Yarisworld Archive

T Montague's 2zr swap - '08 m/t sedan some extra info

283 posts · 200,320 views · page 2 of 6

Replies continued

tmontagueThread starterCaledonia Ont. · Jun 15, 2017#51
Quick update:

Car is running strong, I do a handful of WOT runs almost every day and have had zero issues. The long term fuel trims are fluctuating between -14 and -18 consistently, the engine runs fine so this is likely d/t my aftermarket exhaust and CAI as this happened on my 1nz once I had the exhaust fabricated. I check for exhaust leaks and there are none.

With the type of driving I do I am still averaging 6.6L/100km which is really impressive so no complaints there. I have a slight oil drip coming from where I installed the adapter into the block for my oil gauge senders. I figured this would happen eventually as it was never really meant as a permanent solution.

I have ordered the oil filter adapter so I can go to a regular spin on filter and I'll be installing a glowshift sandwich adapter so I can read proper oil temps again and get rid of the oil leak. that's all for now
heeroyuy01195Florida · Jun 16, 2017#52
Thanks for the information on the rear mount in regards to the axle compression. Was a little concerned when reading this as I thought it would be the same on the liftback. Hopefully everything goes as smoothly as Cranky's swap when I swap my liftback.
tmontagueThread starterCaledonia Ont. · Jun 16, 2017#53
You shouldnt have any issues with your LB. Just keep the old Yairs mounts just in case. Easiest way to test the axles after the swap is to unweight the front wheels so the suspension is fully extended and use your hand to turn one from wheel at a time as fast as you can. Your transmission/engine should not wiggle. If that checks out then put the car in first year and let the front weels spin and you should not hear or feel any banging.

You can save yourself all this trouble and some money by just keeping all your mounts for the Yaris and only using an xd engine mount (passenger side)
heeroyuy01195Florida · Jun 16, 2017#54
Thanks for the heads up montague, read cranky's thread a while back and saw that he and frogger used all XD mounts and cables. Still weighing my options as I'm tackling suspension and braking first. Have you had any issues with the "under hood" SSK and the xD cables?
tmontagueThread starterCaledonia Ont. · Jun 16, 2017#55
No issues with the xd cables as they are longer. You can use the Yaris cables with the Yaris dogbone (i originally did) but because I want a long tube header I wanted more room at the fire wall so I installed the xd dogbone. This moves the engine forward more which than stresses one of the Yaris cables. Xd ones have no issues
CrankyOldManWest Michigan · Jun 16, 2017#56
Originally Posted by heeroyuy01195 ↑
Have you had any issues with the "under hood" SSK and the xD cables?
The engine bay SSK is starting to wear on my setup after about 5 or 6 years. I've only greased it once or twice, so that is probably a contributing factor. The cable length isn't perfect, but it fits well enough with the SSK bracket.
heeroyuy01195Florida · Jun 16, 2017#57
Thanks for the info montague and cranky, saw that Garm has a few SSK's for sale on his ebay store but wasn't sure how it would play with the swap later on. Looks like I'll be picking up one of his kits; my NST never felt right.
tmontagueThread starterCaledonia Ont. · Jun 16, 2017#58
It probably never felt right because they never made a bracket to replace the one bracket that bolts to the trans and hold the cable ends.

Garm is the only person I know of who has/had them and they change the angle that the cable where it attaches to the shift levers and makes for smoother shifting
tmontagueThread starterCaledonia Ont. · Aug 3, 2017#59
slight update:

I got back from a week long vacation and went on a short trip around the corner to find my car making a loud whistle form the engine bay when at idle. Checked the engine bay and found out that the polyethylene hose I used to plumb my dual catch cans ended up disintegrating, causing a vacuum leak which was the source of the whistle.

I looked online for oil resistance of various hose materials since finding 3/8" ID oil resistant rubber hose around here isn't as easy as I thought. Turns out PVC is oil resistant. The reason I didn't go with PVC braided line the first time was because the PE line was much more rigid than the PVC and I didn't want it to collapse under vacuum at idle.

Turns out the vacuum isn't strong enough to collapse the PVC braided hose and it is much easier to work with when running lines. Engine sounds good and is back to normal function as are my catch cans. When I removed the intake manifold I still had a slight amount of oil in it but my intake valves and chambers were extremely clean for an engine with 95k km on it thanks to my constant WOT pulls. I am collecting about 1-2 ounces of oil every 3-4k km or so.

My long term fuel trims still constantly sits at -10-12% meaning the ECU is reading that I am running rich and it is pulling fuel. Not a big deal as this is not nearly enough to trip an engine code but it is something to note. This happened on my 1nz too after I got my customs exhaust made. Doesn't seem to have any exhaust leaks either.
tmontagueThread starterCaledonia Ont. · Nov 21, 2017#60
I was able to get a hold of Tom's built transmission as he had an opportunity to buy a 6spd C60 (follow his thread HERE)

Picture not included in this copy

The transmission was torn down and inspected by Tom and any worn parts were replaced. It has a Cusco RS clutch type LSD and a Scion 4.3 final drive. This effectively increases the rpm by about 500-600 in any gear which transfers more toque to the wheels. This makes for a faster car but at the loss of fuel economy and increased engine noise at highway speeds.

