Off to load the car up. Tomorrow it gets the aluminum flywheel and new clutch/pressure plate setup.
Stay tuned
1,311 posts · 595,379 views · page 5 of 27
Replies continued
Didn't look like the rear end came up so much as the front end just DOVE. Maybe a little more compression damping (or spring rate) in the front is in order?
how does an aluminum flywheel fit into your class? I'm still so confused about what you can do and can't do.
Everything you ever wanted to know about SCCA Production class rulesOriginally Posted by cali yaris ↑how does an aluminum flywheel fit into your class? I'm still so confused about what you can do and can't do.
Loren, I race in SCCA. I've read through the rules more than once. Why would I post the question if I could find it (easily) in the rulebook?
If Jason doesn't have time to answer, he won't answer, and that's fine. Seems to me, there has been plenty of helpful posting about keeping the car within the rules.
If Jason doesn't have time to answer, he won't answer, and that's fine. Seems to me, there has been plenty of helpful posting about keeping the car within the rules.
I looked at the link I posted and found the answer very quickly. Any flywheel the same size or larger than stock is permitted in HP. I don't understand your angst.
His flywheel will surely be within the rules for his class.
His flywheel will surely be within the rules for his class.
Upon further consideration, I think I see the problem. Garm, do you "race" with SCCA or do you "autocross" with SCCA? There's a big difference. Jason is building a "race car" in accordance with the SCCA "GCR" (General Competition Rules), which is the road racing rule book. I'm guessing what you've read is the SCCA Solo II rule book, which is a completely different animal and does not apply in any way to the car that Jason is building.
i really like NASA's TT rules... its a points based system. I am going to do a few events in TT-F this year,
Loren posted the applicable section, and as he inferred the Solo and Club Racing rules are typically different. Even more confusing in some cases due to the class acronyms being similar, but having different meanings - Solo P=Prepared, Club Racing P=Production.Originally Posted by cali yaris ↑how does an aluminum flywheel fit into your class? I'm still so confused about what you can do and can't do.
However, in our case (HP limited prep, Level 2) our rule set is very similar to the GP Solo rules. Unfortunately the Solo Events Board elected not to allow the Yaris in GP, so we can not competitively race our car in HP trim in Solo - it goes to EP, where it is way under prepared, and way under powered.
In a nut shell:
Body - Car is gutted and has a minimum 6 point cage. On-board fire system, kill switch, race seat, 5-point harness, window net. Drivers and pass side windows must be removed. All other glass can be replaced with plastic, 1/8" for side and rear, 1/4" for windshield. Hood and hatch/trunk may be replaced with composite units. Bolt-on fenders may be replaced with composite ones. Uni-body (rear) fenders may be cut and flared, composite may be added. Crash support beams behind bumpers can be removed.
engine - Level 2 prep must keep stock throttle body and fuel injection (injectors, fuel pump and regulator can be replaced, you just cant change the TB or manifold) . We can do port matching, valve job, cams, compression bump with a limit set by SCCA (we still have not received our spec, but most every car can go +1 pt), over-bore, balance & blueprint. CAI, header, no emission, exhaust just needs to exit behind the driver and be under 103db @ 50'. Engine management is open.
trans - if we use a stock trans no issues, shifter is open, clutch/pressure plate and flywheel are mostly free (no carbon multidisc units). We can also change ratios and use dog engagement, but you get a weight penalty. Final drive is open. LSD is open.
brakes - must use OE front caliper. Front rotor can be changed to a two-piece (aluminum hat), but must be stock size, and can not cross-drilled or slotted. Rear may be converted to disc, but can not be larger than the front OE brakes, and the rear rotor must be a solid non-vented disc. Brake lines, pads and master cylinder are open.
Suspension Level 2 prep - Stock pick up points (you cant move the rear beam mounts like many Yaris owners like to do 😉 ), shocks are open, springs are open but must be in the OE location (this means no coil-overs in the rear, but you can use an adjustable perch fitted in the stock location). Swaybars are open. Bushings are open. Camber adjustment is open.
Wheels and tires - 15"x7" max wheel size for the Yaris, smaller is ok. Any tire that you can fit on the wheel, but the top of the tire must be covered by the bodywork.
