Replies continued
kngrsllSpartanburg, SC · Dec 23, 2009#51these cars are so fun now bc they weight so little, i couldnt imagine actually doing a serious weight removal!
i had a 240 i raced for years, one night, we took EVERYTHING out that could unbolt other than the drivers seat, dash, and steering wheel. it was amazing, it was on lowering springs so it raised about an inch, and was ungodly fun to drive. we tried to put back as little as possible back in, but it wasnt quite the same
Jason@SportsCarThread starterDebary, FL · Dec 28, 2009#52Spent some time on the car over the holiday. Cut a bunch more unneeded sheet metal out of the car, and disabled the steering lock.
Started to pull some of the wires we no longer need, but what a mess. The previous builders liked to use the twist and tape method of wiring. 🤷 I doubt they actually built the car with this method, more likely in a hasty attempt to remove everything not bolted down (and some that were), they did this before they turned the car back over to Toyota. 😠
Also found out why the power steering does not work, two wires cut right at the unit in the dash. So far I have not been able to track down the other ends.
mojoyarisVancouver · Dec 31, 2009#53That FIA spec cage is probably overbuilt for the events. Are you able to mod it to make it lighter?
In a previous post, When the Tein Yaris was in Siphon, they took out the SC to make it a more even comparison to the old Spoon Fit. For most of the Time attacks that it was in, it was Supercharged. The cage is a heavy component of the car and some of those cars like th AJ racing Fit had the 1.5 but with turbo but no cage.
Another Fit had the K20 but the suspension setup was sloppy.
I heard that the Tein Yaris handled very well, but sadly didn't have the grunt that the other micro's had.
Love hearing about this car and glad it's going to good usage.
Jason@SportsCarThread starterDebary, FL · Dec 31, 2009#54 Originally Posted by
mojoyaris ↑ That FIA spec cage is probably overbuilt for the events. Are you able to mod it to make it lighter?
In a previous post, When the Tein Yaris was in Siphon, they took out the SC to make it a more even comparison to the old Spoon Fit. For most of the Time attacks that it was in, it was Supercharged. The cage is a heavy component of the car and some of those cars like th AJ racing Fit had the 1.5 but with turbo but no cage.
Another Fit had the K20 but the suspension setup was sloppy.
I heard that the Tein Yaris handled very well, but sadly didn't have the grunt that the other micro's had.
Love hearing about this car and glad it's going to good usage.
This is not an FIA spec cage, it is missing a number of mandated bars.
On one hand it is overbuilt per SCCA specs, with three extra bars that are not required. However, it was made with the minimum size tubing 1.5". Considering the small size of the tubes, I will happily keep the extra bars.
Just last week I installed the optional dash bar in our SSC class Nissan , 1.75" tube, it only weighed 7lbs. So even if I cut away all the extras in the Yaris, I might only save 30lbs, not worth it.
lilredrocketDFW, Texas · Jan 5, 2010#55What about the spare tire well? Cut it our and put in a flat piece of sheet metal to make it all flat?
jkuchtaL.A. · Jan 6, 2010#56PM me if you need interior tin work done. My shop is in Fullerton.
Jason@SportsCarThread starterDebary, FL · Jan 6, 2010#57 Originally Posted by
lilredrocket ↑ What about the spare tire well? Cut it our and put in a flat piece of sheet metal to make it all flat?
No plans to change it... Unless we have to run a fuel cell. We are legal with the OE tank, but if we cant run the car on fumes without fuel cut, we will install a cell.
Sitting at Beta Motorsports right now, as John builds our new exhaust. 😎
Only about ten days left to prep before the first race... There is way to much to do.
Doc ZaiusOttawa, ON, Canada · Jan 6, 2010#58This is a fun thread! 😁
Jason@SportsCarThread starterDebary, FL · Jan 7, 2010#59First race is right around the corner - pending my success in the garage this weekend - if anyone is around PIR (Phoenix International Raceway) Jan 16-18, stop by and check it out. Cost nothing to watch.
minired5stbySan Diego · Jan 7, 2010#60Have someone take lots of pics and video cause unfortunately I'm in Cali.
Jason@SportsCarThread starterDebary, FL · Jan 7, 2010#61 Originally Posted by
minired5stby ↑ Have someone take lots of pics and video cause unfortunately I'm in Cali.