Picture not included in this copy

The LSD will completely lock the axles under acceleration and even in the event of one front tire being completely lifted off the ground. This will allow me to throttle out of corners on the track and use the throttle to control over steer even more so than before. It also has the benefit of given me a true 2wd car in the winter when driving on snow/ice. The factory open diff is really a one wheel drive once you come across some ice or slippery snow.

Picture not included in this copy

I don't have access to a lift so pulling the trans absolutely sucks. The 2zr swap is wider which give you little room at all to pull the trans. I used my engine hoist to support the 100lbs transmission while I wrestled it out from under the car. Don't even try to do this by yourself without a hoist...ask me how I know. The clutch was in great condition still so I left that alone and just cleaned off the clutch fork and all contact surfaces and regreased.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

I have put a couple hundred km's on the new trans so I figured I'd post about my thoughts so far.

The good:
The very first thing I noticed is that under throttle, even partial throttle, the steering wheel wants to correct itself straight much more than before, almost forceful. Under WOT the torque steer is seemingly completely gone. It feels like I have an extra 500lbs holding down the front end to the road and 2 foot wide tires upfront. Hard to explain but the car feels much more firm and planted.

The open diff made the front end feel so light like the tires were barely touching the road. Anything more than 60% throttle in first gear would send the right tire into a spin. I feel an increased sense or confidence in the car and increased control of where it wants to go.

The bad:
noise, whines and clunks. If Tom wasn't so good at what he does or if he didn't have this in his car previous to me owning it, I would think it's broken. It is virtually silent when coasting even in full lock turns. any throttle applied and the front end locks up leading to inside tire squeal (on my winter rubber right now). When throttle is applied on a turn you hear all sorts of noises and slight vibrations. This is the plates engaging/slipping and is normal.

Accelerating in 1st or 2nd gives me a loud whine from the left of the engine bay near the trans/axle area. It sounds like my trans has straight cut gears and happens any time I give it more than 20% throttle (which is obviously all the time). I hear a whine and feel small but loud vibrations from the left front end. This is when the tires are pointed straight and it goes away when I reach 5500 rpm. Only in first and second gear.

It also clunks/knocks in between 1 and second gear shifts under hard acceleration. This is likely the clutches engaging and disengaging according to other forums online. I personally do not mind the noises, it is a daily driver but I rarely drive my wife and kid in it as we always use her vibe since it's our family vehicle. I enjoy more feedback from my car anyways.

I get both front wheels slipping under WOT in 1st gear since I currently have my winter tires installed. In the summer this shouldn't be an issue with some proper UHP summer tires. I have noticed that giving a decent amount of throttle on a corner will introduce under steer. This is easily controlled on dry pavement by easing off the throttle but on wet or slippery surfaces I could see this causing people to hit curbs and medians if they aren't expecting it and throttle hard mid corner. Crank and Tom both warned me about this so I plan on getting used to it in a snowy parking lot this winter.

All in all I'm happy with the trans and I can't wait to get out to the track next spring. This little car is becoming quite the weapon and an absolute blast to drive. It now pulls like a moster when I downshift into 4th going 110km/h to pass someone as it puts me right above 4k rpm which is in the power band on the 2zr. FWIW it revs at just under 4k rpm going 120km/h

I'll post back later on my new fuel economy numbers.

Plans for the future include BC coilovers and TRD suspensions mounts front and rear. I also just picked up my new summer rims from across the border. 15x7.5 +35 which I'll be wrapping in bfgoodrich gforce sport comp 2's. My rims I sold we're 7" wide and this will be the widest i can fit with my rear spacers and rear rolled fenders

Picture not included in this copy
atomic_hojiKincardine, ON, Canada · Nov 21, 2017#61
Nice score on the 5MT w/LSD! Likin' the purple paint job. 👍 Guess that means Tom's really sure the Celica 6MT build is going to work.. lol

New wheels look slick to. Congrats on the new toys.

-- Adam
LTHatchNewark NJ · Nov 22, 2017#62
What transmission fluid did it come with? If possible would you mind doing a few 0-60 runs?Curious to see what a 2zr with that 4.3 LSD can do vs a lightly modded 1nz.

Those wheels look damn good, how much do they weight?
tmontagueThread starterCaledonia Ont. · Nov 22, 2017#63
I am currently using Cusco's own fluid which is stupid expensive. Once that is drained I'll be using Amsoil MTG which I've been using for the past year. I called Amsoil and was told it should be fine with an lsd and I have been happy with its shifting performance plus it is a much more realistic price.

