well? let's see some visual goodness!
Stay tuned
1,311 posts · 595,379 views · page 6 of 27
Replies continued
I am sitting at my office now waiting for the one person who can approve the check I need pay for the wrap. 😠 The guy that did it says it looks sweet.Originally Posted by cali yaris ↑well?
What was wrong with the previous wrap? 🙂 It looks pretty sweet to me... but then, what do I know? 🤷
That was actually paint. With this car going to SEMA, for the second time, Toyota had no intentions of just dusting off the old car and putting it in the booth. New project, new graphics. The only part that should be left over from its previous life will be the roll cage, and the header.Originally Posted by fmicle ↑What was wrong with the previous wrap? 🙂 It looks pretty sweet to me... but then, what do I know? 🤷
It looks way better now. 👏
Our new vinyl plotter just got delivered to the office. Now we can do all the detail work, and change some of the graphics as needed for the type of event the car is going to.
Should be looking good for its debut on the 14th.
Should be looking good for its debut on the 14th.
Time to head down to San Diego for the SCCA Solo National Tour. Won't be getting any work done on the Yaris this weekend. But at least I get to race something with some power. 😁
Late last night I got the headlight covers and flares back on, car is looking sharp. The Toyota transporter comes at 6:00pm to pick it up for its trip to the Staples Center. 😎
^^ BOUT TIME we have some exposure at one of these shows.....
On its way... There was also a Yaris sedan race car in the trailer. It was just a roller, looks like a project that never got finished. 🤷 The driver did not know much about it, just picked it up at one of the Toyota garages.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Found it... The 4-door was another past SEMA show car. The 2006 Street Image car. It has no engine and no brake calipers, but looks like a good start as it has an awesome cage - and air jacks. 🎉
http://www.urbanracer.com/features/p...-3-06/0406.jpg
http://www.urbanracer.com/features/p...-3-06/0406.jpg
nice splitter
Its time...
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
nice!
looks great. That lens makes the car look soooo long.
I think I liked the black headlights better. But the rest looks cool.
I liked the contrast the black offered, but it did not go with the theme Toyota wanted.Originally Posted by Bluevitz-rs ↑I think I liked the black headlights better. But the rest looks cool.
Picture not included in this copy
Ah, so this is Toyota's paint job then.
im more fond of the black as well, but the car looks real sick.
two thumbs up!
two thumbs up!
look neato
Nothing new to report... Spent most of he weekend at the LB GP. Our shock guy was in town for the race, unfortunately our shocks were not in his carry-on luggage. The shocks are still being worked over, and will have to catch another flight from the Netherlands.
Still have not had time to get the engine management installed. 🙁
We did get our new 20-9.5-13 Goodyear Eagle slicks. Just a tick wider than the 15s, at 10.5", and 3"s shorter. This will help fix our way to tall gearing, and drops a good deal of unsprung weight. Now if the wheels would just get here.
Looks like we will be running the same setup as the last few races when we head to Buttonwillow for the Double National this weekend. 🤷
Still have not had time to get the engine management installed. 🙁
We did get our new 20-9.5-13 Goodyear Eagle slicks. Just a tick wider than the 15s, at 10.5", and 3"s shorter. This will help fix our way to tall gearing, and drops a good deal of unsprung weight. Now if the wheels would just get here.
Looks like we will be running the same setup as the last few races when we head to Buttonwillow for the Double National this weekend. 🤷
I spent a huge portion of my time on the simulator vendors that were there. hahaha. I even had paddock passes.Originally Posted by Jason@SportsCar ↑Nothing new to report... Spent most of he weekend at the LB GP. Our shock guy was in town for the race, unfortunately our shocks were not in his carry-on luggage. The shocks are still being worked over, and will have to catch another flight from the Netherlands.
Still have not had time to get the engine management installed. 🙁
We did get our new 20-9.5-13 Goodyear Eagle slicks. Just a tick wider than the 15s, at 10.5", and 3"s shorter. This will help fix our way to tall gearing, and drops a good deal of unsprung weight. Now if the wheels would just get here.
Looks like we will be running the same setup as the last few races when we head to Buttonwillow for the Double National this weekend. 🤷
Finally got a shot of the Toyota display from the Staples Center.
