That's not too shabby for just an intake. If someone was looking to compare bone stock engines and didn't mins the frame (and money wasnt as issue) then yes a 2zz would make the most sense. But when looking into aftermarket parts and running a standalone ecu I think the 2zr makes a lot more senseOriginally Posted by thebarber ↑My last vibe GT made 165whp with just an intake, fwiw.
But a 2zz/c60 won’t fit without cutting from rails, iirc.
I always thought the 2zr is the way to go in a Yaris..
T Montague's 2zr swap - '08 m/t sedan some extra info
283 posts · 200,320 views · page 4 of 6
Replies continued
I received an online gift card from my work for the holidays so I put it to use on Amazon. Ordered a proper catch can to replace my dual air compressor air/water separators. I also picked up a Mishimoto magnetic transmission plug as per Tom's recommendations. It was priced fairly well and it seems like a good idea since I have a clutch type lsd.
I had some extra cash left over so I also ordered a TRD radiator cap. It is overpriced for what it is but the online gift card was very limiting on where I could use it and Amazon Canada isn't great for automotive part inventory. It's more of a "just in case" part. I will be properly dealing with the cooling issues with a dual core radiator in the summer, but the extra pressure that the TRD cap offers is just some extra protection from boiling in case something goes wrong and the coolant temps creep up again.
I also found a local guy about an hour away who was parting out his 2000 Echo that his buddy crashed. I pulled the radiator hoses, fan shroud and coolant fill neck. They are all in surprisingly good condition, I'm assuming the hoses had been replaced one time in their life. All I need now for the rad swap is an ebay dual core radiator and I'll probably also order some silicone hoses too just in case.
That's all for now, I'm anxiously awaiting updates on the long tube header ;)
I had some extra cash left over so I also ordered a TRD radiator cap. It is overpriced for what it is but the online gift card was very limiting on where I could use it and Amazon Canada isn't great for automotive part inventory. It's more of a "just in case" part. I will be properly dealing with the cooling issues with a dual core radiator in the summer, but the extra pressure that the TRD cap offers is just some extra protection from boiling in case something goes wrong and the coolant temps creep up again.
I also found a local guy about an hour away who was parting out his 2000 Echo that his buddy crashed. I pulled the radiator hoses, fan shroud and coolant fill neck. They are all in surprisingly good condition, I'm assuming the hoses had been replaced one time in their life. All I need now for the rad swap is an ebay dual core radiator and I'll probably also order some silicone hoses too just in case.
That's all for now, I'm anxiously awaiting updates on the long tube header ;)
I like free parts!
Welp, I installed my Mishimoto magnetic transmission plug this weekend (went in without any issues into the fill hole), and while in there I inspected my engine bay to make sure everything was Kosher. Sure enough, I find some greenish yellow a/c die around my low pressure discharge hose that goes into the compressor. My first thought "well its a darn good thing I added dye into the system as it makes diagnosis much easier". My second thought was "damn, my a/c system is now toast" - I haven't actually confirmed 100% but it appears my 11 year old low pressure hose has blown all the refrigerant out at the metal/rubber crimp. A common place of failures, especially on Nissan's and it appears this just happened to be due to age.
No hoses were rubbing and everything looked sound. Now I'm faced with the dilemma, do I spend around $100 CAD for an aftermarket hose, plus r134 (which I already have) and the hour or so repairing the leak for just one more summer of DDing the car, or do I pocket the cash and strip out all my a/c components now and put my car on a 30-40ish pound diet?
For me it is an easy answer but keep in mind I will be picking up my son occasionally from day care this summer and it is nice to have a/c for him as well as anytime I am dressed nicely and heading to a dinner or something and don't want to sweat my through my clothes. At this point I have convinced my wife to just leave the a/c system no functioning for the rare occasion I am picking up the kids in my car and it happens to be 35 degrees C out. When I stripped my interior, I kept the window switches connected and zip tied so I still have full control of the windows on those hot days.
It looks like my car will become a bit lighter over the next couple months, albeit a whole lot hotter this summer...
I also loosely test fitted the 1st gen radiator and it appears that the upper rad hose will clear the 2zr without issue. The problem point will actually be the DC sports CAI as the throttle body on the 2zr is at an upward angle compared to the mose straight 1nz TB. I am either going to have to find a comparable 30mm upper hose form another car or just put some sort of rubber material between the hose and the intake tube as they will likely be rubbing. The problem is I will not actually know how well it will or won't work until the new rad and shroud are in their actual places. This will likely have to be saved until the spring when I drain my winter coolant for the summer stuff ansd then I can mix and match the rads without making a mess
No hoses were rubbing and everything looked sound. Now I'm faced with the dilemma, do I spend around $100 CAD for an aftermarket hose, plus r134 (which I already have) and the hour or so repairing the leak for just one more summer of DDing the car, or do I pocket the cash and strip out all my a/c components now and put my car on a 30-40ish pound diet?
For me it is an easy answer but keep in mind I will be picking up my son occasionally from day care this summer and it is nice to have a/c for him as well as anytime I am dressed nicely and heading to a dinner or something and don't want to sweat my through my clothes. At this point I have convinced my wife to just leave the a/c system no functioning for the rare occasion I am picking up the kids in my car and it happens to be 35 degrees C out. When I stripped my interior, I kept the window switches connected and zip tied so I still have full control of the windows on those hot days.
It looks like my car will become a bit lighter over the next couple months, albeit a whole lot hotter this summer...
I also loosely test fitted the 1st gen radiator and it appears that the upper rad hose will clear the 2zr without issue. The problem point will actually be the DC sports CAI as the throttle body on the 2zr is at an upward angle compared to the mose straight 1nz TB. I am either going to have to find a comparable 30mm upper hose form another car or just put some sort of rubber material between the hose and the intake tube as they will likely be rubbing. The problem is I will not actually know how well it will or won't work until the new rad and shroud are in their actual places. This will likely have to be saved until the spring when I drain my winter coolant for the summer stuff ansd then I can mix and match the rads without making a mess
Sure that's not because there is extra tension on there as the distance to the port with the 2ZR swap is a bit farther? Is it the crimp at the bottom of the low pressure side? Mine has some tension on it too, though much less than before I bent the aluminum tube part. I think the engine rocking back and forth a bit with that tension might fatigue the rubber where it's crimped.Originally Posted by tmontague ↑...it appears my 11 year old low pressure hose has blown all the refrigerant out at the metal/rubber crimp.
Once you ditch your condensor, you can put a nice big oil cooler on there, LOL!
Have you done the spin-on oil filter conversion? Can't recall if you mentioned that.
That's a possibility but I rechecked it tonight and the hoses have virtually no stress on them. I spent time when I did the swap bending the metal part of the hose in a vice and re doing it a bunch so the rubber part had no excess stress on it.
That said it is a complete possibility since it isnt a known issue for these hoses to regularly fail on the Yaris.
I did do the filter conversion - so that I could install a sandwich plate for my oil temp and pressure gauges. I dont think I'll be getting an oil cooler. Last season with crazy hot ambient temps and my coolant running at 234 degrees I only peaked oil temps at about 285F. Once I have the larger radiator in there the problem should only improve.
I am awaiting my most recent UOA from Blackstone which I will post up here once i look at it. There should be no reason the oil cannot handle those temps. I will however be running a 40weight oil next season so the viscocity stays up to spec in those temps
That said it is a complete possibility since it isnt a known issue for these hoses to regularly fail on the Yaris.
I did do the filter conversion - so that I could install a sandwich plate for my oil temp and pressure gauges. I dont think I'll be getting an oil cooler. Last season with crazy hot ambient temps and my coolant running at 234 degrees I only peaked oil temps at about 285F. Once I have the larger radiator in there the problem should only improve.
I am awaiting my most recent UOA from Blackstone which I will post up here once i look at it. There should be no reason the oil cannot handle those temps. I will however be running a 40weight oil next season so the viscocity stays up to spec in those temps
Although 285 for even a second would freak me out, here is a quote from BITOG - and it's for GF-4, not the current GF-5:Originally Posted by tmontague ↑That's a possibility but I rechecked it tonight and the hoses have virtually no stress on them. I spent time when I did the swap bending the metal part of the hose in a vice and re doing it a bunch so the rubber part had no excess stress on it.
That said it is a complete possibility since it isnt a known issue for these hoses to regularly fail on the Yaris.
I did do the filter conversion - so that I could install a sandwich plate for my oil temp and pressure gauges. I dont think I'll be getting an oil cooler. Last season with crazy hot ambient temps and my coolant running at 234 degrees I only peaked oil temps at about 285F. Once I have the larger radiator in there the problem should only improve.
I am awaiting my most recent UOA from Blackstone which I will post up here once i look at it. There should be no reason the oil cannot handle those temps. I will however be running a 40weight oil next season so the viscocity stays up to spec in those temps
"...GF-4 certification is on the bottle of the oil in your crankcase, it has passed the Sequence IIIG test which exposes the oil to 300F degrees for 100 hrs at 3600 rpm."
It sounds like you're definitely ok. I assume your running a synthetic?
I really like the idea of doing the spin-on upgrade.
The spin on conversion really has no benefit unless you need/want to run a sandwich adapter for gauges.
I actually prefer the original set up as it makes it much easier to view the filter and any particulates that were caught.
I do run off the shelf full synthetic oils, the current sample I'm waiting on is Pennzoil ultra platinum 5w30 and my past UOA's were with Mobil 1 0w30. Unfortunately PUP and even PP isnt available locally in a 40 weight so I'll be switching to something else.
I have so far had no reason to need a boutique brand oil that costs much more. Even grade III synthetics are very stout oils and can easily compare to many IV's as they just have that many more additives to make up for it.
The next oil I have been eyeing in Canadian Tire's Formula 1 (made by Shell) as they have a 0w40 euro spec. The Euro specs have a much higher HTHS due to their use of the autobahn. This obviously pairs well with my track use.