I'll do some 0-60 runs as soon as I have my summer tires on this spring and I also plan on doing a dyno run this spring. If i do 0-60 pulls now I just spin too much with my winter rubber.

Rims weigh about 11.6 a corner. It makes a huge difference in initial take off from a stop.

My butt dyno says the 2zr with 4.3 fd is much faster than a heavily modified 1nz. My 1nz had a header and full exhaust, intake manifold, 1zz TB and air intake so it's as far as you can go in regards to bolt ins with that motor. So my butt dyno has a good comparison to relate it to
tmontagueThread starterCaledonia Ont. · Nov 22, 2017#64
Some updates regarding the clunking and noise on 1st and second gear accel when going straight. Turns out this is due to my drivers side axle binding and not actual diff chatter.

I had this issue after the swap due to the trans being moved an inch or so closer to the drivers side from the 2zr being wider than the 1nz. No one else with the swap seems to have ever experienced this problem which is really strange.

This binding would only happen on sharp right turns and would cause a banging and vibration as the trans would be forced to move since the axle was maxed out with compression.

I temporarily fixed this by installing the yaris trans and doggone mount back in which pulled the engine and trans back toward the passenger side. I currently still have those mounts in my car.

I think that extra torque from the 4.3 fd and lsd are making this issue apparent again. However it only happens on very slight left or right turns when accelerating in 1st which is why I am convinced the extra torque is the reason I have this issue again.

Bottom line I need to find a proper solution as this binding caused my cv boot to tear. I spec'd some cv axles online and turns out a '98 tercel have the same splines and is 0.9" shorter than the yaris axle. I'm going to pick one up in the next week and this should fix any binding I have by giving the axle shaft more room to move under stress.

I'll post back my results
ern-dizCA all day · Nov 22, 2017#65
Man, you came to chew bubble gum and kick some ass --and you're fresh out of bubble gum. This thread is going to be a fun follow.
tmontagueThread starterCaledonia Ont. · Nov 23, 2017#66
This post may get a bit lengthy but I'll post a tl;dr at the bottom

So quick synopsis: ever since I did the 2zr swap I would experience axle bind on sharp left turns. This is a common problem on slammed Honda's and lowering as well as negative camber can lead to the issue depending on axle specs from factory. The CV axle is meant to compress and lengthen within a range so when the suspension moves up and down and the axle need to shorten and elongate you don't experience any issues. When the axle is forced to shorten more than its specs then the axle binds and this will force the transmission to move over and back repeatedly as the axle turns. This is felt by a slamming vibration and a loud consistent thud noise from the front left of the car. When I would spin the front tires (or just the right tire) I would get a violent banging in the engine bay which turned out to be the trans slamming the subframe.

I have no idea why I was the only one experiencing this since about 4 or so others who have done the swap didn't seem to have this issue. Tom is lowered and has about -1 more degree of camber up front than I have and he has never experienced the issue. The 2zr is wider and pushes your trans closer to the drivers side by an inch or so. I temporarily "fixed" it by installing my yaris dogbone bracket and trans mount on the car instead of ther xd ones I had originally installed. This "pulled" the engine over to the passenger side but the dogbone mount was now at a severe angle and the engine had to by forced over with a huge prybar to get the bolt through the trans mount bushing. Keep in mind both of those mounts on my car are full poly filled.

This seemed to reduce the noise and banging so I left it for the time being. Fast forward to my new trans with lsd and 4.3 final drive, the noise came back as did the banging. I thought at first that was how noisy clutch type lsd's are but after a day of driving I realized something was wrong and it was the dreaded axle bind. It seems the extra torque and force on the left axle is causing the issue to come back and when I re installed the trans it likely didn't go back to the exact same place as it originally was so it may have lead to the binding.

Thanks to Cranky and Tom's help I found a site to look at spline count and shaft length of CV axles (autozone is the website). I found a 2000 corolla had matching inner and outer splines but was 1.5" shorter and had an abs tone ring (possibly removable). If I went too short I risk popping out an axle which leaves it flinging around under the hood and likely cracking the trans housing or worse. Not good especially since I do track days with this car.

I tried my luck with a 98 Toyota Tercel and bingo! Same splines, option for no abs and reported 0.9" shorter. I picked one up last night an a local auto parts store for $84 CAD. and as you can see in the pics below it actually only appears to be about 0.5" shorter than the Yaris axle. It also has the same dust cap on the trans side as the Yaris axle. It seems to be missing the hub side dust cap but I realised once I installed it that it actually does have one that works the exact same as the Yaris axle.

Both axles are compressed in the pic and sitting flush against a wall. The Tercel axle (built by Cardone) also have the 3 grooves in the inner joint case to put a pry bar against when removing the axle

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

There are subtle differences such as the spline not being cut all the way back like in the Yaris axle, but once I had the yaris axle out I test the hub side with the Tercel axle and voila it worked perfectly. I installed it and check if the axle was being pulled out of the trans in the full extension of the suspension and it appeared fine.

