part so it is essentially just a screw on piece with 3 pods
The listing says that it fits both sedans and hatchbacks. How was the fit out of the box? It's looks close to the color of my RS interior trim. I have to institute a bit of a spending freeze after the swap, but I can see me having oil temp, oil pressure and trans temp in one of these pods!
tmontagueThread starterCaledonia Ont. · Nov 13, 2018#131
Fit is terrible, the bottom portion is way to big and wont fit and the top curve doesn't match up properly. There isn't any place to put the plastic push pins in it either so you couldn't use it to replace your oem cover even if it did fit
ArmstrongRacingSan Diego · Nov 13, 2018#132
. .(....Is that the sake gear that we chatted about a while ago that was a matrix gear?)


Yes that’s correct, it’s the tallest gear we can get for these transmissions. It’s the same ratio as my 6th.
06YarisRSFredericton, New Brunswick, Canada · Nov 15, 2018#133
Originally Posted by tmontague ↑
Fit is terrible, the bottom portion is way to big and wont fit and the top curve doesn't match up properly. There isn't any place to put the plastic push pins in it either so you couldn't use it to replace your oem cover even if it did fit
Well, that sucks! You wouldn't think it would be that hard to make a good-fitting one from an actual piece as a template. 🙁
tmontagueThread starterCaledonia Ont. · Nov 20, 2018#134
Here's a cockpit shot

Picture not included in this copy

I installed the steering wheel with functional horn today (no SRS light so pasenger airbag is fully functional). I took a ton of pics and plan on doing a full write up on how to properly wire a horn. There are no proper DIY guides online for this except a bunch of terrible instructional videos from a few highschool kids.

The steering wheel is now at a proper distance away from my chest and I no longer hit my legs with my hands when turning the steering wheel

Picture not included in this copy
ArmstrongRacingSan Diego · Nov 23, 2018#135
That looks awesome!
tmontagueThread starterCaledonia Ont. · Dec 15, 2018#136
Thanks to Adam I received my badge and installed it earlier today. I didn't install it on my front grill as I have a TRD badge there that I like and my '08 grill doesn't really have space for the TSport badge. I ended up taking a hacksaw to the rear mounting tabs and cutting them flush. I then used my bench top grinder and ground them flat and roughed up the back surface. Then installed 3M double sided automotive tape. I trimmed the tape and then installed th new badge.

I had to remove my old crappy knock off badge and wiped it with Goo Gone. Just make sure you wipe off the old Goo Gone with alcohol before you install the new badge or else it won't stick. The oem Tsport badge is much better quality and it is coated in a urethane so the badge won't get worn out or caught on a micro fiber towel like my old one did

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

The other day I got tired of not having anything to do on my car so I decided to strip out as much of the interior as I could while still keeping my one child's car seat in place. Below is as far as I was able to go and I even kept the dome light in place. I used some aluminum tape to hold down the wires and it worked well. I also re installed the passenger side "holy shit bar" since I have yet to install a passenger side race seat.

The radio was by far the heaviest thing I removed from the car, it must weigh at least 12-15lbs. I have to keep the HVAC and a/c as I can no longer roll down any windows except the driver side and I need the a/c for my kids in the summer for the odd time I pick them up from day care. I'll find out in ther spring how much weight I've stripped so far but I should be below 2300lbs now with an almost full tank.

Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy

I'll post later this weekend about my future plans with the care over the winter
06YarisRSFredericton, New Brunswick, Canada · Dec 15, 2018#137
It would be interesting to know what the total weight of removed materials is. Could you use a bathroom scale holding each piece and subtracting your weight, then total the differences? I'm going to guess that you have lightened the car by ~ 60 lbs. It may sound silly to the average car person to care about minor weight reductions, but for racing, that's a different story. Badge looks great!
Ronnie VBrampton · Dec 16, 2018#138
Nice seat! Like I mentioned, anytime you want to see total weight it's 20 minutes to roll it on my scales.

