I'd just recommend getting the bolts yourself and replacing them, it will save you and your wallet down the road.
Warning - Broken control arm bolt!
453 posts · 329,703 views · page 9 of 10
Replies continued
Scott, is that an official document of Toyota?
I called corporate this morning and for the second time I have talked to them they know absolutely nothing about this issue, and without a specific TSB number they were clueless. Both times I feel I was treated very rudely.
This is a safety problem and you think they would be a little more concerned about it!
Anyway apparently my VIN does not fall under this WARRANTY ENHANCEMENT PROGRAM even though my 2008 yaris sedan is clearly included in the vehicles covered. I asked the woman if she was unwilling to help me and she told me to take it up with the dealer.
I am in disbelief as how TOYOTA is treating this issue with me.
I called corporate this morning and for the second time I have talked to them they know absolutely nothing about this issue, and without a specific TSB number they were clueless. Both times I feel I was treated very rudely.
This is a safety problem and you think they would be a little more concerned about it!
Anyway apparently my VIN does not fall under this WARRANTY ENHANCEMENT PROGRAM even though my 2008 yaris sedan is clearly included in the vehicles covered. I asked the woman if she was unwilling to help me and she told me to take it up with the dealer.
I am in disbelief as how TOYOTA is treating this issue with me.
Toyota does not have a very good track record of helping people out with manufacturers problems. That being said no car companies really do.
Hence why it's just best to pick up the bolts and do it yourself. The more you know about the Yaris the less you need to rely on others to fix it.
Hence why it's just best to pick up the bolts and do it yourself. The more you know about the Yaris the less you need to rely on others to fix it.
That's what I'm more than likely going todo. I do all my own work anyway. I just wanted to have some satisfaction as to proving it to the dealer that I was correct with this issue, and also Toyota. I was thinking of getting a new Tundra down the road but not now......Originally Posted by tmontague ↑Toyota does not have a very good track record of helping people out with manufacturers problems. That being said no car companies really do.
Hence why it's just best to pick up the bolts and do it yourself. The more you know about the Yaris the less you need to rely on others to fix it.
What about a reliable low cost independent shop? Friends who could recommend one? I bought the bolts and had such a shop do mine and it was under $30.00 IIRC...might have even been under $20.00. I've had them do other little things like clean the rear brakes along with adjusting the parking break, etc. They are just insanely inexpensive. They've been in business since 1973 and have two locations. When I think "expensive metros where the cost of everything is 'driven up'...", I think the West Coast, the Northeast, and South Florida....not Texas or NE Ohio 🙂.Originally Posted by JTDBT903 ↑That's what I'm more than likely going todo. I do all my own work anyway. I just wanted to have some satisfaction as to proving it to the dealer that I was correct with this issue, and also Toyota. I was thinking of getting a new Tundra down the road but not now......
Originally Posted by JTDBT903 ↑Scott, is that an official document of Toyota?
I called corporate this morning and for the second time I have talked to them they know absolutely nothing about this issue, and without a specific TSB number they were clueless. Both times I feel I was treated very rudely.
This is a safety problem and you think they would be a little more concerned about it!
Anyway apparently my VIN does not fall under this WARRANTY ENHANCEMENT PROGRAM even though my 2008 yaris sedan is clearly included in the vehicles covered. I asked the woman if she was unwilling to help me and she told me to take it up with the dealer.
I am in disbelief as how TOYOTA is treating this issue with me.
Yes - That was an official bulletin to dealerships. The updated TSB numbers that I posted above are current and correct.
It is possible that your sedan is not included, as sedans are a different body and are built in a different factory, so they may have the seams sealed that are the cause of the issue.
I had received notices from Toyota regarding this issue for my 08 sedan.Originally Posted by CTScott ↑It is possible that your sedan is not included, as sedans are a different body and are built in a different factory, so they may have the seams sealed that are the cause of the issue.
I checked my bolts a month or so ago. After 5 years / 50KM in southern Ontario, The driver side bolt was like new, the passenger bolt was slightly rusted on surface. Some black liquid came out with the passenger one. I put vaseline (I had no grease) on them and reinstalled.
These were the original bolts based on the head markings.
Question: There are quite a few other bolts on front underside that look quite rusty (At least the heads do), should I be concerned about this?
These were the original bolts based on the head markings.
Question: There are quite a few other bolts on front underside that look quite rusty (At least the heads do), should I be concerned about this?
i just got to replacing the bolts for the new and improved. there is some difference in the stamping, probably improved strength, but don't know how to decode it (see picture).Originally Posted by CTScott ↑Toyota often seems to change part numbers, and sometimes with no visible change to the part (it could be something as simple as them changing suppliers for the part and hence revving the part number). I bought some of the 90119-14151 bolts and there does not appear to be any difference in strength rating, plating, etc. with the new part number.
I personally plan on checking (and perhaps replacing) the bolts once per year.
i did remove the old ones a couple of years ago to inspect, grease, and retorque. there was some superficial rust, but it didn't get any worse after nice greasing the whole length. in retrospect, i didn't need to replace it.
but, the car never saw any snow or ice. it would be very different in the salted roads states.