Minimum weight for the Yaris in HP is 1900lbs (w/driver) using a stock trans.
There is more, but those are the basics.
The NASA system works well for the people who show up off the street with a car that is already setup. Take some time to look at the book and plan the build of a car from scratch, it will get expensive fast - especially if you take the time to test the various points combos to see which is the fastest.Originally Posted by kngrsll ↑i really like NASA's TT rules... its a points based system. I am going to do a few events in TT-F this year,
With SCCA everyone in the same class gets the same mods. You can only spend so much.
Jason, thanks that is really clear.
Can you use TRD or solid engine mounts? Those work really well in my car.
Also consider the 23mm sway bar, it's +4mm over the TRD one.
Can you use TRD or solid engine mounts? Those work really well in my car.
Also consider the 23mm sway bar, it's +4mm over the TRD one.
Yes, we can change the engine and trans mounts. I should have had them done while the clutch was being changed and the trans was out. Oh well, we can do them when we pull the motor later in the season.Originally Posted by cali yaris ↑Jason, thanks that is really clear.
Can you use TRD or solid engine mounts? Those work really well in my car.
Also consider the 23mm sway bar, it's +4mm over the TRD one.
We put an adjustable bar on the rear.
What are you doing posting on here... You should be in Fontana. 😁 KJ just brought his STX RX-8 by the house for a tire change, he killed his tires in the AM session. Now he is all set for Sun.
I should be out there, for sure! I'm going tomorrow.
The trans mount alone will make a very big difference and it's an easy bolt-on.
The trans mount alone will make a very big difference and it's an easy bolt-on.
New hood installed this weekend, just a tick under 5lbs. I have not weighed the stock hood yet, so I don't know how much weight this saved.
Also replaced the wing windows with plastic.
edit: I just noticed how bad this makes the head light covers look now, I need to sand and paint them. :)
Picture not included in this copy
Also replaced the wing windows with plastic.
edit: I just noticed how bad this makes the head light covers look now, I need to sand and paint them. :)
Picture not included in this copy
Going to take the Yaris up to Thunderhill for the Double National this weekend.
Currently five entries in HP, and the group up there is plenty fast.
We would have liked to have gotten more done since the last race, but the car is a little lighter, and we have made some small suspension changes. Should be fun.
http://www.sfrscca.org/component/opt...999999/cid,22/
Currently five entries in HP, and the group up there is plenty fast.
We would have liked to have gotten more done since the last race, but the car is a little lighter, and we have made some small suspension changes. Should be fun.
http://www.sfrscca.org/component/opt...999999/cid,22/
I like the hood, did you guys make it or is this a potential future product from someone.
We modified an existing product to suit our needs. We managed to cut its weight by about 35%, and installed the AeroCatch system.Originally Posted by markitect ↑I like the hood, did you guys make it or is this a potential future product from someone.
stock Yaris hood is 12.75 pounds.
Those are cool latches, did you make something to hold the pins? I couldn't get them to line up.
Those are cool latches, did you make something to hold the pins? I couldn't get them to line up.
Cool, we pulled around 8lbs off the front.Originally Posted by cali yaris ↑stock Yaris hood is 12.75 pounds.
Those are cool latches, did you make something to hold the pins? I couldn't get them to line up.
I just ran a piece of flat stock from the OE hood cushion mount to where I needed the pins to end up.
I wanted to mount them the other direction (90 degrees from what you see) but you can only get 5 degrees of tilt out of them and still have the pins engage. By putting them sideways you have a lot more flexibility, and they are way easier to line up.
Just got back from another round of tune-up and tuning. Started at Toyota HQ with a "health check" for the car, trying to get rid of our CEL for the crank angle sensor. No luck. The TSB for that only applied to 07+ cars, and the reflash could not be used on our 06'. They did test the CAS and everything was good, so we will just have to live with the light if it comes on again.
Then back to the tuner for some more dyno runs. A little more tweaking to the camcon found a few more HP over what we had at Willow Springs. Hopefully that and the new clutch/flywheel combo will get us around Thunderhill quickly this weekend.
