Replies continued
pimp my yarisThread starterchicago · Sep 23, 2010#201The last two pictures show how many wires were actually used for my car, [those were under hood] and how many were not used [hanging under dash].
Its not because I'm lazy. This thing was designed to work with any car. Their is wiring for hall effect sensors and magnetic sensors. Only the mag. were used. Their is also several options like a rpm activated programable switch. And the ability the use and manipulate the factory O2 sensor. I am using a wideband.
3 attachments not included in this copy
Focus_Sh1ftNew Jersey · Sep 23, 2010#202👍
Funny, because I'm waiting for my wideband but had my FIC right from the get-go.
I should be able to begin tuning next week so we gotta help each other out. 🙂
How exactly are you planning on going about this? Clamp MAF, remap, watch STFT, then adjust fuel maps?
sleey0PA · Sep 23, 2010#203Wait, so how many wires total for our cars?
I am still debating whether or not to pony up the $499 boomslang wants for a pre-wired FIC harness.
You know what would be FRIGGIN sweet? A little guide on which wire goes where. IF you don't mind, of course:D
Nexus1155Dorchester · Sep 23, 2010#204Yeah I would like someone to make a nice little excel wiring chart that would be neat-o. But if you are going to get an FIC and the Boomslang and drop around $850 on it and probably more on getting it tuned, you might as well try the DEZOD setup for a little bit more and have an easier time tuning it yourself with more capability?
Focus_Sh1ftNew Jersey · Sep 23, 2010#205 Originally Posted by
Nexus1155 ↑ Yeah I would like someone to make a nice little excel wiring chart that would be neat-o. But if you are going to get an FIC and the Boomslang and drop around $850 on it and probably more on getting it tuned, you might as well try the DEZOD setup for a little bit more and have an easier time tuning it yourself with more capability?
Bingo. This thing isn't hard to wire up at all.
Originally Posted by
sleey0 ↑ Wait, so how many wires total for our cars?
I am still debating whether or not to pony up the $499 boomslang wants for a pre-wired FIC harness.
You know what would be FRIGGIN sweet? A little guide on which wire goes where. IF you don't mind, of course:D
I have a guide for this, I just haven't posted it up yet. Also need to wire up my cam and crank wires still.
EDIT: Here's a quick excerpt of wiring:
FIC Power (IGN PWR) - A21-1 or A21-2
FIC Gnd (PWR GND) (SIG GND)- C20-104
Injector 1 (INJ 1 IN/OUT)- C20-108
Injector 2 (INJ 2 IN/OUT) - C20-107
Injector 3 (INJ 3 IN/OUT)- C20-106
Injector 4 (INJ 4 IN/OUT)- C20-105
MAF (MAF IN +/OUT +)- C20-118
TPS (TPS+)– C20-115
Cam+ (CAM1 MAGI+/MAGO+) - C20-99
Cam- (CAM2 MAGI-/MAGO-)- C20-121
Crank+ (CRK MAGI+/MAGO+)- C20-122
Crank- (CRK MAGI-/MAGO-)- C20-121
ECM pinout:
http://www.powerenterpriseusa.net/pr...risControl.pdf Then, of course, some wires are tap while others are intercept. The guide I wrote AND the FIC manual details how they should be attached. It's cake tbh. No reason to spend $500 unless you're deathly scared of doing wiring, at which point I wonder how you have the balls to install a supercharger but not make a couple splices.😛
sleey0PA · Sep 23, 2010#206Depends.
The boomslang will be last resort. If someone does make a nice cheat sheet I will gladly wire it or have a buddy do it, if possible.
If not, I might just say f-it and get the slang. They do sell an extender harness for $399. This might make more sense so I can save my cars wiring from cutting and also I can wire the fic into it in the comfort of my living room and recliner:D
Besides, dezod wants $2k for it and that I don't have. Not sure I want a stand-alone anyway.
sleey0PA · Sep 23, 2010#207 Originally Posted by
Focus_Sh1ft ↑ Bingo. This thing isn't hard to wire up at all.