Overall temp of a full syn oil isnt really the issue - it is the cause of the issue. If the oil thins too low then lowering temps can help that. Alternatively you can run a higher weight oil that will maintain factory spec viscocity at those higher temps. The 2zr is a factory spec'd 20 weight oil in NA but a 30 weight in hotter climates (allegedly) this is based on 212F summer oil temps of normal use. Based on my research a 40 weight should bring me closer to those viscocities at 260-280F I typically run at on track
I actually prefer the original set up as it makes it much easier to view the filter and any particulates that were caught.
I do run off the shelf full synthetic oils, the current sample I'm waiting on is Pennzoil ultra platinum 5w30 and my past UOA's were with Mobil 1 0w30. Unfortunately PUP and even PP isnt available locally in a 40 weight so I'll be switching to something else.
I have so far had no reason to need a boutique brand oil that costs much more. Even grade III synthetics are very stout oils and can easily compare to many IV's as they just have that many more additives to make up for it.
The next oil I have been eyeing in Canadian Tire's Formula 1 (made by Shell) as they have a 0w40 euro spec. The Euro specs have a much higher HTHS due to their use of the autobahn. This obviously pairs well with my track use.
Overall temp of a full syn oil isnt really the issue - it is the cause of the issue. If the oil thins too low then lowering temps can help that. Alternatively you can run a higher weight oil that will maintain factory spec viscocity at those higher temps. The 2zr is a factory spec'd 20 weight oil in NA but a 30 weight in hotter climates (allegedly) this is based on 212F summer oil temps of normal use. Based on my research a 40 weight should bring me closer to those viscocities at 260-280F I typically run at on track
Here's some pics of the refrigerant leak
Picture not included in this copy
Picture not included in this copy
as you can see, it appears to be blowing out of the crimp on the low pressure hose. For any future 2zr swap I would recommend replacing this hose with the proper xd hose. It is a relatively inexpensive part and is much easier to do when the a/c system is already apart.
There is no way to know if this was due to the yaris hose being too stressed or if it is just age, so better to be safe than sorry. FWIW, it appears the leak has gotten bigger over the past 2 days so I think it is still blowing out. I'll likely remove my ac system this weekend if I can secure a belt locally for cheap.
I also started something new last night. For a while I've notive the front grill is fairly restrictive to air flow and I wanted to do something about it but wasn't sure what. The winter time when I'm itching to work on my car is a good time for these things. Now that the car is becoming more and more of a track rat, I am concerned less about looks and more about function. I removed the front grills and just threw in some gutter guard that I picked up for $5 at my local CT.
Picture not included in this copy
I actually prefer the larger mouth of the grill removed and it is definitely much larger. That said, if I wanted this to look good I would use some chicken wire painted black as this gutter guard is fairly flimsy and bends and caves. As i said, I'm not concerned with that as I don't care much about making this look really good. I still have to do the lower grill this weekend. The upper grill has holes which makes it really easy to use as attachment points for zipties. The lower grill I will have to drill some hole to run zipties into.
I had originally removed the black plastic piece that sits under the upper front bumper so I could access my horns much easier if I needed to work on them (I had issues with them in the past that are now fixed). I realized now that there is a huge gap for the air to blow over the rad without that plastic piece. I will be clipping that back in so it directs the air through the radiator instead.
There is a lot more width to fit a much wider radiator in the front of the engine bay and there are even extra holes in the upper and lower rad supports. I'm curious what other radiator would be an almost direct drop in. The problem is finding the proper hoses to work with the engine and not obstruct anything else. I think for now it is best to just stick with what is known to work and go with a dual core 1st gen radiator. Others have run these in the past and they seem to offer more than enough cooling.
I hate a cluttered engine bay, I'm looking forward to getting rid of the a/c system and eventually relocating the battery. For the time being my cash is being saved until news comes in for the long tube header and the midpipe work I will need done from a local shop.
Picture not included in this copy
Picture not included in this copy
as you can see, it appears to be blowing out of the crimp on the low pressure hose. For any future 2zr swap I would recommend replacing this hose with the proper xd hose. It is a relatively inexpensive part and is much easier to do when the a/c system is already apart.
There is no way to know if this was due to the yaris hose being too stressed or if it is just age, so better to be safe than sorry. FWIW, it appears the leak has gotten bigger over the past 2 days so I think it is still blowing out. I'll likely remove my ac system this weekend if I can secure a belt locally for cheap.
I also started something new last night. For a while I've notive the front grill is fairly restrictive to air flow and I wanted to do something about it but wasn't sure what. The winter time when I'm itching to work on my car is a good time for these things. Now that the car is becoming more and more of a track rat, I am concerned less about looks and more about function. I removed the front grills and just threw in some gutter guard that I picked up for $5 at my local CT.
Picture not included in this copy
I actually prefer the larger mouth of the grill removed and it is definitely much larger. That said, if I wanted this to look good I would use some chicken wire painted black as this gutter guard is fairly flimsy and bends and caves. As i said, I'm not concerned with that as I don't care much about making this look really good. I still have to do the lower grill this weekend. The upper grill has holes which makes it really easy to use as attachment points for zipties. The lower grill I will have to drill some hole to run zipties into.
I had originally removed the black plastic piece that sits under the upper front bumper so I could access my horns much easier if I needed to work on them (I had issues with them in the past that are now fixed). I realized now that there is a huge gap for the air to blow over the rad without that plastic piece. I will be clipping that back in so it directs the air through the radiator instead.
There is a lot more width to fit a much wider radiator in the front of the engine bay and there are even extra holes in the upper and lower rad supports. I'm curious what other radiator would be an almost direct drop in. The problem is finding the proper hoses to work with the engine and not obstruct anything else. I think for now it is best to just stick with what is known to work and go with a dual core 1st gen radiator. Others have run these in the past and they seem to offer more than enough cooling.
I hate a cluttered engine bay, I'm looking forward to getting rid of the a/c system and eventually relocating the battery. For the time being my cash is being saved until news comes in for the long tube header and the midpipe work I will need done from a local shop.
Great explanation. I have done quite a bit of reading over the past few years at BITOG. I used to always buy synthetic, but have since returned to conventional. I'm always monitoring my coolant and oil temps in my van as Kia makes many more sensors available than Toyota. I can't get oil pressure, however. After driving for a bit, oil temps are usually ~10 - 15 degrees higher. If I apply the same logic to my Yaris, even under extreme conditions - such as bumper to bumper traffic in August - there would never be a need for anything other than an API conventional. In my old Dodge grand Caravan, I installed a homebuilt tee and monitored both oil temp and pressure with cheap electrical gauges. I also tapped the transmission lines for both a Magnaflow and temp sensor.Originally Posted by tmontague ↑The spin on conversion really has no benefit unless you need/want to run a sandwich adapter for gauges.
I actually prefer the original set up as it makes it much easier to view the filter and any particulates that were caught.
I do run off the shelf full synthetic oils, the current sample I'm waiting on is Pennzoil ultra platinum 5w30 and my past UOA's were with Mobil 1 0w30. Unfortunately PUP and even PP isnt available locally in a 40 weight so I'll be switching to something else.
I have so far had no reason to need a boutique brand oil that costs much more. Even grade III synthetics are very stout oils and can easily compare to many IV's as they just have that many more additives to make up for it.
The next oil I have been eyeing in Canadian Tire's Formula 1 (made by Shell) as they have a 0w40 euro spec. The Euro specs have a much higher HTHS due to their use of the autobahn. This obviously pairs well with my track use.
Overall temp of a full syn oil isnt really the issue - it is the cause of the issue. If the oil thins too low then lowering temps can help that. Alternatively you can run a higher weight oil that will maintain factory spec viscocity at those higher temps. The 2zr is a factory spec'd 20 weight oil in NA but a 30 weight in hotter climates (allegedly) this is based on 212F summer oil temps of normal use. Based on my research a 40 weight should bring me closer to those viscocities at 260-280F I typically run at on track
One synthetic I do did buy occasionally, and will still buy when it goes on clearance at Walmart USA is the SuperTech Full Synthetic. The last 6 jugs I bought, I think i paid $12.00 a jug for. According to some reports it's not a superlative looking oil on paper - with a relatively low TBN - but fares really well in UOAs.
As for the spin on filter, at some point I expect that I might add a sandwich plate and gauges since I can't get this data from OBD. And, in the unlikely event that I decide to significantly ungrade the 2ZR performance, this would obviously come in handy.
oddly enough I have found that currently during the winter, oil temps hover about 10 degree lower than coolant (coolant stays around 181F) but on the highway when I'm hovering around 3.5k rpm, the oil is either equal or slightly higher than the typical 185F coolant temp.Originally Posted by 06YarisRS ↑Great explanation. I have done quite a bit of reading over the past few years at BITOG. I used to always buy synthetic, but have since returned to conventional. I'm always monitoring my coolant and oil temps in my van as Kia makes many more sensors available than Toyota. I can't get oil pressure, however. After driving for a bit, oil temps are usually ~10 - 15 degrees higher. If I apply the same logic to my Yaris, even under extreme conditions - such as bumper to bumper traffic in August - there would never be a need for anything other than an API conventional. In my old Dodge grand Caravan, I installed a homebuilt tee and monitored both oil temp and pressure with cheap electrical gauges. I also tapped the transmission lines for both a Magnaflow and temp sensor.
One synthetic I do did buy occasionally, and will still buy when it goes on clearance at Walmart USA is the SuperTech Full Synthetic. The last 6 jugs I bought, I think i paid $12.00 a jug for. According to some reports it's not a superlative looking oil on paper - with a relatively low TBN - but fares really well in UOAs.
As for the spin on filter, at some point I expect that I might add a sandwich plate and gauges since I can't get this data from OBD. And, in the unlikely chance that I decide to significantly ungrade the 2ZR performance, this would obviously come in handy.
