Replies continued
pimp my yarisThread starterchicago · Jul 18, 2010#51Well I couldn't wait till wed. Today I mounted it up and checked for clearance. It fits but its very close. The wastegate acuator bracket is about 1/4 inch away from the firewall. I may need to pound it back just a touch. But the engine torque should pull the engine down and away when on the gas. I also needed to reclock the compressor housing so the discharge was not so close to the engine block. Then I needed to drill and tap a small hole in the compressor housing for the wastegate actuator. Its now adjusted so the discharge is aimed straight down for easy attachment of intercooler pipe. Took some pics to. Now I need mo money🙁 Next update in 2-3 weeks.
5 attachments not included in this copy
Nexus1155Dorchester · Jul 19, 2010#52 Then I needed to drill and tap a small hole in the compressor housing for the wastegate actuator
Why? Thats what that 90* brass elbow is for that the wastegate actuator was connected to in the first place, is a boost pickup line.
Most of them OEM have them on the housing, but aftermarket chinese units have them on the compressor outlet.... Serves the same purpose.
Engine flexes every which way, not only forwards. and especially when you hit rev limiter, it will shake like a mother. Make sure there is enough room so nothing gets crushed. 1/4" is pretty damn close. Read and take in my suggestions in the last post i made before yours too, I am sure everyone else will concur as well.
pimp my yarisThread starterchicago · Jul 19, 2010#53Nexus1155 Reclocking the turbo involves changing the direction of the air discharge on the compressor housing. when the turbo was mounted the discharge was less then an inch from the engine block. In the pictures U can see now it is straight down and aimed between the axel and subframe. The hole needed to be drilled because the actuator can not be moved. It must be across from the wastgate. Their were some extra holes drilled in the compresser housing to reclock but not enough. You can see extra holes in the picture. You can also see the mark where I drilled the additional hole. If you look at pics of turbo U can see discharge is about 90 degrees different. As far as the clearance goes I said I may need to bend firewall back slighltly if it makes contact. If you use external wastegate there would be plenty of clearance but the downpipe would be more complicated.
4 attachments not included in this copy
Nexus1155Dorchester · Jul 19, 2010#54I see what you mean from those pics, but you can always go to the auto store and get a longer hose and reroute the line, or tap in a MBC up to your engine compartment so you do not get wastegate flutter.
Anyways, the easiest solution is the one not involving fabrication work.....but I am glad to see youre getting things mocked up already.
If you are worry about the heat, you can always get some heat resistant tube wrap, i used them on my wastegate lines as well from being so close to the manifold, but the line can usually handle anything thats not touchign manifold or turbo hot side
pimp my yarisThread starterchicago · Jul 19, 2010#55Ya I may try a mbc later. Its already a 8psi actuator. Thats gonna be pushing it for a stock motor. I think I will use some header wrap for the down pipe. And mabe another piece of sheet metal between the turbo and fire wall. The only thing close to the turbo is the brake line that runs to the passenger side front wheel.
pimp my yarisThread starterchicago · Aug 8, 2010#56Update: I ordered a front mount intercooler and 2.25" piping kit and also an additional piping kit as well and a adjustable bov that can be piped to recirculate. And a oil feed line with t fitting to tap into pressure sensor. This size should work well. My turbo,T/B and air box should fit 2.25" silicone connectors. I am going to try to use the stock air box and mass air. It may cause problems with fitting intercooler piping later though. I also have a question guys> Where are you tapping into to get your coolant for the water lines on the turbo?? I am thinking heater core lines would be the most obvious choice. But Im not positive.
If anyone is intrested, so far I spent 876.99$ including shipping
4 attachments not included in this copy
wow you dont waist much time do you. looks nice its coming together
cali yarisCanoga Park, CA · Aug 8, 2010#58heater core lines will work fine. I have to check mine, I thing we used one in a different place that was available off the block.
cali yarisCanoga Park, CA · Aug 8, 2010#59If the turbo has water line inlets/outlets, use them! -- I love not needing a turbo timer or to have to sit there for 30 seconds idling before I jump out of the car.
So there you go, two opinions to consider. 😆
Nexus1155Dorchester · Aug 8, 2010#60 IMO you do not have to flow coolant through the turbo.
Malarky!, the shaft of the turbo is still spinning like 1,000,000 mph like a speeding bullet you want to keep it cooled down. If the turbo has useable ports for water cooling, use them as alot of the heat is transfered into the coolant and pulls it away.
Focus_Sh1ftNew Jersey · Aug 8, 2010#61Race you to be the first to finish their build. 👍
cali yarisCanoga Park, CA · Aug 8, 2010#62^ I win.