I have a guide for this, I just haven't posted it up yet. Also need to wire up my cam and crank wires still.
Not hard for you. lol
Without some clear cut pin-outs of which wires I need from the ECU it might be a little difficult for me😳
EDIT: Ahh. I see you have a guide on the way. THANK YOU SOOOOO MUCH!!!!!
Nexus1155Dorchester · Sep 23, 2010#208eeeeek 2k i thought it was around $1200 ill have to recheck that thread
sleey0PA · Sep 23, 2010#209I am sure he said $2k. maybe you are right.
He was going to cut a deal with someone here to test it out so he can get some more customers, but that was an exception.
Regardless, I think that would be overkill for me. As long as focus put up that guide I will be fine:D
pimp my yarisThread starterchicago · Sep 23, 2010#210 Originally Posted by
Focus_Sh1ft ↑ Bingo. This thing isn't hard to wire up at all.
I have a guide for this, I just haven't posted it up yet. Also need to wire up my cam and crank wires still.
EDIT: Here's a quick excerpt of wiring:
FIC Power (IGN PWR) - A21-1 or A21-2
FIC Gnd (PWR GND) (SIG GND)- C20-104
Injector 1 (INJ 1 IN/OUT)- C20-108
Injector 2 (INJ 2 IN/OUT) - C20-107
Injector 3 (INJ 3 IN/OUT)- C20-106
Injector 4 (INJ 4 IN/OUT)- C20-105
MAF (MAF IN +/OUT +)- C20-118
TPS (TPS+)– C20-115
Cam+ (CAM1 MAGI+/MAGO+) - C20-99
Cam- (CAM2 MAGI-/MAGO-)- C20-121
Crank+ (CRK MAGI+/MAGO+)- C20-122
Crank- (CRK MAGI-/MAGO-)- C20-121
ECM pinout:
http://www.powerenterpriseusa.net/pr...risControl.pdf Then, of course, some wires are tap while others are intercept. The guide I wrote AND the FIC manual details how they should be attached. It's cake tbh. No reason to spend $500 unless you're deathly scared of doing wiring, at which point I wonder how you have the balls to install a supercharger but not make a couple splices.😛
With these pics. Its about all U need for a install guide😁
2 attachments not included in this copy
sleey0PA · Sep 23, 2010#211You guys ROCK!
Thanks!
sleey0PA · Sep 23, 2010#212 Originally Posted by
Focus_Sh1ft ↑ Bingo. This thing isn't hard to wire up at all.
I have a guide for this, I just haven't posted it up yet. Also need to wire up my cam and crank wires still.
EDIT: Here's a quick excerpt of wiring:
FIC Power (IGN PWR) - A21-1 or A21-2
FIC Gnd (PWR GND) (SIG GND)- C20-104
Injector 1 (INJ 1 IN/OUT)- C20-108
Injector 2 (INJ 2 IN/OUT) - C20-107
Injector 3 (INJ 3 IN/OUT)- C20-106
Injector 4 (INJ 4 IN/OUT)- C20-105
MAF (MAF IN +/OUT +)- C20-118
TPS (TPS+)– C20-115
Cam+ (CAM1 MAGI+/MAGO+) - C20-99
Cam- (CAM2 MAGI-/MAGO-)- C20-121
Crank+ (CRK MAGI+/MAGO+)- C20-122
Crank- (CRK MAGI-/MAGO-)- C20-121
ECM pinout:
http://www.powerenterpriseusa.net/pr...risControl.pdf Then, of course, some wires are tap while others are intercept. The guide I wrote AND the FIC manual details how they should be attached. It's cake tbh. No reason to spend $500 unless you're deathly scared of doing wiring, at which point I wonder how you have the balls to install a supercharger but not make a couple splices.😛
Start a new thread to be stickied with the full guide, whenever you post it.
