Yarisworld Archive

Micro Image Intake Manifold thread

467 posts · 153,219 views · page 5 of 10

Replies continued

tooterLos Angeles · Jan 26, 2013#201
Originally Posted by 1.5 ↑
If I remember when I read the dyno graph it was around 2700-5500 through pretty much the entire middle of the powerband
Ok... I see the 7 foot pounds of torque, and almost 5 horsepower... 🙂

Picture not included in this copy

...and hoping that Garm will post some pictures.
1.5Tampa · Jan 26, 2013#202
I've already got I/h/e so hopefully this will add even more plus I have a 1zz TB coming
4/20 NEVER FORGETPortland, OR · Jan 26, 2013#203
Where da picz at yo??? I want to see these shiny manifolds!

I got in touch with the shop and have one on order. I don't think I got in on the first batch but Jeff said I would be in on the next manifolds you get in. I'm excited to get it!
tooterLos Angeles · Jan 27, 2013#204
Originally Posted by 4/20 NEVER FORGET ↑
Where da picz at yo??? I want to see these shiny manifolds!
Same here. 🙂
Do they actually have any yet?
Checked the MI store, no pics, no listing.
3cyltrboOttawa · Feb 1, 2013#205
Have Money = yes

Have aftermarket intake manifold = no

please help

?????

Will
Jeff@MicroImageSFV, CA · Feb 1, 2013#208
Thanks Tooter, but the picture you posted is not the final design, must be one of the prototype pics we posted earlier. The pictures on our site are of the final product:

Picture not included in this copy

Picture not included in this copy
cali yarisThread starterCanoga Park, CA · Feb 1, 2013#209
Sorry guys, I was out of town for a week, and they came in while I was away. 😢
But yeah, we have a few in stock and a steady stream coming from the welder now, so we are good to go.

Note the 1ZZ compatible flange (also works with your stock throttle body). Someone use that, please! 😁

Here is the link and new pic of the first production piece:
http://shop.microimageonline.com/Mic...takemani-Y.htm
3cyltrboOttawa · Feb 1, 2013#210
Group Buy ?

Pictures installed on a car?

massive discounts for someone with all your other products on their car?

🎉
cali yarisThread starterCanoga Park, CA · Feb 1, 2013#211
No, Yes, No. I'll post up some installed pics today.
tooterLos Angeles · Feb 1, 2013#212
Originally Posted by Jeff@MicroImage ↑
Thanks Tooter, but the picture you posted is not the final design, must be one of the prototype pics we posted earlier. The pictures on our site are of the final product:

Picture not included in this copy

Picture not included in this copy
Yeah, I found it with a Google image search because I was unable to copy the ones off your website. 😉

Here's a Google image of your manifold installed from the YouTube video.
Picture not included in this copy

By the way, I just sold my first tooter yesterday on ebay. Did I beat your first sale? 😉
1.5Tampa · Feb 1, 2013#213
so nice ^^^
cali yarisThread starterCanoga Park, CA · Feb 1, 2013#214
By the way, I just sold my first tooter yesterday on ebay. Did I beat your first sale?
No, but it was very close. 🙂
GolddeenohColumbia, SC · Feb 1, 2013#215
now if you just sold it as a performance kit with a 1zz throttle body and a set of 1zz injectors. does the 1zz throttle body directly connect in place of the 1nz-fe throttle body?
1.5Tampa · Feb 1, 2013#216
I heard a rumor that MI was planning something like that but dont know if there is/was any truth to it

The manifold was bored for the 1zz opening and the 1nz or 1zz have the same bolt pattern so yes you can swap them

-per Jeff
tooterLos Angeles · Feb 1, 2013#217
Originally Posted by cali yaris ↑
No, but it was very close. 🙂
Yeah, it was neck in neck right down to a photo finish. 😆

Congratulations on producing a really fine product, Garm. 👍
tooterLos Angeles · Feb 1, 2013#218
Originally Posted by 1.5 ↑
I heard a rumor that MI was planning something like that but dont know if there is/was any truth to it

The manifold was bored for the 1zz opening and the 1nz or 1zz have the same bolt pattern so yes you can swap them

