Yes thats the plan. And I definitly need the external wastegate. The internal gate does not move fast enough when cranking up the boost.Originally Posted by Scubaru Steve ↑the higher a/r will easily add top end and help increase boost, you will lose spool, as in it will take a few more revs to spool the turbo.
id go with a .63.
Want to build costom turbo kit. Need advice from boosted guys!
610 posts · 163,166 views · page 12 of 13
Replies continued
That's closer to my set up -- you'll love it.
I am having trouble tuning for above 16psi with my FIC. I believe it is ignition problem. Above 16psi I am getting a nasty missfire between 3500 and 4500 where my boost is getting to 18-19 psi. Still working on it, I havent givin up yet. I will try to retard timing a little more at high boost to resolve this. Any tuners out there run into this? I noticed that tuning with the FIC is getting tough as boost climbs. My AFR's are fluctuating a lot within the same cell on my fuel map.
has anyone else ever gone this far with an FIC? 16psi is starting to get pretty serious.
Or try some simple things like close the gap up a thou or two on the plugs
Or try some simple things like close the gap up a thou or two on the plugs
pimp, what gap are you using, and which plugs?
I am running NGK BKR7E plugs gapped at .020"
Have you tried a bigger gap? .020" is getting pretty small compared to the stock at what, 32 thou? It's possible the spark isn't big enough to ignite the mixture properly
you got to stabilize you AFR. give it some more fuel make run 11.0-10.5 AFR then work your way back. you should not be misfiring like that if you have the proper fuel deleavery system in you car.Originally Posted by pimp my yaris ↑I am having trouble tuning for above 16psi with my FIC. I believe it is ignition problem. Above 16psi I am getting a nasty missfire between 3500 and 4500 where my boost is getting to 18-19 psi. Still working on it, I havent givin up yet. I will try to retard timing a little more at high boost to resolve this. Any tuners out there run into this? I noticed that tuning with the FIC is getting tough as boost climbs. My AFR's are fluctuating a lot within the same cell on my fuel map.
So Brian raises a good question at least from a curiosity standpoint...how many PSI of boost is the AEM FIC supposedly good for?
The on-board map sensor is good for ~22psi.Originally Posted by fnkngrv ↑So Brian raises a good question at least from a curiosity standpoint...how many PSI of boost is the AEM FIC supposedly good for?
MAP or MAF?Originally Posted by Yoda ↑The on-board map sensor is good for ~22psi.
The AEM has a built in MAP sensor
Pimp...I thought you were standalone man its crazy a fic at that boost haha looks like it works pretty great for just a piggyback...
you make me double think about going standalone...
you make me double think about going standalone...
Do not double think go standalone.Originally Posted by packetrace ↑Pimp...I thought you were standalone man its crazy a fic at that boost haha looks like it works pretty great for just a piggyback...
you make me double think about going standalone...
I made a mistake in thinking my AFR was fluctucation. It turns out the were fluctuating because of the missfire. When the missfire occurs the afr went rich because of unburned fuel in the exhaust. I made some progress and its running pretty good after retarding timing a bit farther. Its pulling hard on the highway WOW!!😳 Also Im going to need a new boost guage. Also I seriously need a external wastegate setup. I need to organize a Turbo 5K walk for my car. Gotta raise funds.Originally Posted by scioncrew ↑you got to stabilize you AFR. give it some more fuel make run 11.0-10.5 AFR then work your way back. you should not be misfiring like that if you have the proper fuel deleavery system in you car.
I called Ptunning about the turbo manafold I was looking at, and they said they have none in stock and it would take at least a month to make one. I was a little dissapointed. I am holding off on the order for now and rethinking this.
1 attachment not included in this copy
🎉 good to hear you found the problem
are you standalone ?Originally Posted by Yoda ↑Do not double think go standalone.
ohhhh niceee man!!!Originally Posted by pimp my yaris ↑I made a mistake in thinking my AFR was fluctucation. It turns out the were fluctuating because of the missfire. When the missfire occurs the afr went rich because of unburned fuel in the exhaust. I made some progress and its running pretty good after retarding timing a bit farther. Its pulling hard on the highway WOW!!😳 Also Im going to need a new boost guage. Also I seriously need a external wastegate setup. I need to organize a Turbo 5K walk for my car. Gotta raise funds.
