Replies continued
xbgodThread starterFlorida · Jan 1, 2011#151Cali this is for you.......
Bar
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
PSI
4.35
5.80
7.25
8.70
10.15
11.60
13.05
14.50
15.95
17.40
18.85
20.30
21.75
23.20
24.66
Description
MVSBROWN
MVSGOLD
MVSBEIGE
MVSGREY
MVSGOLD/BROWN
MVSCOPPER/BROWN
MVSGREY/BROWN
MVSGREYIGOLD
MVSMAROON/BEIGE
MVSCOPPERIMAROON
MVSGREY/GOLD/BROWN
MVSCOPPER/MAROON/BROWN
MVSGREY/MAROON/BROWN
MVSCOPPER/MAROOI\I/BEIGE
MVSGREY/MAROON/BEIGE
each number represents a spring rate color below. This is how Tial does their waste gates.
Thanks Parma, will look at the same issue you had. I hope thats it and problem solved.
And yes will be in around 380 hp when done. That motor of mine is a beast and sounds awsome. It spools up quick with that new GTX style turbo. I have alot more power available just gotta change that spring and fix that tranny cable.
XBG
cali yarisCanoga Park, CA · Jan 2, 2011#152^ I know that. You didn't answer my question.
I'm using a 10 psi spring and I can run up to 30 psi. So what spring are you using now, and what's wrong with it?
ParmasML · Jan 2, 2011#153 Originally Posted by
xbgod ↑ Cali this is for you.......
Thanks Parma, will look at the same issue you had. I hope thats it and problem solved.
And yes will be in around 380 hp when done. That motor of mine is a beast and sounds awsome. It spools up quick with that new GTX style turbo. I have alot more power available just gotta change that spring and fix that tranny cable.
XBG
I fixed it by replacing the cable, don't waste time repairing it. Also had to wait for weeks for the cable tru Toyota service.
380bhp with Nos and Turbo is easily achievable.
Can you give detail information about the head you are running now instead of gude? I am interested because I am running a stock head and I wish to know how much power it's components withstand, especially the valve springs.
xbgodThread starterFlorida · Jan 2, 2011#154Cali,
mine has gold spring in it now. putting in a greygold one by recommendation of my tunner.
My engine is a beast it just keeps wanting to put out more. Never seen it act as powerful as now.
Parma I will defintaley order a new one from Toyota and if need be next day air it in.
Thanks dude.
XBG
cali yarisCanoga Park, CA · Jan 2, 2011#155^ I still don't understand why it's the "wrong" spring.
xbgodThread starterFlorida · Jan 2, 2011#156The gold spring was only allowing me to get to 5.8 psi before it would shut me down. So in order to make more PSI we took the waste gate out of the equation for now and set up the boost controller through the Greddy boost controller only and by-passed the wastegate all together. The problem with that is boost creep so I'm not pushing the envelpoe untill I change the spring sometime next week. Also had to reroute a couple of vacuum lines to do so.
Hope this explains it a little better.
XBG
Nexus1155Dorchester · Jan 2, 2011#157Even if you have a lower wastegate spring, isn't the purpose of a boost controller to only allow the wastegate to crack open once it has reached the desired boost level? So even if you had the spring in with the boost controller attached, you would crack once the boost controller allows the air to flow into the wastegate regardless of whatever spring is in it?
I dunno if I am reading it wrong or am missing something, let me know
cali yarisCanoga Park, CA · Jan 2, 2011#158This is not making sense, sorry.
The spring determines the minimum boost you can run, not the maximum.
The purpose of a boost controller is to run more than that (and get to it faster).
How did you control boost without a wastegate?
The gold spring was only allowing me to get to 5.8 psi before it would shut me down. So in order to make more PSI we took the waste gate out
xbgodThread starterFlorida · Jan 2, 2011#159Yes I understand that too. Which is why I think Tial preinstalled that smaller spring. But my tuner has something else in mind. So off to what ever he deems necessary.
I don't care what he uses as long as I get to 380hp. Which at this point I know I can.
