Yarisworld Archive

Want to build costom turbo kit. Need advice from boosted guys!

610 posts · 163,166 views · page 6 of 13

Replies continued

Bluevitz-rsOshawa, Ontario, Canada · Oct 1, 2010#251
Originally Posted by sleey0 ↑
But the shafts need changed too. I heard they are as thin as a pencil!
Other than "that's what she said", what do you refer to as a "shaft"?
sleey0PA · Oct 1, 2010#252
Cams
cali yarisCanoga Park, CA · Oct 1, 2010#253
cams? thin? 🤷 I thought we were talking about rods and pistons.
sleey0PA · Oct 1, 2010#254
Dont remember who but someone said the camshafts were like pencils.

I dunno....
sleey0PA · Oct 1, 2010#255
You know me carlos!

I do confuse myself sometimes hahaha.
Cant wait to see your finished ride pimpyaris!
sleey0PA · Oct 1, 2010#256
Dumb? But do u have to pull the engine to replace rods and pistons?

Dont kill me guys! 😳
sleey0PA · Oct 1, 2010#257
Thanks, carlos.

I figured that but it never hurts to ask (even though my ego took a hit lol).
1.5tySalisbury nc · Oct 1, 2010#258
sleey0 when you going to get your turbo kit together
pimp my yarisThread starterchicago · Oct 7, 2010#259
Has anyone installed a 255lph fuel pump in the stock pick up assem.? It will obviously need some modification as the larger pump is about an inch longer. So how did U guys install your bomba de gasolina? And a picture would be worth a thousand words.🤷
pimp my yarisThread starterchicago · Oct 10, 2010#260
So I guess no one had any tips or sugestions, so I figured it out for myself. I installed my 255lph fuel pump and got it sealed with new larger sized O-rings into the factory [in tank fuel filter and regulator assem]. I took some pictures along the way. It worked well for about three miles. Unfortunatly I did not buy the name brand Walbro fuel pump. I think I got a Chinese nock off. As soon as it got warm the car would not go over 3K rpm. Then about a mile later it failed completely. I waited 10min and it started again and I barley made it home. Then I swaped back the the factory pump. I will need to order the Walbro pump soon.

I also put a TRD TURBO sticker and a cartoon turbo face sticker on the back for fun. That way when I kick some ass the looser will know why. I showed them to a Audi A8 today after a short stop light gruge match. I also continue to work on tuning with the AEM FIC.

I had a problem with idle quality and sometimes going lean at idle and dying out after driving on the highway for a long time. I watched my air fuel and noticed my factory O2S was very slow to switch when it was hot at idle. I think it may be fried. I disconnected the factory O2 connector and I was still very lean at idle. I then richened the AF with the FIC at lower RPM. Now that the car is in open loop all the time with the O2 dissconnected it is not trying to correct my adjustments. Now I idle at 13.5 to 14:1 AFR instead of 14.7 to 17:1. Of coarse this should be done with the FIC altering the factory O2 signal. But atleast for now she is runing like a dream. I also richened up the mixture under boost as well to around 11.5:1. It runs so much better in open loop and a little richer. And I also feel safer about getting on the gas. I still avoid the very high rpm until I get some larger injectors.
Did I mention how much fun this car is to drive now 🤤

4 attachments not included in this copy

pimp my yarisThread starterchicago · Oct 10, 2010#261
stickers

2 attachments not included in this copy

PETERPOOPOahu · Oct 11, 2010#262
so much for a sleeper...
cali yarisCanoga Park, CA · Oct 11, 2010#263
So I guess no one had any tips or sugestions,
never saw the thread, but glad you got it worked out
sleey0PA · Oct 11, 2010#264
I hope the better pump works for ya.

How much boost are you aiming for?
sleey0PA · Oct 11, 2010#265
Originally Posted by PETERPOOP ↑
so much for a sleeper...
When I am done, mine is DEF gonna be a sleeper.