In the middle of summer coolant will typically be 188-194F on the highway and oil around 212F. In stop and go traffic mid summer coolant peaks around 212F but tends to stay at 202F and oil around 220F max.
During 45min track session coolant stays between 220 and 235F and oil gets up to 265-290F.
I run off the shelf syn oil in all my cars simply due to the really cold winters here and how much easier it is to start them. Even my awd Vibe, gets 0w30 and syn gear lube in the differential. I have found the morning start ups much smoother, especially up North at the cottage after it sits over night. It's true that a dino 5w30 would still be pumpable at these temps, but a syn oil is that much less viscous and easier to pump, meaning easier to start and faster and better lubrication. I just wait until they are on sale and typically find 5L jugs for around $37.
I use syn oil in my car for obvious reasons. I wouldn't trust a dino oil at 290F and under high rpm for 45 mins. I have very little burning off of oil even with the summer filled with track days, likely due to the lower volatility that syn oil has.
i am interested to see how my coolant and oil temps stack up this summer without a condenser in front of my rad, a now much larger grill and a dual pass radiator. I would expect coolant to stay below 220F but as for the oil I'm not too sure.
It decided to snow about 50cm on Saturday and then sit at -20C for the weekend so progress on my car was slowed. With having 2 kids now I'm limited to working on the cars about 2 hrs a day on the weekend while the little ones sleep.
I ended up purchasing some new gutter guard called "Leaf It". Same design as the one from Canadian Tire but a couple $ more and it is s thicker plastic. In re did the front grill but this time in 2 separate pieced converging in the center which lead for a much stronger and flat grill. I also drilled holes and did the bottom mouth of the grill. I am actually pretty happy with the final product and like the look over the stock look.
I got around to deleting my a/c system - well, everything except for the evaporator. I'll get to that when I remove the dash this spring. I probably got rid of about 18lbs. Not much, but there is now much more space in front of the alternator which makes removal much easier as well as a wider radiator possible. I am a huge fan of uncluttered engine bays and so far mine is moving in the correct direction. I will end up selling my compressor down the road if anyone is interested just let me know. I ordered a Dayco belt from my local supplier, they don't stock non a/c belt for Corolla's so they had to order it in. I'll post up the part number when I take pictures later this week when it warms up. I was surprised how much the a/c hoses cluttered up the passenger side crash beam and all that space there.
with the bumper off and the a/c system out I noticed that there is an 8" wide gaping space behind the bumper that is normally just covered with a plastic piece to block it off. Essentially this is 8" of extra space to fit a much wider radiator as the stock one is very small. Oddly enough my 1st gen Vibe's radiator which also uses a 1.8L engine (1zz) has a 6-8" wider radiator from the factory. I will be taking some measurements tonight but it appears that the rad should fit fine with a bunch of cutting of the upper rad support. The Vibe's rad sits in front of the rad support on brackets whereas the Yaris' rad sits underneath the rad support beam.
It makes more sense to go wider with a rad than just thicker as you achieve more virgin surface area and improve cooling ability better than by going thicker. This is due to the second row receiving already used air that is warmer than ambient temps. The measurements are very close (Vibe rad about an inch shorter in height) so with some drilling of new hole in the support and the Vibe's upper and lower hoses it appears to be a good fit. The upper hose from the vibe actually appears to have better clearance with my CAI than the 1st gen rad. There are also cheap ebay dual core rads for almost the same amount of $ as the 1st gens.
I'll post back when I have more info as this would be good to know for those that want to upgrade their radiator down the road but so far everything seems like it would work. I'll post pictures in a couple days, it is just too darn cold right now to bother
I ended up purchasing some new gutter guard called "Leaf It". Same design as the one from Canadian Tire but a couple $ more and it is s thicker plastic. In re did the front grill but this time in 2 separate pieced converging in the center which lead for a much stronger and flat grill. I also drilled holes and did the bottom mouth of the grill. I am actually pretty happy with the final product and like the look over the stock look.
I got around to deleting my a/c system - well, everything except for the evaporator. I'll get to that when I remove the dash this spring. I probably got rid of about 18lbs. Not much, but there is now much more space in front of the alternator which makes removal much easier as well as a wider radiator possible. I am a huge fan of uncluttered engine bays and so far mine is moving in the correct direction. I will end up selling my compressor down the road if anyone is interested just let me know. I ordered a Dayco belt from my local supplier, they don't stock non a/c belt for Corolla's so they had to order it in. I'll post up the part number when I take pictures later this week when it warms up. I was surprised how much the a/c hoses cluttered up the passenger side crash beam and all that space there.
with the bumper off and the a/c system out I noticed that there is an 8" wide gaping space behind the bumper that is normally just covered with a plastic piece to block it off. Essentially this is 8" of extra space to fit a much wider radiator as the stock one is very small. Oddly enough my 1st gen Vibe's radiator which also uses a 1.8L engine (1zz) has a 6-8" wider radiator from the factory. I will be taking some measurements tonight but it appears that the rad should fit fine with a bunch of cutting of the upper rad support. The Vibe's rad sits in front of the rad support on brackets whereas the Yaris' rad sits underneath the rad support beam.
It makes more sense to go wider with a rad than just thicker as you achieve more virgin surface area and improve cooling ability better than by going thicker. This is due to the second row receiving already used air that is warmer than ambient temps. The measurements are very close (Vibe rad about an inch shorter in height) so with some drilling of new hole in the support and the Vibe's upper and lower hoses it appears to be a good fit. The upper hose from the vibe actually appears to have better clearance with my CAI than the 1st gen rad. There are also cheap ebay dual core rads for almost the same amount of $ as the 1st gens.
I'll post back when I have more info as this would be good to know for those that want to upgrade their radiator down the road but so far everything seems like it would work. I'll post pictures in a couple days, it is just too darn cold right now to bother
+1 on too darn cold
I'm gonna follow this rad quest... Interesting...
I'm gonna follow this rad quest... Interesting...
I'll definitely be following this. It will be good to know what rad, hoses (or mods to hoses) are needed. The hatchback has the access window for the A/C compressor that could easily be narrowed making room for a - at least - longer radiator. A larger radiator might come in handy down the road if I do performance upgrades on the 2ZR.Originally Posted by tmontague ↑
I'll post back when I have more info as this would be good to know for those that want to upgrade their radiator down the road but so far everything seems like it would work. I'll post pictures in a couple days, it is just too darn cold right now to bother
Here is the part # for the Dayco belt I used for an a/c delete:
5060358
or
6PK0910
Rock auto also lists a Continental belt, just make sure you order one that that "no a/c"
The belt I removed from the car (I cannot remember the manufacturer) which I ordered from RA when I did my swap only had about 50k km on it. It had a lot of mini cracks along the ribs, enough to warrant replacement. I've seen spread out large cracks which are fine, but this one had a lot of little ones, quite a few every inch. I also noticed that the back side of the belt in one small spot looked like the outer layer was starting the peel off the belt. I used my Gates belt wear tester to check and it had a mild to moderate amount of play meaning that the belt was moderately worn.
The new one had no play as it should. Keep this is mind as I was surprised at how worn the belt was. I'm not sure if this is due to the high constant rpm of the track days I did and the heat that comes along with it, but it was definitely worn. Take note that this belt never once slipped or squealed so it was never worn out from that, it always functioned optimally. I'll post pictures later this week
5060358
or
6PK0910
Rock auto also lists a Continental belt, just make sure you order one that that "no a/c"
The belt I removed from the car (I cannot remember the manufacturer) which I ordered from RA when I did my swap only had about 50k km on it. It had a lot of mini cracks along the ribs, enough to warrant replacement. I've seen spread out large cracks which are fine, but this one had a lot of little ones, quite a few every inch. I also noticed that the back side of the belt in one small spot looked like the outer layer was starting the peel off the belt. I used my Gates belt wear tester to check and it had a mild to moderate amount of play meaning that the belt was moderately worn.
The new one had no play as it should. Keep this is mind as I was surprised at how worn the belt was. I'm not sure if this is due to the high constant rpm of the track days I did and the heat that comes along with it, but it was definitely worn. Take note that this belt never once slipped or squealed so it was never worn out from that, it always functioned optimally. I'll post pictures later this week
I braved the cold last night when the kids were asleep and took a bunch of measurements between my Yaris and the Wife's Vibe.
The good:
The Vibe radiator will fit! The width will be snug with about an inch or two on either side, but this will also fill in the complete opening very well. The Vibe radiator is 16" in height compared to the 18" between the Yaris' rad supports. This will need to be filled with a large rad support bushing, or some hammering down on that section of the rad support to close off that gap.
The lower and upper hose from the Vibe appear to be an almost perfect fit. The thermostat neck is positioned almost identical from the 2zr and 1zz. The Vibe upper hose also appears to sneak just underneath of my CAI. The only potential issue will be the Yaris battery which may slightly rub on the edge of the hose. Some trimming of the hose at the engine side will likely fix this issue, but I also won't need to worry as I will be relocating my battery soon.
The bad:
The tricky part that will likely not work is the Vibe factory fan shroud. It is a whopping 4-5" thick from the center of the rad to the engine side. The Vibe had much more space in front of the 1zz to the rad support than the Yaris' does. You can see the Yaris fan shroud is a much slimmer 3" thick design whereas the Vibe coolant reservoir is more traditional is thickness.
The tightest spot in my engine bay to the top rad support is the passenger side where the alternator and alternator bracket is. This is the same location where the Vibe coolant reservoir sits.
The solution would be to run a Mishimoto 12" slimline fan that only has a 2.5" thickness. I can mount it right to the radiator as it is designed to be and I can put it on the driver side where there is much more clearance. I can simply wire it up the the factory wires (ground and power) so it works like it was designed to.
