pimp my yarisOriginal postchicago · Jul 7, 2010#1I want to build a costom turbo setup using mostly E-bay parts. I am thinking t25/28 turbo. I have found exhaust manafold/turbo, intercooler and piping,oil and water lines if needed. Also a air intake and filter to mount the mass air sensor. I am sure I will need to buy at least 1 more intercooler piping kit and a blow off valve. And I found a downpipe witch will need to be costomized from a nissan silvia. Or I will need a complete costom downpipe.
My questions are what piggy back system should I use to control injector pulse? Will I need bigger injectors right away? I am only looking for 150-170whp. Also should oil source for turbo be tapped from oil pressure sensor or do I need to buy adapter to tap near the filter? I am also sure a new clutch will be in my future shortly after install. I am thinking center force dual friction.
Also can I tune a piggy back system with a lap top and a wide band o2s or do you need some specialized training to complete this. I am a ase master tech for about 12 years, but I have never done tuning. Its just so dame expensive around Chicago. Very few places to go.🤷
5 attachments not included in this copy
Replies 609
pimp my yarisThread starterchicago · Jul 7, 2010#2Also 1 more question. Has anyone used this turbo manafold set up? I want to know if it interfers with A/C lines? I want to retain my A/C.
cali yarisCanoga Park, CA · Jul 7, 2010#3I think you'll need a tuner, but maybe not. Piggybacks are problematic with the Yaris, but at least one member has an AEM FIC working properly. I personally don't mind doing some street tuning, but I insist on at least one dyno session to get it just right and make sure it's a reliable and thorough tune.
Corolla injectors will serve you for this project. What is the internal gate set for in psi?
T25 is a nice small turbo for us, nimble and quick to spool.
What brands are the parts? Especially the turbo, it's the heart of your system. How is the customer service if a part fails?
My turbo mani is $249 shipped.
PETERPOOPOahu · Jul 7, 2010#4My tune with the greddy emanage ultimate is still doing ok.
pimp my yarisThread starterchicago · Jul 7, 2010#5Internal wastegate for the turbo in the picture is set to 7psi. No word on the brand of turbo. compressor housing is .80AR, turbine side is .86AR. Cast iron manafold also includes 35/38mm wastegate flange for external wastegate. I,m sure costomer service is shitty. Its a non ball bearing turbo. But 450$ shipped for manafold, turbo, oil line and gaskets sounds cheap even if the turbo is not top quality. I figure if it blows I would upgrade to a better ball bearing turbo later.
cali yarisCanoga Park, CA · Jul 7, 2010#6if it blows you may be upgrading more than the turbo - but it's your risk to take. As long as it's not your daily driver, go for it.
If you're getting a turbo with an internal gate, why would you get a manifold with a wastegate flange?
and "compressor housing is .80AR, turbine side is .86AR" is way too large. You'll have so much lag with that. For comparison, the Garrett GT2554R is .64 turbine side.
pimp my yarisThread starterchicago · Jul 7, 2010#7Has anyone tuned using the Apexi Afc-neo? Just curious how it worked out. It looks like a bargain price. Claims to alter mass air flow sensor readings to change injector pulse width.
pimp my yarisThread starterchicago · Jul 7, 2010#8Also have you guys retarded timing when in the boost. If so how much ie: 1degree/1pd boost. I am asking because the Apexi AFC-neo I mentioned previously has no provision for adjusting timing. Could be very important. Detonation bad
cali yarisCanoga Park, CA · Jul 8, 2010#9A little timing is taken out in my tune, not a whole lot.
You didn't attend to any of the comments/questions in post 6.
pimp my yarisThread starterchicago · Jul 8, 2010#10Cali yaris I saw the turbo manafold your selling. Looks like very good quality. I see it mounts the turbo under the manafold. While this Ebay set up mounts turbo above the manafold. I think your setup may be better for clearance with the A/C lines. Have you had any feedback about that manafold, any clearance problems? I looked into that turbo you mentioned, but for right know thats a little out of my price range. It was selling for 900-1000$
cali yarisCanoga Park, CA · Jul 8, 2010#11I only have my own feedback about the manifold. I'm throwing 24 psi at it and getting nice power. No cracks or issues of any kind. Fitment is great, no clearance issues with any other systems.
how about this one:
If you're getting a turbo with an internal gate, why would you get a manifold with a wastegate flange?
