Yarisworld Archive

Yoda's Turbo Log

386 posts · 98,243 views · page 7 of 8

Replies continued

cali yarisCanoga Park, CA · Aug 12, 2012#301
fuel Regulators and gauges are in stock.
YodaThread starterFL · Aug 21, 2012#302
The shop that is working on my car in Miami are incapable of getting the job done in a timely manner.
I am still waiting on the engine to be put together after they have had my car for five months. Very very aggregated by them and going to pick up the car this Saturday. I will be taking over the project from now on. Nothing but lies and false promises. Very disappointed.
pimp my yarischicago · Aug 22, 2012#303
Originally Posted by Yoda ↑
The shop that is working on my car in Miami are incapable of getting the job done in a timely manner.
I am still waiting on the engine to be put together after they have had my car for five months. Very very aggregated by them and going to pick up the car this Saturday. I will be taking over the project from now on. Nothing but lies and false promises. Very disappointed.
That sucks. Get some engine assembly lube, feeler gauges, dial calipers and do it your self. Or find a quality engine builder. Someone who specializes in engine building. Make sure you have the piston and cylinder clearance checked closly. I have a lot of piston slap noise. Especialy when the engine is cold. It is making my nervous and Im not sure how this will effect reliaibility in the long run. The Cp pistons I bought are for a stock bore 1nzfe but I think they are to small. This seems to be a common problem with these pistons. The noise is only getting worse as the weather gets colder.
Bluevitz-rsOshawa, Ontario, Canada · Aug 22, 2012#304
There's a difference in the way cast pistons (OEM) expand vs. forged (CP). So the cold fitment is different causing more piston slap when cold.

Pimp, does the problem go away once up to temp?
cali yarisCanoga Park, CA · Aug 22, 2012#305
Yoda, which shop is it?
cali yarisCanoga Park, CA · Aug 22, 2012#306
The Cp pistons I bought are for a stock bore 1nzfe but I think they are to small.
If they were too small, and the right measurements were made, wouldn't you know that before you put them in? What tolerances did you use when you put the motor together?

Mine was done by a professional engine builder, as you suggested. So I'm curious to learn more about how you did it.
YodaThread starterFL · Aug 22, 2012#307
Originally Posted by cali yaris ↑
Yoda, which shop is it?
Small shop in Miami called RaceLab👎
fnkngrvIn The Hotbox · Aug 22, 2012#308
sad to see and hear...you will need to put the word out so that others don't suffer the way that you have done.
pimp my yarischicago · Aug 22, 2012#309
Originally Posted by Bluevitz-rs ↑
There's a difference in the way cast pistons (OEM) expand vs. forged (CP). So the cold fitment is different causing more piston slap when cold.

Pimp, does the problem go away once up to temp?
The noise does diminish when the engine is warm, but it never goes away.
pimp my yarischicago · Aug 22, 2012#310
Originally Posted by cali yaris ↑
If they were too small, and the right measurements were made, wouldn't you know that before you put them in? What tolerances did you use when you put the motor together?

Mine was done by a professional engine builder, as you suggested. So I'm curious to learn more about how you did it.
I did not have a proper bore guage. That is why I am stressing that it needs to be checked and double checked. I thought ordering a oem bore piston and using a stock unbored block would be OK. But it is very noisy and I am concerned about piston wall scoring or a piston skirt breaking. This is a perfect example of what my car sounds like when starting cold. My piston rings gap was checked and I am not burning any oil and the car runs great. Just very noisy. I have searched the net and it seems to be a common complaint with cp pistons.

http://www.youtube.com/watch?v=7NVjR...e_gdata_player
Blown_xaVirginia · Aug 22, 2012#311
Originally Posted by pimp my yaris ↑
I did not have a proper bore guage. That is why I am stressing that it needs to be checked and double checked. I thought ordering a oem bore piston and using a stock unbored block would be OK. But it is very noisy and I am concerned about piston wall scoring or a piston skirt breaking. This is a perfect example of what my car sounds like when starting cold. My piston rings gap was checked and I am not burning any oil and the car runs great. Just very noisy. I have searched the net and it seems to be a common complaint with cp pistons.

http://www.youtube.com/watch?v=7NVjR...e_gdata_player
Ive built probably 20 motors, unless you resleeve you pretty much need .5mm larger pistons. My motor has stock bore pistons, but I used a block with 5000 miles on it. Even then, the piston wall clearance is on the loose end of being acceptable after proper honing.