I can then buy a generic coolant overflow bottle and mount it on the driver side near the headlight where there is a lot of space. This is simple as I would only need to run a small rubber hose from the bottle to the filler neck on the passenger side along to top of the rad support.
This seems like the best and cheapest option to ensure a properly function system and keep the most clearance as possible to make wrenching in the future as easy and obstruction free as it can be. I don't want to have to pull the fan and rad every time I need to remove the alternator.
I don't need to run a fan shroud as the size of the new rad will be much larger then the 2zr will ever need. The only time the fan shroud is of benefit is while the car is stopped or in traffic. Even after a 45 min track session, my coolant has never had an issue coming down to 212F with the stock set up. My cololant issues were seen during the long track sessions at WOT and high rpm for most of the time. Once I got 15-20 mins into the session the coolant was 230F.
The fan shroud will technically actually reduce air flow through the rad during driving, this is why the Vibe shroud has slits in the shroud beside the fan. I saw that MWR sells a dual core rad for the Vibe for $150 and a Mishimoto fan is around $60. So under $300 Canadian for the set up is reasonable.
This will not be a simple bolt on as I will have to possibly drill new mounting holes in both rad supports (easy) and cut away some metal from the upper support to fit around the filler neck and rad (fairly easy).
For those that have a 2zr but do not track it, a factory Vibe radiator would likely be more than adequate as it is about 20%-25% larger than the 2zr radiator. There isn't really much need for a dual core unless you heavily track your car or are going boosted. As long as your thermostat is working properly there really isn't much down side to a larger radiator other than excess weight which is minimal
The good:
The Vibe radiator will fit! The width will be snug with about an inch or two on either side, but this will also fill in the complete opening very well. The Vibe radiator is 16" in height compared to the 18" between the Yaris' rad supports. This will need to be filled with a large rad support bushing, or some hammering down on that section of the rad support to close off that gap.
The lower and upper hose from the Vibe appear to be an almost perfect fit. The thermostat neck is positioned almost identical from the 2zr and 1zz. The Vibe upper hose also appears to sneak just underneath of my CAI. The only potential issue will be the Yaris battery which may slightly rub on the edge of the hose. Some trimming of the hose at the engine side will likely fix this issue, but I also won't need to worry as I will be relocating my battery soon.
The bad:
The tricky part that will likely not work is the Vibe factory fan shroud. It is a whopping 4-5" thick from the center of the rad to the engine side. The Vibe had much more space in front of the 1zz to the rad support than the Yaris' does. You can see the Yaris fan shroud is a much slimmer 3" thick design whereas the Vibe coolant reservoir is more traditional is thickness.
The tightest spot in my engine bay to the top rad support is the passenger side where the alternator and alternator bracket is. This is the same location where the Vibe coolant reservoir sits.
The solution would be to run a Mishimoto 12" slimline fan that only has a 2.5" thickness. I can mount it right to the radiator as it is designed to be and I can put it on the driver side where there is much more clearance. I can simply wire it up the the factory wires (ground and power) so it works like it was designed to.
I can then buy a generic coolant overflow bottle and mount it on the driver side near the headlight where there is a lot of space. This is simple as I would only need to run a small rubber hose from the bottle to the filler neck on the passenger side along to top of the rad support.
This seems like the best and cheapest option to ensure a properly function system and keep the most clearance as possible to make wrenching in the future as easy and obstruction free as it can be. I don't want to have to pull the fan and rad every time I need to remove the alternator.
I don't need to run a fan shroud as the size of the new rad will be much larger then the 2zr will ever need. The only time the fan shroud is of benefit is while the car is stopped or in traffic. Even after a 45 min track session, my coolant has never had an issue coming down to 212F with the stock set up. My cololant issues were seen during the long track sessions at WOT and high rpm for most of the time. Once I got 15-20 mins into the session the coolant was 230F.
The fan shroud will technically actually reduce air flow through the rad during driving, this is why the Vibe shroud has slits in the shroud beside the fan. I saw that MWR sells a dual core rad for the Vibe for $150 and a Mishimoto fan is around $60. So under $300 Canadian for the set up is reasonable.
This will not be a simple bolt on as I will have to possibly drill new mounting holes in both rad supports (easy) and cut away some metal from the upper support to fit around the filler neck and rad (fairly easy).
For those that have a 2zr but do not track it, a factory Vibe radiator would likely be more than adequate as it is about 20%-25% larger than the 2zr radiator. There isn't really much need for a dual core unless you heavily track your car or are going boosted. As long as your thermostat is working properly there really isn't much down side to a larger radiator other than excess weight which is minimal
I know the sedan has way more clearance in the engine bay behind the headlights due to the fact yours don't go 3/4 the way back to the windshield. Not sure if this is the only spot where clearances differ between HB and sedan. Just raising a highlight since most peeps following you drive hatches.
Sent from my EML-L09 using Tapatalk
Sent from my EML-L09 using Tapatalk
What year is your Vibe, Trevor?
good point, I hadn't thought of that. That being said, due to where the rad sits and the hoses run, it shouldn't prove to be an issue unless the rad support is narrower. This could be easily figured out if an LB owner just roughly measures the width of the rad supportOriginally Posted by WeeYari ↑I know the sedan has way more clearance in the engine bay behind the headlights due to the fact yours don't go 3/4 the way back to the windshield. Not sure if this is the only spot where clearances differ between HB and sedan. Just raising a highlight since most peeps following you drive hatches.
Sent from my EML-L09 using Tapatalk
it is a 1st gen '05Originally Posted by 06YarisRS ↑What year is your Vibe, Trevor?
This weekend is looking like it will be -20C, yaaaaay👎
I will probably just get around to shimming my Throttle pedal and letting it cure all weekend as I don't drive my car much all weekend. I used super glue and a small piece of plastic a couple years ago and it eventually let go. This time I plan on using some JB Weld epoxy which should work very well. The purpose of this is to remove the slack in the throttle pedal that the DBW system has. That "dead zone" essentially does not register with the ecu and does nothing to open the throttle body valve even though the pedal is slightly depressed. This won't help performance at all but it will make it easier to drive around town.
I have attached pics of my old drive belt that I removed from the car when I deleted my a/c. As you can see it is fairly worn in a few areas. If you drive your car at WOT and high rpm's a fair amount then I'd recommend checking the condition of your belt more often. After seeing this, I think I will carry an extra/old belt with me to try track just in case one ever lets go. It's an easy fix if it ever happened and it would be silly to need to pay for a tow just for something so simple.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
I will probably just get around to shimming my Throttle pedal and letting it cure all weekend as I don't drive my car much all weekend. I used super glue and a small piece of plastic a couple years ago and it eventually let go. This time I plan on using some JB Weld epoxy which should work very well. The purpose of this is to remove the slack in the throttle pedal that the DBW system has. That "dead zone" essentially does not register with the ecu and does nothing to open the throttle body valve even though the pedal is slightly depressed. This won't help performance at all but it will make it easier to drive around town.
I have attached pics of my old drive belt that I removed from the car when I deleted my a/c. As you can see it is fairly worn in a few areas. If you drive your car at WOT and high rpm's a fair amount then I'd recommend checking the condition of your belt more often. After seeing this, I think I will carry an extra/old belt with me to try track just in case one ever lets go. It's an easy fix if it ever happened and it would be silly to need to pay for a tow just for something so simple.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
good idea, cheap insurance. I changed my belt when I got my car it had 200K kms on it and started squealing. I am pretty sure it was the original, and looked a lot worse than that one. I have put another 158K on the car so may be time to grab a replacement just in case and throw it on.
I installed my new Oil Catch Can last night - bad idea, -30+C with the wind chill...
My old set up of the dual air compressor air/oil separators was effective but it was always a temporary solution until I had the funds to run a properly installed OCC. I received a gift certificate from work for xmas and I was able to apply it to Amazon.ca so I ended up with a proper catch can. Over a month later and here it is from China. I forgot to take a pic of the actual OCC but here is the set up I went with.
This can has two "grills" or perforated plates/baffles that the intake air goes through. It has a dip stick to check the level and it holds much more than my current set up does. In the really cold winter up here I ended of catching a ton of moisture/water in the can and it fills much earlier than it does in the summer. I was emptying my old set up every week or two and it was mostly water. I needed something with a proper reservoir.
I wanted to mount it lower in the engine bay so water wouldn't freeze in the lines, as well as to keep the COG low and keep it out of the way. The set up probably weighs a few pounds at the most, it is a bit heavier than I expected.
To improve the oil catching ability you need to increase the surface area of material in the can so the oil in the air can be condensed on it and pooled into the reservoir. This can actually comes apart as the baffles are two threaded cups. I placed a small amount of stainless steel wool (it gets contaminated with moisture so make sure it is stainless so it doesn't rust) between the two baffled cups which holds it in place in the air intake stream. I then ziptied a piece of a rough 3m scotch brite around the outside of the baffled cup.
The air that enters the can is forced by the design to go into the baffled cup and then out of it and then out the exhaust hose. With my current design the air will contact the first baffle, then the steel wool, then the second baffle and then the scotch brite pad. The oil will then drip into the reservoir before the air exists and enters the intake manifold behind the throttle body (constant vacuum)
On my old set up I used the steel wool in the first can and the scotch bright pad in the second. Most of the oil was caught in the first can and the second one caught mostly water. It appears that oil is easier to catch in the air than water.
To install the can mounting bracket I used two riv nuts from a cheap tool I purchased from Princess Auto. I purposefully bought the metric one as all the bolts on the Yaris are metric. Turns out the 2 mounting bolts that came with the kit fit in the second smallest riv nut size. I drilled two hole on the crash rail mount and filled it with anti seize so it doesn't rust. I then installed the riv nuts and mounted the can to that. It is surprisingly sturdy and i will definitely be using those riv nuts again, they make quick work is you need threads in thin metal or metal you can only access one side of.