^that might work actually
pimp my yarisThread starterchicago · Aug 9, 2010#64 Originally Posted by
Focus_Sh1ft ↑ Race you to be the first to finish their build. 👍
Its on! I hope to be runing sometime in october.
pimp my yarisThread starterchicago · Aug 9, 2010#65 Originally Posted by cdydjded ↑
2.25" is correct on the I/C pipe size. You will not be able to use the stock air box, it wont be able to be pressurized. IMO you do not have to flow coolant through the turbo.
I am planing on putting the mass air before the turbo. That way I can hopefully use stock air box and cut down on costs.
pimp my yarisThread starterchicago · Aug 9, 2010#66 Originally Posted by cdydjded ↑
pimp: I would suggest to use the coolant lines that run through the throttle body if you are going to run coolant lines through the turbo
Thanks for the idea. I think that will be much easier then the heater lines. I dont want to restrict those lines, it gets to dam cold here in winter!
pimp my yarisThread starterchicago · Aug 9, 2010#67Well I just picked up some used 1ZZ injectors that were for sale on E-bay. If anyone was thinking about picking them up, TO LATE I got um! New total 939.49
DezodWestern NY · Aug 9, 2010#68I liked the GT2252 on this motor. Throttle response was there and it made for a nice power band.
DezodWestern NY · Aug 9, 2010#69I also might have gone with a 2" IC pipe on this engine with low boost and 2.25" for anything over say a bar of boost.
pimp my yarisThread starterchicago · Aug 10, 2010#70 Originally Posted by cdydjded ↑
Were you planning to use the AEM FIC?
Yes, also gonna pick up a AEM wideband 02
ParmasML · Aug 11, 2010#71 Originally Posted by
pimp my yaris ↑ Well I just picked up some used 1ZZ injectors that were for sale on E-bay. If anyone was thinking about picking them up, TO LATE I got um! New total 939.49
Bad for you I have a set of these for sale for much less 😁
The Aem is a good choice but an expensive one although you would be happy with it.
I think that intercooler is good for now but if you are thinking of more boost later on you will regret you didn't bought one better.
Don't rush out and do think before you act. Getting the right parts now is an investment for the future and you would not regret the time spent for research!
Good luck!
pimp my yarisThread starterchicago · Aug 11, 2010#72 Originally Posted by
Parmas ↑ Bad for you I have a set of these for sale for much less 😁
The Aem is a good choice but an expensive one although you would be happy with it.
I think that intercooler is good for now but if you are thinking of more boost later on you will regret you didn't bought one better.
Don't rush out and do think before you act. Getting the right parts now is an investment for the future and you would not regret the time spent for research!
Good luck!
I bought used injectors off ebay for 62.00$ with shipping. 939$ is total for eveything I spent so far including Turbo, manafold, intercooler, two piping kits, oil&coolant lines. Still need to buy AEM fic, AEM widebend, stai less pipe for downpipe and exhaust output flange for gt25 turbo. O ya I need more Flow$. Any one got donations🤷
Nexus1155Dorchester · Aug 11, 2010#73The AEM UEGO is a hunk of crap but im sure it will integrate well with the AEM FIC which is always a plus. Parmas, I doubt he will build his car to handle extreme boost, that FMIC will do him good for any boost he needs to push on that turbo.
Oversizing the intercooler and piping for it, and for exhaust in the car is a common mistake alot of people make.
Nexus1155Dorchester · Aug 11, 2010#74Just personal opinion. I've installed Zeitronix, AEM, Innovate LC1 and the Innovate LM-1 is my favorite so far.
Pic doesnt want to load up about the Wideband shootout so just click link i guess!
http://www.fordmuscle.com/archives/2...s/chart_lg.jpg Picture not included in this copy cali yarisCanoga Park, CA · Aug 11, 2010#75There is no LM-1 on the Innovate website, unless i just missed it. Can you point us at the product please?
Nexus1155Dorchester · Aug 11, 2010#76pimp my yarisThread starterchicago · Aug 13, 2010#77Good day today. I got my intercooler and pipe kits,bov,oil feed and water line kit. Also recieved 1zz injectors from a used 99 corolla. Took some pics as I am just starting to mount intercooler. Looks like I may need to ditch my fog lights as they might interfere with piping.😢
5 attachments not included in this copy
Nexus1155Dorchester · Aug 13, 2010#78Hope you are going to get some angle brackets to secure that FMIC to the bumper support..... jus sayin!
Good progress so far though!!!
pimp my yarisThread starterchicago · Aug 14, 2010#79Got some more work done today.