Then back to the tuner for some more dyno runs. A little more tweaking to the camcon found a few more HP over what we had at Willow Springs. Hopefully that and the new clutch/flywheel combo will get us around Thunderhill quickly this weekend.
So from what you've seen with the gains from the Camcon, would you recommend it as a worthwhile performance increasing mod?
I don't believe anyone has used a Camcon extensively with the Yaris so I'm curious to hear some feedback on it to see if it's a viable mod to squeeze out some more HP out of our car. 🙂
I don't believe anyone has used a Camcon extensively with the Yaris so I'm curious to hear some feedback on it to see if it's a viable mod to squeeze out some more HP out of our car. 🙂
I don't know what one cost versus some of the more complex units, but both our tuner and myself were surprised by the gains that could be had with it - it looked like ebay stuff to me, and I expected nothing out of it. While it does lack some key tuning abilities that the higher end units offer - and we will be upgrading in the next month to something more versatile - it does make power.Originally Posted by Gideon ↑So from what you've seen with the gains from the Camcon, would you recommend it as a worthwhile performance increasing mod?
I don't believe anyone has used a Camcon extensively with the Yaris so I'm curious to hear some feedback on it to see if it's a viable mod to squeeze out some more HP out of our car. 🙂
I will have to fire up my lap top to look at the sheets, but I seem to recall a more than 10hp and tq difference between the unit being off and on. There are not to many bolt-ons that will make that kind of power. It works. But we know there is more in the programming, power that the Camcon wont unlock.
Thanks for the information. I've seen a lot of talk in regards to it with other Toyota engines, but never any sort of hard information, just butt dyno readings. 😆
Checked the files, 11.1lb-ft tq and 13.2hp, on a Dynapack.Originally Posted by Gideon ↑Thanks for the information. I've seen a lot of talk in regards to it with other Toyota engines, but never any sort of hard information, just butt dyno readings. 😆
I am beat. What a long weekend and a long drive.
Thunderhill is a great track, lots of elevation changes, and really tuff off camber turns. The track was a little slow for our car, for most of the turns we were pulling out in 3rd gear just out of the power band, and shifting to fourth on the fastest straits resulted in almost no acceleration because they were uphill runs. 😠 Watching a Fiat X19 pull away from you uphill sucks. But the good part was hearing a Honda guy complain about getting beat by a Yaris. 😁
Two more podium finishes, 3rd both days, out of six cars - and lucky to finish at all on Sunday, as the dreaded misfire came back. We believe the car is experiencing fuel starvation, we are generating enough grip and body roll with the slicks that at even 1/2 tank the car will cut under certain conditions. This happened three times during the weekend, and in all the cases the mis went away and car was good after about half a lap. Time to look at getting a fuel cell.
Thunderhill is a great track, lots of elevation changes, and really tuff off camber turns. The track was a little slow for our car, for most of the turns we were pulling out in 3rd gear just out of the power band, and shifting to fourth on the fastest straits resulted in almost no acceleration because they were uphill runs. 😠 Watching a Fiat X19 pull away from you uphill sucks. But the good part was hearing a Honda guy complain about getting beat by a Yaris. 😁
Two more podium finishes, 3rd both days, out of six cars - and lucky to finish at all on Sunday, as the dreaded misfire came back. We believe the car is experiencing fuel starvation, we are generating enough grip and body roll with the slicks that at even 1/2 tank the car will cut under certain conditions. This happened three times during the weekend, and in all the cases the mis went away and car was good after about half a lap. Time to look at getting a fuel cell.
are you adjusting a/f, vvt or both w/ the camcon for power #'s?
VVT and fuel trim.Originally Posted by thebarber ↑are you adjusting a/f, vvt or both w/ the camcon for power #'s?
Just make sure you're monitoring oil pressure as well. I'm sure you know the same thing can happen inside the oil pan too. 😉Originally Posted by Jason@SportsCar ↑...we are generating enough grip and body roll with the slicks that at even 1/2 tank the car will cut under certain conditions. This happened three times during the weekend, and in all the cases the mis went away and car was good after about half a lap. Time to look at getting a fuel cell.
I have the same problem with fuel starvation and since the car is setup to run lean, after a good hot run, she just runs out of gas and is pooped. This only happens when I'm running the car 90/90 (90% of power bandwidth, 90% of the time).
