Yarisworld Archive

STF posts

647 posts · 143,819 views · page 7 of 13

Replies continued

ilikericeThread startersavannah, ga · Apr 2, 2013#301
Interesting..
xnamerxxso cal · Apr 2, 2013#302
For anyone who was wondering Rival vs Toyo in width.
And you can see my severely overheated Toyos in the picture.

Picture not included in this copy
Jason@SportsCarDebary, FL · Apr 2, 2013#303
You are not getting very even tire wear.


Originally Posted by xnamerxx ↑
For anyone who was wondering Rival vs Toyo in width.
And you can see my severely overheated Toyos in the picture.

Picture not included in this copy
xnamerxxso cal · Apr 2, 2013#304
Yep, really really bad shoulder wear...even with -3.5 camber. I do think most of it is from me over driving the car though.

I talked to Andy Hollis about that at Nationals last year, since the same thing was happening to him. I don't think I could ever get enough static camber to make these tires work to the fullest.
racerbLeland, NC · Apr 2, 2013#305
Thats the one issue I always had with Solo, no real time to dial in camber, toe, tire temps, and pressures. The only Toyos I've ever ran are the RA-1s on road race cars, as for auto-x it's been BFG Comp T/As, Bridgestone RE-11s, Yokohama A001Rs and Falken Azenis 215s. I know kinda shows how long ago I ran alot, but judging by what I've seen lately the new Rival looks very strong! If you can get advice from Andy Hollis, take it as gospel, he and his wife Ann were already top competitors in '84 when I ran at the Solo II Nationals in Salina Kansas. One thing I have learned through lots of trial and error is to slow down and go faster, best way is to slow your hands down while limiting your steering inputs. Good luck with your car, I'll be working on the STF set-up on my Yaris this season as well.

racerb
xnamerxxso cal · Apr 3, 2013#306
So to add onto the rear toe change, I'm not sure if I'm crazy or not but I'm having a much more difficult time to induce inside spin.
It seems that having less steering input also helps in reducing inside spin which makes sense but I didn't expect this drastic of a change, on my test route I found I was able to get on the gas way way sooner than I normally would while still being able to keep the car pointed where I wanted too.

Not sure if this will pan out during a race but it certainly was surprising, in a good way, driving around.
xnamerxxso cal · Apr 14, 2013#307
Well found a problem with my car I wasn't anticipating, while checking my compression travel I realized I have a little less than 2" of compression travel...not good. Not sure how I'm going to fix this one.
Jason@SportsCarDebary, FL · Apr 14, 2013#308
Originally Posted by xnamerxx ↑
Well found a problem with my car I wasn't anticipating, while checking my compression travel I realized I have a little less than 2" of compression travel...not good. Not sure how I'm going to fix this one.
I have about 1.5" before I hit the front bumpstops. How are your fronts built? We cut the ears off the tubes and moved them up to get an extra .5" when they were first built. You can always go up on spring rate.
xnamerxxso cal · Apr 14, 2013#309
The ears are welded on I believe but I'd have to double check. I've got roughly an inch or so of compression travel before I hit bump stop travel and another inch or so of bump stop travel.

I just put my stiffer springs on but I'm guessing I might need to go even stiffer to get around this problem with my current struts. I'm thinking of just grabbing a set of Koni race inserts and modifying my kyb struts or just picking up a set of tubes from some random company. I'll talk to Bilstein tomorrow to see if they can shorten the shock body, but guessing from the response I got last time I don't think its going to be something they'll do.
Jason@SportsCarDebary, FL · Apr 14, 2013#310
Originally Posted by xnamerxx ↑
The ears are welded on I believe but I'd have to double check. I've got roughly an inch or so of compression travel before I hit bump stop travel and another inch or so of bump stop travel.