pimp my yarisThread starterchicago · Jul 8, 2010#12The E-bay ad mentioned a wastegate flange. But none can be seen in either picture of the manafold. Anyway I dont like mounting the turbo above the manafold next to the cyl. head. I think it will cause clearance problems with a/c lines and will be to hot and close to ECM. I think I will be purchasing your manafold sometime this month. You sold me. Funds are limited. I will be starting with manafold and turbo then I can start planing routing for intercooler pipes. Gotta get that mental picture and piece it together you know!
pimp my yarisThread starterchicago · Jul 8, 2010#13To bad you are not selling a downpipe for a t25 mounted on your manafold. That would be sweet
pimp my yarisThread starterchicago · Jul 8, 2010#14I forgot to ask. What turbo is this manafold your selling designed to fit? Cali
pimp my yarisThread starterchicago · Jul 8, 2010#15Just doing some more turbo comparisions. Found T3 w/internal wastegate and v/band exit. .5" a/r compressor and .63" a/r turbine. Possibly the smaller size could be more yaris friendly. V/band exit could make downpipe easier to fabricate.
SabretoothSt Cloud FL · Jul 8, 2010#16T3 will be a bit too large, t25 will be fine and will allow you plenty of breathing room between actual turbo output and its maximum output.
Garms manifold should be for a t25 turbo, if I am wrong he will chime in to do so.
ParmasML · Jul 8, 2010#17We all know that good quality and efficient parts are expensive but if you decide to go for the cheap parts (like that turbo) you will absolutely scrap what you bought and eventually going for the expensive ones.
I don't know about that intake filter but I am about sure you will have to make it custom. *Remember that now the intake is the turbo and not the throttle body!
A T25 0.64 turbine is the best turbo you can get for balanced power/torque and spooling time. Keep in mind that there are turbos that feature watercooling which is a plus but not a must.
RE: Oil turbo feed, you have two choices :
1. Tap the block
2. Install a sandwich adapter
Mine is tapped at the front and rear probably similar to Garm setup but that is your choice.
Don't buy intercooler piping unless the turbo setup (turbo+ Ex manifold + intercooler) is of the same manufacturer. If you go with Garm's manifold you need custom piping to match turbo.
Clutch is an option upgrade but that depends how much you love your throttle pedal. If so clutchmasters are the most recommended brand.
RE: Piggy back, choose carefully and buy only proven ones unless you don't want to waste cash trying indefinetely to tune it right.
cali yarisCanoga Park, CA · Jul 8, 2010#18^ good points -- Parmas has been working on his built set up for a while now, and he's learned so much along the way.
my mani has a T25 flange.
pimp my yarisThread starterchicago · Jul 9, 2010#19Thanks for the advise guys. I will post more as it moves along.
pimp my yarisThread starterchicago · Jul 10, 2010#20OK yesterday I ordered Garms Turbo manafold off Micro Image and also a GT25 turbo from E-bay. I will see how it mounts up then I will start planing costom intercooler piping and downpipe routing. Also will need to measure for oil feed and return line. And what I will need to tap pan for retun line. Any sugestions for return line tap would be helpful.🤷
Turbo specs. I think this turbo should spool quickly and be good for low boost application
TURBO SPEC:
gt25 internal wastegate turbo charger
Intake :2.5 inch
Outlet: 2 inch
Compressor trim: .42 ar
Compressor Wheel diameter: 60.05 /42.12
Turbine wheel diameter : 46.46 /53.20
Exhaust trim: .49ar
Turbine flange type: t25 flange
Downpipe flange type : 5 bolt type (will not fit sr20 down pipe bolt pattern)
Cooling type: oil and water cool
Actuator : set at 8psi
Horsepower rating: 250-300hp+
(wet float bearing)
1 YEAR WARRANTY IF INSTALLED BY PROFESSIONAL MECHANIC ( ASE CERTIFIED)
Turbo was $239.99 shipped to my door
4 attachments not included in this copy
cali yarisCanoga Park, CA · Jul 10, 2010#21You're on the right track! 👏
I think I would have gone 6 psi but this is a great experiment, and finally someone is ACTUALLY DOING IT. 🙇
Mani went out promptly yesterday.
Our oil "pan" is really just a cover. We tapped the front of the block above that for my return line.
