waiting for printout lol
Micro Image Intake Manifold thread
467 posts · 153,219 views · page 3 of 10
Replies continued
Great results! Very pleased :) Garm should be chiming in shortly...
SUCCESS. Didn't make much top end, but a nice midrange bump, right where you want it. Specs and dyno charts to be posted later. Couple of small improvements to be made in production.
I'm happy.
I'm happy.
Nice!
PICS AND VIDS!
and boobs.
and boobs.
Awesome!!! I look forward to seeing the results and buying one!!
nice to see somebody finally bringing out an intake manifold...I cant stand the plastic one...will be saving up for this mod for certain...
I guess ill start saving. Damnit how am i suppost to buy a house??!!
How much of a bump???😈Originally Posted by cali yaris ↑SUCCESS. Didn't make much top end, but a nice midrange bump, right where you want it. Specs and dyno charts to be posted later. Couple of small improvements to be made in production.
I'm happy.
Intake manifold notes and specs from today. As always, you can count on full disclosure and 100% information when we have something to show you.
I'm pretty happy with the results.
Our manifold made some nice power in the 3000-5000 rpm range, where most people will use it well. With some tuning, the top end will yield some power as well, AFR went pig rich at 5500+
ambient temperature was 90 degrees F
87 octane (91 would have helped us)
tested on a stock Yaris
Engine and bay were hotter for the pulls with MI manifold
Dyno Dynamics (tough dyno with numbers, 10-15% lower than DynoJet)
***some changes and improvements to be made in production
rich on top -- will deliver more power with some tuning
no CEL's
sounds badass 😁
Here is the dyno chart (sorry for the large image). Grey is MI manifold, the other line is stock plastic mani. Chart shows power and torque comparisons.
Picture not included in this copy
here's a YouTube vid:
http://www.youtube.com/watch?v=IIMXX8bw8lE
I'm pretty happy with the results.
Our manifold made some nice power in the 3000-5000 rpm range, where most people will use it well. With some tuning, the top end will yield some power as well, AFR went pig rich at 5500+
ambient temperature was 90 degrees F
87 octane (91 would have helped us)
tested on a stock Yaris
Engine and bay were hotter for the pulls with MI manifold
Dyno Dynamics (tough dyno with numbers, 10-15% lower than DynoJet)
***some changes and improvements to be made in production
rich on top -- will deliver more power with some tuning
no CEL's
sounds badass 😁
Here is the dyno chart (sorry for the large image). Grey is MI manifold, the other line is stock plastic mani. Chart shows power and torque comparisons.
Picture not included in this copy
here's a YouTube vid:
http://www.youtube.com/watch?v=IIMXX8bw8lE
Do you have the AFR graph as well?
We did not have a chance to test it with the 1ZZ throttle body today, but that probably would have helped a bit more. Just a guess. Future dyno session for sure.
bluevitz, yes, I'll post that next.
Picture not included in this copy
Im liking this.
1zz tb and tune damn skippy
1zz tb and tune damn skippy
I wonder why the ecu decided to go so rich? I guess a tune will squeeze a bit more out.
I can't wait to buy one and install it with a 1zz tb. Any plans to try it out on a yaris with some mild mods? Id love to see how this does on a car with i/h/e and a 1zz tb.
^ I sure want to or with a Zage kit at low boost.
I think I'll throw one on my car with a 70mm TB and see what it pulls too. Let's see what 25 psi does to it. 😆
I think I'll throw one on my car with a 70mm TB and see what it pulls too. Let's see what 25 psi does to it. 😆
Congratulations, Garm! It looks like a really nice fat torque curve. 👍
In what gear did you run it? My runs took about three times as long as your dyno video! 😆 Also what intake did you run on the throttle body. It was difficult to make it out in the video.
In what gear did you run it? My runs took about three times as long as your dyno video! 😆 Also what intake did you run on the throttle body. It was difficult to make it out in the video.
