What's the price on that Aem Ems boomslang combo Garm? We need a YW discount.
Yoda's Turbo Log
386 posts · 98,243 views · page 8 of 8
Replies continued
^ Just throw the bypass plug in and be done with it.Yeah but then he's stuck with the FIC sitting there. Gotta be some resale value there!
True. I wonder if AEM sells just the universal harness (and if so, for a reasonable price).Originally Posted by cali yaris ↑Yeah but then he's stuck with the FIC sitting there. Gotta be some resale value there!
The thought of having to remove that harness after it's installed is worth no worldly sum of money to me for the effort involved, lol.
LOL i know right🙄Originally Posted by Focus_Sh1ft ↑True. I wonder if AEM sells just the universal harness (and if so, for a reasonable price).
The thought of having to remove that harness after it's installed is worth no worldly sum of money to me for the effort involved, lol.
Question did anyone need to change to tolerances when installing the pistons? I think it says 35 thousandths but not sure if it should be more for my boost level
Piston to wall clearance?
Yea that.Originally Posted by Bluevitz-rs ↑Piston to wall clearance?
It's different if you're using forged or cast pistons. Each has a different expansion rate so you'll have to do a bit more research to get it correct.
I went with the standard piston size. I beleve it was 75mm. I did not have a proper cyl. Bore guage. I have a little to much clearance. Noisy piston slap when the motor is cold. It gets a lot more quite when the motor is warm. It sounds like a old VW diesel. I have beaten the shit out of it with no problems yet. No oil burning at all. Its just sounds shitty when cold. Both Garm and blown xa said they have some piston slap noise. I beleve you can have some tighter tolerance on forged pistons as opposed to cast because they dont expand as much. This would explain my noise. I dont know what sizes you can by for custom cp pistons. I know 75 and 75.5 mm are available. Best to measure with a bore guage. And remember pistons are not perfectly round.
Pistons should be perfectly round. A worn cylinder bore might not be though.
I think we have 76mm also.
I have the 75.5 mm one. Might be getting a custom manifold made for the turbo. Cant fit it in there with the waste gate I was looking the the PT tuning one but not sure if it would fit back there.
Why doesn't it fit? I have the same manifold I sell and mine fits back there.
I have a internal wastage .
So my choices are as follows:
Order new external mani from MI and find an external WG
Have a manifold custom made
Sell everything and just get a new car lol.
This unforseen expenditure will delay me a bit longer.
Order new external mani from MI and find an external WG
Have a manifold custom made
Sell everything and just get a new car lol.
This unforseen expenditure will delay me a bit longer.
I have a internal wastage .They buy the one without a wastegate flange. It's offered both ways on our site. 🤷
Sorry if I was not clear. The internal wastegate is what is preventing it from fitting. It hits the firewall.
Last few parts I was waiting on have come in. New manifold and wastegate. Just one more thing to get... AEM EMS with pnp harness.😁 I cant wait😳
1 attachment not included in this copy
Finally got all of the parts needed. Engine done and going in.
About 2 more weeks of work.
About 2 more weeks of work.
1 attachment not included in this copy
looks awesome.
Went to the shop just to see how they were doing. Its pretty much all done but one problem is getting the TPS issue with the Haltech Sprint sorted out. The issues is that the Haltech is not reading the throttle position accurately. If he puts 50% throttle it reads between 70-100%. Tried a couple different settings but nothing seemed to fix it. Now were trying to figure out if it is tapped in the right location. I think its in C20-115 right now. Are there any other possible pin locations or settings I may have missed?😕🤷
Anyway here are a few pics🙄
Anyway here are a few pics🙄
2 attachments not included in this copy
what does it read a t closed throttle? sounds like it is off keyed but further testing would be needed to determine for sure.
Cant member what it was. I know the blitz guys use A21-55 for an input not sure it would work for me but I will try anything at this point. If I get this solved then by Friday i will pick her up.
Anyone have any ideas? Seems like the FI section went belly up.
Is this possibly a drive by wire issue? Are you still using the stock ECM for DBW?
Still using the stock ECU for DBW.Originally Posted by fnkngrv ↑Is this possibly a drive by wire issue? Are you still using the stock ECM for DBW?
Have you reached out to Carlos to ask him yet?
Nope did not. Did he have the Sprint 500 also? We are going to try A21-55 and hope for the best.Originally Posted by fnkngrv ↑Have you reached out to Carlos to ask him yet?
He's tapping the wire, not intercepting it, right?
I am pretty sure. I am going over there in a couple hours and will make sure every thing is set up right. Did my research on some possible causes. Really hope it can be resolved today as I just need a tune and this beast is DONE!
On another note... How is that Tc of yours?
On another note... How is that Tc of yours?
Alright so its about 90% done.
These are the problems I am having now:
-High Idle of about 1500rpm. I hoping the ecu relearns the idle. If not I will need to switch from DBW to cable.
-Car starts after 3 attempts every time all the time. Not sure why yet.
-AFR at idle is off the scale lean even tho the vacuum its dead on at 19hg. When we add more fuel it doesn't even move. The sensor is fine tho as it read accurately when tuning and when tested.
So hear are the numbers...259whp and 246tq @ 13.8psi on pump gas. Not sure how high I can go before I need water/meth so it was just tuned of the wastegate. I am driving it around to break it in and to see if the idle drops then its back to clean up the tune.
These are the problems I am having now:
-High Idle of about 1500rpm. I hoping the ecu relearns the idle. If not I will need to switch from DBW to cable.
-Car starts after 3 attempts every time all the time. Not sure why yet.
-AFR at idle is off the scale lean even tho the vacuum its dead on at 19hg. When we add more fuel it doesn't even move. The sensor is fine tho as it read accurately when tuning and when tested.
So hear are the numbers...259whp and 246tq @ 13.8psi on pump gas. Not sure how high I can go before I need water/meth so it was just tuned of the wastegate. I am driving it around to break it in and to see if the idle drops then its back to clean up the tune.
Great numbers that should make for a fun ride.
It's a bit scary actually lol. Love it!
Awesome man, I know the feeling with my tC (which is doing great, thanks for asking).Originally Posted by Yoda ↑It's a bit scary actually lol. Love it!
It's a very good problem to have 😆
So you wont be making it to the V2Labs Back to school bash tomorrow?
Almost there lol. Just need a new TB and that's it! Just installed my HID kit and lowered it a little. 250 more miles then I get to turn up the boost for some real power😁Originally Posted by 1.5 ↑So you wont be making it to the V2Labs Back to school bash tomorrow?