I know many people on here like to save a buck, but sometimes it is better to get a pre assembled shortblock. Many don't realize the work put into a shortblock, it isn't just pistons and rods thrown into a block. (not aiming this toward you)
YodaThread starterFL · Aug 25, 2012#312
Ok just picked up the car. Before I dive into the engine I need to find a top mount exhaust manifold. Any ideas?
packetraceQuebec · Aug 25, 2012#313
Originally Posted by Yoda ↑
Ok just picked up the car. Before I dive into the engine I need to find a top mount exhaust manifold. Any ideas?
a top mount manifold is a manifold that the flange is pointing upward ?

I have one to sell which have a t25 flange...it has been sanded and painted black recently...I sell it to have a downside one....

ill sell it for 100$ = shipping to you
Picture not included in this copy
YodaThread starterFL · Aug 25, 2012#314
The flange points up when you mount it right? I have one that points down if you need it. why r u selling that pretty thing lol.
Bluevitz-rsOshawa, Ontario, Canada · Aug 25, 2012#315
Originally Posted by packetrace ↑
I sell it to have a downside one....
Originally Posted by Yoda ↑
The flange points up when you mount it right? I have one that points down if you need it. why r u selling that pretty thing lol.
yup
packetraceQuebec · Aug 25, 2012#316
Originally Posted by Yoda ↑
The flange points up when you mount it right? I have one that points down if you need it. why r u selling that pretty thing lol.
Like I said i sell it to have a downside one :p i was going to buy the one from Garm with WG flange but i am
Interested to see yours :-)

Pm me!
YodaThread starterFL · Aug 26, 2012#317
the one i got is from Garm but it does not have the wg flange. Pics coming soon.
packetraceQuebec · Aug 26, 2012#318
Originally Posted by Yoda ↑
the one i got is from Garm but it does not have the wg flange. Pics coming soon.
PM sent😉
cali yarisCanoga Park, CA · Aug 26, 2012#319
you can always look at our online store for pics 😉

Picture not included in this copy
packetraceQuebec · Aug 26, 2012#320
yeah Garm I know how they are made...I could modify it to have the WG flange...and then bingo! :)
YodaThread starterFL · Aug 26, 2012#321
Here is a pic of it now. You have pm!

1 attachment not included in this copy

thefallsSunny place · Aug 27, 2012#322
Originally Posted by cali yaris ↑
you can always look at our online store for pics 😉

Picture not included in this copy
Beautiful!
YodaThread starterFL · Sep 8, 2012#323
Thanks packetrace got the manifold yesterday! There are a bunch of parts laying around in my room. Going to me redoing my piping with 2" from turbo to IC then 2.5" to TB.
Pic coming later.
packetraceQuebec · Sep 8, 2012#324
Hehe glad you like it :)

Looking forward to see pics!!:D
YodaThread starterFL · Sep 8, 2012#325
All this is on my floor right now about 1.5K worth of stuff.
Kings Performance is putting my engine together as i gather all the other small parts i need. Its getting pretty costly at this point 🙄