Picture not included in this copy
Picture not included in this copy
^ Nice.
Look at the rust one the rotors of the sedan but a very cool pic!!!
Its sad actually. I want to buy it so I can restore it and finish what was started.Originally Posted by lilredrocket ↑Look at the rust one the rotors of the sedan but a very cool pic!!!
I know what you mean that is a very cool sedan there
Slight setback at Buttonwillow....
Qualified strong, 2nd, after skipping practice - this turned out to be dumb. When we read the sups for the event we both read it as we were running the same configuration as we normally use for every Natl race there, but this was not the case. So we were learning a new layout in qual and still ran fast.
Things were looking great during the race, should have been able to run for the win. But on lap 4 as I tracked out over the FIA curbing on corner exit something let go - a still unidentified part broke and made the car unsteerable, resulting in an a impact with one of the worker station walls. Lucky this was one of the slowest turns on the track, I was only going about 60mph when I realized I had a problem, and got it down to about 40mph on impact.
Took about an hour to pull off all the damaged body work, and most of the damage is just cosmetic. The uni-body is strait, and all the mounting points are intact.
So while we are waiting on these parts we are going to move our schedule up a couple of months and get the engine and trans work down now.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Qualified strong, 2nd, after skipping practice - this turned out to be dumb. When we read the sups for the event we both read it as we were running the same configuration as we normally use for every Natl race there, but this was not the case. So we were learning a new layout in qual and still ran fast.
Things were looking great during the race, should have been able to run for the win. But on lap 4 as I tracked out over the FIA curbing on corner exit something let go - a still unidentified part broke and made the car unsteerable, resulting in an a impact with one of the worker station walls. Lucky this was one of the slowest turns on the track, I was only going about 60mph when I realized I had a problem, and got it down to about 40mph on impact.
Took about an hour to pull off all the damaged body work, and most of the damage is just cosmetic. The uni-body is strait, and all the mounting points are intact.
So while we are waiting on these parts we are going to move our schedule up a couple of months and get the engine and trans work down now.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Ouch!!! Glad you are ok... Any pics of this part that broke?
Glad your ok, doesn't look too bad for 40mph collision.
Did the radiator break, or was it just taken off while ripping things down I assume the radiator supports were at least crumpled.
Did the radiator break, or was it just taken off while ripping things down I assume the radiator supports were at least crumpled.
ouch, i wanna know what broke...
So do I... It will take a bit more digging.Originally Posted by kngrsll ↑ouch, i wanna know what broke...
Unsteerable, as in turn the wheel and neither wheel turns, or does one of the two move?
As in the steering wheel locked, no turning.Originally Posted by CTScott ↑Unsteerable, as in turn the wheel and neither wheel turns, or does one of the two move?
The car does not have a column lock, has to be removed for Prod class, not that it would have mattered with the key in the ignition.
The power steering motor has also been removed, so I know it did not lock up.
Still early in the process, lots of parts to check. And we have lots of time, next Natl race is not until July.
Only bummer is we were planning to pull the slicks off and run one of the local autocross classes at the Cal Club Divisional in June, but the engine will likely still be in pieces at that point.
that makes me really nervous... we are pulling 85-90 mph on street tires with a lot of steering input on a couple corners here. im planning on running RA-1's at the next event so the speeds will be even higher.
I would not worry based on this one case. This could have been an issue just waiting from the cars previous life.Originally Posted by kngrsll ↑that makes me really nervous... we are pulling 85-90 mph on street tires with a lot of steering input on a couple corners here. im planning on running RA-1's at the next event so the speeds will be even higher.
We will figure it out and update.
But just in case... Stay off the FIA curbs. 😉
Did the steering unlock after the accident or was is it still locked?Do you have a manual rack or is the relay pulled on the factory power assisted rack?
Finally had a few spare minutes so I put together my video from the SCCA Solo National Tour in San Diego (April 10-11). My Saturday files took a dump, but here are the quick runs from CSL (my wife in an RX-8) and AS (the car owner and myself in his Corvette).
http://www.youtube.com/user/SportsCa.../0/IBpsxnBlE38
http://www.youtube.com/user/SportsCa.../0/IBpsxnBlE38
Glad to see you and the Yaris are OK .