I called Ptunning about the turbo manafold I was looking at, and they said they have none in stock and it would take at least a month to make one. I was a little dissapointed. I am holding off on the order for now and rethinking this.
Nope not yet but once I have the funds most deffOriginally Posted by packetrace ↑are you standalone ?
I looked at the pt mani and just didn't like having my turbo exposed to the open environment. It rains a lot here in Florida. I know Garm has manifolds too did u check with him? What turbo are you runnin now?
Running MAP in the southeast, south, and southwest is much easier with it since its based off of a fuel curve that is programed into the ECU or Piggyback and it does not change. So basically, your fuel map never changes no matter what the air conditions are outside (dense, thin, wet, dry, etc). I don't know enough about MAP setups yet to do much more than sound dangerous, but going off what i have learned so far using your car for a racing application would easily justify going MAP since the car many times isn't a DD for most folks, but in this case it is his DD. He would need a 2 BAR Stainless Steel Sensor Kit which are over 100 bucks and then he would need to modify his piping or even replace a section so it is another investment for sure. IMHO if you are going to make the change and investment to go MAP then you are better off ditching the FIC to go full standalone since you are looking to optimize for higher boost and the FIC just doesn't protect your investment. It seems the FIC is for folks wanting to use low boost which traditionally won't put your engine in much for danger of blowing up compared to medium/high boost. 8-10psi is fun as it is on the roads so I would think that 15-18psi is more giggles for sure when at the wheel so being patient at that point rather than risk further time/money makes more sense. I am not sure what most would consider FI changing from a hobby build to serious is since it is subjective based upon the driver and the vehicle, but to me going over 15psi is getting serious.Originally Posted by Yoda ↑The on-board map sensor is good for ~22psi.
Not sure I understand what this is in reference to. He doesn't need a kit of any kind if he stays below~22psi. The FIC can handle that level just fine.
Right, but you would be crazy to not have the Inlet Temp Sensor along with it. Sure, it has MAP built right in, but that is a static setting. You configure MAP instead of MAF, but MAP has no way to adjust for air density changes, in-climate weather, etc. The only way for the ability to have "on the fly" adjustment is with the Inlet Sensor being place too. Someone would be forever fiddling with the configurations throughout the year in northern states or Canada because of this. How is the FIC going to know inlet density/temps/humidity without an inlet sensor?Originally Posted by Yoda ↑Not sure I understand what this is in reference to. He doesn't need a kit of any kind if he stays below~22psi. The FIC can handle that level just fine.
I know all about the temp difference and if you really have extreme varying weather then sure the sensor is nice to have. But you are implying that some change or investment is needed to use the MAP sensor. I am saying there is no investment needed it comes with the unit. The MAF sensor cant handle the boost that high. Many have tuned up to 20 psi for years with no problem. They have their winter tune and a summer tune. Switch between the two and you are set. Still a standalone unit is much better all round but for what he is using it for, FIC all the way.Originally Posted by fnkngrv ↑Running MAP in the southeast, south, and southwest is much easier with it since its based off of a fuel curve that is programed into the ECU or Piggyback and it does not change. So basically, your fuel map never changes no matter what the air conditions are outside (dense, thin, wet, dry, etc). I don't know enough about MAP setups yet to do much more than sound dangerous, but going off what i have learned so far using your car for a racing application would easily justify going MAP since the car many times isn't a DD for most folks, but in this case it is his DD. He would need a 2 BAR Stainless Steel Sensor Kit which are over 100 bucks and then he would need to modify his piping or even replace a section so it is another investment for sure. IMHO if you are going to make the change and investment to go MAP then you are better off ditching the FIC to go full standalone since you are looking to optimize for higher boost and the FIC just doesn't protect your investment. It seems the FIC is for folks wanting to use low boost which traditionally won't put your engine in much for danger of blowing up compared to medium/high boost. 8-10psi is fun as it is on the roads so I would think that 15-18psi is more giggles for sure when at the wheel so being patient at that point rather than risk further time/money makes more sense. I am not sure what most would consider FI changing from a hobby build to serious is since it is subjective based upon the driver and the vehicle, but to me going over 15psi is getting serious.
Maybe i am misunderstanding something.