We will be racing at Fontana the next weekend.
advocatelocation · Jan 8, 2010#62Good luck on the race! We're all cheering for you!
minired5stbySan Diego · Jan 8, 2010#63 Originally Posted by
Jason@SportsCar ↑ We will be racing at Fontana the next weekend.
Right on, I will try to make it out since its only an 1hr 1/2 away.
Jason@SportsCarThread starterDebary, FL · Jan 8, 2010#64lilredrocketDFW, Texas · Jan 8, 2010#65When are you coming close to Texas?
Jason@SportsCarThread starterDebary, FL · Jan 11, 2010#66NOOOOOOOOOOOOOOOOOOO 😢
I guess someone knew I was behind on my prep for this weekend, the race just got canceled. I guess they are replacing the catch fences at PIR and wont be done in time.
Picture not included in this copy
knowmercyOhio · Jan 12, 2010#67Seeing all this makes me want to go rip out the rest of my interior! Show cars are fancy and all, but when you see a car that's been properly setup for racing it's DEAD SEXY in my eyes! Too bad there isn't much of a SCCA scene up here in northeast ohio :( There is a local track (Nelson Ledges) but I don't think there are too many who'd do a submicro class.
Jason@SportsCarThread starterDebary, FL · Jan 13, 2010#68WOW... I just saw the proposed graphics package for the car, the art director for Racer magazine (who does all of our special project for Toyota) is building them, and the car will get a full wrap. 😎
They wont be installed until we are 100% done with the exterior, we still have to see how much fender work we need to fit the 10" wide slicks, but it will look sick - for a Yaris. 😉
cali yarisCanoga Park, CA · Jan 13, 2010#69"for a Yaris" -- sacrilege, ban him!
kidding.... 🙂 Jason do you know the car's weight yet?
Jason@SportsCarThread starterDebary, FL · Jan 13, 2010#70 Originally Posted by
cali yaris ↑ "for a Yaris" -- sacrilege, ban him!
kidding.... 🙂 Jason do you know the car's weight yet?
Less than when I started... But far from done. I would guess someplace in the 2000lb range right now, but with lots left to do.
cali yarisCanoga Park, CA · Jan 14, 2010#71I gotta go find a scale to put mine on, very curious.
justjesusOrange County · Jan 16, 2010#72Sorry to hear about PIR. When are you doing Fontana?
Jason@SportsCarThread starterDebary, FL · Jan 17, 2010#73Jason@SportsCarThread starterDebary, FL · Jan 19, 2010#74Well aside from rolling some fenders I had not done any bodywork in about 15 years, this weekend I had to tackle making a pair of covers to replace the headlights. The rules require the OE light assemblies are replaced with piece of an alternative material, likely a rule based on the very old British cars that we will be racing against that have glass lights.
So I picked up some fiberglass materials and used the old lights as a mold. Everything went very smooth. 😎
Just got our tires in today, waiting on these has held up the fender work to the point I am not sure we will make this weekend. Anyone try to fit a 10.4" wide slick on a Yaris yet? 😲
Picture not included in this copy
cali yarisCanoga Park, CA · Jan 19, 2010#75 Anyone try to fit a 10.4" wide slick on a Yaris yet?
yup, for drag racing
Jason@SportsCarThread starterDebary, FL · Jan 19, 2010#76 Originally Posted by
cali yaris ↑ yup, for drag racing
Got pics? Of course there is the small issue that we need to be able to turn, and have room for suspension compression. 😁
kngrsllSpartanburg, SC · Jan 19, 2010#77 Originally Posted by
Jason@SportsCar ↑ Got pics? Of course there is the small issue that we need to be able to turn, and have room for suspension compression. 😁
😆 i thought about saying something like that
Jason@SportsCarThread starterDebary, FL · Jan 20, 2010#78Well, knowing that I would likely have to cut the fenders to fit the big tires anyway, I went at it last night with the fender rolling tool. Not even close to enough clearance with a big roll. We are going to have to break out the cut off tool and do a little slice and dice.
More parts are arriving daily, but this weekend looks like a long shot. 🙁
We built our last project car in eight weeks, and I thought I could beat it. But I guess five weeks was unrealistic.
cali yarisCanoga Park, CA · Jan 20, 2010#79 i thought about saying something like that
I'm glad you didn't say something like that. 😆
these are 14 x 8, with a 15mm spacer, but not 10, so I was incorrect about that part! ...but you get the idea. no problem with turning radius with these.