My complaint with the OCC is that the mounting bracket has a silly design when the 2 bolts that actually mount to the catch can are on the side instead of the top. This makes getting an allen key onto them almost impossible depending on how you mount it. Most designs have the bolts on top so nothing is in your way. I will take a hammer and flat punch and dent the crash bar a bit so that I can access the one allen bolt. Currently one is tightened all the way and the other is still on the lose side.
I can check the dip stick very easily with where it is mounted and with a simple reach around I can unscrew and drain the reservoir. This wouldn't work well with the stock air box, but with my CAI I have a lot of room in that area. Once the battery is moved, I'll have even more space. This also shouldn't impede my future Vibe radiator install as I can just mount the fan a but more in the middle to easily clear the OCC.
Before I installed the can I put antiseize on all the threads which made a huge difference in how smooth everything threaded on/off. I also added pipe tape to the hose nipples before I tightened them down. They are not a tapered NPT type thread but a regular thread and they are not the tightest.
I'll post back later on how well the can performs, but assuming it will catch oil as well or better than my old set up, I'm impressed with it for the price. IIRC I paid about $42 CAD for it
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
My old set up of the dual air compressor air/oil separators was effective but it was always a temporary solution until I had the funds to run a properly installed OCC. I received a gift certificate from work for xmas and I was able to apply it to Amazon.ca so I ended up with a proper catch can. Over a month later and here it is from China. I forgot to take a pic of the actual OCC but here is the set up I went with.
This can has two "grills" or perforated plates/baffles that the intake air goes through. It has a dip stick to check the level and it holds much more than my current set up does. In the really cold winter up here I ended of catching a ton of moisture/water in the can and it fills much earlier than it does in the summer. I was emptying my old set up every week or two and it was mostly water. I needed something with a proper reservoir.
I wanted to mount it lower in the engine bay so water wouldn't freeze in the lines, as well as to keep the COG low and keep it out of the way. The set up probably weighs a few pounds at the most, it is a bit heavier than I expected.
To improve the oil catching ability you need to increase the surface area of material in the can so the oil in the air can be condensed on it and pooled into the reservoir. This can actually comes apart as the baffles are two threaded cups. I placed a small amount of stainless steel wool (it gets contaminated with moisture so make sure it is stainless so it doesn't rust) between the two baffled cups which holds it in place in the air intake stream. I then ziptied a piece of a rough 3m scotch brite around the outside of the baffled cup.
The air that enters the can is forced by the design to go into the baffled cup and then out of it and then out the exhaust hose. With my current design the air will contact the first baffle, then the steel wool, then the second baffle and then the scotch brite pad. The oil will then drip into the reservoir before the air exists and enters the intake manifold behind the throttle body (constant vacuum)
On my old set up I used the steel wool in the first can and the scotch bright pad in the second. Most of the oil was caught in the first can and the second one caught mostly water. It appears that oil is easier to catch in the air than water.
To install the can mounting bracket I used two riv nuts from a cheap tool I purchased from Princess Auto. I purposefully bought the metric one as all the bolts on the Yaris are metric. Turns out the 2 mounting bolts that came with the kit fit in the second smallest riv nut size. I drilled two hole on the crash rail mount and filled it with anti seize so it doesn't rust. I then installed the riv nuts and mounted the can to that. It is surprisingly sturdy and i will definitely be using those riv nuts again, they make quick work is you need threads in thin metal or metal you can only access one side of.
My complaint with the OCC is that the mounting bracket has a silly design when the 2 bolts that actually mount to the catch can are on the side instead of the top. This makes getting an allen key onto them almost impossible depending on how you mount it. Most designs have the bolts on top so nothing is in your way. I will take a hammer and flat punch and dent the crash bar a bit so that I can access the one allen bolt. Currently one is tightened all the way and the other is still on the lose side.
I can check the dip stick very easily with where it is mounted and with a simple reach around I can unscrew and drain the reservoir. This wouldn't work well with the stock air box, but with my CAI I have a lot of room in that area. Once the battery is moved, I'll have even more space. This also shouldn't impede my future Vibe radiator install as I can just mount the fan a but more in the middle to easily clear the OCC.
Before I installed the can I put antiseize on all the threads which made a huge difference in how smooth everything threaded on/off. I also added pipe tape to the hose nipples before I tightened them down. They are not a tapered NPT type thread but a regular thread and they are not the tightest.
I'll post back later on how well the can performs, but assuming it will catch oil as well or better than my old set up, I'm impressed with it for the price. IIRC I paid about $42 CAD for it
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
short update on the OCC. 3 days ago I filled the can about 1/4 full of windshield washer fluid so it wouldn't freeze. I checked the dipstick after the car drove 25km today and got close to operating temps (oil temp at 167F) and it showed full alrthough it isn't easy to read.
I remove the can to see how full it was and sure enough it was 95% full. This all within 3 days and probably 75-100km driven! It has been about -18C to -25C ambient temps here for the past 3 days but clearly the new can and the stuff I added to it are extremely effective.
I think I'll be forgoing the windshield washer fluid as I don't want to be wasting that much every week. As long as I check the can every few days and empty it then I shouldn't have to worry about it freezing and blocking the air flow. So far I'm impressed. Most of what was in the can was water but there was also a milky film on it so there was also some oil as well.
I remove the can to see how full it was and sure enough it was 95% full. This all within 3 days and probably 75-100km driven! It has been about -18C to -25C ambient temps here for the past 3 days but clearly the new can and the stuff I added to it are extremely effective.
I think I'll be forgoing the windshield washer fluid as I don't want to be wasting that much every week. As long as I check the can every few days and empty it then I shouldn't have to worry about it freezing and blocking the air flow. So far I'm impressed. Most of what was in the can was water but there was also a milky film on it so there was also some oil as well.
The OCC was a big success, it catches about 3 ounces of oil/water (smells like fuel) per week in the cold. It is much more efficient than the last set up
On another note, I bought some new track semi slicks for the upcoming season. Nankang AR1's, relatively new to NA but common in Europe. I'll do a review on them once I get some time with them. They are an 80tw rating and are a 205 50 size
Picture not included in this copy
All that's left to go for the car prep before the season is to get Vibe/matrix upper and lower radiator hoses so I can install the performance radiator and install new brake lines in all 4 corners.
I'll be running a 5w40 euro spec oil and swapping out my mt-85 redline trans fluid for mt-90 due to the warmer temps coming (hopefully soon)
I'll be doing a thread on the radiator fit when I get around to it for anyone who wants to do the swap in the future
On another note, I bought some new track semi slicks for the upcoming season. Nankang AR1's, relatively new to NA but common in Europe. I'll do a review on them once I get some time with them. They are an 80tw rating and are a 205 50 size
Picture not included in this copy
All that's left to go for the car prep before the season is to get Vibe/matrix upper and lower radiator hoses so I can install the performance radiator and install new brake lines in all 4 corners.
I'll be running a 5w40 euro spec oil and swapping out my mt-85 redline trans fluid for mt-90 due to the warmer temps coming (hopefully soon)
I'll be doing a thread on the radiator fit when I get around to it for anyone who wants to do the swap in the future
This! I swear my oil had a weird fuel smell, but the Blackstone Labs analysis didn't show anything notable in the sample - seems like another 'glad I'm not the only one' oddity of the 2ZR. lolOriginally Posted by tmontague ↑The OCC was a big success, it catches about 3 ounces of oil/water (smells like fuel) per week in the cold. It is much more efficient than the last set up
On another note, I bought some new track semi slicks for the upcoming season. Nankang AR1's, relatively new to NA but common in Europe. I'll do a review on them once I get some time with them. They are an 80tw rating and are a 205 50 size
...
Interested to hear how you find the Nankangs. With the influx of more cheap tires it seems some are junk, and some are actually pretty decent for the price point.
Awesome as always. Looking forward to checking it out sometime this summer.
-- Adam
My last oil sample I sent in to Blackstone from the summer stink like fuel. Came back negative on fuel content.
I've read that used oil commonly smells like fuel, I definitely wouldn't be worried.
I'm excited to try these tires out, I'm curious how much my confidence goes up with a more controlable and feedback friendly tire
I've read that used oil commonly smells like fuel, I definitely wouldn't be worried.
I'm excited to try these tires out, I'm curious how much my confidence goes up with a more controlable and feedback friendly tire
Definitely sounds like I should be considering a catch can myself.
You must be itching to try out those new tires.
You must be itching to try out those new tires.
My old flooded lead acid battery from CT went to crap so I decided on a pricier but more reliable and safer (non spillable since it is now in the cabin) AGM battery. This thing is a beats, smaller in diuameter than the group 36 it replaced but has 655 CCA's and 50 Ah (100 reserve). However, in the rush to grab a new battery I didn't really think of the weight. The AGM battery although smaller, is just as heavy as the old one and probably weighs around 35-45lbs!
I ended up ordering an AGM motorcycle battery online which weighs a claimed 11lbs (probably closer to 12). It is rated at 270 CCA and has 18Ah (36 reserve). This cranks the car barely noticeably slower in 0 degree C temps but has no problem The issue with small batteries is their lack of reserve capacity. This can lead to the battery draining down after a couple days, especially in the cold. I installed it fully charged reading just over 13V and after about 24 hours it was at 12.54V which is about 80% charged. It turned over the engine this morning in -10C temps albeit a bit slower than it typically does.
I bought a small trickle charger/maintainer that I will hook up in the winter if I am going to have the car sit longer than 2 nights. I can leave the maintainer in my car and just hook up an extension cord as needed.
These batteries typically die an early life because people drain them and then jump them. Anytime a battery gets fully drained you can say good bye to it's useful life. AGM's can tolerate lower discharge amounts, but they srtill are not immune to this happening. Best practice is to keep a charger on it if it won't be used for a while. These batteries are also sensitive to heat but this won't be a problem as I have mine in my cabin.