5 attachments not included in this copy
pimp my yarisThread starterchicago · Aug 14, 2010#80With bumper cover
1 attachment not included in this copy
Focus_Sh1ftNew Jersey · Aug 14, 2010#81So you pretty much have the piping done, I'm assuming you're doing the manifold and turbo last-ish? Funny, because I was going to start from the manifold and work my way through.
Either way, your setup is coming along nicely. 👍
ALSO, lemme know how the 1ZZ injectors go for you. I'm having a hell of a time with mine currently.
Nexus1155Dorchester · Aug 14, 2010#82Whats the issue you are having with the injectors? I know a user shaved part of his head? or something to get them to fit easier? I still never seen the intercooler bolted to anything? Don't just let it free hang....
BTW you are a machine with getting things done, remind me of myself. I go into my shop today and spend 5hrs and i just gotta put my engine back in my car. The more organized the quicker you can go through things!
pimp my yarisThread starterchicago · Aug 15, 2010#83I/C is bolted tight, top and bottom. Bumper bar is some crazy hard steel. Dulled about six drill bits getting through. I even went out and bought the best carbid bit I could find and that bumper steel trashed it after drilling one hole. Very frustrsting, but finished with that!
Nexus1155Dorchester · Aug 15, 2010#84nice!, yeah in most instances its easier to drill a pilot hole then use a stepper bit with some type of oil to cut through the steel easier. Or atleast start small and go up gradually in drill bit sizes. I've had to drill 1/2 holes through two inch thick metal with a hand drill because the drill press wasnt powerful enough. I am sure you had the drill kick back at you a few times :P
pimp my yarisThread starterchicago · Aug 16, 2010#85More work today. More pictures. Piping intercooler to turbo. And Turbo intake to air filter/mass air. I think because of space constrants and wanting to keep the intake tract as free flowing as possible. I will not be able to use the stock air box. It just takes up to much space. I cant wait to drive this thing already!!!!
5 attachments not included in this copy
pimp my yarisThread starterchicago · Aug 16, 2010#86I also thought the turbo wastgate actuator might be rubbing firewall after previous test install. But after removing the heat insulation I have a good 1/2 inch or so of clearance. I will also fabricate a sheet metal heat sheild around turbo exhaust housing. I hope the pics are helpful to those who might be thinking about trying this themselves. So far its been a lot of fun and I am happy the way everything has turned out. This car is very mechanic friendly for the most part.
3 attachments not included in this copy
cali yarisCanoga Park, CA · Aug 16, 2010#87Are you going to coat the exhaust mani or just leave it?
Focus_Sh1ftNew Jersey · Aug 16, 2010#88👏
Coming along VERY nicely.
pimp my yarisThread starterchicago · Aug 16, 2010#89 Originally Posted by
cali yaris ↑ Are you going to coat the exhaust mani or just leave it?
I was going to leave it be for now. Not worried about corrosion that mani is pretty heavy duty. Im sure it will long outlast the rest of the car.
pimp my yarisThread starterchicago · Aug 17, 2010#90Tryed to attach coolant tubes and oil feed line today. Found the banjo bolt for the oil feed had the wrong thread pitch. So I ordered a new banjo bolt kit and some stainless pipes and stainless flex bellows for downpipe fabrication.
Nexus1155Dorchester · Aug 17, 2010#91On crush washers, this is a common mistake, we also have a shaved edged 17/19. I don't know what size your botls are, or if they are easily accesible but crush washers are meant to be crushed essentially. Should be as tight as your wrist at full force... any tighter youll snap the banjo bolt clean in half..... don't ask how i know. 🤣
Being where that turbo is, Garm is right, getting some turbo X paint for the hotside and manifold isnt a bad idea when that thing starts to heat up nice and good.
ParmasML · Aug 18, 2010#92Since you are updating much you seem very keen doing this setup as good as possible so here are my recommendations:
1. Take a breath and remove the manifold again and coat it with DEI HT Silicone coating
2. After the manifold is coated, wrap it with an exhaust wrap to decrease heat as possible (which is equal to some more bhp!) Link
http://www.designengineering.com/cat...ps-accessories 3. The wastegate is too close to the firewall and removing the insulation isn't enough. I recommend that you install a solid rear mount or else upgrade it. You will surely have issues of cracking your manifold or damage your wastegate if you will not make this upgrade trust me.
As an option use some anti-rust on that shafts or else replace them and coat them. Rust tend to decrease torsion forces and turbo tends to increase them which is not proportional
Cheers
pimp my yarisThread starterchicago · Aug 18, 2010#93Yesterday I stoped by my friends machine shop and had him make a exhaust flange for my turbo. It may not look glamorous but it saved me 70$. Now I need to weld a downpipe to this bad boy.