Assembled everything back together, filled the trans with the fluid and went for a test drive. Aaaaaand silence, no more clunk, thud or loud noises. Only a slight rumble of slipping clutch plates on turns with mild throttle and of course wheel chirp on turn with more throttle as the axles lock.

The only "weird" noise I hear now is when I accelerate hard on 1st or 2nd even when the wheel is pointed straight I hear what sounds like a muffled grind from the left side of the engine bay. It does not sounds loud or damaging and it is subtle. I think it has something to do with the diff forcing the clutch plates together. Either way a clutch type lsd is definitely DDable and not nearly as noisy as I thought. Keep in mind Tom also broke it in properly with a half hour of nausea inducing figure 8's.

Cranky did mention to me that he hears a bang on hard acceleration which could be axle bind but may also be the trans hitting the subframe like mine was. It is possible that others may experience the axle bind here and there and not realise it for what it could be.

TL;DR
Bottom line a 1998 Toyota Tercel (non abs) drivers side axle will remove about 0.5-0.9" of length and fix any axle bind you have on the drivers side if you do happen to have it. It is good to know that there is an easy solution to a potential problem that those who do the swap may face. No need for custom axles or having to piece together parts from different axles, just a simple off the shelf axle will work.

Now I can do more WOT pulls without having to worry....poor tires.
atomic_hojiKincardine, ON, Canada · Nov 23, 2017#67
Good bit on information, thanks man. 🎉

Glad you go your problem solved for good (knock on wood).

-- Adam
tmontagueThread starterCaledonia Ont. · Nov 25, 2017#68
Short update:

Axle bind fixed and most of the noise is gone, however under very hard red line shifting on highway I still have the differential ear of the trans hitting the sub frame.

I will be installing the poly filled xd trans mount back which will fix the trans mount from being in a crazy angle like the current yaris on is. I'm hoping this will potentially move the trans away from the subframe.

Other possibility is that my passenger side mount is toast and worn out from me moving the engine up and down to remove the trans. However no fluid is leaking from it.

I'm getting much more engine movement from the greater torque but it shouldn't be that bad with 2 of the 3 mount poly filled.

Other option is to find a machine shop to machine a solid doggone mount which would lead to more nvh but much less movement

I'll post back how the xd trans mount works
dengMI · Nov 26, 2017#69
Nice pick up on the transmission, so jelly!
tmontagueThread starterCaledonia Ont. · Nov 26, 2017#70
Originally Posted by deng ↑
Nice pick up on the transmission, so jelly!
It's a pretty awesome mod on this car!

Update on my noise issue. The last bit of noise I had was under hard accel in 1st or 2nd gear it was a muffled vibration from the left side of the engine bay. I installed my xd poly filled trans mount and got rid of the yaris one.

The xd one was much easier to install as the mount properly lines up so the through bolt is easy to slide in. With the yaris mount its on an angle and I had to use a prybar to force the engine over and after fighting it eventually get the through bolt in.

I test drove the car and that vibration is completely gone. It must have been the through bolt hitting the outer wheel of the mount causing a muffled vibration.

I haven't driven it hard enough to find out if the trans still hits the subframe but over all it is much quieter and now only makes noise under low speed sharp turns.

Once the trans fluid heats up I'm surprised at how quiet it becomes virtually silent with no clutch chatter. Easily dd'able.

Long story short go with the xd mounts of you do the swap. Of you experience axle bind than also get a Tercel axle for the drivers side.
ern-dizCA all day · Nov 27, 2017#71
Awesome R&D and write-up, as usual. Sub'd for a future where I do this swap. Might come in very handy.
tmontagueThread starterCaledonia Ont. · Nov 27, 2017#72
Thanks. The xd axles is shorter than the Yaris axle likely due to the wider 2zr. It has different spline counts though.

I just did a wot red line 1st and second gear pull and heard a mild to moderate clunk of the trans hitting the subframe. It wasn't violent and not really a concern but I will be looking into getting a solid doggone mount machines maybe at the end of next season.
tmontagueThread starterCaledonia Ont. · Dec 23, 2017#73
I've been able to drive my car in the snow quite a bit in the past month or so and I feel like it's been enough to give a good quality update on my experience. Keep in mind this is my first time driving a car with an LSD.

I have 4 winter tires (more of an ice tire) that are relatively new as well. There seem to be two camps on line in regards to driving an LSD in snow: 1. It will help increase traction by giving you a true 2wd car instead of the realistic 1wd that open diffs give you once they slip. 2. They actually make snow/ice driving worse.

To me #1 always seemed to make more sense. In this case I'm talking about a clutch type lsd, a torsen type will not do a whole lot when your one tire is free wheeling with no traction. A clutch type lsd will lock up regardless if one wheel is free spinning.

