It's really close, but bellmouth doesn't quite fit in all the way. I purposefully drilled the hole small as the hole saw does a considerable bit of wandering. This gives me the opportunity to precisely trim the hole for a good fit. I'll post a pic of the inside when I'm done with grinding the opening. 🙂Originally Posted by Flipper_1938 ↑What does the boob look like on the inside with the flange fitted?
tooter's manifold adventure...
1,454 posts · 559,522 views · page 27 of 30
Replies continued
After a couple of hours grinding filing and sanding the bellmouth has a nice snug fit... 🙂
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
The runners remain in direct alignment with the axis of the throttle body bore...
Picture not included in this copy
Picture not included in this copy
This is the inside of the plenum, there is a complete lack of any flat reflective surfaces. I'll find out what happens then the pulses travel out the mouths of the runners and hit only curved surfaces.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
The runners remain in direct alignment with the axis of the throttle body bore...
Picture not included in this copy
Picture not included in this copy
This is the inside of the plenum, there is a complete lack of any flat reflective surfaces. I'll find out what happens then the pulses travel out the mouths of the runners and hit only curved surfaces.
Picture not included in this copy
So many Freudian themes in this project! I was wondering where the actual seam would be on the bellmouth--for some reason I was thinking you would put it all the way up to the squared shoulders.
It looks from the picture, that because of the angle, the throttle body points more directly at two runners, which are slightly further away. See your second picture above. It would be interesting to see a flow test for to see how much each runner is getting.
That's right, Cranky. I had originally planned for it to drop all the way down to the square corners, but that makes the round part of the bellmouth drop below the contact surface of the hemisphere creating a gap. While the welder could easily fill that gap, I want to try to keep burn through to a minimum by retaining complete contact between the two surfaces so that the inside surface is not compromised.Originally Posted by CrankyOldMan ↑So many Freudian themes in this project! I was wondering where the actual seam would be on the bellmouth--for some reason I was thinking you would put it all the way up to the squared shoulders.
It took a couple of hours of handwork to get the fit as precise as possible, and I'm totally satisfied with the results. 🙂
Picture not included in this copy
Picture not included in this copy
When I bead blast the whole assembly to normalize all of the surfaces, you'll hardly be able to see the seam even with no welding.
The raised square corners will end up working out nicely as the whole circle of the contact seam is easily accessible to be welded from the outside of the hemisphere. Exploring how to make the best of each detail in the design process is what makes this project no end of fun. 🙂
I know. The offset angled orientation of the throttle body axis in the original plenum was even more offset than the one I'm building. So I softened it slightly. If it wasn't an issue for Toyota, it isn't for me. I think it was done just to get the throttle body pointing slightly upwards to line up with the stock air filter box, so I did the same thing so as to line up with mine. 😉Originally Posted by cali yaris ↑It looks from the picture, that because of the angle, the throttle body points more directly at two runners, which are slightly further away. See your second picture above. It would be interesting to see a flow test for to see how much each runner is getting.
Picture not included in this copy
This is the original manifold throttle body axis orientation.
Picture not included in this copy
And this is the tooter et throttle body orientation.
Picture not included in this copy
This is why I don't believe that it was ever an issue. First because the flow is so direct, and second the runners are pulling from the plenum That's what I like most about this particular design. It completely eliminates the 90 degree "kink" runner to throttle body axis orientation found in all of the other typical plenum designs.
Looking ever sooooo smooth!!! Nice!!
Is it done yet?
^ He is currently testing it on Alpha Centauri.
Hey that's the post I see the most on my thread, Something Big is Coming! 😆Originally Posted by Flipper_1938 ↑Is it done yet?
Not yet.Originally Posted by Flipper_1938 ↑Is it done yet?
Right now, the CNC machinist is making a base plate to connect the hemisphere to the intake runners. After that, I make the 3 tubing fittings, everything gets welded up and then I get to drive it. 👍
The machine shop at Origin Designs made two more flanges. Their work is impeccable...
Picture not included in this copy
Also got a Corolla manifold to build into another tooter. 😉
Picture not included in this copy
Also got a Corolla manifold to build into another tooter. 😉
Nothing like billet jewelry.
Here's the CNC machine making tooter intake manifold flanges two at a time... 🙂
http://www.youtube.com/watch?v=rh4Ho5tI8KA
http://www.youtube.com/watch?v=rh4Ho5tI8KA
Picked up the tooter et plenum to runner connecting plate today. It's far beyond what I had expected! 🙇 The plate fits so precisely to the runner base, I couldn't pry it off so I'll just leave there to be welded on. the hemisphere sets on a ledge and centers itself.