Picture not included in this copy Picture not included in this copy Picture not included in this copy Jason@SportsCarThread starterDebary, FL · Jan 20, 2010#80 Originally Posted by
cali yaris ↑ I'm glad you didn't say something like that. 😆
these are 14 x 8, with a 15mm spacer, but not 10, so I was incorrect about that part! ...but you get the idea. no problem with turning radius with these.
Not much room for suspension compression there.
Even with the 10.4" wide tire I can get enough turning radius. The issue is going to be suspension travel. So we will cut the fenders, and then decide if we need to flare, or just leave it open.
cali yarisCanoga Park, CA · Jan 20, 2010#81well you said this:
Got pics? Of course there is the small issue that we need to be able to turn, and have room for suspension compression.
so I responded about the turning radius.
What are you using for springs and shocks/struts?
Jason@SportsCarThread starterDebary, FL · Jan 20, 2010#82 Originally Posted by
cali yaris ↑ What are you using for springs and shocks/struts?
We are having shocks made. Springs, very short and stiff. 😉
cali yarisCanoga Park, CA · Jan 20, 2010#83if you're going full stiff, you shouldn't need a whole lot of travel, right?
What about the springs? Any details?
kngrsllSpartanburg, SC · Jan 20, 2010#84yeah, i would love to see that set up... mind taking pics before you install the components??
that car looks mighty good with those big ole front tires. i think i may need to get some spacers for my 15x7's +25's so i can flare my fenders some more 😁
Jason@SportsCarThread starterDebary, FL · Jan 20, 2010#85 Originally Posted by
cali yaris ↑ if you're going full stiff, you shouldn't need a whole lot of travel, right?
What about the springs? Any details?
You would be surprised at how much even a stiff car travels.
On this car we tripled the OE spring rates, and there was enough body roll on street tires to tuck them in the fenders.
http://www.youtube.com/user/SportsCa.../1/tgjRt6_cxVk cali yarisCanoga Park, CA · Jan 20, 2010#86I see that big tuck about 00:56. I know nothing about RX-8's though.
Is that a 'no' on the details of your springs? I'm sure the racing community on here (and not just me) is quite curious about the details of your set up.
Jason@SportsCarThread starterDebary, FL · Jan 20, 2010#87 Originally Posted by
cali yaris ↑ I see that big tuck about 00:56. I know nothing about RX-8's though.
Is that a 'no' on the details of your springs? I'm sure the racing community on here (and not just me) is quite curious about the details of your set up.
And it can be worse on the road course, I like using the curbs. 😁
Details will be in SportsCar.... However, these things always seem to come out after the issue is in people hands. 😉 But part of it is not being 100% on the rates right now. The shock builder will give us a range to start with, and then it will be determined by laps times, and the but dyno.
justjesusOrange County · Jan 21, 2010#88Cool video of the RX-8. Looks like you're using a Go-Pro?
I'll need to pick up an issue of SportsCar.
Hmm. This weekend in Fontana. I will try and make it out. :) (to watch)
Jason@SportsCarThread starterDebary, FL · Jan 21, 2010#89 Originally Posted by
justjesus ↑ Cool video of the RX-8. Looks like you're using a Go-Pro?
I'll need to pick up an issue of SportsCar.
Hmm. This weekend in Fontana. I will try and make it out. :) (to watch)
Yes, we have a number of GoPro cameras here, both the wide and normal view. Great product for the price. Our only gripe has been the audio. This weekend we will have the new HD version in the Sentra that my boss is racing, and the audio is reported improved over the past units.
Now if UPS does not bring me some Toyota parts in the next few hours, the Yaris wont be seeing the track this weekend. 🙁 Worst case I will tow it up there on Sun to get the log book and annual tech out of the way, but it wont be race ready.
Jason@SportsCarThread starterDebary, FL · Jan 22, 2010#90Well I am sitting at the office waiting for parts to be delivered, when I should be at the track getting ready for practice. 👎
Things are not looking good for a race this weekend. But, while I have been here we set up a test day in mid Feb. This will help prevent the trial by fire, which we would have experienced by racing the car this weekend.
I was not thrilled by the idea of the cars first outing being a National Club Race. The more I work on the car the more frightening it is. The twist and tape wiring I found early on was only the tip of the iceberg. Last night I found the top mounting bolt on the left front strut was finger tight.
Looks like we have all the shock dimensions nailed down, and with any luck we should see them in about six weeks. 🤤
justjesusOrange County · Jan 23, 2010#91 Originally Posted by
Jason@SportsCar ↑ Yes, we have a number of GoPro cameras here, both the wide and normal view....