After a month of driving in snow the only time I can see an LSD being dangerous is under hard acceleration on slick conditions. This still entirely depends on driver input, so not actually the fault of the LSD but rather the driver. If one decides to give too much throttle during cornering in icy conditions then since the axles are locked causing both tires to spin you will under steer much much more than with an open diff. This is due to both tires losing traction and not just one. This leaves you with zero traction on the front which leads you to under steer. This is easily controlled by not giving too much throttle on corners or by backing off the throttle if you start to slide and you will regain control.

In deep snow or slippery conditions the grip has improved drastically. Instead of hearing the right wheel spin up and the car barely inch forward, I now notice much less wheel spin and the car pulls forward consistently. Not like an awd obviously but it is more consistent in the progress forward.

Performance wise (as best as I can with snow tires on) torque steer is essentially zero. I can go WOT (now with much less wheel spin) and the car doesn't pull left or right. The steering wheel under throttle actually has a tendency to want to self correct back to neutral, quite powerfully actually.

Overall the car feel more planted, firm and in control, even in snow.

As for the bad:

I still have a transmission clunk that seems to happen on left turns when giving a decent amount of throttle. This does not sound or feel like axle bind, that problem was fixed with swapping in Tercel axle. It sounds exactly like the transmission hitting the subframe. This is likely due to the LSD putting extra torque out from the transmission to both wheel leading to different forces on the mounts causing excess movement.

My plan to remedy this is to get a dogbone mount machined from solid aluminum which should severely limit movement.

Overall I'm really pleased with the LSD, it really transforms the car into more of a purpose built "sports car". My gas mileage is now at about 7.1L/100km up from 6.3L/100km when I originally put the 2zr in Lfwiw it was at 5.8L/100 km with my 1nz). That said I am also on winter gas and snow tires so realistically I am probably sitting at 6.7L/100km with the 4.3 FD. The only time the LSD makes a lot of noise is when the trans fluid is still cold. Once it heats up the LSD is very quiet.
ArmstrongRacingSan Diego · Dec 23, 2017#74
I'm happy to hear the trans is proving its worth, and that you understand (and have shared) how to properly use the throttle. haha

I still dont know why your car continues to make clunking noises when mine did not. I still have a silent drivetrain even after swapping to the 6 speed. I need to buy another LSD at some point, maybe Ill try a torsion this time so I can compare
tmontagueThread starterCaledonia Ont. · Dec 23, 2017#75
I have no idea either, Toyota was obviously aware of the potential as they made the xd left side axle slightly shorter but I can't explain why you never seemed to have the issue. My car was never in an accident that I'm aware of and there is no evidence to ever say it was.

The noise/banging I'm hearing now is simply the war of the trans hitting the subframe. My only guess is I prematurely wore out my fluid filled passenger side mount from moving the engine up and down with it still connected when removing my trans twice. However the doggone mostly is the only mount controlling that engine movement and mine is fully poly filled.

I'm hoping the solid billet doggone will fix the issue, if not it isn't that bad and shouldn't be an issue on the track. Problem is the xd is such a rare car that there is little to no aftermarket for it other than show parts.

As for the torsen lsd, I've never used one but I was originally conceded about dding a clutch type based on online comments. After having daily'd it for the past little while, it is no issue at all. Most comments online is the same comment regurgitated, very few people spoke from experience.

If costs were equal, I'd go clutch type every time. Never have to worry about lifting a wheel or having minimal grip on the inside causing it to act like an open. Yes, eventually the clutches will need to be replaced but according to many users online the cusco 1 way lsd last a darn long time. Not many draw backs of you like to hear your car and feel everything. If you want oem comfort and silence than torsen is a great compromise.

I've been very please this far
tmontagueThread starterCaledonia Ont. · Jan 25, 2018#76
Finally picked up my new summer tires and had them mounted to my new Konig Hypergram 15x7.5
tires are 195/55 r15 and are as wide as most 205's
treadwear is 340

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

can't wait for spring to get these things on the road!
atomic_hojiKincardine, ON, Canada · Jan 25, 2018#77
Nice! 👍

Congrats on the beauty wheel and tire setup. Should look slick man.

-- Adam
Jeanseb29Gatineau (Ottawa), Canada · Jan 27, 2018#78
What brand of tires did you choose Tmontague? I can't tell from the photos... I'm currently looking for summer tires with same dimensions (195/55r15) for a set of Rota circuit 8 (15x6.5) I found on Kijiji before winter. I might go with Yoko s-drive but still not decided yet.

Sent from my SM-N910W8 using Tapatalk
dengMI · Jan 27, 2018#79
The hypergrams look great!

Jean, those are BF Goodrich G Force Sport 2s.
tmontagueThread starterCaledonia Ont. · Jan 27, 2018#80
Yup, Deng is correct bfg g force sport comp 2's. I forgot to put that in my post. In any other tire I would have went 205 but these bad boys are wide.