I just put my stiffer springs on but I'm guessing I might need to go even stiffer to get around this problem with my current struts. I'm thinking of just grabbing a set of Koni race inserts and modifying my kyb struts or just picking up a set of tubes from some random company. I'll talk to Bilstein tomorrow to see if they can shorten the shock body, but guessing from the response I got last time I don't think its going to be something they'll do.
Are your fronts inverted?
xnamerxxso cal · Apr 15, 2013#311
Yeah the fronts are inverted.
Jason@SportsCarDebary, FL · Apr 15, 2013#312
Originally Posted by xnamerxx ↑
Yeah the fronts are inverted.
Should be easy to cut the tabs off and install a new set further up - assuming you are not to close to the axle already.
xnamerxxso cal · Apr 16, 2013#313
Well I found part of the problem, it appears I have 2 giant bump stops inside the housing so I can probably axe one and be safe. That should net me close to an inch.
CrankyOldManWest Michigan · Apr 16, 2013#314
How did you discover the problem? I just went back to stock bump stops on my Tokico blues/Tien S-techs after running last summer with a 2" chop. I'm concerned about "riding" the stops, but not sure how I would find out.
xnamerxxso cal · Apr 16, 2013#315
I was measuring how much travel I had along with bumpsteer and camber gain/loss.

So basically I yanked the spring off and cycled the suspension and took measurements of everything. If you have some free time and can remove your spring its pretty easy to do, since I have coilovers its really easy for me to do.

I'm sitting at about a 2" drop give or take maybe a little less.
justjesusOrange County · Apr 23, 2013#316
DAMN. Fancy guy!

I'm going to get coilovers just so you can come over and do that on my car :)
xnamerxxso cal · Apr 28, 2013#317
Originally Posted by justjesus ↑
DAMN. Fancy guy!

I'm going to get coilovers just so you can come over and do that on my car :)
Its almost as easy to do with lowering springs, since the tophat doesn't normally require pre tensioning.

I had last years STC champ take a trip in my car today and got tips on getting my car setup. So now its off to find very stiff springs 600lb+ and remove my FSB.

Here is a video of the practice course, really fun course but with the decreasing radius sweepers I was having a hard time.

Also managed to Max out the amount of camber I can get somewhere in the 4+ degree range knuckle is hitting the strut body so can't go any further. First time my tires ever wore evenly though.

http://www.youtube.com/watch?v=AqJX7...ature=youtu.be
ilikericeThread startersavannah, ga · Apr 28, 2013#318
new tires arrived for the season. Mounted and Balanced.

Gotta break them in this week before autocross next sunday

1 attachment not included in this copy

racerbLeland, NC · Apr 28, 2013#319
Originally Posted by CrankyOldMan ↑
How did you discover the problem? I just went back to stock bump stops on my Tokico blues/Tien S-techs after running last summer with a 2" chop. I'm concerned about "riding" the stops, but not sure how I would find out.
The easiest way to check travel on your suspension is an old circle track trick that we used to do with our road race Nissan. All you need is a ziptie that you place just above the bump stop around the strut/shock piston shaft, take it out run it and see where the ziptie ends up. Then just measure the distance between bump stop and ziptie and there you have it shock travel.

Riding on the bump stops is not bad thing, it save the internals of your strut/shocks, shorter housings with shorter inserts will be the next item of choice.

racerb 👍
racerbLeland, NC · Apr 28, 2013#320
Originally Posted by xnamerxx ↑
Its almost as easy to do with lowering springs, since the tophat doesn't normally require pre tensioning.

I had last years STC champ take a trip in my car today and got tips on getting my car setup. So now its off to find very stiff springs 600lb+ and remove my FSB.

Here is a video of the practice course, really fun course but with the decreasing radius sweepers I was having a hard time.