Turning off the VVTI with my system has worked out great. no issues what so ever.
XBG
xbgodThread starterFlorida · Jan 3, 2011#160Hope this clears up the spring issue:
The gold spring I had in the waste gate was a 4.8 and is only good for twice that amount of boost before it cant hold. (about 10psi)
The new combination is a Grey/gold which will hold upto 29psi. but the car must be able to make at a minimum 14.5lb of boost or you will never hold pressure.
Hope this helps peolpe understand a little better.
XBG
cali yarisCanoga Park, CA · Jan 3, 2011#161It doesn't clear it up. Above the spring's rating, the boost controller keeps the wastegate shut until desired boost is reached.
I'll say no more on this, looking forward to your results which I'm sure will be good.
xbgodThread starterFlorida · Jan 3, 2011#162Thats the best I can do for ya Cali. I even talked to the Jake at Tial he said that gold spring would never work either for 28psi. Has to be the grey/ gold to make it happen.
On the other hand.......and this is for Parma..........
Shifter cable was burned right through. 200.00 for a new one. Wrapping the new one in DEI shield and having a aluminum shroud with a heat resistant material from DEI put on the other side of it to also block the heat.
You were right on with your S.W.A.G
XBG
TamagoOff Grid · Jan 3, 2011#163i went through a set of cables after my turbo build too. it was a struggle. toyota put the cables dangerously close to the stock exhaust, and when you upgrade "go bigger" you immediately heat up your stock cables.
good luck Aras (asshole).
Blown_xaVirginia · Jan 3, 2011#164looks like promising results so far. Hey remember i mentioned the wastegate spring a couple weeks ago.... hehe. I remember looking at your build pictures, one thing that is probably causing the creep is the fact your recirculating dump is kinda short and dumps at a perpindicular angle into the downpipe. The exhaust flow from the downpipe may be causing pressure in the dump therefore causing a reverse wastegating effect... boost creep. Worst case run an open dump. Having the wastegate opposite from turbo entry won't help either, but with a top mount log manifold i guess there is no place else for it. Your gonna run a lot of boost anyhow so creep wont really effect u at 30psi. With a proper wastegate spring, you should be able to hold 30psi all the way to redline with that turbo I would imagine.
xbgodThread starterFlorida · Jan 3, 2011#165Your so kind Tamago.....Thanks brother.
And I think your right about that.BlownXA
XBG
cali yarisCanoga Park, CA · Jan 4, 2011#166ooh 30 psi... nom nom nom
Bluevitz-rsOshawa, Ontario, Canada · Jan 4, 2011#167 Originally Posted by
cali yaris ↑ It doesn't clear it up. Above the spring's rating, the boost controller keeps the wastegate shut until desired boost is reached.
I'll say no more on this, looking forward to your results which I'm sure will be good.
The physical pressure inside the exhaust turbine is becoming greater than pressure of the spring before the desired boost level is being reached. So the pressure of the exhaust alone is enough to open the waste gate. No need to add vacuum pressure on the other side of the spring to open it, so no boost controller will ever be able to hold it closed if the there's more pressure inside the exhaust than spring pressure holding the gate shut.
So, desired boost pressure is a combination of exhaust pressure, spring pressure and vacuum pressure. The only one we have control over is vacuum.
ParmasML · Jan 4, 2011#168 Originally Posted by
xbgod ↑ Shifter cable was burned right through. 200.00 for a new one. Wrapping the new one in DEI shield and having a aluminum shroud with a heat resistant material from DEI put on the other side of it to also block the heat.
You were right on with your S.W.A.G
XBG
The trans cables are the only reason I kept the exhaust downpipe at 2.5". If I increased it to 3" I would surely burn a cable every month probably 😠
The yaris engine bay is too compact to go extreme without issues like these...