ParmasML · Jul 10, 2010#22Is the engine 1.5L or 1.3L? Just to confirm as it was never mentioned here
I think the actuator set to 8psi is not good for stock internals. Make sure you buy a boost controller and set it to the most minimum levels... you don't want your turbo to boost a spike while you rev it to 6Krpm on first gear and end up on 10 or even 12psi boost. At that level of boost (10-12psi) I am confident your internals won't hold long so make sure you install a controller.
Also since you are installing additional oil lines make sure you install an oil pressure (or also oil temprature) to monitor your oil status. Before you drive happy and confident you need to check especially oil pressure during idle gradually till 5Krpm on neutral. If all is fine you can burn some tires after a good tune!
An Air to Fuel Ratio (AFR) is an option to check how your mixture is doing off and on boost. This gauge can prevent you before you destroy your engine especially if you run lean on-boost
Cheers and Good luck
PETERPOOPOahu · Jul 10, 2010#23 Originally Posted by
cali yaris ↑ finally someone is ACTUALLY DOING IT. 🙇
I was just going to say, "Wow this guy sure moves fast." The only guy to ask the same ol` turbo questions, but then actually DOES IT! lol. Way to go bro! 👍
cali yarisCanoga Park, CA · Jul 10, 2010#241. definitely a couple of gauges will be needed.
2. strongly recommend an extra O2 bung in your downpipe. you'll be glad it's there someday, and it's a pain to take out and add later.
3. re: parmas comment -- you can't have less than the spring pressure, so if the spring is 8psi, that's the minimum you can run. A boost controller is a great idea to prevent the spikes/surges he is warning about.
ParmasML · Jul 10, 2010#25 Originally Posted by
cali yaris ↑ 3. re: parmas comment -- you can't have less than the spring pressure, so if the spring is 8psi, that's the minimum you can run. A boost controller is a great idea to prevent the spikes/surges he is warning about.
Normally a boost controller control boost levels and spring pressure. If we consider the AEM TRU boost it has a boost level percentage setting of 10% as minimum and a spring pressure setting of 1 minimum.
This is an example.... On my setup (in which the actuator is set to 9psi) the AEM needs to be set to boost level of 10% and spring pressure setting of 5 to get good response. Since I had mixture problems I decided to use stock plugs and I needed to have the engine running at the lowest boost possible. So I adjusted the spring pressure to 1 and boost became laggy and it need much more revs to produce that 9psi and I worked fine liked that since I was only hitting 4psi during street driving.
cali yarisCanoga Park, CA · Jul 10, 2010#26 Normally a boost controller control boost levels and spring pressure.
No, it cannot control spring pressure. A spring has a fixed resistance. The boost controller keeps the wastegate closed at or above the spring pressure, and the spring is what allows it to open. So the spring pressure is the minimum boost.
I'll just leave it with my disagreement on this point, the thread is for the OP's turbo build.
scioncrewHB · Jul 10, 2010#27Link to a thread or page that is not in the archive1 attachment not included in this copy
pimp my yarisThread starterchicago · Jul 10, 2010#28I have to agree with you, boost controller can not override spring pressure in actuator as it is sealed and completely mechanical. I think it is a little to much boost to start with. I think I will rig up I spring to work against the actuator to help it open sooner until I can get it to a local tuner. I know it may sound ghetto, but its better then the cost of a new motor. At least until its properly tuned. But I still have a lot of work to do. And right now Im out of flow until my next pay day. Also its a 1.5L motor. I do want to install a wide band o2s and air/fuel ratio guage and boost guage on inside window pillar. I think I will take many pictures and post as this rolls along.
pimp my yarisThread starterchicago · Jul 10, 2010#29Thanks for that scioncrew. I was not aware of that adjuster.
pimp my yarisThread starterchicago · Jul 10, 2010#30Does anyone run stock injectors with boost? I didnt think the blitz supercharger came with injectors. I heard you should not excede 80% duty cycle with any injector while tuning or it becomes unreliable and may fail.
cali yarisCanoga Park, CA · Jul 10, 2010#31the blitz s/c does not come with injectors. If you want to experiment, try to tune with stock, then move up if they can't handle it. Or move up and know you've got enough to start with.
cali yarisCanoga Park, CA · Jul 10, 2010#32 I think I will take many pictures and post as this rolls along.
You better! If you don't, it didn't happen. 😁
Focus_Sh1ftNew Jersey · Jul 10, 2010#33 Originally Posted by
pimp my yaris ↑ OK yesterday I ordered a GT25 turbo from E-bay.