THANKS!🤘
Oh, and I guess it is time for you to get tuned and see what that little supercharger can do! HA!
pimp my yarisThread starterchicago · Sep 23, 2010#213500$ for that boomslang harness is crazy unless your going to remove your turbo. And beleve me, once that turbo is on your only going to want more boost. Just ask Garm! I installed the wiring shown above in about 4-5 hours with a soldering iron solder and shrink wrap. I would have been a lot shorter if I had the info above. I spent most of the time checking sensor wiring diagrams in the toyota service manual. And then rechecking. And then sometimes even checking a third time cause I was drinking LOL 😁
sleey0PA · Sep 24, 2010#214Hahaha. I think I'll leave the drinks when I do mine. Quik connects, FTW!
Too funny....
Yeah, $500 is a lot. But you just plug it in and your done in, what, 30 seconds? AND your OEM wiring isn't cut so if you want to put it back to stock to sell it or something it makes life way easier.
It is rape for $500 but what are ya gonna do when there are no other options for a jumper harness?
Looking at it now I will wire it myself. I thought there would be more wires looking at that FIC harness. There are like 100 wires hanging off that thing!
EDIT: Can someone confirm that the Vitz RS e-manage harness is exact to our cars? I can get one of those for like $200 and just wire in the FIC!:D
Focus_Sh1ftNew Jersey · Sep 24, 2010#215 Originally Posted by
pimp my yaris ↑ 500$ for that boomslang harness is crazy unless your going to remove your turbo. And beleve me, once that turbo is on your only going to want more boost. Just ask Garm! I installed the wiring shown above in about 4-5 hours with a soldering iron solder and shrink wrap. I would have been a lot shorter if I had the info above. I spent most of the time checking sensor wiring diagrams in the toyota service manual. And then rechecking. And then sometimes even checking a third time cause I was drinking LOL 😁
Holy... Don't tell me you wired up the FIC without using that nice and neat ECM pinout hosted on Power Enterprise's site?
Oh and also, I assume you used those wires I listed for the cam and crank? I need to wire mine in still, but I'm guessing that's the correct wire combo.
sleey0PA · Sep 24, 2010#216Yeah, make sure those cam and crank pins are correct.
Wouldnt' want someone to wire it up and it be wrong. lol
pimp my yarisThread starterchicago · Sep 24, 2010#217 Originally Posted by
Focus_Sh1ft ↑ Holy... Don't tell me you wired up the FIC without using that nice and neat ECM pinout hosted on Power Enterprise's site?
Oh and also, I assume you used those wires I listed for the cam and crank? I need to wire mine in still, but I'm guessing that's the correct wire combo.
I used the toyota service manual witch took a little longer. I had to find the wiring diagram for each sensor and figure out witch wire is the sensor output. But in the end I have it wired the same as U. And yes my cam and crank are wired the same as in your little chart. I havent hooked up the fic yet, I will do it later today. I did hook up the jumper bypass connector and started my car with no check engine light. So I think I done good🤷
cali yarisCanoga Park, CA · Sep 24, 2010#218I would sure like to see someone try the Boomslang at some point. Just to know the wiring is correct with it.
So fun to watch your builds come up, guys!
pimp my yarisThread starterchicago · Sep 24, 2010#219I set up a base map today. As it turned out it was very rich. About 10/1. Then I did some minor adjustments and I got my air/fuel ratio in the 11.5/12.7 range. I will still do some more adjustments. I am surprised at how well the stock injectors are doing at 7psi. This thing was very intimidating at first, but after playing around with it I think I'm getting the hang of it. I may have to clamp the mass air in the future as I can feel the transition from closed to open loop fueling.
Focus_Sh1ftNew Jersey · Sep 24, 2010#220 Originally Posted by
pimp my yaris ↑ I set up a base map today. As it turned out it was very rich. About 10/1. Then I did some minor adjustments and I got my air/fuel ratio in the 11.5/12.7 range. I will still do some more adjustments. I am surprised at how well the stock injectors are doing at 7psi. This thing was very intimidating at first, but after playing around with it I think I'm getting the hang of it. I may have to clamp the mass air in the future as I can feel the transition from closed to open loop fueling.