2 attachments not included in this copy
Nexus1155Dorchester · Aug 18, 2010#94How thick is that metal? I mean, yes, now cut a hole for the wastegate as well.... You can use a larger pipe that matches the size of the outlet. Probably 2.5" then you can use some smaller pipe for the wastegate and meet up with the downpipe 12" down the piping.
And Parmas is right, your actuator arm is too close. If your engine bucks a bit you might end up slamming that against the wall.
pimp my yarisThread starterchicago · Aug 19, 2010#95 Originally Posted by
Nexus1155 ↑ How thick is that metal? I mean, yes, now cut a hole for the wastegate as well.... You can use a larger pipe that matches the size of the outlet. Probably 2.5" then you can use some smaller pipe for the wastegate and meet up with the downpipe 12" down the piping.
And Parmas is right, your actuator arm is too close. If your engine bucks a bit you might end up slamming that against the wall.
That metal is 1/4" thick steel. You cant see in the picture but there is a cutout inside the turbo housing for wastgate gases to reach that hole. In order to complete this downpipe a tight 180 degree pipe is needed at the turbo exit. Then a 90 is needed to direct gas tward the back. This would be a extremely difficult design for a divorced downpipe. It is also not nessesary for the low boost I will be running. If ever I install upgraded pistons and rods for more boost, I will need a new downpipe design. I am sure I will be able to reach my 160-180whp with this design. And I saved money. If you look at Focus Sh1ft's thread on the last page. You will see the zage downpipe is similar design to what I am making. There dyno test netted 180whp. At least thats what they claim on there U tube video. I have also milled some material away from the inside of the plate where the waste gate opens. This will insure it opens completely and does not make contact. Something I doubt zage did with there flange.
I have also pushed my firewall back to gain additional clearance between firewall and W/G actuator. There is still clearance between my firewall and heat/ac plenium if your wondering. I checked.😁
cali yarisCanoga Park, CA · Aug 19, 2010#96trans mount would be a good idea to limit engine movement, it's a fairly cheap addition.
Nexus1155Dorchester · Aug 19, 2010#97Ah ok I was afraid there might have been some interference or the gasses would not flow properly and you might have issues with wastegate gasses. But it seems like you got it under control.
Yeah I saw the Zage downpipe, although pretty nice looking, I don't like when they don't use the full shape of the turbo outlet. I never really liked that outlet to begin with, but alot of turbos come with them. I liked my K16 outlet the most of any turbo. Big circle with with bolt holes in the 4 corners.
pimp my yarisThread starterchicago · Aug 21, 2010#98 Originally Posted by
Nexus1155 ↑ Ah ok I was afraid there might have been some interference or the gasses would not flow properly and you might have issues with wastegate gasses. But it seems like you got it under control.
Yeah I saw the Zage downpipe, although pretty nice looking, I don't like when they don't use the full shape of the turbo outlet. I never really liked that outlet to begin with, but alot of turbos come with them. I liked my K16 outlet the most of any turbo. Big circle with with bolt holes in the 4 corners.
Ya I kind of agree. I am not really liking this design, but I am getting tight on cash for now and am very anxious to get her running. I have allready found a different flange with a much better free flow into a 3" pipe with V-clamp. But this will have to do for now. I need to leave something to upgrade later.
pimp my yarisThread starterchicago · Aug 22, 2010#99OK update. I had to buy a few miscellaneous parts to complete oil return line and oil feed line. Some of the parts included in the water and oil line kit did not fit because this is not an original ball bearing garett GT25, its a journal bearing nock off. Also wanted a 90 degree fitting for oil pan to insure return line does not rub on anything and to keep it clean. And also ordered first parts not from E-bay. I needed some stainless U bend pipe and a L bend pipe, plus a stainless flex pipe, 'to account for engine flex' this should be all I need to complete down pipe. I ordered these from a web sight call APTUNNING.net, They have a good suply of parts for doing costom work. Oil feed is a -4an line and return is a -6an. Also bought a cold air intake to hack apart and use inplace of factory air box. And I picked up some o2 sensor bungs for factory o2s and wideband.
I see the end is in sight. I still need a aem fic and wideband. Once again I am out of cash and waiting for next paycheck.😢
5 attachments not included in this copy
Focus_Sh1ftNew Jersey · Aug 22, 2010#100What I find interesting is that company, like Zage, also uses that wacky loop bolt with the holes to feed oil to the turbo. Common sense says its a sucky design in my opinion, I wonder why it's so popular? 🤷
Oh, and I feel this is appropriate.
Jersey > Chi-town
😛