does anyone know where you could get the oem bolt? my car is way past the extended mileage and I want to replace it just because
I purchased mine thru Parts.com in USA
the original part # is 90119-14126
but 90119-14151 will work too.
the ones I removed from the vehicle looks ugly, but not as bad as others posted here, considering I'm in Canada where road salt is used in winters.

the original part # is 90119-14126
but 90119-14151 will work too.
the ones I removed from the vehicle looks ugly, but not as bad as others posted here, considering I'm in Canada where road salt is used in winters.


I got my replacement bolts through the dealership.Originally Posted by BobTheYaris ↑does anyone know where you could get the oem bolt? my car is way past the extended mileage and I want to replace it just because
Does anyone have a copy of T-SB-0078-12 ?
T-SB-0078-12.pdfOriginally Posted by NYC-SE ↑Does anyone have a copy of T-SB-0078-12 ?
Thank you Scott. I had a sneaking suspicion you would have it.
Just got around to replacing my control arm bolts.
2007 sedan with 180k miles on it. 10 years of exposure to Massachusetts' wintry conditions. They salt the living Jesus out of even the most slight winter precipitation here.
Pretty decent amount of rot on the neck of the bolt. Surprisingly my mechanic said the control arms themselves are doing alright. 🙇


2007 sedan with 180k miles on it. 10 years of exposure to Massachusetts' wintry conditions. They salt the living Jesus out of even the most slight winter precipitation here.
Pretty decent amount of rot on the neck of the bolt. Surprisingly my mechanic said the control arms themselves are doing alright. 🙇


Good thing you got them out when you did, mine looked about the same when I removed them 2 years ago
How concerned do you think us California kids have to be about this?
not very likely unless you live near the coast with a lot of ocean spray.
I'd swap them at the 10 year mark if I lived in Cali. Or to save money just pull your out and coat the threads with anti seize and then coat the whole thing in marine grease. That's what i did to my new ones and after 2 years not a single thing of rust on the bolt shaft
I'd swap them at the 10 year mark if I lived in Cali. Or to save money just pull your out and coat the threads with anti seize and then coat the whole thing in marine grease. That's what i did to my new ones and after 2 years not a single thing of rust on the bolt shaft
Thank you, sir!Originally Posted by tmontague ↑not very likely unless you live near the coast with a lot of ocean spray.
I'd swap them at the 10 year mark if I lived in Cali. Or to save money just pull your out and coat the threads with anti seize and then coat the whole thing in marine grease. That's what i did to my new ones and after 2 years not a single thing of rust on the bolt shaft
My 07 sedan is now 10.5 years old, and I live in Ottawa, Canada, where road salts are just a fact of life. Would it be a good idea to find a mechanic to replace the bolts, before it snaps? Seems like this potential problem would be the last remaining item that would limit the service life of my Yaris. It has only 130k km on it, and engine/transmission seems to be in good shape.
I'd soak those bolts in lube before trying to remove them.
The issue is accessing the threads to get a penetrating lube in there.
If you have impact tools if try yourself, if they snap drive cautiously to the nearest mechanic. If you don't have impact tools then just go to a mechanic.
I can't remember but I believe the solution if they snapped was to have a bit welded onto the stud which can then be removed.
If you have impact tools if try yourself, if they snap drive cautiously to the nearest mechanic. If you don't have impact tools then just go to a mechanic.
I can't remember but I believe the solution if they snapped was to have a bit welded onto the stud which can then be removed.
This is still an issue with 3rd gen cars. Below is a pic of the passenger side LCA bolt from my 2014 SE. I changed them out a week ago because the front end was making a clunking noise and I suspected that the LCA bolts were the issue. They were. No more clunking now. You can read about my adventure here:
Clunking noise over rough pavement
For those who suspect this may be an issue with their car: The only symptom I had was the clunking noise. The car rode, handled, steered, braked fine. Everything that you could see of the front suspension looked fine too. That's the problem, the LCA bolts are hidden. If you are in a heavy salt area and you are clunking you need to check the LCA bolts.
I was able to R&R the bolts with the car on the ground without a problem. As others here have suggested I coated the new bolts with a high quality calcium sulfonate marine grade grease before installing them. Should help for the future, but I'll be inspecting them every year going forward.
Toyota needs to update the TSB to include ALL model years and they need to extend the warranty on this to 3rd gen cars as well.
P.S. This thread needs to be made a sticky.
Clunking noise over rough pavement
For those who suspect this may be an issue with their car: The only symptom I had was the clunking noise. The car rode, handled, steered, braked fine. Everything that you could see of the front suspension looked fine too. That's the problem, the LCA bolts are hidden. If you are in a heavy salt area and you are clunking you need to check the LCA bolts.
I was able to R&R the bolts with the car on the ground without a problem. As others here have suggested I coated the new bolts with a high quality calcium sulfonate marine grade grease before installing them. Should help for the future, but I'll be inspecting them every year going forward.
Toyota needs to update the TSB to include ALL model years and they need to extend the warranty on this to 3rd gen cars as well.
P.S. This thread needs to be made a sticky.