Time for a piggy back, bigger injectors, fuel pump and Throttle body.
Time for a piggy back, bigger injectors, fuel pump and Throttle body.
Video from the Saturday race: http://www.youtube.com/watch?v=Q2ELSIuIIq4
I just saw the video u posted on YT.Originally Posted by Jason@SportsCar ↑I am beat. What a long weekend and a long drive.
Thunderhill is a great track, lots of elevation changes, and really tuff off camber turns. The track was a little slow for our car, for most of the turns we were pulling out in 3rd gear just out of the power band, and shifting to fourth on the fastest straits resulted in almost no acceleration because they were uphill runs. 😠 Watching a Fiat X19 pull away from you uphill sucks. But the good part was hearing a Honda guy complain about getting beat by a Yaris. 😁
Two more podium finishes, 3rd both days, out of six cars - and lucky to finish at all on Sunday, as the dreaded misfire came back. We believe the car is experiencing fuel starvation, we are generating enough grip and body roll with the slicks that at even 1/2 tank the car will cut under certain conditions. This happened three times during the weekend, and in all the cases the mis went away and car was good after about half a lap. Time to look at getting a fuel cell.
-When the misfire appears, does your throttle respond only if u press it lightly? 😕
-Goes away a few seconds later? 😕
-Does you Check engine light blink? 😕
Sorry for asking too much but I'm having a random misfire and the car does the same buzzing sound (not too nice to hear 😠 ) when it occurs. And it happens after a long drive (1.5-2 hours) averaging 80-90mph specially when shifting from 3rd to 4th gear
Time for a piggy back, bigger injectors, fuel pump and Throttle body.YES
We think the issue is the tank/pickup, as we only had this problem in Turn 6.Originally Posted by mojoyaris ↑
Time for a piggy back, bigger injectors, fuel pump and Throttle body.
Certainly a new fuel pump, one with a better pickup design could help, if that is in fact the issue.
But putting more demand on the fuel system with some of those other parts could make the issue worse.
Piggy back is in the works. We can not touch the throttle body. And we are looking at fuel cell options.
Those would solve jason's problem, but would they work on my case?Originally Posted by cali yaris ↑YES
And now that Fuel Pumps are mentioned, I got my fuel pump and hose replace because they were "deformed", the dealership took care of it, can it be that the fuel pump is damage again?
Throttle position seems to be irrelevant, the engine is flat no matter the input.Originally Posted by YarisPR ↑I just saw the video u posted on YT.
-When the misfire appears, does your throttle respond only if u press it lightly? 😕
-Goes away a few seconds later? 😕
-Does you Check engine light blink? 😕
Sorry for asking too much but I'm having a random misfire and the car does the same buzzing sound (not too nice to hear 😠 ) when it occurs. And it happens after a long drive (1.5-2 hours) averaging 80-90mph specially when shifting from 3rd to 4th gear
It does not go away a few seconds later, takes more like a 30-60 secs depending on the severity.
CEL was flashing, but no code was stored during the Saturday occurrence. On Sunday the issue was bad enough to keep the CEL on and we pulled P0300, P0301, P0302 and P0304 - all misfire codes.
In our case this happened in Turn 6 at Thunderhill each time. Previous to T6 you are dropping down a big hill (the video does not do the elevation justice) in to a medium speed (3rd gear) right hander, then just a slight lift for the left (T6) and this is where the starvation would occur.
We think that all of the fuel is loaded to the drivers side rear of the tank previous to T6, then the lift and sudden left turn pulls all the fuel to the passengers side front of the tank, and this is enough to get the pump to suck some air even at half a tank.
Jason, can u confirm if what I wrote earlier happens to you? cause the syptoms are the same and u probably find the answer sooner than me 😁Originally Posted by Jason@SportsCar ↑We think the issue is the tank/pickup, as we only had this problem in Turn 6.
Certainly a new fuel pump, one with a better pickup design could help, if that is in fact the issue.
But putting more demand on the fuel system with some of those other parts could make the issue worse.
Piggy back is in the works. We can not touch the throttle body. And we are looking at fuel cell options.