1 attachment not included in this copy

cali yarisCanoga Park, CA · Sep 8, 2012#326
^ yeah, that sorta just happens. 😆
packetraceQuebec · Sep 9, 2012#327
Are you going to weld piping together ?
YodaThread starterFL · Sep 9, 2012#328
Naw not really needed for the way I will have it setup. Just a can of hairspray will do lol.
packetraceQuebec · Sep 9, 2012#329
Ahahah what color ?
YodaThread starterFL · Oct 12, 2012#330
Ok so there is a problem. The shop in Miami whoever they used to do my engine fucked up. All the clearances are off. If I put it together now it's all gonna be loose. My options are at the moment is to sleeve it for $700 or get a new block and start over. Want to bash there heads in but it's an expensive learning lesson. Thinking I might just sleeve it n have it rock solid. But money is an issues now.
pimp my yarischicago · Oct 17, 2012#331
Originally Posted by Yoda ↑
Ok so there is a problem. The shop in Miami whoever they used to do my engine fucked up. All the clearances are off. If I put it together now it's all gonna be loose. My options are at the moment is to sleeve it for $700 or get a new block and start over. Want to bash there heads in but it's an expensive learning lesson. Thinking I might just sleeve it n have it rock solid. But money is an issues now.
Whats loose? Bearings, piston to bore clearance, ring gap some of this is fixable. If the engine is not in the car its not to late.

Then again a sleeved short block is also nice. I can tell you that will also have added expense as I am finding out. I really need a stand alone $$$$ to make the most out of my motor. My piston to bore clearance is a little loose but so far it runs great and does not burn a drop of oil :)
cali yarisCanoga Park, CA · Oct 17, 2012#332
Have you addressed this with the shop? What did they say? Can you post pics or some other proof of the screw up, something you could share with them? etc. etc.

The shop in Miami whoever they used to do my engine fucked up. All the clearances are off.
YodaThread starterFL · Nov 9, 2012#333
Originally Posted by cali yaris ↑
Have you addressed this with the shop? What did they say? Can you post pics or some other proof of the screw up, something you could share with them? etc. etc.
I washed my hands on that shop. Heading to the machine shop now actually so I will see if I can take done picks.
speed1Lecco-Italy · Jan 18, 2013#334
Originally Posted by ilikerice ↑
awesome, thanks for the clarification on that Focus.
Please,
be so gentle and tell me why u felt desire to go standalone than piggy?
I mean I first know piggy with stock oxigen sensors cannot do much.
But they sensors replaced by wideband sensor so stock denso ecu stands only like dead link from piggy to engine.
I have emanage ultimate and vmanage:
I don't need anybody's help to map from zero new ecu but I use stock base map as given and I modify reading wideband gauge.
Want u to tell me standalone is quicker?
My piggyes work at 8 bit like denso ecu.
Where I wanna go?
Please again,
I'm not engineer but it seems to me I don't need else better than I have.
God bless u to explain me I'm mistaken.
ilikericesavannah, ga · Jan 18, 2013#335
I have no issues with piggybacks, in fact I would rather go piggyback. I used Emanage blue on my crx for years and I like it because I know it. But I also don't want to have to reset my ecu every friday. I heard people say their ECU is auto-correcting the maps on piggybacks.

He obviously clarified that you can use a piggyback and there is nothing wrong with that, you just gotta do a bit more fooling the ecu than a standalone.