All in all I just lost about 25-35lbs out of my car for very little money ($50 USD shipped with taxes) I had to flip the battery tie down bracket so I had usable threads on the rods but it is holding very tightly and won't budge. I never needed any battery post adaptors as I just unbolted my oem post terminals from my ground and pwer wires and bolted those directly to the motorcycle style terminals with a washer. Simple and effective.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
up next is my Vibe radiator install...easter long weekend is looking like a decent time to do it
I ended up ordering an AGM motorcycle battery online which weighs a claimed 11lbs (probably closer to 12). It is rated at 270 CCA and has 18Ah (36 reserve). This cranks the car barely noticeably slower in 0 degree C temps but has no problem The issue with small batteries is their lack of reserve capacity. This can lead to the battery draining down after a couple days, especially in the cold. I installed it fully charged reading just over 13V and after about 24 hours it was at 12.54V which is about 80% charged. It turned over the engine this morning in -10C temps albeit a bit slower than it typically does.
I bought a small trickle charger/maintainer that I will hook up in the winter if I am going to have the car sit longer than 2 nights. I can leave the maintainer in my car and just hook up an extension cord as needed.
These batteries typically die an early life because people drain them and then jump them. Anytime a battery gets fully drained you can say good bye to it's useful life. AGM's can tolerate lower discharge amounts, but they srtill are not immune to this happening. Best practice is to keep a charger on it if it won't be used for a while. These batteries are also sensitive to heat but this won't be a problem as I have mine in my cabin.
All in all I just lost about 25-35lbs out of my car for very little money ($50 USD shipped with taxes) I had to flip the battery tie down bracket so I had usable threads on the rods but it is holding very tightly and won't budge. I never needed any battery post adaptors as I just unbolted my oem post terminals from my ground and pwer wires and bolted those directly to the motorcycle style terminals with a washer. Simple and effective.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
up next is my Vibe radiator install...easter long weekend is looking like a decent time to do it
It's so cute.
You need a smaller battery box now!
Swapped out my 0w30 Mobil 1 for some Quaker State full syn 0w20. I will post up any difference I see in oil pressure or temps. Based on 540Rat's testing on his blog I opted for this oil due to its very impressive psi rating. The only other oil better than it was Amsoil and I picked up QSUD for $31 for 5L on sale and my Amsoil price of 0w20 signature is much higher than that.
I also am trying out a larger filter this time around, much higher capacity, brings the 2zr from 4.4 L to some where just shy of 5L so probably an extra 200-400ml capacity. The filter is currently a Fram Ultra Synthetic and is spec'd on many of Toyota's v6 engines as well as a 2002 2zz Celica GTS. The only difference between them is the larger filter specs a slightly lower bypass valve PSI of 12 vs 14PSI for the regular filter. The should be a moot issue for me.
Regular oem direct replacement
Picture not included in this copy
larger capacity filter
Picture not included in this copy
the larger capacity is larger and barely clears the engine block. It leaves about a 1/4" between the filter housing and block.
***take note - keeping the throttle pedal fully depressed when starting the 2zr does not put it into clear flood mode and cut off fuel. It leads to your bouncing off the rev limited at start up***
learn from my mistake...good thing I fully fill/prime the oil filter during install.
All that is left is to make a new rear brake line due to rust and replace the front rubber lines and bleed the system. Then off to the track!
I also am trying out a larger filter this time around, much higher capacity, brings the 2zr from 4.4 L to some where just shy of 5L so probably an extra 200-400ml capacity. The filter is currently a Fram Ultra Synthetic and is spec'd on many of Toyota's v6 engines as well as a 2002 2zz Celica GTS. The only difference between them is the larger filter specs a slightly lower bypass valve PSI of 12 vs 14PSI for the regular filter. The should be a moot issue for me.
Regular oem direct replacement
Picture not included in this copy
larger capacity filter
Picture not included in this copy
the larger capacity is larger and barely clears the engine block. It leaves about a 1/4" between the filter housing and block.
***take note - keeping the throttle pedal fully depressed when starting the 2zr does not put it into clear flood mode and cut off fuel. It leads to your bouncing off the rev limited at start up***
learn from my mistake...good thing I fully fill/prime the oil filter during install.
All that is left is to make a new rear brake line due to rust and replace the front rubber lines and bleed the system. Then off to the track!
Picture not included in this copy
I drained my Redline MT-85 after about 6k km on it throughout the winter. It shifted very well in the deep cold of our winter but I noticed the shifting degraded slightly as the temps stayed above 0*C. I always planned to run MT-90 during the track season due to higher temps.
When I drained the MT-85 I noticed what I thought was an alarming amount of gold specs suspended throughout the trans fluid. No large chunks, all specs and the magnet on my Mishimoto plug was very clean. My guess is the synchros, but I only ever have a 3rd gear synchro issue when I do really quick shifts, or when I'm at the track under hard cornering.
I'll see how the MT-90 fares, but I seriously contemplating trying to find a GL-4 75w90 (or 80w90 at the very least) conventional trans fluid. I'll just change it out more often due to high track temps, but I'm starting to question the MT-90 in out old Yaris manual transmissions. I'm trying to balance good shifting with a clutch type diff all housed in the same box. The MT-90 did a great job for this and is easy for me to find.
I'll post any updates as I figure this out. It's possible that the fluid had nothing to do with this but I'm going to keep an eye on it.
Tomorrow I'm going to plug away at the last thing I need to do which is replace the 4 rubber brake lines. The rears are seized so it looks like I'll be replacing the whole main lines that run to the rear with some NiCop lines I'll be bending myself. That should be a learning curve
I drained my Redline MT-85 after about 6k km on it throughout the winter. It shifted very well in the deep cold of our winter but I noticed the shifting degraded slightly as the temps stayed above 0*C. I always planned to run MT-90 during the track season due to higher temps.
When I drained the MT-85 I noticed what I thought was an alarming amount of gold specs suspended throughout the trans fluid. No large chunks, all specs and the magnet on my Mishimoto plug was very clean. My guess is the synchros, but I only ever have a 3rd gear synchro issue when I do really quick shifts, or when I'm at the track under hard cornering.
I'll see how the MT-90 fares, but I seriously contemplating trying to find a GL-4 75w90 (or 80w90 at the very least) conventional trans fluid. I'll just change it out more often due to high track temps, but I'm starting to question the MT-90 in out old Yaris manual transmissions. I'm trying to balance good shifting with a clutch type diff all housed in the same box. The MT-90 did a great job for this and is easy for me to find.
I'll post any updates as I figure this out. It's possible that the fluid had nothing to do with this but I'm going to keep an eye on it.
Tomorrow I'm going to plug away at the last thing I need to do which is replace the 4 rubber brake lines. The rears are seized so it looks like I'll be replacing the whole main lines that run to the rear with some NiCop lines I'll be bending myself. That should be a learning curve
Soft brake lines in the front replaced and hard lines in the rear replaced with NiCopp line. I have rear soft lines but they are seized to the line that travels under the car up to the front of the car. I didn't have time to use some heat and vice grips to try and free it up so I just soaked it in penetrating fluid. My line wrench was starting to slip on the nut and it has a lot of play on it so I just stopped.
Bending my own lines went fairly well but it was a learning experience for sure. NiCopp is crazy easy to use as it is very flexible and I ended up making most of the bends with my hands. I have a line bender but the bends are not a super tight radius like the OE lines are so my hands did a better job. I practised about 10 times making double flares the day before and it went ok. The generic tool is fine for a DIY'er but you have to be super careful that it is on the line perfectly straight or you have to re do it.
NiCopp never rusts like the original OE lines so it give you some piece of mine. Pro tip: remove the OE line from the car and then put it on a bench and bend your new line following the old line. Do not try and use a coat hanger that you bent to try and copy it. This may work for simple bent lines but the rears in the Yaris have so odd shape bends and angles and it definitely did not work nearly as fast as just following the original line.
Pro tip #2: Place plastic wrap or half a ziplock bag under the brake reservoir cap. This blocks off the vent in the cap and creates negative pressure as brake fluid drips out of your open lines. This really slow down the leaking of the line quite a bit. They still drip but much much slower so you are not having to constantly fill up the reservoir to avoid bench bleeding your M/C.
I finally got to use my new Toyota specific properly sealing reservoir cap that attaches to my pressure bleeder. Seals perfectly fine and held 20psi with no leaks. Was able to completely flush my fluid in all 4 brake and my slave cylinder in under 15 mins by myself - seriously this tool in unreal with the proper cap.
One of the original rear lines - it started to rust on the metal that is near the nut as it isn't coated in poly
Picture not included in this copy
Line #1
Picture not included in this copy
Line #2
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
I also made a proper bracket for all of my power cables that attach to my main power line in the engine bay. Previous to this the fusible link and all the wires were sort of just hovering in space "supported" by the wires themselves. As the temps warmed up the cable became softer and it started drooping. I didn't want the wires to becomes damaged due to bumps and track driving.
The bracket was a simple piece of aluminium and I used a preexisting threaded hole that is on the top of the trans mount meant for the factory battery tray. Because you cannot directly attach the power wires to a piece of metal touching the grounded chassis, I had previously ordered an insulated threaded post from Amazon. I used self tapping screws to mount the insulated post the the bracket and then mounted the whole fusible link to the insulated post. I wanted to keep the main fuses just in case I do an electrical no no and it will save me from a blown ECU and other things. It is good to have that thing still around.
Picture not included in this copy
Picture not included in this copy
Bending my own lines went fairly well but it was a learning experience for sure. NiCopp is crazy easy to use as it is very flexible and I ended up making most of the bends with my hands. I have a line bender but the bends are not a super tight radius like the OE lines are so my hands did a better job. I practised about 10 times making double flares the day before and it went ok. The generic tool is fine for a DIY'er but you have to be super careful that it is on the line perfectly straight or you have to re do it.