I don't even have a body kit on mine (maybe next summer) or aftermarket wheels - rolling on steelies!

lol

Sleeper = me👍
Focus_Sh1ftNew Jersey · Oct 11, 2010#266
Glad to see you got that worked out, I really didn't know what to tell you. So, you've decided to keep the car constantly in open loop? I dunno if you've checked my thread, but closed loop is definitely an issue... I was also wondering, since you pulled O2 sensor 2 when you had your exhaust done... Wasn't your car constantly in open loop anyway?
sleey0PA · Oct 11, 2010#267
^^

Yes, that is how one of garms buddies runs open loop constantly. But it come with the price of a constant CE light.
pimp my yarisThread starterchicago · Oct 11, 2010#268
[QUOTE=Focus_Sh1ft;521878]Glad to see you got that worked out, I really didn't know what to tell you. So, you've decided to keep the car constantly in open loop? I dunno if you've checked my thread, but closed loop is definitely an issue... I was also wondering, since you pulled O2 sensor 2 when you had your exhaust done... Wasn't your car constantly in open loop anyway?[/QUOTE

Removing the after cat. O2 wont put you in open loop. But dissconnecting the manafold O2 will. I was still idling lean and had a rough idle after dissconnecting the O2. I added 20% fuel during idle and whenever runing out of boost. Its runing so much smoother now and I feel safer. The correct way would be to modify the O2 with the FIC. This would keep the CEL off. But I have no converter anyway, so it would still be on. Im sure mileage will suffer, but i would rather keep rings and pistons cooler with a richer mixture.
pimp my yarisThread starterchicago · Oct 11, 2010#269
I also had a problem with dying out at idle with a hot engine or when idling for a long time. Its all been taken care of now.
sleey0PA · Oct 11, 2010#270
[QUOTE=pimp my yaris;522037]
Originally Posted by Focus_Sh1ft ↑
Glad to see you got that worked out, I really didn't know what to tell you. So, you've decided to keep the car constantly in open loop? I dunno if you've checked my thread, but closed loop is definitely an issue... I was also wondering, since you pulled O2 sensor 2 when you had your exhaust done... Wasn't your car constantly in open loop anyway?[/QUOTE

Removing the after cat. O2 wont put you in open loop. But dissconnecting the manafold O2 will. I was still idling lean and had a rough idle after dissconnecting the O2. I added 20% fuel during idle and whenever runing out of boost. Its runing so much smoother now and I feel safer. The correct way would be to modify the O2 with the FIC. This would keep the CEL off. But I have no converter anyway, so it would still be on. Im sure mileage will suffer, but i would rather keep rings and pistons cooler with a richer mixture.
Patience.

CTScott is gonna look at it in a few weeks. I bet anything he comes up with some type of workaround🙇

AND a good idea is to start a donation fund for him. The dude has helped nearly everyone on this site lol.

I would def donate to thus project, IF CT wants to set it up.
Nexus1155Dorchester · Oct 12, 2010#272
There is already such a device, it is a narrowband simulator. You obviously need to have a wideband of your own to tune. But once you have the fuel tuned and the wideband still sees 11.* the narrowband simulator will tell the ECU that it is at 14.7 therefore not have the ECU going crazy.

Most in car widebands/managements have the ability to do such a thing. Check it out on most of the spec pages. I beleive both the FI/C the Uego and the emanage can do this, just alot of people never take advantage of it.

That and a MAF clamp, you should be running CEL free.
pimp my yarisThread starterchicago · Oct 23, 2010#273
I took some pics for the micro image calendar. I call this one, In Your Face! I wonder who's phone number is on my license plate?