But honestly, the yaris hasn't been pushing me towards turbo as of late. I find myself wanting something a bit more, maybe go back to my crx, ek hatch and have been pondering building a turbo MKI mr2, I got a 4ag sitting in my garage right now.
speed1Lecco-Italy · Jan 18, 2013#336
Originally Posted by ilikerice ↑
ECU is auto-correcting the maps on piggybacks.
Ecu autocorrects just because of oxigen sensors along exhaust pipe line.
Sensors are good spies. Only they make their holy job.
U throw them away U don't mind them anymore.
That's what I've done.
Then U put to emanage numbers U need and engine goes what U want.
AFR Gauge is needed.
God bless all of Us.
YodaThread starterFL · Jan 21, 2013#337
Been gone for a minute but the project is back on. Had to use my fiances to help my family out and such. Engine is undergoing rebuild right now. Trying to decide if i should get it sleeved or not. I wont be pushing more than 300whp and I remember Blown Xa doing a few runs on that power level no problem. Also going to need a new manifold cause the ones I have don't suit the larger turbo well (no room).
speed1Lecco-Italy · Jan 21, 2013#338
Originally Posted by Yoda ↑
All this is on my floor right now about 1.5K worth of stuff.
Kings Performance is putting my engine together as i gather all the other small parts i need. Its getting pretty costly at this point 🙄
What paradise of turbo are u setting on yaris what boost pressure?
Stock piston e rod e head bolt?
mmmmmmmmm🙄
cali yarisCanoga Park, CA · Jan 21, 2013#339
YES. congrats in advance!
YodaThread starterFL · Jan 23, 2013#340
Originally Posted by speed1 ↑
What paradise of turbo are u setting on yaris what boost pressure?
Stock piston e rod e head bolt?
mmmmmmmmm🙄
Turbo is the GT28-rs up to 22 psi. Cp pistons and I beam Rods with all new head bolts.
speed1Lecco-Italy · Jan 23, 2013#341
Originally Posted by Yoda ↑
Turbo is the GT28-rs up to 22 psi. Cp pistons and I beam Rods with all new head bolts.
Great stuff..
But please,
I know turbo cars, I mean engines, have oil injectors under cylinder block to cool pistons...
1nzfe miss them...
Not the danger to blow very easy at 22 psi????
Indeed I'm really interested in turbo built, main choice to compete with 2000cc.
May tell me what revs turbo spool is and what revs top end power is?
I barely mean what u can expect not dyno I'm not interested in.
Sure gt28rs 22psiu make much more than 200hp.
Great stuff!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 😲
Blown_xaVirginia · Jan 28, 2013#342
Originally Posted by Yoda ↑
Been gone for a minute but the project is back on. Had to use my fiances to help my family out and such. Engine is undergoing rebuild right now. Trying to decide if i should get it sleeved or not. I wont be pushing more than 300whp and I remember Blown Xa doing a few runs on that power level no problem. Also going to need a new manifold cause the ones I have don't suit the larger turbo well (no room).
50,000 miles so far on factory sleeves, no excessive blow-by indicating cylinder distortion. Haven't done a leakdown test in a while, but the last one was good.
YodaThread starterFL · Feb 13, 2013#343
Do you think I need to get my IC piping welded? I could save about $500 just by cut and clamp. What worries my is the 20psi I will running. Open to suggestions
Focus_Sh1ftNew Jersey · Feb 13, 2013#344
Are you worried about blowing couplers off? My tC pushes 22 psi with silicone couplers and t-bolt clamps with no issues. I did have problems with a vacuum plug being blown off... That was fun. 🙄

Definitely opt for t-bolt over worm gear at that point.
cali yarisCanoga Park, CA · Feb 13, 2013#345
24 psi here, no issues with silicone couplings or fittings. A lot of clamps would make me nervous though.
pimp my yarischicago · Feb 14, 2013#346
20 psi and my couplers are holding. Are U running a FIC or a standalone? My FIC is maxed out at 20. 15psi atmosphere plus 20psi boost runs to the top of the FIC map at 35.
YodaThread starterFL · Feb 14, 2013#347
Running the fic still but if I am able to save a few here and there I will be upgrading to standalone. Garm did you have to modify anything to get your turbo to fit back there? Think I still have your manifold in my garage.
cali yarisCanoga Park, CA · Feb 14, 2013#348
^ I remember having to clock it, and I insulated the firewall, but otherwise it fits okay.

Remember, we now offer plug 'n play AEM EMS + Boomslang harness. Best of all worlds, and certainly the way I would have done it.
YodaThread starterFL · Feb 14, 2013#349
Ok cool I may take you up on that offer. My FIC is wired in gonna be a pain to remove .
Focus_Sh1ftNew Jersey · Feb 14, 2013#350
^ Just throw the bypass plug in and be done with it.