3rd gear pulls. Simota air filter (I think) on stock throttle body/MAF tube. (the rubber tube that feeds the stock airbox).
we tried pulls with and without air filter attached -- made no difference in power/torque at all.
we tried pulls with and without air filter attached -- made no difference in power/torque at all.
gonna blow the welds right off the mainfold. 😆Originally Posted by cali yaris ↑^ I sure want to or with a Zage kit at low boost.
I think I'll throw one on my car with a 70mm TB and see what it pulls too. Let's see what 25 psi does to it. 😆
Toyotas always seem to dump fuel on the top end. My tercel before the turbo would go to 10.3-10.5 range for the last 1200rpm...i called it Evo style...just blowing out black smoke.
Its also why i can get away with mild boost with no tuning...im still 11.6~ on the top end
Its also why i can get away with mild boost with no tuning...im still 11.6~ on the top end
Yeah I observed that too on the 1NZ, perhaps it's a feature from Toyota engineers, prevent detonation in the worst possible conditions?Originally Posted by malibuguy ↑Toyotas always seem to dump fuel on the top end. My tercel before the turbo would go to 10.3-10.5 range for the last 1200rpm...i called it Evo style...just blowing out black smoke.
Its also why i can get away with mild boost with no tuning...im still 11.6~ on the top end
My sentiments exactly, but I want one.Originally Posted by malibuguy ↑I guess ill start saving. Damnit how am i suppost to buy a house??!!
Can you help me out here, Garm? Because now I'm really confused.😕Originally Posted by cali yaris ↑3rd gear pulls.
3rd gear would have been cheating anyway. 😉
1 to 1 is the most accurate, and the pull is long enough to record with precision -- in tooter's case, great precision. 😆
Won't the car hit the speed limiter in 4th?
Anyway shouldn't matter, it's all calculated numbers anyway. The only true measure of power is directly off the crankshaft. The gearbox is simply a tourque multiplier to allow the car to move at different speeds.
Anyway shouldn't matter, it's all calculated numbers anyway. The only true measure of power is directly off the crankshaft. The gearbox is simply a tourque multiplier to allow the car to move at different speeds.
Thanks for setting me straight, Blue. 👍Originally Posted by Bluevitz-rs ↑Won't the car hit the speed limiter in 4th?
Anyway shouldn't matter, it's all calculated numbers anyway. The only true measure of power is directly off the crankshaft. The gearbox is simply a tourque multiplier to allow the car to move at different speeds.
The engine hit the limiter in 4th with both manifolds.
It just took 30 seconds to get there. 😆
wicked!!!!!
I hit the limiter for 4th right now...guess boost helps a LOT 🤣Originally Posted by Bluevitz-rs ↑Won't the car hit the speed limiter in 4th?
Anyway shouldn't matter, it's all calculated numbers anyway. The only true measure of power is directly off the crankshaft. The gearbox is simply a tourque multiplier to allow the car to move at different speeds.
I think we got enough accuracy with 3rd gear pulls to be able to compare the stock part to the part we made. That's all I was after. If I just wanted the highest number possible, I would have booked a more forgiving dyno machine.
On my car, we've done 4th gear pulls -- no speed limiter, rev limiter programmable, and 3rd gear goes by pretty quickly. I did have an assumption then that 4th gear would be better for all cars, but I think I was incorrect about that being a hard rule.
On my car, we've done 4th gear pulls -- no speed limiter, rev limiter programmable, and 3rd gear goes by pretty quickly. I did have an assumption then that 4th gear would be better for all cars, but I think I was incorrect about that being a hard rule.
^ looks like that is the case. As previously stated a part like this could really be a crapshoot and in this case it was a positive result even on a car with limited mods so that is a big plus.
Forgot to shout out to the dyno shop - thank guys!
KT Motoring
10149 Canoga Ave. Unit 1
Chatsworth, CA 91311
747.224.0237
KT Motoring
10149 Canoga Ave. Unit 1
Chatsworth, CA 91311
747.224.0237
Any chance of a 1ZZ version with nitrous ports?