Corner weighting will take considerably longer. ;)
atomic_hojiKincardine, ON, Canada · Dec 16, 2018#139
And my wife calls my car the ghetto-mobile! 😲 lol

Jokes aside, the car is looking awesome man. 👍 You, Tom, Jason, ... there's a growing number proving "hardcore" and "Yaris" in the same sentence can be done, lol.

-- Adam
tmontagueThread starterCaledonia Ont. · Dec 18, 2018#140
I don't have a scale at home so it won't be possible for me to weigh what I have removed. That said, Ron has been kind enough to offer his corner balance scales to use so I'll be heading down his way soon to see where I'm at. I was around 2370lbs prior to this with an almost full tank of gas, and I think I removed around 60lbs.

Two big heavy items that I wish I could remove but cannot until I have another DD'er is the complete rear seat and heavy brackets as well as the a/c and hvac system. There is probably at least 50-70lbs in those alone.

As I stated in a few posts earlier my family will be looking to upsize our house after next winter which means a garage and a driveway that can fit a minivan (yup, I'm becoming cool soon). This means in over a year I'll use my wife's current car ('05 awd pontaic vibe). The plan is to strip out the rest of the Yaris as well as the inner door skins and replace the glass with lexan or polycarbonate. I'm hoping to get the weight below 2000lbs. The passenger seat will be replaced with a proper race seat as well.

For this winter the plan was to use my tax return money for a custom fabricated long tube header. However, this will cost over $1500 as I also need the rest of my exhaust reworked as it is rattling and banging my rear suspension. The more I thought about it the less it made sense. I've had my mind set on the long tube header for a long time because it used to be sold for a great affordable price (~$375). However I failed to realise that for the price it would now cost me there seem to be much better ways to spend that money and go fast. We no longer need e tests in Ontario so stand alone ecu's are now an option for a street legal car and I think that this would be a great bang for the buck mod. I don't want to run a tune until I have another DDer just in cased things go south.

The plan is to focus on weight and reliability to get me ready for a future built engine. The long term plan for this car is to use available bolt on options and make this car a competitive track car that competes in grassroots time attack series. Monkey Wrench Racing sells a lot of 2zr engine components that would make a seriously fast engine. With stage 2 cams, upgraded valve springs and 12:1 compression pistons I'm confident this engine could make between 150 and 180 whp on pump gas with an 8k red line. That is the long term goal.

For the winter I'll be relocating the battery to behind the passenger seat. The benefit of this is not only better weight distribution, but much less clutter in the engine bay every time I bleed my brakes and/or need to remove the trans. I can now disconnect the battery with a flip of the breaker.

I'll be installing a 1st gen dual row radiator and converting the other necessary parts to make that work to fix my high coolant temp issue. And as always planned I'll be picking up another set of carbotech xp10 front pads and a set of Nankang AR-1 tires. If there is any cash left over after that it will go to getting my exhaust rebuilt and potentially a DC sports header although I'm not convinced it is worth the cash yet. I'll update the thread as I slowly install each part.

Side note: the Redline mt-85 fluid has been exceptional in the trans with the clutch type lsd. No chatter, even on -5 degree start ups and it still locks uo with no issue. I can confidently say that this is the fluid I'll be running all next season. Likely mt-90 for the summer though due to the heat. I'd recommend this to anyone with a clutch type lsd in their Yaris
06YarisRSFredericton, New Brunswick, Canada · Dec 18, 2018#141
Do any of the 2zz 6 speed configurations come with an LSD? Have you considered a 2zz swap? There's your 170 - 180 hp, 8k revving engine. For fun I've been watching ebay and there's a few engine/trans combos available - imported and tested. I've looked at cams on Monkeywrench Racing as well, but stage 1.

I've also wondered if there would be room under the hood of the 2zr equipped Yaris for one of the TKC turbo kits.

All of the above purely for my entertainment, of course
tmontagueThread starterCaledonia Ont. · Dec 18, 2018#142
Turbo kit would likely fit no issue, but I'm more of a fan of high revving NA engines. Plus turbo brings more issues with heat soak and reliability problems.