Did your hood scoop help much in reducing underhood temps?
cali yarisCanoga Park, CA · Jan 4, 2011#170my downpipe is 3", along with the rest of the exhaust. I haven't had any problems with trans cables. Must be a different downpipe shape than you guys have.
xbgodThread starterFlorida · Jan 4, 2011#171Don't know on the hood scoop thing.
when I'm on the dyno my whole front end is off and my hood is open.
Like You Parma my exhaust is 2.5' all the way through as well.
Cable should be in today and new wastegate spring by thursday. Then back at it again.
XBG
ParmasML · Jan 4, 2011#172 Originally Posted by
cali yaris ↑ my downpipe is 3", along with the rest of the exhaust. I haven't had any problems with trans cables. Must be a different downpipe shape than you guys have.
I think your exhaust downpipe is facing towards the left (looking from infront of car) which is opposite to the trans cables and that is probably the reason why you never had such issues. Be happy with that decision, trust me 👍
xbgodThread starterFlorida · Jan 4, 2011#173Well Cable has been reinstalled and DEI heat wrapped along with this fabricated shroud to block the heat. Waiting on the spring to show up for the wastegate.
But in the mean while I went ahead and had the gear oil changed in the tranny. Put back in Amsoil MTGQT 75-90 figured since I was in there may as well start fresh.
Well thats where were at today guys
XBG
TamagoOff Grid · Jan 4, 2011#174how long do you think that transmission is gonna last?
cali yarisCanoga Park, CA · Jan 4, 2011#175^ who knows, mine is holding up well, and Art raced the crap out of his xB at 280 whp.
TamagoOff Grid · Jan 4, 2011#176my 6bolt echo transmission lasted 5 months at 160+ whp :(
cali yarisCanoga Park, CA · Jan 4, 2011#177^ bleh. I'll pray more.
xbgodThread starterFlorida · Jan 5, 2011#178Yeah the trans. Is the weakest link in this car. And with not alot of after market parts available, it is was it is, a time bomb.
I'm using a Fidenza 4.3 clutch and flywheel in this trans and that's about it. Nothing else real special. Should this thing shit the bed I contacted Chris at Kaaz for a new build at their facility. Will use their Lsd and have the gears cryogenicly treated, use the same Fidenza parts let them do all the work and then reinstall. That's about all I'm gonna be able to do and then let it ride.
XBG
Man u must be made of money
ilikericesavannah, ga · Jan 5, 2011#180money trees all over florida, u didnt know?... he probably gots a money tree farm in his back yard i bet..
xbgodThread starterFlorida · Jan 5, 2011#181no I just print more...............Don't you?
The cost actually isn't to bad to do this.
I would just send in my transmission housing along with the new gears that I would buy with my Toyota parts account. (big discount)
Cryo cost = 200.00
LSD = 950.00
Kaaz rebuild to include hand chamfering of all gears = 1,000.00
Fidenza 4.3 clutch = free
Fidenza flywheel = free
so all brand new shit hand chamfered and assembled ready to go = 2,450.00
not to bad for alittle piece of mind. But still no guarantee. But Untill I break this one it will still stay as is.
XBG
You can get slot of Big Macs with that money. You sure you don't wanna buy us all lunch :)
Blown_xaVirginia · Jan 5, 2011#183my trans has over 120,000 miles on it, seen boost since 5000 miles. I don't have traction until 80mph though, I guess when I slap slicks on in the spring ill be clinching my buttcheeks... cause then it will see a lot of load.
xbgodThread starterFlorida · Jan 5, 2011#184You can do just about anything with the right people and money. There aare just not enough tranny guys out there that do high performance race builds on this stuff.
It's not like Crower, Pauter, CP and so fourth that have Pre-made extrusions that they machine into what they want.
You'd have to start from dead scratch with this tranny stuff and be way out in one -off land. And still have someone who is willing to take it on. It would be outragous. Easier to just get a new-used tranny from E-bay for 400.00 and use it till it breaks.
The cost on the other, if you could find some company willing to do it would be thousands. Their is just no demand for it, much like the Ferrea valvetrain. Hince why it's so expensive.