1 attachment not included in this copy

Dj WaRrIoRPuerto Rico · Oct 29, 2010#274
Originally Posted by pimp my yaris ↑
Has anyone installed a 255lph fuel pump in the stock pick up assem.? It will obviously need some modification as the larger pump is about an inch longer. So how did U guys install your bomba de gasolina? And a picture would be worth a thousand words.🤷
ok i went throught that experience.. i had a shop do this for me cuz wen i came to fuel i didnt want to blow up lolll.. what they did was easy.. the litterally shaved off the fuel filter to disconnect the stock regulator... after that they splited up the line goin to the engine.."T" ok so you have a 3 way splitter right on one end the walbro at the opposite end the line going to the canister leading to the engine.. and on the other side left the fuel regulator ..that did 188WHP @8psi for me with stock internals and returnless fuel system...
pimp my yarisThread starterchicago · Nov 2, 2010#275
I recently have noticed a small problem with my cheap turbo. When the car sits overnight and U first start it up in the morning. If I just let it idle and warm up for a while I will get some white smoke coming from my exhaust when the engine starts to warm up. If I rev it up I get a little cloud of smoke. Once I start driving the smoke is gone and no more problem. I have removed my downpipe and have noticed some oil leaking from the turbo into the exhaust when the car sits and gets cold. I have also checked my oil level regularly and never noticed any oil burning issue. Even making 800mile trip there was no oil loss.
So I think its only a drop or two that leaks into the exhaust every night. It just really pisses me off though. I have done everything to prevent this. My coolant lines are connected and I have a turbo timer.
I guess thats what U get for buying the cheap Chinese turbo. I hope it holds up through winter and mabe I will get a Garret next summer. Its 950$ compared to the 240$ I spent for my turbo.
I wonder if I had a converter, mabe that would eliminate the smoke?
pimp my yarisThread starterchicago · Nov 2, 2010#276
Originally Posted by Dj WaRrIoR ↑
ok i went throught that experience.. i had a shop do this for me cuz wen i came to fuel i didnt want to blow up lolll.. what they did was easy.. the litterally shaved off the fuel filter to disconnect the stock regulator... after that they splited up the line goin to the engine.."T" ok so you have a 3 way splitter right on one end the walbro at the opposite end the line going to the canister leading to the engine.. and on the other side left the fuel regulator ..that did 188WHP @8psi for me with stock internals and returnless fuel system...
Thanks for the tip. I didnt think of that.
Focus_Sh1ftNew Jersey · Nov 2, 2010#277
Originally Posted by pimp my yaris ↑
I recently have noticed a small problem with my cheap turbo. When the car sits overnight and U first start it up in the morning. If I just let it idle and warm up for a while I will get some white smoke coming from my exhaust when the engine starts to warm up. If I rev it up I get a little cloud of smoke. Once I start driving the smoke is gone and no more problem. I have removed my downpipe and have noticed some oil leaking from the turbo into the exhaust when the car sits and gets cold. I have also checked my oil level regularly and never noticed any oil burning issue. Even making 800mile trip there was no oil loss.
So I think its only a drop or two that leaks into the exhaust every night. It just really pisses me off though. I have done everything to prevent this. My coolant lines are connected and I have a turbo timer.
I guess thats what U get for buying the cheap Chinese turbo. I hope it holds up through winter and mabe I will get a Garret next summer. Its 950$ compared to the 240$ I spent for my turbo.
I wonder if I had a converter, mabe that would eliminate the smoke?
Yeah, doesn't seem like it's THAT big of a deal. I'm still dripping oil a bit, but it's like your case where the amount is so insignificant that its not even effecting oil level.

And let's be real here, your install went wayyyy too good regarding leaks until now lol.
Dj WaRrIoRPuerto Rico · Nov 4, 2010#278
Originally Posted by pimp my yaris ↑
Thanks for the tip. I didnt think of that.
no prob believe me i've been through ALOOOTT i haven't even read here... just so you know i turbocharged my sedan BY MYSELF so i made ALOT of noobie mistakes like not connecting the blow-off valve to vacumm just boost 😆 but now i took out my motor and reaaallyyy build it by myself with forged internals👍 after 2 weeks trying i cranked it up yesterday now to set the idle rpm and the break-in period and then dynoooo!!! loll