I chose they over any other UHP tire as we get a decent amount of rain where I live. I was tired of having to limp my Yaris around whenever it rained so I wanted a tire that performed well in the wet. The reviews on the sport comp 2's are some of the best and excellent in the wet. Made sense especially with their price. Found them on eBay for approx $64 a corner. Stupid cheap and better performing than many others.
thebarberGrand Rapids, MI · Jan 28, 2018#81
Nice!
malibuguyWestminster, MD · Jan 29, 2018#82
64 a piece hotdamn
tmontagueThread starterCaledonia Ont. · Jan 29, 2018#83
Originally Posted by malibuguy ↑
64 a piece hotdamn
Yup stupid good price. This was slightly cheaper than DTD's latest sale price. With mounting and taxes at the border I ended up paying $370 CAD! The cheapest I could find them in Canada all in was $600 CAD.

The reason why they were marked down cheaper is likely due to the fact that they were manufactured midway through 2015. This shouldn't be an issue for me as this tire probably won't last more than 3 years before it's down to the wear bars. This puts it at 6 years old which is when I ideally like to get new tires (if I have the cash).

If I ever get to the track and it's raining I plan on using these as well as for any autox I do this year. My slicks take too long to hear up for autox and are downright greasy when cold.
thebarberGrand Rapids, MI · Jan 29, 2018#84
nothing wrong with new old stock
tmontagueThread starterCaledonia Ont. · Jan 29, 2018#85
Originally Posted by thebarber ↑
nothing wrong with new old stock
Absolutely not as long as they aren't a decade old and dry rotted lol. 2 and a half years is no problem and a faster wearing tire
tmontagueThread starterCaledonia Ont. · May 3, 2018#86
Thought I'd toss out an update on what I've done thus far. In preparation for my first upcoming track day of 2018 at the end of next week I spent some time this week working on the car. I now have my summer rubber and rims mounted (BF Goodrich sport comp 2's) they are a 340 tread wear tire and F%ck these things grip like you wouldn't believe.

I have been constantly pushing them harder and harder and not even a squeal form either corner. They just grip more the harder you push them - highly recommend these for a spirited DD'r that sees a lot of rain

I recently decided to get my car a proper corner balance and race alignment at a somewhat local race shop to me. My current alignment specs are as follows:

Rear: Camber L-1.42 R-1.48
Total toe -0.18 (toe out)

Front: camber L-2.6 R-2.5
total toe -0.08 (toe out)

according to the alignment guy who is a well decorated racer and has a couple decades of experience building suspension and doing alignment on race cars the set up is optimised for the track but still conservative enough where it will still be able to drive in snow on roads without spinning out all the time. The rear end toe was properly corrected using shims which was never perfect due to my camber washers I was using.

Picture not included in this copy

I'm still blown away at how light these cars are, without me in the car it came in at 2370lbs give or take and that was with a 3/4 tank of gas. My initial impressions on the drive home was how fast the turn in is now. The difference is night and day, almost as if I have a close ratio steering rack now. You have to be very aware driving the car now as a slight movement in the steering wheel will cause the car to quickly flick left or right. The cars feels much more stable now and planted and the suspension doesn't feel as jumpy in the rear end.

I installed some new rotors up front as the others were fairly glazed and getting rusty from this winter. I didn't go for the Stoptech slotted rotors as they would have been $150 CAD for both off of RockAuto. Instead i went for the Stoptech regular rotors that are coated to prevent rust. They cost $48 CAD for both. I couldn't justify the extra $100 for the slotted/directional ones, not on a car this light.

I also threw in some new spark plugs, the Denso's did the job and had about 125k km on them so I threw in some NGK's. If I was just DDing the car I would have left the Denso's in there but seeing as my car gets driven fairly hard and often, I figured the NGK's weren't a bad idea and now at least I know I'm starting fresh. As usual I also re greased all of the ignition connectors.

I also tuned up the brakes and re lubed all the sliders and contact points as the high heat from the track isn't friendly to keeping these things running smooth. I used high temp grease that came with the Hawk brake pads. I have about 300km of track driving on these pads and they still have 50% life left, so pretty impressive. They are the Hawk HPS pads and I daily on these as well.

Lastly I installed a 2.5 lb BC type fire extinguisher and to mount it I used a product called the Bracketeer. I ended up mounting it behind the passenger seat as it is a great position for offsetting the driver weight and it is very easy to access with a slight reach around.

Picture not included in this copy

having it in front of the driver seat wouldn't work with the stock Yaris seat brackets due to my seat position and the steering wheel gets in the way of easily accessing it anyways. Plus it just adds weight to the wrong side of the car. This is something I really wanted in my car. A cart fire is a very quick way to ruin something you've spent countless hours on and it is also a terrible way to die if the worst case scenario ever happens. A fire extinguisher will help you quite a bit in either scenario.