FYI, I had also originally planned on pulling the bolts once per year but after coating them virtually the same as you and pulling them to inspect after 1 year, I now just check them every 2 years. Even at 2 years they're virtually untouched.Originally Posted by NYC-SE ↑I'll be inspecting them every year going forward.
It's your call but I figured I'd give my input to save you some hassle as your roads are similarly coated in brine for 4 months of the year like ours are.
I think I'll pull them in a year anyway just to satisfy my curiosity. I would expect them to be in good shape. After that probably every 2 years. I figure if they can survive for 3 years with no protection they should be fine after 2 with a good coat of grease.Originally Posted by tmontague ↑FYI, I had also originally planned on pulling the bolts once per year but after coating them virtually the same as you and pulling them to inspect after 1 year, I now just check them every 2 years. Even at 2 years they're virtually untouched.
It's your call but I figured I'd give my input to save you some hassle as your roads are similarly coated in brine for 4 months of the year like ours are.
toyota pig iron...I'll have to inspect mine after seeing this disaster
Well i finally checked mine on my 2007 and glad i did, the driver side was looking really bad. Well coated the new ones in grease and installed with no real drama.
I had my old mechanic in Ottawa switch mine out. My car is a 2008 and they were replaced in 2012-14 sometime ( I can't remember!) and snapped when they were extracting them. Luckily they welded on a bolt and were able to extract them that way!Originally Posted by RichardPan ↑My 07 sedan is now 10.5 years old, and I live in Ottawa, Canada, where road salts are just a fact of life. Would it be a good idea to find a mechanic to replace the bolts, before it snaps? Seems like this potential problem would be the last remaining item that would limit the service life of my Yaris. It has only 130k km on it, and engine/transmission seems to be in good shape.
I'd get on it ASAP!
I was able to get the bolts on my Yaris replaced. The passenger side came out without breaking. I wasn't so lucky with the driver's side.
The attached images are the driver's side bolt from a 2008 Yaris Hatchback after 10 years and 70K kms.
The new ones have been installed with lithium grease.. should last longer! 🙂

The attached images are the driver's side bolt from a 2008 Yaris Hatchback after 10 years and 70K kms.
The new ones have been installed with lithium grease.. should last longer! 🙂