Actually it doesn't have to be exposed, I chose to remove the cowl for ventilation. I put it back on in the fall to keep leaves out. On customers builds I leave it on, some trimming needed.Originally Posted by Yoda ↑I looked at the pt mani and just didn't like having my turbo exposed to the open environment. It rains a lot here in Florida. I know Garm has manifolds too did u check with him? What turbo are you runnin now?
Picture not included in this copy
1 attachment not included in this copy
That's awesome to know! Do you get to keep your AC lines and would it fit in the Yaris bay. Really like your mani design.
just awesome!!! what engine management do you normally uses ? piggy back ?
If anyone is interested in the manifold e mail Andrew@ptuning.com
I called about the manifold he said it would take a month to make one. If U had it in stock I would have bought one. You should keep a couple on the shelf. Im still liking it, mabe for spring. Dont want to swap it out in the cold.Originally Posted by Blown_xa ↑If anyone is interested in the manifold e mail Andrew@ptuning.com
I recently had a huge loss in power while tuning at 19 psi of boost. I thought it was a clogged converter or muffler. Possibly a boost leak or BOV not closing. That was all wrong, it turns out I had a mass air flow sensor trouble code. I could not see it because my CEL is on all the time because my 02s sensors are disconnected. I cleared the code and the problem is fixed. Back to full power. I may need to adjust my MAF clamp voltage.
Probably an out of range code and it went to default values.
The ptuning maniold on their website does not look equal lenght ?
I think its about as close as you can get woth the space under the hood. I have seen one other but it required relocating the battery. And was over 2000$. I like the turbo above the valve cover. Looks cool and will make the exhaust much straighter and easier to fabricate.
welll Parmas has build an equal lenght one...he is selling it...i have asked if he wants to sell it alone with down pipe and not with whole piping....
TBR makes one which might be the one your talking about...:)
TBR makes one which might be the one your talking about...:)
The one Parmas had came with the motor from Canada -- he didn't build it, as I recall.
i think is an engine from turbinetech here !
Yes it is :) they want 1000$ for an equal lenght haha
Might pick one from ptuning or try to copy it of parmas dont want to sell his equal lenght alone
Just posting an update. I have sorted my ignition issues by adjusting my timing map. My car has been running very strong at 17psi. Making more power then ever before. I continue to tweek and fiddle with the FIC. Sometimes adjustments work and sometimes they dont. I can say it is getting hard to tune on the street. Sometimes I wish I had a dyno. Trying to find a road to wind out forth gear is a little risky with traffic and the police.
Traction is a real problem. With cold weather their is none until third gear. Even third gear is starting to break loose somtimes. And I have major torque steer. Mabe a limited slip would help.
My light piston slap has not caused any issues with reliability. I just finished a trip to Tennessee with my bike on the trailer behind my car. It is pretty loud when cold but its taking some hard driving.
I want to get a dyno run in the next few months and see what she puts out? I also want to pick up a welder and build a quality exhaust. Also next summer I would like to get a new turbo manafold and slightly larger turbo with a external wastegate.
Traction is a real problem. With cold weather their is none until third gear. Even third gear is starting to break loose somtimes. And I have major torque steer. Mabe a limited slip would help.
My light piston slap has not caused any issues with reliability. I just finished a trip to Tennessee with my bike on the trailer behind my car. It is pretty loud when cold but its taking some hard driving.
I want to get a dyno run in the next few months and see what she puts out? I also want to pick up a welder and build a quality exhaust. Also next summer I would like to get a new turbo manafold and slightly larger turbo with a external wastegate.
^ Way to go!
LSD will help a LOT with your torque steer, I have very little of that on my car. Tires may be helping, I don't know, I run Toyo R888's, very sticky tires.
LSD will help a LOT with your torque steer, I have very little of that on my car. Tires may be helping, I don't know, I run Toyo R888's, very sticky tires.
Glad to hear all is going well for the most part. I am very glad that I went with an external WG...just makes life a lot easier as well as being more reliable in winter conditions. My daughter actually had a friend over from New Brunswick during the Turkey Day weekend and he has a boosted Golf that had an internal WG that experienced the same issue I did with the actuator sleeve arm getting gummed 2 winters ago. He got lucky though because his stuck closed rather than open so no damage, just shitty performance.