Picture not included in this copy
Picture not included in this copy
Now I'll do one last on the car fitting to rotate the hemisphere and mark the best attitude of the throttle body to line up with the intake.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Next, the hemisphere will be drilled to accept some aluminum tubes for the three hose fittings. Then the whole assembly goes off to the welder! 👍
Picture not included in this copy
Picture not included in this copy
Now I'll do one last on the car fitting to rotate the hemisphere and mark the best attitude of the throttle body to line up with the intake.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Next, the hemisphere will be drilled to accept some aluminum tubes for the three hose fittings. Then the whole assembly goes off to the welder! 👍
Looks great!
Tooter's Titter!Originally Posted by tooter ↑Picked up the tooter et plenum to runner connecting plate today. It's far beyond what I had expected! 🙇 The plate fits so precisely to the runner base, I couldn't pry it off so I'll just leave there to be welded on. the hemisphere sets on a ledge and centers itself.
Now I'll do one last on the car fitting to rotate the hemisphere and mark the best attitude of the throttle body to line up with the intake.
Picture not included in this copy
Next, the hemisphere will be drilled to accept some aluminum tubes for the three hose fittings. Then the whole assembly goes off to the welder! 👍
Looks like quality design and manufacturing! I'm anxious to see how it works.
This is just a one-off "outside the box" experiment that will never see production because it's not cost effective. It's pure exploration just for the sake of curiosity. 🙂
If it makes a big number, I bet somebody will pay you to make another one.Originally Posted by tooter ↑This is just a one-off "outside the box" experiment that will never see production because it's not cost effective. It's pure exploration just for the sake of curiosity. 🙂
After all, you now have a parts list (with math data).
Although visually different, both plenums still hold the same 26 ounces of water. So the difference may not be that much. I'm curious as to whether a radically different plenum shape will make more gains. After a considerable amount of internet searching, as far as I know no one has ever tried anything as strange as this before. So we'll see what happens... 😉Originally Posted by Flipper_1938 ↑If it makes a big number, I bet somebody will pay you to make another one.
After all, you now have a parts list (with math data).
Looking forward to the results :)
This one looks a little like your design.
1 attachment not included in this copy
Hey, what do you know. Someone did that design. Guess the old saying is true that there's nothing new under the sun. 😆 What car did that come off of?Originally Posted by kou ↑This one looks a little like your design.
That manifold is off a toyota 4e-fe engine
1 attachment not included in this copy
Makes sense that it would be Toyota as it's similar to the Corolla manifold. Even the mandrel bent tubing looks familiar.
Picture not included in this copy
Just did a search on WIKI. That manifold design was on the last 4E FE 1.5 engine which was discontinued in 1997. In 1998 the Corolla 1ZZ FE 1.8 engine carried over the similar design.
Picture not included in this copy
Just did a search on WIKI. That manifold design was on the last 4E FE 1.5 engine which was discontinued in 1997. In 1998 the Corolla 1ZZ FE 1.8 engine carried over the similar design.
The tooter et just grew some new antennae... 🙂
Picture not included in this copy
Picture not included in this copy
So now it's off to the welder! 🙂
Picture not included in this copy
Picture not included in this copy
So now it's off to the welder! 🙂
Huzzah!
Awesome! alien like...
Is it done yet?
It's at the welder today. 🙂
When that's done
it's ready to run. 👍
Before dropping it off, I finished porting all of the runners and bead blasted the insides as it's the last time I'll be open to do anything to it.
Picture not included in this copy
For comparison, this is before porting...
Picture not included in this copy
I should have the tooter et up and running on the car by Friday.
When that's done
it's ready to run. 👍
Before dropping it off, I finished porting all of the runners and bead blasted the insides as it's the last time I'll be open to do anything to it.
Picture not included in this copy
For comparison, this is before porting...
Picture not included in this copy
I should have the tooter et up and running on the car by Friday.
Came up with another idea... 🙂
TOOTER II.VII
Picture not included in this copy
It's for a Toyota Tacoma 2.7 4 cylinder... a 2 inch thick intake manifold spacer that makes the runners 12% longer to lower the torque curve. The prototype should be done and ready for testing in a week. I'll drive it around to let the ECU learn the new operating parameters...
...and then it's off to Harry's Dyno Shop for a few runs. 👍
TOOTER II.VII
Picture not included in this copy
It's for a Toyota Tacoma 2.7 4 cylinder... a 2 inch thick intake manifold spacer that makes the runners 12% longer to lower the torque curve. The prototype should be done and ready for testing in a week. I'll drive it around to let the ECU learn the new operating parameters...