We had the exact same problem with a '89 Honda CRX at Mosport International Raceway in turn 5B. Only it didn't set the check engine light. It would just misfire for a second or two. And it only occurred if we had less than 1/2 tank of gas. We later had problems with oil pressure in the same corner but that set a code and VTEC shut off.
Edit:
It is possible that the ECU is going into fail safe to try and save your non existent cat because of the misfire. The CEL is flashing to warn you of imminent damage to the cat due to the misfire. I've had this happen with my Echo on the track, but I don't have TBW, so it possible the ECU is cutting back the throttle.
Edit:
It is possible that the ECU is going into fail safe to try and save your non existent cat because of the misfire. The CEL is flashing to warn you of imminent damage to the cat due to the misfire. I've had this happen with my Echo on the track, but I don't have TBW, so it possible the ECU is cutting back the throttle.
I don't think we are experiencing the "same" problem. On Saturday this happened well into the race, with two laps to go, and less than a 1/4 tank of fuel. On Sunday I got on lap 3 with half a tank, and then again near the end of the race when the low fuel light was on - but always in the same turn.Originally Posted by YarisPR ↑Jason, can u confirm if what I wrote earlier happens to you? cause the syptoms are the same and u probably find the answer sooner than me 😁
The easy fix for us may be to start with more fuel. But the right thing to do would be a fuel cell.Originally Posted by Bluevitz-rs ↑We had the exact same problem with a '89 Honda CRX at Mosport International Raceway in turn 5B. Only it didn't set the check engine light. It would just misfire for a second or two. And it only occurred if we had less than 1/2 tank of gas. We later had problems with oil pressure in the same corner but that set a code and VTEC shut off.
Edit:
It is possible that the ECU is going into fail safe to try and save your non existent cat because of the misfire. The CEL is flashing to warn you of imminent damage to the cat due to the misfire. I've had this happen with my Echo on the track, but I don't have TBW, so it possible the ECU is cutting back the throttle.
Yeah, fuel cell FTW... literally HAHA
if you do a pump, will you do a return line?
I don't think we can, we have to use the stock fuel injection - less the injectors - so I don't think we can alter the fuel rail.Originally Posted by cali yaris ↑if you do a pump, will you do a return line?
All part of the challenge of find a cell that will work with our car. New racecar development is fun. 👍🙁
Are you allowed to do a small surge tank?
Yes.Originally Posted by largeorangefont ↑Are you allowed to do a small surge tank?
Fingers crossed, should be getting the new engine management today... Going to make for a busy weekend. Tuesday the car goes in for the new graphics.
If anyone finds themselves at the Lakers VS Clippers game on the 14th, the Yaris will be there on display in the Toyota both. 👍
Between the graphics and ecu work there will be little time left to work on the suspension, but it should be here before our Apr 24-25 double national at Buttonwillow.
Now where are my wheels?????
If anyone finds themselves at the Lakers VS Clippers game on the 14th, the Yaris will be there on display in the Toyota both. 👍
Between the graphics and ecu work there will be little time left to work on the suspension, but it should be here before our Apr 24-25 double national at Buttonwillow.
Now where are my wheels?????
My Editor has created an "unofficial" SportsCar magazine website to catalog our past projects. It currently covers a couple of our past project cars as well as some other fun projects.
In the future we will be adding more images, as well as more current cars (like the Yaris, after it prints in the magazine).
http://sportscarmag.wordpress.com/
In the future we will be adding more images, as well as more current cars (like the Yaris, after it prints in the magazine).
http://sportscarmag.wordpress.com/
My car would cut out just like yours did. Alot of the other posters in the forum would give all kinds of advice but really don't think they were running their car 10/10ths.
You run your car pretty hard and the fuel starvation seems to be a natural part of the Yaris due to it's nature to run ....lean.
Hope you find out the fix for it while staying within the boundaries of your class. Good luck!
You run your car pretty hard and the fuel starvation seems to be a natural part of the Yaris due to it's nature to run ....lean.
Hope you find out the fix for it while staying within the boundaries of your class. Good luck!
The Yaris is being wrapped right now, will be ready in the AM. Cant wait to see it. 👍