ok.. back to you... about the lil oil problem yes i bought 3 cheap turbos and they leaked a lot but it was another problem.. but doing my research, talking to ppl.. i found out a great way to eliminate that... i dont know if youll understand but it is an "oil-restrictor" have you seen a NOS jet (yes, nitrous)?? i bought a nos jet adapter 1/8 npt and bought a i think it was a 45cc jet i don really remember and that lowers the volume and oil pressure going through the turbocharger thus not pushing oil to the sides thus leaking to your hot side of the turbocharger.... you just install the adapter on either end of the oil feed line.....in other words going from a burger king straw to a chinese rest. straw looolll......😁let me know if you understood...
weapon5MN · Nov 4, 2010#279
Originally Posted by pimp my yaris ↑
I want to build a costom turbo setup using mostly E-bay parts. I am thinking t25/28 turbo. I have found exhaust manafold/turbo, intercooler and piping,oil and water lines if needed. Also a air intake and filter to mount the mass air sensor. I am sure I will need to buy at least 1 more intercooler piping kit and a blow off valve. And I found a downpipe witch will need to be costomized from a nissan silvia. Or I will need a complete costom downpipe.

My questions are what piggy back system should I use to control injector pulse? Will I need bigger injectors right away? I am only looking for 150-170whp. Also should oil source for turbo be tapped from oil pressure sensor or do I need to buy adapter to tap near the filter? I am also sure a new clutch will be in my future shortly after install. I am thinking center force dual friction.
Also can I tune a piggy back system with a lap top and a wide band o2s or do you need some specialized training to complete this. I am a ase master tech for about 12 years, but I have never done tuning. Its just so dame expensive around Chicago. Very few places to go.🤷
that turbo kit is ebay so i would suggest spend more cause that turbo kit is 👎 but like i said is up to you. FYI for a good turbo kit and to save you the time and money get a real kit which are around 3k :D
Bluevitz-rsOshawa, Ontario, Canada · Nov 4, 2010#280
Originally Posted by weapon5 ↑
that turbo kit is ebay so i would suggest spend more cause that turbo kit is 👎 but like i said is up to you. FYI for a good turbo kit and to save you the time and money get a real kit which are around 3k :D
HAHA, wow, he's already built the turbo and is in the tuning process now.
cali yarisCanoga Park, CA · Nov 4, 2010#281
.... make sure you are idling your motor for a minute or two before shutting it down, to let the oil cool a bit and drain. Especially if you're not using water lines to keep it cool during operation.
pimp my yarisThread starterchicago · Nov 5, 2010#282
Originally Posted by Bluevitz-rs ↑
HAHA, wow, he's already built the turbo and is in the tuning process now.
Ya I guess he missed the previous 17 pages.
pimp my yarisThread starterchicago · Nov 7, 2010#283
Originally Posted by Dj WaRrIoR ↑
no prob believe me i've been through ALOOOTT i haven't even read here... just so you know i turbocharged my sedan BY MYSELF so i made ALOT of noobie mistakes like not connecting the blow-off valve to vacumm just boost 😆 but now i took out my motor and reaaallyyy build it by myself with forged internals👍 after 2 weeks trying i cranked it up yesterday now to set the idle rpm and the break-in period and then dynoooo!!! loll

ok.. back to you... about the lil oil problem yes i bought 3 cheap turbos and they leaked a lot but it was another problem.. but doing my research, talking to ppl.. i found out a great way to eliminate that... i dont know if youll understand but it is an "oil-restrictor" have you seen a NOS jet (yes, nitrous)?? i bought a nos jet adapter 1/8 npt and bought a i think it was a 45cc jet i don really remember and that lowers the volume and oil pressure going through the turbocharger thus not pushing oil to the sides thus leaking to your hot side of the turbocharger.... you just install the adapter on either end of the oil feed line.....in other words going from a burger king straw to a chinese rest. straw looolll......😁let me know if you understood...
I have a 1.5mm oil restrictor on my feed line. This was recomended for a journal bearing turbo. Ball bearing turbos use 1.0mm restrictor. So I know thats not my problem. I am sure the oil seal on the hot side is leaking oil into the exhaust. I am just debating if I should buy another GT25 nock off like I have now for 240$ and take my chances. Or buy a Garret gt2554r genuine artical for 1000$. Oh ya did I mention I'm poor and for me 1000$ is a lot of FLOW!😢
Bluevitz-rsOshawa, Ontario, Canada · Nov 7, 2010#284
I'd find out if there's any shaft play first. If it's fine, I'd just re+re the seals and have another go at it. It's your cheapest option.
pimp my yarisThread starterchicago · Nov 8, 2010#285
Originally Posted by Bluevitz-rs ↑
I'd find out if there's any shaft play first. If it's fine, I'd just re+re the seals and have another go at it. It's your cheapest option.
I checked the shaft play when I had the downpipe off last. It was OK. I'm not sure what [re+re] means. I am assuming that is canadian secret code for replace, LOL😁. I would love to replace the seal. I dont know where I could get a oil seal for some chinese nock off turbo though. I could not even read the hyroglifics on the box. If you have any ideas ??? let me know.
cali yarisCanoga Park, CA · Nov 8, 2010#286
re+re = repair and replace
Bluevitz-rsOshawa, Ontario, Canada · Nov 8, 2010#287
Well, I'd say that if it's a GT25 knock-off chances are a seal for real GT25 would work. It'd be worth a shot if it's only a few bucks.