I think you got that backwards, if stuck closed it would build up to much boost stuck open it would not build any boost.Originally Posted by fnkngrv ↑Glad to hear all is going well for the most part. I am very glad that I went with an external WG...just makes life a lot easier as well as being more reliable in winter conditions. My daughter actually had a friend over from New Brunswick during the Turkey Day weekend and he has a boosted Golf that had an internal WG that experienced the same issue I did with the actuator sleeve arm getting gummed 2 winters ago. He got lucky though because his stuck closed rather than open so no damage, just shitty performance.
^ Correct.
as long as your piston skirts are not broken off, and you have good sealing rings the slap will always go away once the engine warms up and the pistons expand to fit the cylinders. I would suggest some way of warming up the engine before driving to prevent possible damage to the cylinder walls and pistons.
BUT, I am glad to hear(well read) that the set up is doing good and is feeling strong, and i look forward to reading your dyno results. keep up the fun/good work.
BUT, I am glad to hear(well read) that the set up is doing good and is feeling strong, and i look forward to reading your dyno results. keep up the fun/good work.
I would suggest some way of warming up the engine before driving to prevent possible damage to the cylinder walls and pistons.LOL, like sitting in the car and starting it? 😆
that is what i do, wait until the O2 sensor is warmed up enough to start working (130 degrees Fahrenheit) then easy down the road a few miles, wait at a light, easy down the road toward the interstate, get on the interstate, and by then i'm about 175 ish, so i can give it some gas to merge onto the interstate. and laugh as i hear the loud roar as my exhaust goes through the Megan Racing header, and out the DC Sports Muffler. oh the sound of a little 1.5L sounding like a much bigger car. just kind of make me smile, now if only I had a turbo as well.
Well for a long time now I have been trying to tune my FIC for 20psi. I have never been able to get it quite right. Because of the difference in fueling from the factory computer at say 60% throttle opening at 10 psi compared to 100% throttle opening at 10psi. If tuning for 100% throttle you will be very lean at 60% throttle. If tuning for 60% you will be pig rich at 100%. I have tried to find a happy balance but its just not possible. I have turned the boost down to the 12-13psi range. This is a little bit more managable. To get the full potential of this built motor it will need a stand alone. Its just more then I want to spend at the moment.
Just curious how does the boomslang hook up to the AEM EMS and the factory computer at the same time. I now the power steering still needs to hooked to the factory computer. Also can I still use my A/C. Anyone know?
Just curious how does the boomslang hook up to the AEM EMS and the factory computer at the same time. I now the power steering still needs to hooked to the factory computer. Also can I still use my A/C. Anyone know?
Oh man, you must be itching to get a standalone knowing you have a built motor you can barely make use of 🙁
I can't speak for how the boomslang would work in that regard. I can't imagine they'd completely disregard usage of the stock ECU because you would be losing a huge amount of functionality.
This may not be the best example because the wiring is custom but - in my tC, both the Motec ecu and stock ecu are used. The Motec really only takes control over what's necessary to manage the engine. It also has configurable inputs for a huge slew of things. I'd imagine any decent standalone would have the same.
As for A/C - I believe the way I have it handled is you flip a switch (NOT the oem one), the Motec sees this as an "a/c request" then powers a relay which is connected directly to the a/c clutch. The stock ecu is completely bypassed.
I can't speak for how the boomslang would work in that regard. I can't imagine they'd completely disregard usage of the stock ECU because you would be losing a huge amount of functionality.
This may not be the best example because the wiring is custom but - in my tC, both the Motec ecu and stock ecu are used. The Motec really only takes control over what's necessary to manage the engine. It also has configurable inputs for a huge slew of things. I'd imagine any decent standalone would have the same.
As for A/C - I believe the way I have it handled is you flip a switch (NOT the oem one), the Motec sees this as an "a/c request" then powers a relay which is connected directly to the a/c clutch. The stock ecu is completely bypassed.
Oh yeah.... haha 🍻Originally Posted by kou ↑I think you got that backwards, if stuck closed it would build up to much boost stuck open it would not build any boost.
Originally Posted by pimp my yaris ↑Just curious how does the boomslang hook up to the AEM EMS and the factory computer at the same time. I now the power steering still needs to hooked to the factory computer. Also can I still use my A/C. Anyone know?
I am wondering this as well. I REALLY want to stay away from AEM again, but may end up having to go that route. I know there are plenty of folks that swear by them, but I have had too many issues to not be leery with their products. So I would like to know whether or not I would still be able to use my Bslang or if I will have to pick up a new harness also. 😕