So how exactly did you do it? Give me ALL the details 😁
pimp my yarisThread starterchicago · Sep 25, 2010#221 Originally Posted by
Focus_Sh1ft ↑ So how exactly did you do it? Give me ALL the details 😁
To be honest, it would be a lot of typing. I think my fingers would cramp. If You would like PM me your phone # and I can walk U through it using my puter at the same time. Its not as bad as U think. Let me know when is best time to call as well.
pimp my yarisThread starterchicago · Sep 25, 2010#222Question for the boosted?????? What spark plugs should I be runing with boost? A NGK number would be helpful.
Bluevitz-rsOshawa, Ontario, Canada · Sep 25, 2010#223 Originally Posted by
pimp my yaris ↑ Question for the boosted?????? What spark plugs should I be runing with boost? A NGK number would be helpful.
That depends on what you plugs look like, but generally one heat range colder.
Here's NKG's
website. The 5 is your heat range, so you need a 6 for one step colder.
sleey0PA · Sep 25, 2010#224Most here run heat 7.
I bough ik22's for my buil which are 22 (heat range 7)
Focus_Sh1ftNew Jersey · Sep 25, 2010#225What's wrong with stock plugs?
sleey0PA · Sep 25, 2010#226 Originally Posted by
Focus_Sh1ft ↑ What's wrong with stock plugs?
Well, when you are boosted you need colder plugs so that there will be less chance of detonation if my reading is right.
Most here run the NGK BRK7EIX which is heat range 7. Stock is 5, IIRC. So two steps colder.
I got the denso's becasue they are supposed to be a little better quality and at Amazon they were the same price as the NGK's.
Be advised that Denso has there own heat range system, so IK22 - heat range 22 which = heat range 7.
Denso makes TRD plugs to there specs based off the IK22 so that is why I went with the IK22's. HEck they might be the same as the $50
per plug TRD's. lol
Focus_Sh1ftNew Jersey · Sep 25, 2010#227Eh, I've yet to have any detonation issues running at a 14.7 AFR, so that should be even less of a problem after some tuning. Maybe I'll buy some for fun anyways 🤷
Btw, I like this I scratch your back you scratch my back thing we have going on lol.
cali yarisCanoga Park, CA · Sep 25, 2010#228 I've yet to have any detonation issues running at a 14.7 AFR
You won't be, and better not be, at 14.7 under boost.
sleey0PA · Sep 25, 2010#229Yeah, bro. Two heads are ALWAYS better than one.
If you aren't having any issues than no worries. Do u run 93 octane?
My build target power is going to be 175-180 safely on stock internals.
I was thinking that a boost controller should keep me tame most of the time and the days I need to vent I will dial it up.
I think a lot of ppl underestimate the 1NZ motor.
We shall see!!!!
I found a tuner/performance shop in Buffalo called Swerve motorsports and apprantly there is a guy who works there with a Yaris.
He was thinking of going Blitz sc so we are gonna talk on Monday. I haven't ruled out a turbo and in fact I am leaning that way more and more.
My plans are shaping up well and I cant wait to feel that first bit of euphoria when my install is done, turn the key, and go for my very first boosted drive (well, in my OWN car at least).
You, sir, are a good guy focus.
If theres anything I can help you with u let me know! Jersey isn't that far at all:D
pimp my yarisThread starterchicago · Sep 27, 2010#230Well I found out today my stock injectors maxed out at 8psi at about 5K rpm. At 5K my wideband started going lean. So now its time for injectors.
This thing is really hauling ass now. I am always playing with the FIC trying to get the best tune. First few days I had a bad hesitation when the FIC started adding fuel. I finally got that worked out today.
fnkngrvIn The Hotbox · Sep 27, 2010#231^ awesome
sleey0PA · Sep 27, 2010#232 Originally Posted by
pimp my yaris ↑ Well I found out today my stock injectors maxed out at 8psi at about 5K rpm. At 5K my wideband started going lean. So now its time for injectors.
This thing is really hauling ass now. I am always playing with the FIC trying to get the best tune. First few days I had a bad hesitation when the FIC started adding fuel. I finally got that worked out today.
IS this tuned with the AEM?