This is going to be interesting!Originally Posted by cali yaris ↑^ I sure want to or with a Zage kit at low boost.
I think I'll throw one on my car with a 70mm TB and see what it pulls too. Let's see what 25 psi does to it. 😆
Of course there will be gains over the plastic one.
Well lets find out with the boosted motors.
I better start saving!
Thats wild. As piston speed increases the likelyhood of autoignition decreases... maybe the ecm is throwing a lot of advance at that part of the curve too.Originally Posted by eTiMaGo ↑Yeah I observed that too on the 1NZ, perhaps it's a feature from Toyota engineers, prevent detonation in the worst possible conditions?
I'm ready to buy! I can't wait to see these go on sale.
My timing on the top end is around 24* iirc....stupid low timing if you ask me.Originally Posted by chaditotx ↑Thats wild. As piston speed increases the likelyhood of autoignition decreases... maybe the ecm is throwing a lot of advance at that part of the curve too.
I used to run one oy old malibus at 15* initial and 44* total...ran awesome too
Yeah the timing backs way off as RPM climbs. An old acquaintance put a programmable ecu on his echo and said he added 20° of timing to the top end and gained a whack of top end power with nothing more than the regular boltons.
Sometimes I miss my carburetors... I wonder if there is a way to adjust the position of the crankshaft position sensor and just have the damn thing advanced 2 degrees from the get go
Theres absolutely no way to move the sensor but you could have a new pickup wheel made up or try and rotate it somehow.
Originally Posted by 4/20 NEVER FORGET ↑I'm ready to buy! I can't wait to see these go on sale.
I'm feeling a bit more coming from that manifold with an exhaust, header and a cold air.... I am really excited to see what it does when it breathes on both ends. 🤘Originally Posted by cali yaris ↑I think we got enough accuracy with 3rd gear pulls to be able to compare the stock part to the part we made. That's all I was after. If I just wanted the highest number possible, I would have booked a more forgiving dyno machine.
On my car, we've done 4th gear pulls -- no speed limiter, rev limiter programmable, and 3rd gear goes by pretty quickly. I did have an assumption then that 4th gear would be better for all cars, but I think I was incorrect about that being a hard rule.
i was watching my scangauge this weekend...up in the top end in boost my timing is down to around 15*...i could probably run diesel in this thingOriginally Posted by Bluevitz-rs ↑Yeah the timing backs way off as RPM climbs. An old acquaintance put a programmable ecu on his echo and said he added 20° of timing to the top end and gained a whack of top end power with nothing more than the regular boltons.
🤤
1 attachment not included in this copy
Any more info? It's been almost a month since the last post to this thread. I love the handling of my Yaris (Megan Racing coil overs and Ultra Racing chassis bracing) but it DEFINITELY needs more power. I want one of these intakes with a larger throttle body!
along for the ride. Starting to mod my gf's yaris (our daily).
I received the modified prototype on Friday. I'm working on getting the test car again to do a final fitment and decide which version to make a bunch of.
As far as I'm concerned it was pretty close last version, but we did a little more tweaking to get more stock hoses to fit without needing replacement, and MAYBE to be able to connect the manifold to the stock airbox.
I'll know this week.
As far as I'm concerned it was pretty close last version, but we did a little more tweaking to get more stock hoses to fit without needing replacement, and MAYBE to be able to connect the manifold to the stock airbox.
I'll know this week.
I'm concerned about fitment with the Mishimoto radiator...from the pic it looks a little tight, will it clear?
I happen to have a Zage kit waiting for a good reason to be installed, hehe.
I happen to have a Zage kit waiting for a good reason to be installed, hehe.
nice looking piece!
Which mishimoto are you using ?Originally Posted by mazilla ↑I'm concerned about fitment with the Mishimoto radiator...from the pic it looks a little tight, will it clear?
I happen to have a Zage kit waiting for a good reason to be installed, hehe.