^ VERY nice 🙇
Yoda's Turbo Log
386 posts · 98,243 views · page 5 of 8
Replies continued
no 1zzOriginally Posted by cdydjded ↑Stock injectors?
sweeeet
At peak power, what duty cycle were the injectors running?
👍
I'd be careful with that turbo if I were you. No one wants to see a repeat of what happened to poor pimp. Otherwise, great numbers. 😁
I'd be careful with that turbo if I were you. No one wants to see a repeat of what happened to poor pimp. Otherwise, great numbers. 😁
dont kno what duty cycle for the injectors cali.
and to my surprise i have no shaft play at all. Feels just like knew and i was running without a bov for like 3 weeks before i got the greddy...
and to my surprise i have no shaft play at all. Feels just like knew and i was running without a bov for like 3 weeks before i got the greddy...
Sigh not enough power. Gonna get my engine built. So people talk about needing to upgrade axles when you hit 245 whp. So my question is upgrade to what? O and I am gonna shoot for 20 psi and then I will go for cosmetics
I wouldn't worry about axles unless you hit the dragstrip with slicks. Most of the time you won't have enough traction to break one.
Congrats on good hp numbers. I could never keep a stock motor in one piece at 150whp. Its crazy you got those numbers with 1zz injectors, I ran tC injectors maxed out to get 150whp but with stock fuel pump. Did you run a walboro perhaps?
Congrats on good hp numbers. I could never keep a stock motor in one piece at 150whp. Its crazy you got those numbers with 1zz injectors, I ran tC injectors maxed out to get 150whp but with stock fuel pump. Did you run a walboro perhaps?
Oh my. Anything specific that has made you want to do this? Lose a race, rode in a friend's faster car, or got a taste of "power" and want more?!?!?! 😁Originally Posted by Yoda ↑Sigh not enough power. Gonna get my engine built. So people talk about needing to upgrade axles when you hit 245 whp. So my question is upgrade to what? O and I am gonna shoot for 20 psi and then I will go for cosmetics
Agreed you probably don't need built axles, but I got mine from the Drive Shaft Shop:
http://www.driveshaftshop.com/
http://www.driveshaftshop.com/
Haha, you weren't kidding when you said that promotion meant A LOT of flex room. 👍
ya seriously!
Surfing eBay and came across these... FleaBay link
I think I know the company that makes those, I shot them an email. I would just worry about being the guinea pig!
is "Maxspeedingrods" the name of the company or is that just the ebay name?
Good stuff - I was under the impression the only rods for the 1NZ were made by that company XBG was getting them from. Can't remember the name atm.
Otherwise, those look like some nice big beefy rods. They should be able to take some abuse.
... That sounded pretty awful. 😆
Otherwise, those look like some nice big beefy rods. They should be able to take some abuse.
... That sounded pretty awful. 😆
That's what she said!!!! 🤣Originally Posted by Focus_Sh1ft ↑... those look like some nice big beefy rods. They should be able to take some abuse.
I was under the impression the only rods for the 1NZ were made by that company XBG was getting them from.We have Pauter and Crower here, and I know of at least two Chinese makers and one Malaysian one.
Stock pump buddy.Originally Posted by Blown_xa ↑I wouldn't worry about axles unless you hit the dragstrip with slicks. Most of the time you won't have enough traction to break one.
Congrats on good hp numbers. I could never keep a stock motor in one piece at 150whp. Its crazy you got those numbers with 1zz injectors, I ran tC injectors maxed out to get 150whp but with stock fuel pump. Did you run a walboro perhaps?
Well I rode in a buds stock Evo 8 and said I to myself need this tq. I don't race and floor it maybe 4 times a week.Originally Posted by PETERPOOP ↑Oh my. Anything specific that has made you want to do this? Lose a race, rode in a friend's faster car, or got a taste of "power" and want more?!?!?! 😁
Just want to gather ALL the parts first cause once I send out the engine I only have to do it once. going all top of the line for my baby :)
O noooozzz I got a little smoke coming out my engine somewhere :(. And its hotter than normal with my afr going lean at idle.Gonna check to see if i can locate the source with some seafoam.