Also managed to Max out the amount of camber I can get somewhere in the 4+ degree range knuckle is hitting the strut body so can't go any further. First time my tires ever wore evenly though.

http://www.youtube.com/watch?v=AqJX7...ature=youtu.be
Check with these folks, I've run their springs for years and you can get them at almost any Hot Rod/Circle Track dealer in the US and Canada.http://www.bluecoilspring.com/
I alway bought mine from Hank Thomas Speed Parts in Wimston-Salem NC.... http://www.hankthomasperformance.com/

racerb 👏
xnamerxxso cal · Apr 28, 2013#321
Well today was champ day, car was better today, but def needs the front end worked out. There was another Yaris today, and he looked really good out there. I was honestly shocked at how composed and flat the car was, given the lighter springs he was running.
The secondary driver would have given me a run for my money too but I was running in another class to avoid that beatdown. I think that car how its setup now with better tires would be a hard car to beat.
The only solice I can take is I beat the reigning STU national Champ 👍

Picture not included in this copy
CrankyOldManWest Michigan · Apr 29, 2013#322
Congrats! Looks like all of your hard work is paying off. Do you by chance know what setup the other Yaris had?
xnamerxxso cal · Apr 29, 2013#323
From the brief conversations I had with him, he was running fortune coilovers with 4kf/6kr, 23mm Ultra Racing swaybar, he was using the upper bolt hole on the rear torsion beam, and federal 595 rsr tires.
It definitely look really good out there.
CrankyOldManWest Michigan · Apr 29, 2013#324
Originally Posted by xnamerxx ↑
...he was running fortune coilovers with 4kf/6kr, 23mm Ultra Racing swaybar, he was using the upper bolt hole on the rear torsion beam, and federal 595 rsr tires.
Yikes. I think I'm running slinkies and pogo sticks in comparison. =P
xnamerxxso cal · Apr 29, 2013#325
His car was flatter than mine with 400f/400r, TRD rear bar, and Dunlop Z2 tires. I was more consistent with my times but at the end of the day the co-driver had the faster clean time.
NJ DriveNorthern NJ · Apr 29, 2013#326
Great job! Tristan is an excellent driver. Were conditions consistent throughout the day?
xnamerxxso cal · Apr 29, 2013#327
Tristan ran 2 groups before me at around 11:30 give or take. It was around 85-90 degrees with mild wind but temps were def hotter during my group.

Its a big slick asphault surface, so I probably had the edge tire wise running the z2s where as he was running the Rivals.
racerbLeland, NC · Apr 29, 2013#328
Originally Posted by xnamerxx ↑
From the brief conversations I had with him, he was running fortune coilovers with 4kf/6kr, 23mm Ultra Racing swaybar, he was using the upper bolt hole on the rear torsion beam, and federal 595 rsr tires.
It definitely look really good out there.
Good to hear someone is running the Federals, that is one of the tires on my short list of STF tires, mostly due to cost!!

racerb 🎉
why?harnett county NC · May 4, 2013#329
where did these fortune coilovers come from. Never heard of them, yet I've seen them mentioned a few times on yw today.
CrankyOldManWest Michigan · May 4, 2013#331
So I just ran my first event on Rivals, and I've got mixed feelings about them. Compared to the DZ101's I ran last year, they are a big improvement in grip, but I've lost all sense of hitting cones. So much so that I only had 2 clean runs of 6, but was only aware of a single cone that went bouncing through my rear-view mirror. One run was a +5!

That said, I'll wait to see how I do tomorrow and next weekend before passing judgement.
xnamerxxso cal · May 4, 2013#332
Thats somewhat to be expected.

First off you're learning a new tire which has much higher limited than your old tire, if your car has stockish suspension the car will lean more making inputs delay, and the Rival is a pretty vague tire as it is.

As I like to believe, its better to learn on a crappy tire that doesn't let you make mistakes vs a good tire that does. When I switched to the R1R's I had a really hard time getting used to them, they had so much more grip and let me get away with so much I couldn't tell when I was making mistakes and overdriving the tires.
CrankyOldManWest Michigan · May 4, 2013#333
I'm on Tokico blues and Tien S-techs, with a TRD rear sway bar, so I would call it stock+. I was actually pretty worried about fender rub, but didn't experience any. The cars that I was close to last season all upgraded their tires too, and put a real hurt on me.
xnamerxxso cal · May 27, 2013#334
Finished this weekends autoX and I got my azz handed to me. Part of that is me being unfamiliar with the new setup, part of it was the very difficult to drive course, but most of it is the amazing talent of the drivers in the other Yaris.
I feel if I could have figured out how to drive the car, i'd have seen an additional few seconds drop off my time but that'll come with time. I do know I was having a really hard time getting heat into my tires which has never happened to me before.