-per Jeff
I can't for someone to actually run a 1ZZ on a MI manifold and dyno it. They're a significant improvement over the 1NZ throttle body... especially in driveability. I love mine. 🙂
1.5Tampa · Feb 1, 2013#219
Originally Posted by tooter ↑
I can't for someone to actually run a 1ZZ on a MI manifold and dyno it. They're a significant improvement over the 1NZ throttle body... especially in driveability. I love mine. 🙂
That will be me lol I just bought the 1zz tb like a few days ago specifically to add it to this manifold. I have the big 3 bolt ons as well so I think I will be seeing really nice gains
suckerfaceMilwaukee, WI · Feb 1, 2013#220
Originally Posted by 1.5 ↑
That will be me lol I just bought the 1zz tb like a few days ago specifically to add it to this manifold. I have the big 3 bolt ons as well so I think I will be seeing really nice gains
I'm excited to see this done 1.5. I was really excited to do it on mine, so I'll have to live vicariously through you on the build 👍
1.5Tampa · Feb 1, 2013#221
Originally Posted by suckerface ↑
I'm excited to see this done 1.5. I was really excited to do it on mine, so I'll have to live vicariously through you on the build 👍
lol Ill keep you updated man
ilikericesavannah, ga · Feb 1, 2013#222
I know there is a thread on the 1zz TB. What is the PnP part number on the 1zz TB for the Yaris with DriveByWire?
tooterLos Angeles · Feb 1, 2013#223
The part number on my 1ZZ is:

22030-0D030

And the difference in throttle response is night and day... 🙂

Picture not included in this copy
3cyltrboOttawa · Feb 1, 2013#224
where do I get this throttle body without paying eleventy billion dollars?

presumably you guys (with them) are sourcing off ebay or used places?

W
tooterLos Angeles · Feb 1, 2013#225
Yeah, they can get pricey. I paid the full going price for a used one on ebay that was in really superb condition.

Picture not included in this copy

It was $125 including shipping. They had cheaper ones but some of them look like they were underwarer salvage! 😆
cali yarisThread starterCanoga Park, CA · Feb 1, 2013#226
^ That's about right for a really clean one. Dirty/worn/sketchy would be the $60-70 range. 🙂
1.5Tampa · Feb 1, 2013#227
I bought one used off a member for 55 but it needs a real good cleaning, id also like to Neo chrome it so ill be reinvesting money into it.
Silver StreakMassachusetts · Feb 1, 2013#228
I'm sorry if this has been asked. Is that tb a direct bolt on for our stock intake manifold?
tooterLos Angeles · Feb 1, 2013#229
Originally Posted by Silver Streak ↑
I'm sorry if this has been asked. Is that tb a direct bolt on for our stock intake manifold?
Well, sort of... but not exactly.

A 1ZZ will bolt on because the stud holes are the same as stock at 60mm square, but the diameter of the stock O ring gasket is too small to seal the larger 55mm bore, and I don't believe that the larger butterfly when opened will clear the stock hole either.
Silver StreakMassachusetts · Feb 1, 2013#230
Thanks for the info Tooter.
3cyltrboOttawa · Feb 1, 2013#231
I bought a sketchy looking one (will need a cleaning) for $55

quick question / do I (should I) transfer the electronics from the old to the new? (looks interchangeable?) or is it simply plug and play?
tooterLos Angeles · Feb 2, 2013#232
I switched mine just to be sure, but you could try it first with the 1ZZ chip.

But I do know this from personal experience... it will NOT work unless you chip out the epoxy and turn the allen key head idle screw counterclockwise about a turn...

Picture not included in this copy

It's that tiny screw just above the upper left hand throttle body stud... and don't strip it. 👍
1.5Tampa · Feb 2, 2013#233
@tooter so the tb installation requires a larger o ring, possible chip swap, removal of epoxy, and adjusting the idle set screw? I skipped anything about the butterfly valve needing space since Im sure MI thought of those dimmensions with the new manifold design since they wanted to be able to combine the two for even better performance.
tooterLos Angeles · Feb 2, 2013#234
Originally Posted by 1.5 ↑
@tooter so the tb installation requires a larger o ring, possible chip swap, removal of epoxy, and adjusting the idle set screw? I skipped anything about the butterfly valve needing space since Im sure MI thought of those dimmensions with the new manifold design since they wanted to be able to combine the two for even better performance.
You're absolutely right. A larger butterfly likely won't clear a smaller stock bore, so it's a simple matter to make a larger bore and larger diameter gasket to fit both throttle bodies.
Picture not included in this copy

You want the flow to be compatable with the larger throttle body anyways.
cali yarisThread starterCanoga Park, CA · Feb 2, 2013#235
I got PM's that the thread has become confusing, and I can't prune it, so.....