Oh, and my version of re+re is remove and replace.
Focus_Sh1ftNew Jersey · Nov 9, 2010#288
Out of curiosity, does the turbo need to be rebalanced if the seals are replaced?

I may be looking at doing the same thing unfortunately. I've been finding oil in the coupler where my BOV is. Could be left over, but I dunno 🤷
YodaFL · Nov 9, 2010#289
Clean it and see if it comes back
Dj WaRrIoRPuerto Rico · Nov 10, 2010#290
ok about re+re it ok but the tip is to mark the position of the nut with the axle so you know till what point adjust the nut so you would hold 95% of the balance when puting it back together..i did this with a file or if you want do it with a sharpie BUT DONT ERASE IT WHILE CLEANING!! but yes buy the seals of ebay if your knock off doesnt not have water lines (hibrid) look for dry turbo rebuild kit for your specific turbocharger.. mine was to3 but i dont know yours.. but important DRY!!! NOT wet because you dont have water lines goind through.. if you do that you can get a little more out of your knock off till you get some money for a real one.. and BTW i converted a cheap knock off into a 99.9% garret.. how? well we have a shop here that changed everything except my hot housing cuz i already had the cheap flange (4 bolt) for the down pipe.. it cost me around $300 and he even converte it to garret hybrid (wet) and believe me it is a real garret allaround ! compare 1,000 to 300 !! 😈 if you want here's his email...gigitoturbo@aol.com http://stores.ebay.com/Yiyito-Turbo-Service i know it is here in puerto rico but he has an ebay account too and i know for a fact he doesn't have a problem with shipping things.. so if you are interested send him an email explaining what you have and if you have that option of converting it and for how much..
weapon5MN · Nov 12, 2010#291
Originally Posted by Bluevitz-rs ↑
HAHA, wow, he's already built the turbo and is in the tuning process now.
yea very late didn't know it went on this long 🤷
pimp my yarisThread starterchicago · Nov 28, 2010#292
OK I finally did some work to eliminate my smoke problem on cold engine starts. The problem has been getting progressivly worse as the weather gets colder. Their has been a lot of talk about where the oil return enters the pan. I dont believe that is the problem. But I admit its a possibility. My oil return was submerged in oil in the lower part of the pan. So this weekend I removed the right side axel and relocated the return to the top of the pan above the oil level. I also switched from a 1/4npt fitting and a 3/8in hose to a more free flowing 3/8npt fitting and a 1/2in hose. The thing is huge. For sure if I continue to have a cold start smoke problem, I know it will not be the return. I have finished the work and just need to fill with fluids tomarrow after my silicone drys on my oil pan. I will also take a pic. tomarrow.
Focus_Sh1ftNew Jersey · Nov 28, 2010#293
Originally Posted by pimp my yaris ↑
OK I finally did some work to eliminate my smoke problem on cold engine starts. The problem has been getting progressivly worse as the weather gets colder. Their has been a lot of talk about where the oil return enters the pan. I dont believe that is the problem. But I admit its a possibility. My oil return was submerged in oil in the lower part of the pan. So this weekend I removed the right side axel and relocated the return to the top of the pan above the oil level. I also switched from a 1/4npt fitting and a 3/8in hose to a more free flowing 3/8npt fitting and a 1/2in hose. The thing is huge. For sure if I continue to have a cold start smoke problem, I know it will not be the return. I have finished the work and just need to fill with fluids tomarrow after my silicone drys on my oil pan. I will also take a pic. tomarrow.
When you say 1/2in hose, do you mean a -8 AN line? The first thing I was thinking about doing was increasing the size of the line.