Guess it's time to find 1ZZ injectors🤘
pimp my yarisThread starterchicago · Sep 27, 2010#233 Originally Posted by
sleey0 ↑ IS this tuned with the AEM?
Guess it's time to find 1ZZ injectors🤘
Yes AEM FIC!
YodaFL · Sep 27, 2010#234Good job. Get it dynoed
sleey0PA · Sep 27, 2010#235 Originally Posted by
pimp my yaris ↑ Well I just picked up some used 1ZZ injectors that were for sale on E-bay. If anyone was thinking about picking them up, TO LATE I got um! New total 939.49
So you maxxed the 1zz injectors?
I thought u said u had stock ones maxxed?🤷
sleey0PA · Sep 27, 2010#236Oh and what kind of whp does your butt dyno tell you are running?
lol
Focus_Sh1ftNew Jersey · Sep 27, 2010#237Glad that studder is worked out. How's the MAF clamping coming along?
Also, where's that map we talked about? 😛
Originally Posted by
sleey0 ↑ Oh and what kind of whp does your butt dyno tell you are running?
Call me crazy, but the pull feels very samiliar to my Dad's G35 👍
pimp my yarisThread starterchicago · Sep 27, 2010#238 Originally Posted by
sleey0 ↑ Oh and what kind of whp does your butt dyno tell you are running?
lol
I still have stock injectors. And I talked to my butt after driving to work and he said feels like 180whp 😆
Dj WaRrIoRPuerto Rico · Sep 28, 2010#239 Originally Posted by
pimp my yaris ↑ I still have stock injectors. And I talked to my butt after driving to work and he said feels like 180whp 😆
to be honest i didn't read almost nothing on this thread but i just wanted to let you know that i did 188whp (forgot torque) at 8psi with t3 .42/.48 stock internals.. walbro 255 fuel pump with STOCK FUEL PRESSURE REGULATOR and 315cc injectors and apexi neo.. did a whole lot of ass whooping!!! i have to admit that i did alot of begginer mistakes but i learned and right now i'm rebulding my motor because my piston rings went soft on me but now i'm making some serious changes and going for 250-300 whp!!! woot woot!!! i'll be glad to answer any questions that nobody warned me about when i was in your shoes ;) (not talking about this forum, just tuners, friends, mechanics etc.) only thing holding me back is someone to show me how to install my emanage ultimate :( (already asked in another thread today)
GOOD LUCK!!
pimp my yarisThread starterchicago · Sep 28, 2010#240Ya I would love some forged pistons and rods. Mabe next summer. ^
sleey0PA · Sep 28, 2010#241How much does pistons,rods, and camshafts run?
Say, Crowers?
xbgodFlorida · Sep 28, 2010#242Crower Rods: 750.00
Arias forged Billet pistons: 800.00
Gude Cams:800.00 or complete head kit 1,950.00 w/O-ringed head.
Now you can factor labor or do it youe self, And save money but if you don't have the proper tools to include file fitting rings then add about 2,000.00 for labor.
XBG
xbgodFlorida · Sep 28, 2010#243Here is a Arias Forged Billet piston w/ Ceramic coating on a Billet Crower rod.
for our 1NZ-FE Motors
XBG
2 attachments not included in this copy
cali yarisCanoga Park, CA · Sep 28, 2010#244^ add head studs, race bearings etc. No use doing a build and leaving out stuff.
xbgodFlorida · Sep 28, 2010#245So true, this stuff will nickle and dime you to death.
XBG
sleey0PA · Sep 28, 2010#246Too rich.for my blood atm but awesome.none-the-less!
pimp my yarisThread starterchicago · Sep 28, 2010#247Anybody got a picture of a stock rod for comparison. I heard their pretty puuny! I tried to get a peek when my oil pan was off, but it was pretty dark
pimp my yarisThread starterchicago · Sep 28, 2010#248sleey0PA · Sep 28, 2010#249 Originally Posted by
pimp my yaris ↑
But the shafts need changed too. I heard they are as thin as a pencil!
pimp my yarisThread starterchicago · Oct 1, 2010#250Just ordered 255lph fuel pump to help with my lean problem.