NiCopp never rusts like the original OE lines so it give you some piece of mine. Pro tip: remove the OE line from the car and then put it on a bench and bend your new line following the old line. Do not try and use a coat hanger that you bent to try and copy it. This may work for simple bent lines but the rears in the Yaris have so odd shape bends and angles and it definitely did not work nearly as fast as just following the original line.
Pro tip #2: Place plastic wrap or half a ziplock bag under the brake reservoir cap. This blocks off the vent in the cap and creates negative pressure as brake fluid drips out of your open lines. This really slow down the leaking of the line quite a bit. They still drip but much much slower so you are not having to constantly fill up the reservoir to avoid bench bleeding your M/C.
I finally got to use my new Toyota specific properly sealing reservoir cap that attaches to my pressure bleeder. Seals perfectly fine and held 20psi with no leaks. Was able to completely flush my fluid in all 4 brake and my slave cylinder in under 15 mins by myself - seriously this tool in unreal with the proper cap.
One of the original rear lines - it started to rust on the metal that is near the nut as it isn't coated in poly
Picture not included in this copy
Line #1
Picture not included in this copy
Line #2
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
I also made a proper bracket for all of my power cables that attach to my main power line in the engine bay. Previous to this the fusible link and all the wires were sort of just hovering in space "supported" by the wires themselves. As the temps warmed up the cable became softer and it started drooping. I didn't want the wires to becomes damaged due to bumps and track driving.
The bracket was a simple piece of aluminium and I used a preexisting threaded hole that is on the top of the trans mount meant for the factory battery tray. Because you cannot directly attach the power wires to a piece of metal touching the grounded chassis, I had previously ordered an insulated threaded post from Amazon. I used self tapping screws to mount the insulated post the the bracket and then mounted the whole fusible link to the insulated post. I wanted to keep the main fuses just in case I do an electrical no no and it will save me from a blown ECU and other things. It is good to have that thing still around.
Picture not included in this copy
Picture not included in this copy
Continued on my quest this weekend to have my car fully track ready. Fab'd up a small bracket to fix my now completely unsupported DC Sports CAI. The CAI is meant for a Scion xD and it will work in our Yaris' however it forces the intake filter against the left headlight. This leads to the head light point upwards (can be adjusted so you are not blinding others) as well as puts stress on the rubber mounting bracket that comes with the intake.
My bracket ended up breaking at the rubber damper a few months ago and was only supported by the silicone coupling at the throttle body. This needed to be dealt with properly as the stress and bumps at the track could lead to a vacuum leak.
I took some flat metal stock I previously had lying around from my radiator install and bent a z shaped bracket to replace the broken one. I tapped the bracket on the end closest to the headlight so I didn't have to install as nut as well.
Cheap and dirty but it works very well and the intake now has no movement at all. I also was able to reposition the intake so the filter not is not putting pressure against the headlight housing and they are completely free of one another. I had to run the bumper wiring loom above the intake a opposed to its stock location running below it but this was to avoid contact and potential rubbing away of the insulation on the wiring harness.
Picture not included in this copy
Picture not included in this copy
I will be getting a corner balance and alignment done and then everything is a go!
My bracket ended up breaking at the rubber damper a few months ago and was only supported by the silicone coupling at the throttle body. This needed to be dealt with properly as the stress and bumps at the track could lead to a vacuum leak.
I took some flat metal stock I previously had lying around from my radiator install and bent a z shaped bracket to replace the broken one. I tapped the bracket on the end closest to the headlight so I didn't have to install as nut as well.
Cheap and dirty but it works very well and the intake now has no movement at all. I also was able to reposition the intake so the filter not is not putting pressure against the headlight housing and they are completely free of one another. I had to run the bumper wiring loom above the intake a opposed to its stock location running below it but this was to avoid contact and potential rubbing away of the insulation on the wiring harness.
Picture not included in this copy
Picture not included in this copy
I will be getting a corner balance and alignment done and then everything is a go!
Haha, very cool and creative. One thing I've noticed is that virtually every adaptation/mod I have done related to my turbo build has been do-able because of the way the Yaris is designed. I always seem to have just enough space (with slight modifications), always have some convenient place to anchor stuff too etc. I can definitely say that I got lucky a few times.
Do you have any concerns about vibrations causing cracking in the plastic headlight body? The headlights do seem quite robust, however. I do like where your filter is placed. I'd have mine there too if it weren't already occupied by the charge piping.
Do you have any concerns about vibrations causing cracking in the plastic headlight body? The headlights do seem quite robust, however. I do like where your filter is placed. I'd have mine there too if it weren't already occupied by the charge piping.
I agree, for such a small engine bay/front end, there is a decent enough amount of room in there. Have you ever seen the engine bay of a Mini S, they give me anxiety just looking at them!Originally Posted by 06YarisRS ↑Haha, very cool and creative. One thing I've noticed is that virtually every adaptation/mod I have done related to my turbo build has been do-able because of the way the Yaris is designed. I always seem to have just enough space (with slight modifications), always have some convenient place to anchor stuff too etc. I can definitely say that I got lucky a few times.
Do you have any concerns about vibrations causing cracking in the plastic headlight body? The headlights do seem quite robust, however. I do like where your filter is placed. I'd have mine there too if it weren't already occupied by the charge piping.
The intake and filter is no longer touching the headlight housing since I installed my bracket. There should be any contact even with bumps so there should be no issue of cracking. The original bracket supplied by DC is rubber dampened but my bracket is not, potentially my bracket could crack but it seems very stable and the intake is not overly heavy so it should be fine
Actually, yes, I did have the chance to peek into the engine bay of a Cooper S. One of my colleagues bought a 2014 recently. Yep, pretty tight in there for sure. My bay, by comparison, looks quite airy. It makes me feel a touch better about engine bay temps. His Cooper is the Countryman AWD, I believe. We went for a little spin and he was kind enough to let me drive. To be honest, I was expecting a bit more uumph. I'm pretty sure my 3.5L powered Sedona minivan would walk all over it. I expect that the regular, lighter Cooper S FWD would be more impressive.Originally Posted by tmontague ↑I agree, for such a small engine bay/front end, there is a decent enough amount of room in there. Have you ever seen the engine bay of a Mini S, they give me anxiety just looking at them!
The intake and filter is no longer touching the headlight housing since I installed my bracket. There should be any contact even with bumps so there should be no issue of cracking. The original bracket supplied by DC is rubber dampened but my bracket is not, potentially my bracket could crack but it seems very stable and the intake is not overly heavy so it should be fine
I didn't realize that your mount was not on the headlight housing. Sounds like you've got a great solution there.
The first gen Mini S's used to ride on the bump stops they were so harsh - handles like go carts but tough to daily. The second gen's they smoothed it out quite a bit and made it much more refined. They are definitely a blast to drive but as usual they suffer from carbon build up on the intake valves badly and trying to do anything in that engine bay is a disaster.Originally Posted by 06YarisRS ↑Actually, yes, I did have the chance to peek into the engine bay of a Cooper S. One of my colleagues bought a 2014 recently. Yep, pretty tight in there for sure. My bay, by comparison, looks quite airy. It makes me feel a touch better about engine bay temps. His Cooper is the Countryman AWD, I believe. We went for a little spin and he was kind enough to let me drive. To be honest, I was expecting a bit more uumph. I'm pretty sure my 3.5L powered Sedona minivan would walk all over it. I expect that the regular, lighter Cooper S FWD would be more impressive.
I didn't realize that your mount was not on the headlight housing. Sounds like you've got a great solution there.
The intake mounts to a bolt hole with a bolt that grounds the headlight harness just in front of the headlight. That is where the original DC intake mount bolted to
Interesting. Yeah, I can't see the majority of the consumers liking a harsh ride regardless of how well it handled. I guess the manufacturers feel that the public is willing to sacrafice handling for a more tempered ride. I too can say that I appreciate a nice balance between handling and a smooth/comfortable ride.Originally Posted by tmontague ↑The first gen Mini S's used to ride on the bump stops they were so harsh - handles like go carts but tough to daily. The second gen's they smoothed it out quite a bit and made it much more refined. They are definitely a blast to drive but as usual they suffer from carbon build up on the intake valves badly and trying to do anything in that engine bay is a disaster.
The intake mounts to a bolt hole with a bolt that grounds the headlight harness just in front of the headlight. That is where the original DC intake mount bolted to
I'm guessing that they are DI if they are suffering the intake coking. And, yes, they''re pretty cramped in the engine bay from what I've seen.
Sounds like your intake is 'track-ready' now. We plan to be in Toronto again this summer, though haven't set hard dates. Maybe it will correspond with one of your track days. I bet my son would love to see that, haha.
That would be great to meet up at the track, we should try and coordinate somethingOriginally Posted by 06YarisRS ↑Interesting. Yeah, I can't see the majority of the consumers liking a harsh ride regardless of how well it handled. I guess the manufacturers feel that the public is willing to sacrafice handling for a more tempered ride. I too can say that I appreciate a nice balance between handling and a smooth/comfortable ride.
I'm guessing that they are DI if they are suffering the intake coking. And, yes, they''re pretty cramped in the engine bay from what I've seen.
Sounds like your intake is 'track-ready' now. We plan to be in Toronto again this summer, though haven't set hard dates. Maybe it will correspond with one of your track days. I bet my son would love to see that, haha.
Yup, the mini's are DI and have some serious intake valve issues, my in-laws have had a first and second gen mini S so that is why I've been able to drive both.