Imho the 2zz is old technology, it wasnt bad and for the time it was a performance engine from Toyota (read: Yamaha) who really wasnt putting out much in that department. But those hp numbers are at the crank so it's comparing apples to oranges. A 2zr with high compression, cams and a high rev range should be able to easily match the 2zz but in a package that is already in my car and not a whole different swap.

If I was going to go to that trouble and cost I'd go with a Honda K24. 220whp NA all day. The point of where I'm going with this build over the next few years is one that you don't have to pay a shop to fabricate engine mounts and other completely custom stuff. I want to show people that they can buy a 12 year old 2nd gen yaris for cheap, gut it and do an engine swap and with bolt ons, achieve a lightweight fairly fast track car
ArmstrongRacingSan Diego · Dec 19, 2018#143
Don’t cut it up man, you’re going to miss it as a fun daily
06YarisRSFredericton, New Brunswick, Canada · Dec 19, 2018#144
Originally Posted by tmontague ↑
Turbo kit would likely fit no issue, but I'm more of a fan of high revving NA engines. Plus turbo brings more issues with heat soak and reliability problems.

Imho the 2zz is old technology, it wasnt bad and for the time it was a performance engine from Toyota (read: Yamaha) who really wasnt putting out much in that department. But those hp numbers are at the crank so it's comparing apples to oranges. A 2zr with high compression, cams and a high rev range should be able to easily match the 2zz but in a package that is already in my car and not a whole different swap.

If I was going to go to that trouble and cost I'd go with a Honda K24. 220whp NA all day. The point of where I'm going with this build over the next few years is one that you don't have to pay a shop to fabricate engine mounts and other completely custom stuff. I want to show people that they can buy a 12 year old 2nd gen yaris for cheap, gut it and do an engine swap and with bolt ons, achieve a lightweight fairly fast track car
Ah, all makes sense to me. I wasn't aware that the 2ZR could produce that power. The cams sound really promising. I did read that the 2ZZ has similar power output up to ~6500 RPM, then it comes on a lot stronger. Very informative stuff. Thanks.
Ronnie VBrampton · Dec 21, 2018#145
<2000lbs + 150whp = 1.22.9 at TMP

👍
tmontagueThread starterCaledonia Ont. · Dec 21, 2018#146
Originally Posted by ArmstrongRacing ↑
Don’t cut it up man, you’re going to miss it as a fun daily
It can still be driven in the street cut up. I just wont he dailying it. There is way to much speed left in this car is I keep it comfortable as a daily, its already past the point if a comfy daily for me

Originally Posted by Ronnie V ↑
<2000lbs + 150whp = 1.22.9 at TMP

👍
Haha yup, as long as the driver is good enough
ern-dizCA all day · Dec 21, 2018#147
Do you guys think removing the rear seat and related hardware would throw the overall balance off much, or affect rigidity? Is there a point of diminishing returns?
tmontagueThread starterCaledonia Ont. · Dec 21, 2018#148
I dont think it would affect rigidity too much and likely not enough weight to really throw off the balance. If anything it may help the rear rotate more, but probably bit a big difference
thebarberGrand Rapids, MI · Dec 21, 2018#149
Originally Posted by 06YarisRS ↑
Ah, all makes sense to me. I wasn't aware that the 2ZR could produce that power. The cams sound really promising. I did read that the 2ZZ has similar power output up to ~6500 RPM, then it comes on a lot stronger. Very informative stuff. Thanks.
My last vibe GT made 165whp with just an intake, fwiw.

But a 2zz/c60 won’t fit without cutting from rails, iirc.

I always thought the 2zr is the way to go in a Yaris..
06YarisRSFredericton, New Brunswick, Canada · Dec 22, 2018#150
Originally Posted by thebarber ↑
My last vibe GT made 165whp with just an intake, fwiw.

But a 2zz/c60 won’t fit without cutting from rails, iirc.

I always thought the 2zr is the way to go in a Yaris..
That was the 2.4 in the GT, right? Oops, disregard. Not the 2.4.