Also, since we tuned the same way - are you noticing irregularities in your map? For example, now that it's cold and my IAT is hovering around 30F, I've noticed my AFRs have richened by as much as a whole point. I'm thinking colder IATs force the ECU to change the open loop maps slightly. It may not even be the IATs, but I had perfectly accurate AFRs until it got REALLY cold the last week.
cali yarisCanoga Park, CA · Nov 29, 2010#294
pimp, you changed the location AND the size? I think it will be hard to tell which change fixed the problem.
pimp my yarisThread starterchicago · Nov 29, 2010#295
Well so far so good. I have only started the car once after the repair but so far no smoke. I will know more after I start my car to go home from work at 10pm. If this is all I needed I will be so happy. I was ready to throw down $915 for a garrett GT2554R. I thought the oil seals were bad on my turbo. The turbo I am using works great and spools really fast. The only problem I had was the smokey exhaust.
I would much rather use the cash for a vacation to Mexico 😁

O' ya this is the artical reguarding oil drains, I read when shopping for garrett turbos on their web site. Very informative. And thanks Cdydjded for bringing this up when we talked.

OIL LEAKAGE SHOULD NOT OCCUR ON A PROPERLY FUNCTIONING
SYSTEM IF RESTRICTOR IS NOT USED UNLESS THE SYSTEM
PRESSURE IS EXCESSIVELY HIGH.

Oil Drain
In general, the larger the oil drain, the better. However, a -10AN is typically sufficient
for proper oil drainage, but try not to have an inner diameter smaller than the drain hole
in the housing as this will likely cause the oil to back up in the center housing. Speaking
of oil backing up in the center housing, a gravity feed needs to be just that! The oil
outlet should follow the direction of gravity +/-35° when installed in the vehicle on level
ground. If a gravity feed is not possible, a scavenge pump should be used to insure that
oil flows freely away from the center housing.
Avoid:

■Undulations in the line or extended lengths parallel to the ground
■Draining into oil pan below oil level
■Dead heading into a component behind the oil pan
■Area behind the oil pan (windage tray window) where oil sling occurs from crankshaft

When installing your turbocharger, insure that the turbocharger axis of rotation is parallel
to the level ground within +/- 15°. This means that the oil inlet/outlet should be within
15° of being perpendicular to level ground.
pimp my yarisThread starterchicago · Nov 29, 2010#296
My computer cuts fuel at 115mph. Its like hitting a brick wall. Has anyone bypassed this problem yet. I want to pin this speedo 😲
pimp my yarisThread starterchicago · Nov 30, 2010#297
I can now say for sure my problem is fixed. No more smoking out my neighbors while my car warms up. And my co-workers cant call my Yaris a bug fogger any more. Glad it was a easy fix.
Focus_Sh1ftNew Jersey · Nov 30, 2010#298
Originally Posted by pimp my yaris ↑
I can now say for sure my problem is fixed. No more smoking out my neighbors while my car warms up. And my co-workers cant call my Yaris a bug fogger any more. Glad it was a easy fix.
Awesome. I'm gonna follow suite when the semester ends.

How's your tune holding up though? I'm still having weird richening problems.
pimp my yarisThread starterchicago · Nov 30, 2010#299
Pics😁 Old location of drain is the brass plug

2 attachments not included in this copy

pimp my yarisThread starterchicago · Nov 30, 2010#300
[QUOTE=Focus_Sh1ft;537902]Awesome. I'm gonna follow suite when the semester ends.

How's your tune holding up though? I'm still having weird richening problems.[/QUOTE
The oil line may be causing your oil in the intake problem. My tune is working ok, but I still need to get some bigger injectors. I always shift early to avoid going to lean.