I chose a BC type over an ABC type as the A is for wood fires and is a very corrosive chemical to metal and electrical wires. Cars are fine with BC type extinguishers and other than a lot of mess from the dry powder it tends to not corrode your car and leads to less damage you have to repair if you ever have to use your extinguisher. This particular extinguisher is good for 10 seconds which is pretty good as many tend to only last 5secs.

After a lot of thinking and talking to some people including my wife I have changed future plans in terms of what car I will be using as a dedicated track build. I'll save this for another post - hint, it starts with a Y and ends in aris... 😉
ern-dizCA all day · May 4, 2018#87
👍
tmontagueThread starterCaledonia Ont. · May 13, 2018#88
Did a shakedown on Friday after about 8 months away from the track. Weather was about 6 degrees (C) ambient temps and off and on drizzle of rain. The BFG R1's I'm running never got up to temps and stayed squirmy each session. I timed my first session and was a few seconds slower than my fastest lap last year.

By the 3rd session I blew a rear tire which sent me in a spin and into the grass a bit. Turns out I picked up a screw or nail and when it ripped out it lost all the air suddenly and I lost control. Luckily I'll be able to patch/plug the tire from the inside and hopefully still get some more track days on the rubber. There is still some left in them and indidnt want to have to scrap the tires so soon.

The R1's are a great tire for hour long racing and stick like hell, but if you do track days in cool temps then youre better off with the r1s. The Yaris is a light car so tires take longer to heat up

My car ran great, oil temps peaked at 250F and I had no issues. I still have the transmission banging on the subframe under hard shifts so I'll have to build a proper poly mount soon, the one i currently have installed was half assed and not stiff enough.

Not a great day on the track, but my expectations were also too high. In the future I won't be timing my first session of the year, especially when the tires aren't heating up. I'll be back again in 3 weeks with hopefully hotter ambient temps and no rain.

As a side note, i got to try my sport comp 2's in the rain and wow do they ever hook up. Hell, they almost ran better than my r1's when it was dry.
DarkShadowFoxMassachusetts · May 19, 2018#89
I looked into the 2zrfe swap and i think i will be doing it too seems to be almost a direct drop in like legos. will be nice cause its about 37 pounds lighter then the 1zfe at more displacement and more power for the cost of nothing. also you get to go to 5x100 which allows bigger and better things :D
enviriCT · May 19, 2018#90
Originally Posted by DarkShadowFox ↑
will be nice cause its about 37 pounds lighter then the 1zfe at more displacement and more power for the cost of nothing.
*21.8 kg heavier.
tmontagueThread starterCaledonia Ont. · May 19, 2018#91
Originally Posted by DarkShadowFox ↑
. also you get to go to 5x100 which allows bigger and better things :D
It's not required to go to 5x100 w/ the 2zr swap and really is completely separate from the swap. Afaik no one who has done the swap has often to spend extra for 5x100, I personally didn't see a reason to worth the money

I agree it is a worthwhile swap though
atomic_hojiKincardine, ON, Canada · May 23, 2018#92
^^^ +1 😕 Not sure I've seen anyone mention a 5-lug conversion when doing the 2ZR swap; or I've missed something critical.. lol

Good to see the work on the car and that you're setup is shaking down well for you! 👍 Hopefully we'll catch up at a track day this summer.

Interesting note about the fire extinguisher - I've always bought ABCs out of habit; generally to use around the house. Good to keep in mind for a dedicated extinguisher in the car.

-- Adam
DliveranceElma Washington · Jun 12, 2018#93
Originally Posted by tmontague ↑
It's not required to go to 5x100 w/ the 2zr swap and really is completely separate from the swap. Afaik no one who has done the swap has often to spend extra for 5x100, I personally didn't see a reason to worth the money

I agree it is a worthwhile swap though
I’m not a fan of 5x100 either. Coming from a long history of Subaru’s and celica’s, the only decent wheels I ever found in 5x100 were a set of rota grid v in 17x8.
thebarberGrand Rapids, MI · Jun 12, 2018#94
5x100 would make it tough to find 15" wheels. 16" might be ok...but you'd likely end up with OEM matrix or vibe wheels!

4x100 is so much easier to find wheels in 15"
DarkShadowFoxMassachusetts · Jun 12, 2018#95
Originally Posted by thebarber ↑
5x100 would make it tough to find 15" wheels. 16" might be ok...but you'd likely end up with OEM matrix or vibe wheels!

4x100 is so much easier to find wheels in 15"
just use corolla wheels, FRS BRZ rims... subaru wheels.
RunethecursedSocal · Jun 12, 2018#96
Subaru impreza pre 2009 where all 5x100. all the way back to i think 1996? whatever the first years of the Impreza GC/GM chassis was
tmontagueThread starterCaledonia Ont. · Jun 30, 2018#97
Another update after some track days.

a few weeks ago after my first 45min session I noticed my coolant reservoir was almost empty. It was a hot day (ambient temps around 90F) and there was dry coolant on the bottom of my engine splash guard. I figured I had a leak. No leaks seen so I topped it up with water and kept going. It would drop a bit each session but was not leaking out of anywhere and it wasn't being burnt through the exhaust.