XBG
cali yarisCanoga Park, CA · Jan 5, 2011#185^ You'd also have the challenge of knowing exactly what you wanted to change about it. That would be based on and very specific to what you plan on doing with the car. Autocross, road racing, and drag racing are very different setups in this respect.
xbgodThread starterFlorida · Jan 5, 2011#186Yes, lots to consider. I'll just continue to do what I'm doing or do the build I mentioned above when my shit breaks.
XBG
johnny_vitzHamilton, Canada · Jan 6, 2011#187 Originally Posted by PK198105 ↑
thanks for the answer guys.what about a different tranny other than that from the 1NZFE, how difficult/expensive is it to mate a different tranny to an engine.
ps. Tam no need to be a smartbutt please
Bluevitz has a C160 (6 speed) on his echo, he has a DIY written up.
http://yarisfans.com/forum/yaf_posts...on-Thread.aspx I think the only special tool needed is the "B" puller set
Scubaru Stevecalgary · Jan 6, 2011#188Sweet setup on the xb!
loving the spt coupler 😉
xbgodThread starterFlorida · Jan 8, 2011#189Looks like all is put back together and my new spring rate from Tial is 16.75 for my wastegate, which was decided by my tunner.
Transmission is good to go and custom cable cover and shroud all done. So hopefully no more burn throughs.
So Monday morning it's off to the alignment rack to get me a perfect stance with the right amount of camber and so fourth. As well as I'm tucking the tires as far into the wheel wells as possible. Trying to get me a nasty bad-ass stance. Once that is done back on the Dyno sometime monday afternoon or possibly Tuesday morning depending on dyno situation. Then hopefully some great numbers to show. Can't wait to get through this part to move on to the next step of sheet metal Hull and new K-Sport hand-Brake and new stuff from Sparco. Here are some pics of the new items. Let me know what you think.
XBG
5 attachments not included in this copy
Scubaru Stevecalgary · Jan 8, 2011#190im kinda jelous of the hydraulic handbrake....
H3LlIoNMidatlantic · Jan 8, 2011#191 Originally Posted by
xbgod ↑ I'll just continue to do what I'm doing or do the build I mentioned above when my shit breaks.
XBG
Yeah budday! I bet you rack up a
shitload of miles pulling that thing on and off the trailer. 👍
xbgodThread starterFlorida · Jan 8, 2011#192not really. Car has always been streetable and will still be when finished.
XBG
cali yarisCanoga Park, CA · Jan 9, 2011#193What's the purpose of that handbrake?
xbgodThread starterFlorida · Jan 9, 2011#194Honestly...........just to be different and have something else done that no one else has.
It will just go well with the sheet metal hull. It will take the place of my e-brake and be fully functional.
XBG
Bluevitz-rsOshawa, Ontario, Canada · Jan 9, 2011#195you going to add a second set of callipers on the rear for the e-brake?
xbgodThread starterFlorida · Jan 9, 2011#196no need to. It taps right into my rear brake line. You'll notice there is no resivor for fluid for a seperate set of calipers.
XBG
Bluevitz-rsOshawa, Ontario, Canada · Jan 9, 2011#197so there's some kind of one way valve built in i guess so the fluid doesn't just push back to the master.
jounabayamon puerto rico · Jan 9, 2011#198what are you trying to do with this xb. 1/4 races?. circuit? or just for kicks?
xbgodThread starterFlorida · Jan 9, 2011#199Just one nasty street queen. Don't really have time for any thing else. I can hit shows once in awhile. But I Plan to have the nicest most extreme XB around.
XBG
ilikericesavannah, ga · Jan 9, 2011#200i totally respect the trailer queen scene.. my best friend/old roomate had close to $80k invested (with receipts to prove) in his crx.. i helped with motor issues and interior projects and we used to ride in his suv pulling his crx on a trailer to HIN, TunerBash, and other shows thru out the years.. oh how i miss the smell of spray wax in a convention centers..
I DONT MEAN TO CRASH UR THREAD.. i totally think ur XB is the shit and your doing it right.. hands down total respect 🙇