My God, I think those are the worst I've seen yet!
How was the broken bolt extracted?
Yup, looks bad. I needed to drop the subframe and then heat up the bolt bolt with a propane torch. Once heated, I used a good pair of vise grips and was able to remove the bolt.Originally Posted by tmontague ↑How was the broken bolt extracted?
The most difficult part of this procedure was getting the control arm bushing to release the bolt since the bolt was rusted solid to the bushing sleeve.
I think this may happen because Toyota skipped a drain hole(s) somewhere. I did an oil change in dry conditions a day after I'd washed the car or there had been a rain event. Car on a lawn sloping somewhat nose down. Drove front wheels up on low ramps to level for oil change. Some time passed in steps of the oil change. And here's water dripping from that subframe area! (pretty sure I checked to see that it wasn't coming from the rubber HVAC tube)
(Warning - Broken control arm bolt! subframe Mind of Toyota)
(Warning - Broken control arm bolt! subframe Mind of Toyota)
I had the same issues on my '05 vibe when I replaced the control arms, took an extra 6hrs and I ended up having to burn out the bushing and enlarge the subframe hole to fit the metal insert through. It was seized so bad I never got it unstuck. An impact was useless as the bushing dampened the impacts.Originally Posted by yaris2011-07 ↑
The most difficult part of this procedure was getting the control arm bushing to release the bolt since the bolt was rusted solid to the bushing sleeve.
Now on any car I own I pull the control arm bolts and antiseize the whole thing so it never seized to the bushing sleeve. Takes some time but saves hours down the road
Agreed. Some extra drain holes or extra sealing to prevent water from entering the bushing sleeve would help to prevent this situation.Originally Posted by dogsridewith ↑I think this may happen because Toyota skipped a drain hole(s) somewhere. I did an oil change in dry conditions a day after I'd washed the car or there had been a rain event. Car on a lawn sloping somewhat nose down. Drove front wheels up on low ramps to level for oil change. Some time passed in steps of the oil change. And here's water dripping from that subframe area! (pretty sure I checked to see that it wasn't coming from the rubber HVAC tube)
(Warning - Broken control arm bolt! subframe Mind of Toyota)
I also ended up burning part of the bushing while lowering the subframe.Originally Posted by tmontague ↑I had the same issues on my '05 vibe when I replaced the control arms, took an extra 6hrs and I ended up having to burn out the bushing and enlarge the subframe hole to fit the metal insert through. It was seized so bad I never got it unstuck. An impact was useless as the bushing dampened the impacts.
Now on any car I own I pull the control arm bolts and antiseize the whole thing so it never seized to the bushing sleeve. Takes some time but saves hours down the road
I torched the bushing sleeve a number of times, so the heating and cooling process along with alot of hammering on the bushing sleeve helped to release it from the bolt.
I'm trying to show a local shop theses pictures and its useless linking this thread cause you dont display the images without signing up first.
thanks
thanks
Right click on the image.
Select "Copy"
Open Paint program
Select "New"
press Ctrl + V
Save file and copy it to your phone or tablet.
Show it to your mechanic and let him revel in the destruction.
Select "Copy"
Open Paint program
Select "New"
press Ctrl + V
Save file and copy it to your phone or tablet.
Show it to your mechanic and let him revel in the destruction.
We bought a '10 LB a couple of weeks ago with 126k on it. The 1st thing I did was change the oil to some M1 High Mileage 5/30. The 2nd thing I did while it was on the ramps was to check these infamous bolts. I was very nervous putting the breaker bar on them. Thankfully they both came out with out any drama. Despite water dripping from the passenger side hole when the bolt was removed, both bolts looked great. I lathered them completely in antiseize as well as the holes and reinstalled them.
I'm way out of warranty and on my own. So checking these will be part of my regular maintenance
I'm way out of warranty and on my own. So checking these will be part of my regular maintenance
Well I ordered the bolts.
Toyota argued with me about the part number and how they are non-returnable.
Apparently 90119-14126 was superseded by 90119-14144 and 90119-14151 wouldn't match up for him, he basically talked me into getting the 14144 bolts.
I pulled mine out, the drivers was pretty loose.
I then dipped the new bolts in marine grease from top to bottom and made sure they were really gooped up with excessive amounts of grease and put them in.
My car has under 45,000KM on it so they were not bad.
The bolts were $26 CAD for both.
I cranked the wheel to one side and layed beside the car to get them out without lifting it.
I wanted the garage to just inspect mine while getting a wheel alignment next week but decided to just replace them myself first.
The new ones only had 1 mark compared to 2 on the original.