Is that a Fluidyne or Koyo radiator ? Also where did you get the radiator hoses from ? I will be needing both of those soon .
Thanks
Is that a Fluidyne or Koyo radiator ? Also where did you get the radiator hoses from ? I will be needing both of those soon .
Thanks
Round two getting slowly under way... The new hood and intake system have shown up.
Plan is to get the trans out this weekend, and next week having the LSD rebuilt and the gears changed.
Now we just have to pull the trigger and pick which engine builder we are going to use. We have talked to everyone from the local guy we know, to an engine shop Toyota uses for ALMS/Rolex/Nascar. For the most part they are all starting at ground zero with a Yaris engine.
Hopefully during the tear down process we find our steering issue.
Plan is to get the trans out this weekend, and next week having the LSD rebuilt and the gears changed.
Now we just have to pull the trigger and pick which engine builder we are going to use. We have talked to everyone from the local guy we know, to an engine shop Toyota uses for ALMS/Rolex/Nascar. For the most part they are all starting at ground zero with a Yaris engine.
Hopefully during the tear down process we find our steering issue.
Did you get to the bottom of the steering lock issue yet?
Transmission came out on Saturday... Man that is so much easier when you don't have the front end on the car. 😆
Progress... New radiator and hoses arrived. Just visited the shop that is rebuilding the LSD and putting in the new gear set, should be done tomorrow. 😁
Going to be busy doing some driver coaching on Sat, but hopefully will be able to install the trans on Sun.
Going to be busy doing some driver coaching on Sat, but hopefully will be able to install the trans on Sun.
any word on the part that broke?
The transmission is back in. Freshly rebuilt Kaaz LSD ready to put power down. And the way to tall 3.722 final drive has been replaced with 4.312, this should help acceleration - even more so when we drop from the 23" Goodyear slicks to the 20" units. We should just about be able to launch in 2nd gear now.
I'm assuming you grabbed the 4.3 final from a C52/C56/C156 or similar? If so, did you just swap the Yaris bell housing onto the C5_ centre casing? Any problems with shifter cables etc?
My geuss is the wheel got suck up in the fender.Originally Posted by CTScott ↑Did you get to the bottom of the steering lock issue yet?
That seems like a lot of work... We found it much easier, and cheaper, to use the final drive and output shaft from an xB C50. 🤷 Direct bolt in. 👍Originally Posted by rob323 ↑I'm assuming you grabbed the 4.3 final from a C52/C56/C156 or similar? If so, did you just swap the Yaris bell housing onto the C5_ centre casing? Any problems with shifter cables etc?
The fenders are flared, not an issue. It was also nothing in the trans/lsd.Originally Posted by kou ↑My geuss is the wheel got suck up in the fender.
This has been very low on the priority list. As we take the car apart and prepare for the Runoffs we are checking the various parts.
We have found two questionable items that may be related to the problem, once we nail it down for sure I will post our findings.
I am just putting a feeler out to see if there is interested in OE style fiberglass front fenders...
After the recent mishap with our HP Yaris we are replacing all of the front body work. To meet the SCCA Production class rules we have to cover the tops of our 10.5" wide slicks, this has required the use of flares. I was talking to the vendor who supplies our flares about building a one-piece fiberglass fender, with the flare already built in.
This should cut some weight on the front of the car, and give us the tire clearance/coverage we need. The other option would be just a direct OE replacement with no flare, if you want the flares you just add them on.
I just did not know if anyone other than us would be interested in such a product. He should have a ballpark figure for me in the next week, and a minimum number needed to proceed - so far it sounds like six pairs.
The end result would look very similar to the image below.
Picture not included in this copy
After the recent mishap with our HP Yaris we are replacing all of the front body work. To meet the SCCA Production class rules we have to cover the tops of our 10.5" wide slicks, this has required the use of flares. I was talking to the vendor who supplies our flares about building a one-piece fiberglass fender, with the flare already built in.
This should cut some weight on the front of the car, and give us the tire clearance/coverage we need. The other option would be just a direct OE replacement with no flare, if you want the flares you just add them on.
I just did not know if anyone other than us would be interested in such a product. He should have a ballpark figure for me in the next week, and a minimum number needed to proceed - so far it sounds like six pairs.
The end result would look very similar to the image below.
Picture not included in this copy