I put a new rad cap on when I got home and checked it every day the next week. The coolant never dropped an ounce. Long story short, my rad cap likely wasn't holding pressure which caused it to boil slightly and spill out of the reservoir. The next track day I had no coolant loss and it was almost just as warm. The coolant temps tend to hit max 212F and typically stay between 195 and 204F during hard lapping (oil temps peak at 260F)

On my last track day I worked on braking zones. I had a fellow YW member (Brian sp?) drive around with me during some hot laps and he commented that I could brake much later (which was true). I had focused a lot on turn in's apexes and car control using throttle and brake. I felt like I had that down and wasn't making up any more time so braking zones it was.

First off it is scary as shit as your brain is basically yelling at your to brake and you are holding off until last minute. I got to the point where I'd brake late enough that let me scrub off as much speed as possible just to make the corner. Problem is at these limits there is very little room for error. Miss or slip off the brake pedal during heal toe shifts and you are done.

That is exactly what happened. After 3, 45 mins session and over 100km around the track, I had shaved 3 seconds off of my PB. I am now down to a 1:30:32. This is a relatively quick time, especially for the car I am in. On my 3rd session I was actually on par to beat that time but kept running into other people on the track and having to slow down. At those track times I was one of the faster cars that day. This was all due to braking later.

I felt I was getting tired so I was only going to go out for a 4th and last session - it's amazing how tiring it is when you drive the car 10/10ths and brake late, compared to going 8/10ths and having room for error. On the 4th last when the tires were hot I was heading into turn 2. This is a 90 degree corner that follows a straightaway that I hit about 145km/h on. To make the turn on my r compound tires I need to scrub my speed down to about 95km/h. I hit my brake zone and slammed on the brakes, at the same time heel toe'd down into 3rd (I have a reduced final drive) which is an aggressive heel to as I have to get the revs up to redline so as to not upset the balance of the car.

As I heel toed, I slipped off the brake and all of the weight of the car lifted. I was only down to about 125-130 km/h. At this point I couldn't get back on the brakes as I would have sent myself into a spin since I now had to turn in. So I just rode out the corner and kept the car as balanced as possible. During the corner the car slide off to the outside and into a field pretty hard. The issue was a 1' ditch right off the track before the field. I thought I was going to flip once I hit the ditch, but luckily the car was low enough that it just hit violently, made a big cloud of dust and spun once in the field before coming to a stop.

I limped back to the paddock and called it a day. I swapped out my tires to head home and checked for damage. Front left wheel was loose (not the lug nuts) and both rear wheels were loose. I thought I had blown 3 wheel bearings. Inspected it when I got home and turns out the front axle nut worked itself very loose (it was torqued to spec at 160 ft/lbs). I re tightened both axle nuts to 170 ft/lbs and the bearing tightened up.

There rear bearings were both shot, but the left was much worse, it made the car feel very twitchy and all over the place. The rear bearings I had on were premium Moog bearing with less than 14 months on them. It was likely the crash that turned them it though so I cannot comment on quality. I decided to replace them with mid grade bearings with only a 12 months warranty. So far so good we'll see how long they last.

Cars is back to being fully operational, I have a track day next Friday and the plan it to get my lap times down to a sub 1:30. Getting into the 1:29's would be awesome in a streets legal Yaris. Bottom line - don't miss the pedal! and dont head out for another session when you are fatigued!
atomic_hojiKincardine, ON, Canada · Jun 30, 2018#98
😲

Glad to hear you're making progress with your driver skills, that's awesome! Not so awesome the car took some damage, but sounds like overall she needed a few parts and is back up to par, so that's good. 👍 Sounds like it could have been way worse - always the ditch diving that does the damage.. lol

Do you run a dashcam? Would be interesting to see your laps and the big slide (knowing it turns out ok.. 😉).

-- Adam
tmontagueThread starterCaledonia Ont. · Jun 30, 2018#99
I do have a dashcam which initially was strictly for insurance/accident purposes. That said, there is no reason I can't pull footage from it during track days. I honestly have never done so before as I fortunately have not been hit so I have had no reason.

I think I'll get a micro sd adapter and play around with it and see if I can pull footage of the crash. It would be good to review my laps
ern-dizCA all day · Jul 2, 2018#100
Originally Posted by atomic_hoji ↑
😲

Glad to hear you're making progress with your driver skills, that's awesome! Not so awesome the car took some damage, but sounds like overall she needed a few parts and is back up to par, so that's good. 👍 Sounds like it could have been way worse - always the ditch diving that does the damage.. lol

Do you run a dashcam? Would be interesting to see your laps and the big slide (knowing it turns out ok.. 😉).

-- Adam
+1 on all points. Glad it wasn't worse and it would be cool to see lap footage (not for off's specifically lol but it would be interesting).