I agree with you on the handling for a DD, too stiff and it becomes no fun every day. For a track car on the other hand, it will drive pretty rough on public roads if it is set up properly for the track. I am still blown away how stable and flat my car is under severe cornering. It also drives fairly rough and gets taxing being a DDer
Decided to pull my coil packs today and inspect for oil leakage and everything came up clean. I have about 50,000km on the engine since I installed it and I changed the valve cover gasket before I put it in.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
The reason I decided to look into this is that my '05 Vibe developed a consistent misfire in cylinder 3. I figured it was a bad coil but when I went to pull the coil to swap it to another cylinder to see if the misfire moved, I realized the spark plug hole of cylinder 3 was full of oil almost above the spark plug! The other spark plug holes has oil in them but not nearly as bad. I had replaced the valve cover gasket when we bought the car used and it only has about 55,000km on the gasket. It was a brand name gasket not some ebay cheapie.
I put in a new valve cover gasket and replace the plugs as they were badly fouled with white crud. I fired up the engine and it was misfiring this time in cylinder 1. I replace the coil and it now runs fine. I am blown away that a quality valve cover gasket went bad at only 55,000km. I'm not sure if it is a coincidence and the coil went bad around the same time the valve cover gasket went or if the bad gasket led to the coil going bad.
Either way I would check your spark plug hole periodically, luckily this happened one week before heading on a long family trip to the cottage and I was able to diagnose and fix it before. The 2zr has a different design of gasket around the spark plug hole and it should last longer but the 1nz has the same design as the 1zz engine in my Vibe. The gaskwet typically fails externally which shows up as an oil staining the top of the head, but it can fail internally and be fine externally, this may save you a bad day.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
The reason I decided to look into this is that my '05 Vibe developed a consistent misfire in cylinder 3. I figured it was a bad coil but when I went to pull the coil to swap it to another cylinder to see if the misfire moved, I realized the spark plug hole of cylinder 3 was full of oil almost above the spark plug! The other spark plug holes has oil in them but not nearly as bad. I had replaced the valve cover gasket when we bought the car used and it only has about 55,000km on the gasket. It was a brand name gasket not some ebay cheapie.
I put in a new valve cover gasket and replace the plugs as they were badly fouled with white crud. I fired up the engine and it was misfiring this time in cylinder 1. I replace the coil and it now runs fine. I am blown away that a quality valve cover gasket went bad at only 55,000km. I'm not sure if it is a coincidence and the coil went bad around the same time the valve cover gasket went or if the bad gasket led to the coil going bad.
Either way I would check your spark plug hole periodically, luckily this happened one week before heading on a long family trip to the cottage and I was able to diagnose and fix it before. The 2zr has a different design of gasket around the spark plug hole and it should last longer but the 1nz has the same design as the 1zz engine in my Vibe. The gaskwet typically fails externally which shows up as an oil staining the top of the head, but it can fail internally and be fine externally, this may save you a bad day.
Great tip! You're learning so much about these engines/drivetrains etc that you should publish your own "How To" maintenance/repair manual.
Lol ya no kidding! I just try to post up as much info as I can so others can learn from my experiences. Always learning new things on these carsOriginally Posted by 06YarisRS ↑Great tip! You're learning so much about these engines/drivetrains etc that you should publish your own "How To" maintenance/repair manual.
I have booked a corner balance and alignment for the first week in June. I won't be heading to the track until then as I want everything well balanced for I start pushing the car. I am planning on going with 1/8th" total toe out in the rear and the front. This allows the car to have some sharp turn in in the front but yet the rear will still kick out a bit which aids in cornering.
Something I've always been amazed by is when you are watching pro drivers in a chicane and they aren't even steering the car as the rear end comes around just enough to point the car where it needs to go. This alignment will help with that with the negative being the wear on the inside of the tires. This is how I had my car set up last season and the turn in was spot on and I was able to control the rear end with changing the dampening on my coilovers. I ruined the alignment slightly when I had to replace worn ball joints so it needs to be re done. I have also removed a handful of weight form the car so a corner balance is in order.
I am curious as to how much my car weighs now, I'd be surprised if it wasn't around 100lbs lighter. I'll post the results here once I get it done.
I also want to build a radiator duct shroud before my first track day as the air can go underneath the car as it sits right now once it enters the lower grill. I plan to riv nut it into place on the lower rad support so it can be removed when needed
Something I've always been amazed by is when you are watching pro drivers in a chicane and they aren't even steering the car as the rear end comes around just enough to point the car where it needs to go. This alignment will help with that with the negative being the wear on the inside of the tires. This is how I had my car set up last season and the turn in was spot on and I was able to control the rear end with changing the dampening on my coilovers. I ruined the alignment slightly when I had to replace worn ball joints so it needs to be re done. I have also removed a handful of weight form the car so a corner balance is in order.
I am curious as to how much my car weighs now, I'd be surprised if it wasn't around 100lbs lighter. I'll post the results here once I get it done.
I also want to build a radiator duct shroud before my first track day as the air can go underneath the car as it sits right now once it enters the lower grill. I plan to riv nut it into place on the lower rad support so it can be removed when needed
I have my first track day of the season this Friday evening so I spent way too much time last night and early morning driveway fabrication aluminum sheet metal into a proper duct for my lower grill.
A few months ago I got tires of having to remove zip ties and re ziptie the lower bumper tray back to my bumper every time I wanted to remove the bumper. To get around this, I ziptied the tray to the lower rad support. This way to bumper comes on and off very easy.
I was left with an air gap where air can enter my lower grill anbd slip underneath the radiator and under the car. This isn't ideal from a cooling point of view which I really wasn't too worried about as my cooling capacity is now enormous for my engine set up with my Vibe radiator. I was more concerned with creating front end lift on high speed corner due to the air flow.
This ducting now forces the air from the lower grill right into the radiator with no other place it can go. I wrapped the sharp edges in foam insulation tape and used some thicker foam tape in any holes I had so there are now minimal air gaps.
I likely can now block off my whole upper grill to improve aerodynamics as I doubt I need it, but I plan to leave it for now and see how everything works. I will eventually do aero work on my car once it can sit in a garage a a dedicated track car.
I did not do any ducting to the top portion of the rad I only did the bottom and the sides. There is an OEM black plastic piece on the top of the rad that does some ducting to a certain degree and for now I'll leave that as is. Everything fits very well with the front bumper installed and is very secure thanks to a liberal use of riv nuts.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
A few months ago I got tires of having to remove zip ties and re ziptie the lower bumper tray back to my bumper every time I wanted to remove the bumper. To get around this, I ziptied the tray to the lower rad support. This way to bumper comes on and off very easy.
I was left with an air gap where air can enter my lower grill anbd slip underneath the radiator and under the car. This isn't ideal from a cooling point of view which I really wasn't too worried about as my cooling capacity is now enormous for my engine set up with my Vibe radiator. I was more concerned with creating front end lift on high speed corner due to the air flow.
This ducting now forces the air from the lower grill right into the radiator with no other place it can go. I wrapped the sharp edges in foam insulation tape and used some thicker foam tape in any holes I had so there are now minimal air gaps.
I likely can now block off my whole upper grill to improve aerodynamics as I doubt I need it, but I plan to leave it for now and see how everything works. I will eventually do aero work on my car once it can sit in a garage a a dedicated track car.
I did not do any ducting to the top portion of the rad I only did the bottom and the sides. There is an OEM black plastic piece on the top of the rad that does some ducting to a certain degree and for now I'll leave that as is. Everything fits very well with the front bumper installed and is very secure thanks to a liberal use of riv nuts.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Here is my updated alignment, slight toe out in front and slight toe in in the rear.
the car is down about 150 lbs (+/- 10lbs in fuel) from last year with everything I have removed. I unfortunately forgot to take a picture of the corner balance scales but I am very impressed with the weight loss of the car. This should make for an even more fun chassis in the corners.
Here is my updated alignment, slight toe out in front and slight toe in in the rear.
the car is down about 150 lbs (+/- 10lbs in fuel) from last year with everything I have removed. I unfortunately forgot to take a picture of the corner balance scales but I am very impressed with the weight loss of the car. This should make for an even more fun chassis in the corners.
Looking forward to your thoughts after the next track session.
for sure, I'm looking forward to seeing the differences compared to last yearOriginally Posted by ern-diz ↑Looking forward to your thoughts after the next track session.
I spent some time yesterday trying to improve airflow in the front wheel wells. I added some venting to get fresh air into the wheel well to aid in brake cooling as well as venting the wheel well via the front quarter panel.
To vent the front quarter panel I had to remove the panel and cut out some supporting metal which was right in the way of blocking the air flow. i then reinstalled the panel minus the one mounting tab that i had removed and then used a pry bar wrapped in a thick towel to manually bend it out.
The end result is a functional gap that allows the high pressure air in the wheel well to escape beside the front door.
Picture not included in this copy
Picture not included in this copy
I also cut air flow hole in the front fender cover as well as in my fog light shroud. This isn't going to be as effective as actual ducting, but it is much easier to do without having to route tubes in the area. The Yaris is a light car and not overly hard on brakes so this should at least allow fresh cooler air to be introduced into that area. I had previously pried back the dust shield so that it can force air to the rotor instead of block it and the new air holes should compliment this nicely.
Picture not included in this copy
To vent the front quarter panel I had to remove the panel and cut out some supporting metal which was right in the way of blocking the air flow. i then reinstalled the panel minus the one mounting tab that i had removed and then used a pry bar wrapped in a thick towel to manually bend it out.
The end result is a functional gap that allows the high pressure air in the wheel well to escape beside the front door.
Picture not included in this copy
Picture not included in this copy
I also cut air flow hole in the front fender cover as well as in my fog light shroud. This isn't going to be as effective as actual ducting, but it is much easier to do without having to route tubes in the area. The Yaris is a light car and not overly hard on brakes so this should at least allow fresh cooler air to be introduced into that area. I had previously pried back the dust shield so that it can force air to the rotor instead of block it and the new air holes should compliment this nicely.
Picture not included in this copy