😢
What was the smoke? Are U still running the same turbo?
it just stopped smoking one day and have not returned. and yea i am running the same turbo.
need to upgrade my spark plugs. any suggestions on what to choose. New dyno tune comming wednesday.....
squeezing the most out of this stock engine to see if i can get to 210whp..... getting close.
Geez bro! How much lbs of boost? 1zz fuel injectors? I need to still put my bigger injectors in and retune.
same injectors @10psi with open downpipe. Stripped out the back seats and all the liner also.
Props for being willing to push this engine to (what we believe to be) its limits. Hopefully this will shed some light on how much abuse a 1NZ can actually take.
Ditto, you convinced me to go to 8.5 psi.
I am gonna go 50psi when I boost...and then I will pick myself up along with the 1 million pieces of my yaris and not do it ever again...lol
Having problems with boost creep. Open dp is the cause so took the turbo off to port the wastegate a bit. Ordered a new actuator too. Pics to come later. Still hardly any shaft play ebay ftw this time.
pimp this is what you need here.
http://www.himni-racing.com/index.ph...roducts_id=687
pimp this is what you need here.
http://www.himni-racing.com/index.ph...roducts_id=687
^ What controller are you using?
Was not using a controller just a spring.
That explains the boost creep. You can pretty much nix that (and make more power sooner) with a controller.
Naw it was the open down pipe. It created a situation where it was easier for the exhaust gases to pass by the wastegate. And also not enough exhaust was flowing tru the dang thing to begin with. The hole was very small. I will upload the pics later today when I get off work.
I'm with Garm on this one. Boost creep or no boost creep - get a controller. If you set it up correctly it greatly aids in spooling. You do seem to be obsessed with getting as much power as possible 😉
Speaking of - are you still pushing 10 psi? If so how many miles has it been?
Speaking of - are you still pushing 10 psi? If so how many miles has it been?
Yea boost controller is in the works but just had to make it clear that it was not causing my creep.Originally Posted by Focus_Sh1ft ↑I'm with Garm on this one. Boost creep or no boost creep - get a controller. If you set it up correctly it greatly aids in spooling. You do seem to be obsessed with getting as much power as possible 😉
Speaking of - are you still pushing 10 psi? If so how many miles has it been?
Here are some pics of the porting job. Not bad for my first time. O sorry for the big pics😳
4 attachments not included in this copy
porting the waste gate is probably the best way to reduce boost creep. the other setup is to get a low psi spring and use a boost controller, but you can still get creep with that setup if you cant get the air out of your wastegate. i bet that porting helped!
Looks pretty thin on the one edge. Did you leave enough material there for the door to make a seat?
oh i didnt see that... hope it works fine for you.Originally Posted by Bluevitz-rs ↑Looks pretty thin on the one edge. Did you leave enough material there for the door to make a seat?
Yup it's just enough material left. It spools about 300 rpm faster than before. And sounds like a jet lol. The turbo is almost as loud as my exhaust... I need to get a vid up one of these days.Originally Posted by Bluevitz-rs ↑Looks pretty thin on the one edge. Did you leave enough material there for the door to make a seat?
Awesome :)
I think you may need to swap the final drive to get more torques on your wheels, eh Garm?
yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes
Need help to pick a new engine management. Scince I am trying to get the most out of this engine stock I need to upgrade form the Aem fic. Throw some names at me
AEM EMS?
GReddy Ultimate?
GReddy Ultimate?
Also what ignition upgrades should I be considering? Just coils? I already have one step colder plugs.
Hmm not sure about the ultimate with the cost of all the things you need to get it running the way you want it. You might be up there in cost with the standalone.
Hmm not sure about the ultimate with the cost of all the things you need to get it running the way you want it. You might be up there in cost with the standalone.
http://shop.microimageonline.com/All...-1NZX1-100.htm
If I was building my Yaris, this is the management I would choose - without a doubt. IT UTILIZES ALL OF THE STOCK WIRING/SENSORS. Just having a harness made for standalone management is probably over 1K in labor alone.
If I was building my Yaris, this is the management I would choose - without a doubt. IT UTILIZES ALL OF THE STOCK WIRING/SENSORS. Just having a harness made for standalone management is probably over 1K in labor alone.
that might be nice but who am i gonna get to tune that beast?