Toyota argued with me about the part number and how they are non-returnable.
Apparently 90119-14126 was superseded by 90119-14144 and 90119-14151 wouldn't match up for him, he basically talked me into getting the 14144 bolts.
I pulled mine out, the drivers was pretty loose.
I then dipped the new bolts in marine grease from top to bottom and made sure they were really gooped up with excessive amounts of grease and put them in.
My car has under 45,000KM on it so they were not bad.
The bolts were $26 CAD for both.
I cranked the wheel to one side and layed beside the car to get them out without lifting it.
I wanted the garage to just inspect mine while getting a wheel alignment next week but decided to just replace them myself first.
The new ones only had 1 mark compared to 2 on the original.





those are in decent shape, keep them as spares just in case
the marine grease has worked well for me and I now only check them every couple of years as the water seems to keep away from the marine grease really well
the marine grease has worked well for me and I now only check them every couple of years as the water seems to keep away from the marine grease really well
Post.
exactlyOriginally Posted by Whiplash ↑Post.
I have some reading to do.
bumping up an old thread. I was installing some subframe collars today and pulled my control arm bolts I replace 3-4 years ago. I hadn't pulled them since 3 or so years ago. Well they look brand new with zero rust on them. All I did was coat the thread and the neck of the bolt in anti seize and then coat the neck in marine grade grease. The grease squeezes out when you tighten the bolts back up but that stuff is sticky and keep the water that pools in the area from contacting the metal.
apparently this is a great method of keeping the rust away.

this is after it was wiped off, it was crazy dirty.
Torque spec on the bolt is 118 ft/lbs
*take note* the bolt neck is what corrodes and snaps off so anti seize on the threads is a good idea for corrosion resistance but it will not fix the underlying rust issue with these bolts. Coat the bolt neck in marine great which is sticky as heck and will not allow water to sit against the metal and corrode it
apparently this is a great method of keeping the rust away.

this is after it was wiped off, it was crazy dirty.
Torque spec on the bolt is 118 ft/lbs
*take note* the bolt neck is what corrodes and snaps off so anti seize on the threads is a good idea for corrosion resistance but it will not fix the underlying rust issue with these bolts. Coat the bolt neck in marine great which is sticky as heck and will not allow water to sit against the metal and corrode it
Ah, thanks for reviving this thread. It reminds me that I need to check it on mine as well.
I have no idea whether my car can have this problem or not (VIN code: VNKKL98310A....) So it seems I have to go for visual inspection.
Local winters are salty so I may have some issue with this.
I have no idea whether my car can have this problem or not (VIN code: VNKKL98310A....) So it seems I have to go for visual inspection.
Local winters are salty so I may have some issue with this.
Hello Everybody,
I just got these two bolts replaced (TOYOTA Part #: 90119-14126) after dealing for some time now with a squeaking noise coming from the front suspension of my Toyota Yaris 2008 (Hatchback) while driving over a speed bump or an uneven surface.
I just came back home after driving it for 10 minutes around the neighborhood and the problem seems to be gone! :)
Tip: Before screwing the new bolts in, I submerged them in heavy duty grease to keep water and rust away for as long as possible.
I hope it helps all Yaris Owners out there!
RCRobymar.



I just got these two bolts replaced (TOYOTA Part #: 90119-14126) after dealing for some time now with a squeaking noise coming from the front suspension of my Toyota Yaris 2008 (Hatchback) while driving over a speed bump or an uneven surface.
I just came back home after driving it for 10 minutes around the neighborhood and the problem seems to be gone! :)
Tip: Before screwing the new bolts in, I submerged them in heavy duty grease to keep water and rust away for as long as possible.
I hope it helps all Yaris Owners out there!
RCRobymar.