I got a wide version (they were out of normal). I love it. Same gripe as you: sound! Now, if I can only remember to mount/use it at the autocross events! Same with my MaxQData. ugh.
Originally Posted by
Jason@SportsCar ↑
Things are not looking good for a race this weekend...
Looks like we have all the shock dimensions nailed down, and with any luck we should see them in about six weeks. 🤤
shucks. I cleared my Saturday. Sunday, well, that was already clear :)
Sorry to hear about this weekend, and your iceberg.👎
YIKES. Six weeks? Where's the smiley that passes out?
kngrsllSpartanburg, SC · Jan 24, 2010#92what spring rates did you end up running? i am currently running 375 F and 342 R on Tokico HTS's with a 23 mm rear sway bar... curious to hear what you guys run.
jekqmbSTL · Jan 24, 2010#93Garm your car looks amazing on slicks! You better be going to Import Alliance this year!
Good luck with the tires Jason, i think you guys can pull it off! Also got any updated pics of your progress as of now?
mojoyarisVancouver · Jan 25, 2010#94I'm curious to see how this is all going to come through.
10 in wide eh?
Jason@SportsCarThread starterDebary, FL · Jan 27, 2010#95So Sunday came and went without the Yaris leaving the garage. I did go to AAA Speedway on Sunday to watch last years project car race (Nissan Sentra SER Spec V, that was built for Showroom Stock C for only $3k). My boss (Philip) ran the car in the SSC Natl race, qualified 2nd and finished 2nd - I was very happy to see he was lapping 1 sec slower than I ran in the car last June. 👍
Yesterday we had a "work from home day" so I could nail done the rest of the items to get our car SCCA Club Racing legal. Finally we are log book ready and can start racing the car. Fire system, kill switch, seat, belts, wheel, pedals and preliminary bodywork are done. 👍
Philip also came down to "help", instead he built a new exhaust for the Sentra, this only cost me about an hour of my time. 😆
Making the bumpers secure without all of the mounting hardware, and crash beams was a project. The fiberglass headlight replacements seemed to take forever, but they are on - they still need to be finish sanded and painted, they are in primer right now.
We have yet to cut the fenders, so we are sitting on some old Kumho V710s, rather than our race slicks. Trying to determine how much to cut when we don't have our suspension yet is a bit of a gamble. But we will probable go ahead and cut them to fit the slicks now, and deal with further fender messaging after our suspension shows up.
Picture not included in this copy
Picture not included in this copy
cali yarisCanoga Park, CA · Jan 27, 2010#96Looking very good man! Aww... my old bumper...
Is that a stock radiator?
Jason@SportsCarThread starterDebary, FL · Jan 27, 2010#97 Originally Posted by
cali yaris ↑ Is that a stock radiator?
No, its a Koyo. It came with the car, and we cant see any reason to change it.
Jason@SportsCarThread starterDebary, FL · Feb 1, 2010#98We just got back from the SCCA natl convention in Vegas. 😎 Had a chance to talk with a number of people involved with the Prod class rules making. Found out we were misinterpreting our wheel allowance... We thought we had to run 15x7 wheels, but it turns out that is the max size for our car in HP. So we are putting off the fender cutting until we have a chance to test fit a 13x7.
Going to a 13" changes our tires from a 23" diameter to 20". This will change our effective final drive by a good margin, lowers the car 1.5" without screwing up the geometry, and would drop another 20lbs from the car. Yet we still maintain a 10.4" tire width. 👍
I did have some time to kill so I removed my first rear side window. Covered it in some spare vinyl and gave it a good whack with a rubber mallet. That was fun, and way quicker than removing it the correct way. Now I just have to cut and fit the plastic replacement.
I have continued trying to convince the SEB/PAC (Solo rules makers) to move the Yaris from EP to GP, as it is way underpowered for EP, but no luck. They want to see how it pans out in HP Club Racing before they risk upsetting GP with a newer car. 🙁 So we will likely skip autocrossing this car on the natl level, and strictly focus on road racing.
cali yarisCanoga Park, CA · Feb 1, 2010#99I have some V2 13x8 wheels here if you're interested.
Jason@SportsCarThread starterDebary, FL · Feb 1, 2010#100 Originally Posted by
cali yaris ↑ I have some V2 13x8 wheels here if you're interested.
I might have to send Philip over there to pick one up for a test fit. 😉