For those following along, please note that posts from #231 on (Silver Streak) refer to swapping a 1ZZ throttle body onto a STOCK manifold, and are not about the MICRO IMAGE manifold.

Our manifold comes with the O-ring, is a direct bolt-on, and requires no modifications to use either a 1ZZ throttle body or your stock 1NZ throttle body.
1.5Tampa · Feb 2, 2013#236
awesome ^^

sorry to get off topic
4/20 NEVER FORGETPortland, OR · Feb 2, 2013#237
Awesome! I'm so excited to see the new version of the manifold. I've already got my information in and am on the wait list. I can't wait to get this and install it with my 1ZZ throttle body.
GolddeenohColumbia, SC · Feb 2, 2013#238
now to get Garm to confirm the intake kit that comes with the 1zz throttle body and a set of 1zz injectors. hint hint...
4/20 NEVER FORGETPortland, OR · Feb 2, 2013#239
Why would you need 1zz injectors? I mean, I understand that they are a larger injector, but unless you are going turbocharged/supercharged, what's the point? Seems like it would be a bit overkill for NA.
1.5Tampa · Feb 2, 2013#240
Not necessarily, a large TB and upgraded manifold will lean out the mixture. I'm sure the maf will see more air coming in and increase the fuel delivery but if the stock injectors can't pump anymore, then the 1zz should meet those needs. More air + more fuel = more explosions = more power.
cali yarisThread starterCanoga Park, CA · Feb 2, 2013#241
^ I don't see this manifold + 1ZZ TB requiring larger injectors.

Dynos will tell, but it certainly doesn't need them with the stock TB - as shown on the dyno.
4/20 NEVER FORGETPortland, OR · Feb 2, 2013#242
Originally Posted by 1.5 ↑
More air + more fuel = more explosions = more power.
Not always. I've dyno-tuned two Hondas I've owned in the past with VAFCs and wide-band, both with many bolt-on mods and larger throttle bodies. Naturally aspirated, with stock injectors, EVERY TIME I made power by reducing the fuel injector pulse from stock. You'd be surprised what the stock injectors are capable of, every time I've put a car on a dyno with a wide-band o2, the car was running rich and I ended up taking away fuel to make power. In the case of my H22A-swapped Civic, I made 9 hp and 10 tq at the wheels with just a VAFC and some dyno time. The fuel and air mixtures need to be in balance, too much of either one isn't a good thing.

More air + balanced fuel = more power
More air + too much fuel = less power, lower mpg
3cyltrboOttawa · Feb 6, 2013#243
anyone get theirs yet?

pictures? / install impressions?

sound? / buttdyno?

Will
1.5Tampa · Feb 6, 2013#244
not yet but I am dying waiting lol

mines in finishing right now
tooterLos Angeles · Feb 6, 2013#245
Originally Posted by 1.5 ↑
not yet but I am dying waiting lol

mines in finishing right now
Can't wait to actually see one! 🙂
Be sure to post lots of pictures. If yours is only being finished now, they must be shipping directly from Golden Eagle. Isn't there anyone else here who actually has one?
1.5Tampa · Feb 6, 2013#246
well they only got 3 and mine is one of those and its actually being custom plated... I couldnt keep it a secret anymore lol so its taking a while

the other 2 may have shipped out already unless maybe garm is keeping one to put on his hatch
YodaFL · Feb 6, 2013#247
i really cant imagine the need for bigger injectors for this N/A setup. Your better off getting your car tuned.
4/20 NEVER FORGETPortland, OR · Feb 6, 2013#248
I've tried calling and emailing but don't have a date as to when I'm getting one shipped to me yet. I WANT so badly. When I do get one I'll be sure to post lots of pics and try and get it to a dyno after install.
Captain SlowScott, LA · Feb 6, 2013#249
Forgive me for not wanting to read through 14 pages of posts....but is there any dyno data on this intake manifold to show the gains? thanks.
1.5Tampa · Feb 6, 2013#250
Originally Posted by tooter ↑
Ok... I see the 7 foot pounds of torque, and almost 5 horsepower... 🙂

Picture not included in this copy

...and hoping that Garm will post some pictures.
Here you go