Is this one of those from the sr20det setup? I was eyeing this up after having it pointed out... Just been wondering on its quality.
Originally Posted by
pimp my yaris ↑ Does anyone run stock injectors with boost? I didnt think the blitz supercharger came with injectors. I heard you should not excede 80% duty cycle with any injector while tuning or it becomes unreliable and may fail.
Check out cdydjded's profile. He has an A/F graph of stock injectors and 1ZZ injectors.
Also, not to threadjack, but since it was touched on here... Garm, I'm wondering if you could possibly post a picture of your oil tap location. I've been wondering how you pulled this off for awhile lol.
cali yarisCanoga Park, CA · Jul 11, 2010#34sure thing, next time i'm near the car, which is Monday
pimp my yarisThread starterchicago · Jul 11, 2010#35The turbo on the sr20det is usually a gt25g. Its larger, has a a/r 80 compressor. Nice pic and info on wikipedia. The last turbo ride I had was a Suby wrx. It put down 300 on a axel dyno. My local tuner must have done 100 runs into the night. Their neighbors were sure pissed off. They have since changed locations. I ran a
larger tubo and injectors. No piggy back, they reflashed the stock ECU and also turned off my cel. due to missing cat. converter. He also included a
second low boost map that could be turned on using the defroster switch. Nice if U let someone barrow your car. Its nice when the aftermarket loves your car.
cali yarisCanoga Park, CA · Jul 11, 2010#36100 pulls, ouch.
Focus_Sh1ftNew Jersey · Jul 11, 2010#37 Originally Posted by
cali yaris ↑ sure thing, next time i'm near the car, which is Monday
As a token of my appreciation, I believe it's time for me to order that Eurolight kit I've been eyeing up. 👍
cali yarisCanoga Park, CA · Jul 11, 2010#38haha, and so you did. Now I HAVE to take that picture 🙂
pimp my yarisThread starterchicago · Jul 12, 2010#39Hey Garm this manafold from Turbo-kits.com looks a lot like yours. Do you guys use same supplier? I need that downpipe from their kit. Looks like it would work good with my setup.
3 attachments not included in this copy
pimp my yarisThread starterchicago · Jul 12, 2010#40looks like his mani has a EGT bung
cali yarisCanoga Park, CA · Jul 12, 2010#41different supplier, their manifold is fine. That downpipe did NOT fit my car, however (it was modeled on an xB). I also had a perfectly horrible customer experience with them trying to get the parts I did order (took four months to get something that was supposedly "in stock").
scioncrewHB · Jul 12, 2010#42didn't fit the XB either! I had to modify mine to fit 👎 i quess that what i get for being lazzy and not make it my self.
pimp my yarisThread starterchicago · Jul 12, 2010#43Wow that service blows. Are U going to sell the downpipe U had fabricated or is it a one shot piece?
pimp my yarisThread starterchicago · Jul 17, 2010#44Got my Turbo and manafold yesterday. Wed, I will mount up and check for clearance and measure for oil lines. Also I talked to a local tuner and he sugested Emanage ultimate piggy back. Also found a place that will fabricate a costome plug and play harness for the emanage ultimate, but its 500$. If anyone is intrested its called Boomslang Fabrication. It was recomended by the tech guy at Greddy.🤤
4 attachments not included in this copy
scioncrewHB · Jul 18, 2010#45looking good! good luck man
scioncrewHB · Jul 18, 2010#46 Originally Posted by
pimp my yaris ↑ Wow that service blows. Are U going to sell the downpipe U had fabricated or is it a one shot piece?
love to help but i have an XB. i need a car to do it.
cali yarisCanoga Park, CA · Jul 18, 2010#47No one knows if the boomslang is compatible with the USDM ECU. It seems like it should be, but we won't know until someone tries it (hint hint)
Bluevitz-rsOshawa, Ontario, Canada · Jul 18, 2010#48 Originally Posted by
cali yaris ↑ ... the boomslang ...
😕
cali yarisCanoga Park, CA · Jul 18, 2010#49Boomslang (company name) makes a plug 'n play wiring harness for the AEM FIC and the Yaris.
Nexus1155Dorchester · Jul 18, 2010#50Change the setup you have for the wastegate and boost pickup lines to a MBC setup, this way it will boost to the psi you want and you will get no wastegate issues.
Also, thats a chinese turbo, prime the crap out of it with the fuel fuse removed so it will deliver oil to it before you start up the car. I have them on my car and just started it up this week.