Here is my fast run of the weekend.
http://www.youtube.com/watch?v=kItBgm8kuJs



I do feel with the new RSB the car is faster, and my data is pretty telling about it as well but I have no clue on how to drive the car anymore :(
justjesusOrange County · May 28, 2013#335
sounds like you need more seat time.

the charity event being put on by Jay will help in that department. AND NO WORK.

just runs after runs after runs. look for the thread in this section of the forum.
xnamerxxso cal · Jun 1, 2013#336
So I stuck a gopro under the front of my car just to see what's happening. Well here is a screen grab. I don't think adding negative camber is gonna fix this issue.

Picture not included in this copy
ilikericeThread startersavannah, ga · Jun 1, 2013#337
love it when you get 1 up.. Tripod all day!
xnamerxxso cal · Jun 1, 2013#338
It brings a big smile to my face everytime I see it 😁
racerbLeland, NC · Jun 2, 2013#339
Back in my Showroom Stock road racing days, the VW Rabbits would tripod so high I could nearly drive my CRX right under them in the corners! I'm not joking these things would get 1-2 feet off the ground and it would be down-right scary to watch....

racerb 😲
7:34pmBritish Columbia · Jun 9, 2013#341
Originally Posted by xnamerxx ↑
So I stuck a gopro under the front of my car just to see what's happening. Well here is a screen grab. I don't think adding negative camber is gonna fix this issue.
Do you have a RSB?
xnamerxxso cal · Jun 9, 2013#342
😁 yes I do.
7:34pmBritish Columbia · Jun 9, 2013#343
Ever tried taking it off?

Not sure about the geometry of the Yaris but I've seen it work to fix corner in lift.
xnamerxxso cal · Jun 9, 2013#344
Corner lift isn't the issue. My joke about the picture was that my front wheel was almost going positive and I was getting shoulder wear due to tire deflection.
ilikericeThread startersavannah, ga · Jun 9, 2013#345
tire deflection is no laughing matter....
xnamerxxso cal · Jun 9, 2013#346
I wish I could like that comment. LOL


To add a data point. Yesterdays Autox was a 35 second course. The fast cars there were 2 national level STR cars one with 33.5 and the other with 33.7. The only national STC car there managed a 35.5 but its been setup for another driver.

After 30 some odd runs I was able to get my times down to 36.0 with Jason@sportcar driving my car he was able to get a 35.7 after 5 or so runs. All of those on BFG Rivals. So end of the day nearing I decided to put my Z2s on and run a couple of runs. First run with no idea what pressure and tires semi cold I can a 35.8, times stayed about the for the next 3 runs. No change to suspension or anything just swapping tires.

I don't know what to think but for whatever reason the Z2s are faster on asphalt over the rivals but the Rivals are faster on concrete.
racerbLeland, NC · Jul 18, 2013#347
Got my new STF tires today, now just to get them mounted up. Also placed my order for the Tokico Blues and crash bolts, will pick up my TRD springs next week from Sparks. Going in the morning to National Speed to get my Stop Tech brake lines, already have my Hawk HPS pads and ATE Super Blue fluid. Next week will be fun putting everything together and heading to the alignment shop for some tweeking.

http://smg.photobucket.com/user/race...cde4a.jpg.html

http://smg.photobucket.com/user/race...ml?sort=2&o=27


racerb 👍
racerbLeland, NC · Jul 19, 2013#348
Brake lines and TRD springs on their way, hopefully all the parts will arrive in time for next weekends Auto-X. The Micro-Image parts will be coming from the farthest point, so hope they don't get delayed in shipping!

racerb
justjesusOrange County · Jul 19, 2013#349
sounds like a fun project!

I'm making a list of things that I will potentially buy (likely all of it from Micro Image).
Hopefully be done by the end of August
ilikericeThread startersavannah, ga · Jul 19, 2013#350
I need an OEM hood to stay in stf..