I will add a bit of a curve ball to the front end issues with the Yaris.. it could be MORE than just the LCA bolts..
I have a 2009 Yaris HB 4dr LE with 180000 km (about 115000 miles).. almost exclusively highway and a 3 season vehicle. In the dead of a Manitoba/NW Ontario winter we drive a 2010 F--d Escape AWD.
In Oct, just before the Hamster (name we gave the Yaris) went into the garage for the winter I noted a constant clunking coming from the left front when going down gravel roads (I'm in central Canukistan..gravel IS considered an acceptable highway material and often better than asphalt).
After much checking I concluded (incorrectly) that it was the left inner tie rod end since grabbing the tie rod and yanking would get some movement ...so I bought a new inner TR end and the tool to remove/install it... In mid November (in the garage) I started work and found that it wasn't the inner TR, instead the drivers side mount for the steering rack had corroded and broken off, leaving the entire rack supported only by the pass side mount.
These are long 11mm (shaft dia) with a 17mm head (top) and 17mm nut on the bottom of the car.
The DS nut was hanging by dirt and rust and the whole rack would move with a small push/pull.... I was PI--ED OFF knowing it could have killed me at anytime and couldn't figure out what was up.
I unhooked the tie rods and the steering column then TRIED to remove the broken bolt from the D Side of the rack ....
well it's nearly unreachable as it mounted behind the steering input shaft (the designer should be beaten!) making getting a tool on it next to impossible... the PS is easy to get to.
Anyway after a ridiculous amount of frustration I got the rack out with the DS bolt still ruster into the bushings metal sleeve.. then into a 10 ton press (could NOT press it out) so then into a giant vise to hold the metal sleeve with a HUGE impact gun.. this finally got the bolt to spin in the metal sleeve and out it came (I'll post pictures).
I ordered new bolts and nuts ($42 CDN with taxes) and spent a day reassembling everything....
Well the Hamster came of the garage today as I set off for a front end alignment (tie rods had come off...) HOWEVER it STILL CLUNKED... just like before the steering rack odyssey so I turned around and put her (the hamster) back into the garage and set about searching this site and stumbled on this thread,,
I was able to get both mounting bolts out without breaking them and found them both in awful condition BUT not nearly as rusted as the steering rack bolts...
so.... I've ordered new 19mm LCA mounting bolts ($25 CDN) and will install those next week when they arrive from the centre of the Cdn universe ... Toronto :)
It would be wise to keep in mind they the idiots that brought you sh-t LCA bolts also did the same on the smaller and more fragile steering rack bolts...
btw..Toyota wanted $2200 (or more...its always more) to fix the rack...
I have a 2009 Yaris HB 4dr LE with 180000 km (about 115000 miles).. almost exclusively highway and a 3 season vehicle. In the dead of a Manitoba/NW Ontario winter we drive a 2010 F--d Escape AWD.
In Oct, just before the Hamster (name we gave the Yaris) went into the garage for the winter I noted a constant clunking coming from the left front when going down gravel roads (I'm in central Canukistan..gravel IS considered an acceptable highway material and often better than asphalt).
After much checking I concluded (incorrectly) that it was the left inner tie rod end since grabbing the tie rod and yanking would get some movement ...so I bought a new inner TR end and the tool to remove/install it... In mid November (in the garage) I started work and found that it wasn't the inner TR, instead the drivers side mount for the steering rack had corroded and broken off, leaving the entire rack supported only by the pass side mount.
These are long 11mm (shaft dia) with a 17mm head (top) and 17mm nut on the bottom of the car.
The DS nut was hanging by dirt and rust and the whole rack would move with a small push/pull.... I was PI--ED OFF knowing it could have killed me at anytime and couldn't figure out what was up.
I unhooked the tie rods and the steering column then TRIED to remove the broken bolt from the D Side of the rack ....
well it's nearly unreachable as it mounted behind the steering input shaft (the designer should be beaten!) making getting a tool on it next to impossible... the PS is easy to get to.
Anyway after a ridiculous amount of frustration I got the rack out with the DS bolt still ruster into the bushings metal sleeve.. then into a 10 ton press (could NOT press it out) so then into a giant vise to hold the metal sleeve with a HUGE impact gun.. this finally got the bolt to spin in the metal sleeve and out it came (I'll post pictures).
I ordered new bolts and nuts ($42 CDN with taxes) and spent a day reassembling everything....
Well the Hamster came of the garage today as I set off for a front end alignment (tie rods had come off...) HOWEVER it STILL CLUNKED... just like before the steering rack odyssey so I turned around and put her (the hamster) back into the garage and set about searching this site and stumbled on this thread,,
I was able to get both mounting bolts out without breaking them and found them both in awful condition BUT not nearly as rusted as the steering rack bolts...
so.... I've ordered new 19mm LCA mounting bolts ($25 CDN) and will install those next week when they arrive from the centre of the Cdn universe ... Toronto :)
It would be wise to keep in mind they the idiots that brought you sh-t LCA bolts also did the same on the smaller and more fragile steering rack bolts...
btw..Toyota wanted $2200 (or more...its always more) to fix the rack...
well it looks like I did some house cleaning and got rid of the steering rack bolt pics but here are the LCA bolts... the passenger side shaft has eroded (rusted away) more that the other but I'm glad I'm changing them..
If some needs to see the steering rack bolts I can take another pic ... I saved the bolts to show friends the crap Toyota put in these cars..
If some needs to see the steering rack bolts I can take another pic ... I saved the bolts to show friends the crap Toyota put in these cars..