...and then it's off to Harry's Dyno Shop for a few runs. 👍
Awesome!! 👍Originally Posted by tooter ↑Came up with another idea... 🙂
TOOTER II.VII
Picture not included in this copy
It's for a Toyota Tacoma 2.7 4 cylinder... a 2 inch thick intake manifold spacer that makes the runners 12% longer to lower the torque curve. The prototype should be done and ready for testing in a week. I'll drive it around to let the ECU learn the new operating parameters...
...and then it's off to Harry's Dyno Shop for a few runs. 👍
Is it done yet?
The welder might be done with it as soon as today... 🙂
I'm not even going to clean it up, it goes right on the car to find out if it will actually work.
edit: Just called the welder and it'll be done this afternoon!
(yipee 🙂 )
I'm not even going to clean it up, it goes right on the car to find out if it will actually work.
edit: Just called the welder and it'll be done this afternoon!
(yipee 🙂 )
👍
👏
🤤
🙂
🤘
🎉
👏
🤤
🙂
🤘
🎉
Hey Flip... 🙂
Just picked it up!
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
My wife is using the car today so I can't put it on yet. 🙁 But tomorrow morning it'll be on the engine and I'll be driving it.
Greg
Just picked it up!
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
My wife is using the car today so I can't put it on yet. 🙁 But tomorrow morning it'll be on the engine and I'll be driving it.
Greg
Since I had the time, all of the welds got a quick bead blast to normalize the surface... 🙂
Picture not included in this copy
Picture not included in this copy
That looks awesome!! I need to make a trip up to LA and come check the work out in person....
Lookin good, can't wait for the driving report tomorrow!
It should work just fine since Toyota had already put the same design on their cars... 😉
Picture not included in this copy
I haven't been able to find this manifold in the US. However, it was installed on 1998 Toyota Starlets in the UK and in Pakistan.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
I'd love to find one and see if the tooter flange would fit onto it, because building the tooter et took a lot of work. 🙄
Picture not included in this copy
I haven't been able to find this manifold in the US. However, it was installed on 1998 Toyota Starlets in the UK and in Pakistan.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
I'd love to find one and see if the tooter flange would fit onto it, because building the tooter et took a lot of work. 🙄
Let me know when you'd like to visit. That would be fun. 🙂Originally Posted by JustDidIt ↑That looks awesome!! I need to make a trip up to LA and come check the work out in person....
Greg
Got the tooter et up and running this morning... 🙂
Picture not included in this copy
I messed up a little on the attitude of the throttle body as the rotation is about 30 degrees off, but it's not enough to keep it from working.
Drove it only a little bit today because of work, and it drives really good 🙂 even with ECU just relearning the new operating parameters. It's just as quiet as stock in regular driving, but makes a really cool swooshing bwwwaaa sound when you step on the gas pedal. I think that's because there are no baffles in the plenum like there are in the regular tooter. And also I did a lot of porting on the mouths of the runners so that they are way more open and less restrictive than they were before.
I'm going to drive it around until everything is acclimated and then put it on the dyno, as that's the most trustworthy indicator of any changes. 👍
Picture not included in this copy
I messed up a little on the attitude of the throttle body as the rotation is about 30 degrees off, but it's not enough to keep it from working.
Drove it only a little bit today because of work, and it drives really good 🙂 even with ECU just relearning the new operating parameters. It's just as quiet as stock in regular driving, but makes a really cool swooshing bwwwaaa sound when you step on the gas pedal. I think that's because there are no baffles in the plenum like there are in the regular tooter. And also I did a lot of porting on the mouths of the runners so that they are way more open and less restrictive than they were before.
I'm going to drive it around until everything is acclimated and then put it on the dyno, as that's the most trustworthy indicator of any changes. 👍
👏👏👏👏👏
🤤
Oops, I guess you could cut it off again and have it rewelded.
relocate the battery or get a capacitor style battery like CTScott is experimenting with and it will be gravy.
^ A small dry cell battery would work great, that's what I use in my cars. Mine weighs 4 pounds. 🙂
Way to go, tooter 😉
Way to go, tooter 😉
That's exactly what I'm going to do. It's a small issue and simple to resolve. That's the beauty of aluminum. It's easy to work with. But before I do that, first I want to drive it around and then put it on the dyno, because rotating the throttle body is only for aesthetics and isn't going to make any difference in how it runs. 👍Originally Posted by Bluevitz-rs ↑Oops, I guess you could cut it off again and have it rewelded.
Can't wait to hear the audio of the intake!Originally Posted by tooter ↑Got the tooter et up and running this morning... 🙂 👍
Took it for a long drive up north on the 5 freeway (65-80mph) and up to Mt. Pinos and got 42.6 mpg in 248 miles. 🙂
It's ready to dyno now, so when work allows I'll be off to Harry's shop. 👍
It's ready to dyno now, so when work allows I'll be off to Harry's shop. 👍