Yarisworld Archive

Stay tuned

1,311 posts · 595,379 views · page 3 of 27

Replies continued

cali yarisCanoga Park, CA · Feb 1, 2010#101
as you wish! 🙂
Doc ZaiusOttawa, ON, Canada · Feb 2, 2010#102
Hi Jason,

I recently dug out my copy of Siphon #1, and checked out the article on the Tein Yaris. I thought you might find some of it interesting:

...
In order to offset the weight of the full cage, TEIN even went as far as to remove all excess hardware and wiring. Chase [Philip Chase, TEIN USA sales and marketing manager] regaled us with stories of clipping wire harnesses out of the car, later crossing his fingers as he turned the ignition, hoping that the extricated wires were in fact as non-essential as he believed.
...
😳

Take care... and good luck with your build & racing! 👍
Jason@SportsCarThread starterDebary, FL · Feb 2, 2010#103
Originally Posted by Doc Zaius ↑
Hi Jason,

I recently dug out my copy of Siphon #1, and checked out the article on the Tein Yaris. I thought you might find some of it interesting:

😳

Take care... and good luck with your build & racing! 👍
Well that explains the missing OBDII port. The people doing our new dash/data system are thrilled about doing it from scratch, rather than just plug and play. 😠

Seems odd that they would ditch the useful stuff, then install 12lbs of 0 gauge wire and a 35lb battery. 🤷
Doc ZaiusOttawa, ON, Canada · Feb 2, 2010#104
Originally Posted by Jason@SportsCar ↑
Well that explains the missing OBDII port. The people doing our new dash/data system are thrilled about doing it from scratch, rather than just plug and play. 😠

Seems odd that they would ditch the useful stuff, then install 12lbs of 0 gauge wire and a 35lb battery. 🤷
Maybe it b/c they actually had this sales and marketing manager guy doing all the work! lol 😁
Jason@SportsCarThread starterDebary, FL · Feb 9, 2010#105
Had a productive weekend... Both of the rear side windows have now been replaced with 1/8" plastic for a nice weight savings. I pulled the headlight covers to add another layer of fiberglass, they are much stiffer now, and I was able to close up some of the gaps around the edges.

Got our fender flares and did a mock up, should give us just enough width to cover the tops of the tires, but with out making the car super wide.

Friday we have our log book inspection being done. And Sun we are off to the track for our first test session. 👍
cali yarisCanoga Park, CA · Feb 9, 2010#106
what wheels and tires are being used?
Jason@SportsCarThread starterDebary, FL · Feb 9, 2010#107
Originally Posted by cali yaris ↑
what wheels and tires are being used?
For our test day we are going to burn up some old 205-50-15 Kumho V710s, mounted on 15x7 Motegi Traklite wheels - these are off of the SportsCar ITA Miata project car.

We have some 15x7 Kosei K1 TS wheels, wrapped in 23-9-15 Goodyear Eagle Sports Car Specials (10.4" wide bias ply cantilever slicks) ready to go, but we are still looking at making the change to 13"s for the gearing advantage.
Jason@SportsCarThread starterDebary, FL · Feb 12, 2010#108
It's always something. 😠 Getting ready to load up for our tech inspection... And the alternator is bad. No I have to try and pick one up on the way to the office.

300 miles on this car and the alternator fails. 😕
90tsimissouri · Feb 12, 2010#109
that sucks a fat one. ive installed tons of "new" junk parts.... starters alternators...etc im enjoying your updates on yalls project
Jason@SportsCarThread starterDebary, FL · Feb 12, 2010#110
😠😠😠😠😠

I was not able to pick up the alt on the way in... My wifes fourth flight of the week to NY got canceled for tonight. So I had to run in early so I can go home at 10:00 and take her to the airport. Car will have to wait for a few hours.

In more fun news, the Yaris makes a cameo in this news story: http://www.ocregister.com/video/?vid...pId=1125901233
Jason@SportsCarThread starterDebary, FL · Feb 12, 2010#111
Time to start drinking 🍻. None of the usual places have a rebuilt alt for the Yaris, and with a rebuilt going for $200 I don't want to call the dealer - and don't have time to get one from our usual Toyota channel. So I guess I will brave using a local re-builder that tells me he can get it done today. 🤷
Bluevitz-rsOshawa, Ontario, Canada · Feb 12, 2010#112
With all the cut wiring did you check to make sure there's power going to the IC on the alternator before deeming it a dud? The centre wire should have 12V with the car running. (Black with a red tracer is what I have in my '05 Echo wire diagram. Should be the same in the Yaris I hope.) You can use a cheap steel needle as a back-probe.
Jason@SportsCarThread starterDebary, FL · Feb 12, 2010#113
Originally Posted by Bluevitz-rs ↑
With all the cut wiring did you check to make sure there's power going to the IC on the alternator before deeming it a dud? The centre wire should have 12V with the car running. (Black with a red tracer is what I have in my '05 Echo wire diagram. Should be the same in the Yaris I hope.) You can use a cheap steel needle as a back-probe.
Everything worked fine any time we have started it in the last month.

But we just had the alternator tested, and it checks out. Might be the kill switch. No I get to start chasing wires.
90tsimissouri · Feb 12, 2010#114
just cuz the alternator checks good the regulator could be out in it... ive had that happen a few time in an old dsm and hondas ive worked on.. but if you have done as much harness modding as it appears wouldnt hurt to give it a real close once over.
Jason@SportsCarThread starterDebary, FL · Feb 12, 2010#115
So I pulled the dash cover and checked the wires on the kill switch (alt and batt both run in/out of it). They all were tight, but the batt light went off and I had 14v at the batt. I went ahead and tightened all the leads, even though none were loose. At this point hopefully the issue is gone, or it will show up at our test day and we can nail it down before the first race.

I think the kill switch may be bad internally.

Also had a chance to weigh the car. Down to 1934lbs (from 2176lbs when we got it), and we are not done yet. Goal is to hit 1850lbs without driver - still puts us over our minimum weight, but so far it is lighter than I expected.
90tsimissouri · Feb 12, 2010#116
glad to hear hopefully it wont be a on going gremlin.
justjesusOrange County · Feb 13, 2010#119
Damn, that's light!

Nice pooch. And nice way to make the paper :)
cali yarisCanoga Park, CA · Feb 13, 2010#120
1934 is very good, I think that's the lightest one we know about.
Jason@SportsCarThread starterDebary, FL · Feb 15, 2010#121
Had our test day. We ended up on the Street of Willow, our friends at the Fast Lane racing school ( www.raceschool.com ) let us slide in between student session. 👍

First session went pretty good, did some easy laps to seat the new brake pads, and to make sure nothing was going to fall off. We were also trying to run the car out of gas, no knowing how old or what was in the tank.

Near the end of the session the car started to mis and lack power, also got a CEL. I figured we had finally run it out of gas for the most part. Pulled in to the pits and dropped in a couple gallons of 100oct unleaded.

Turning off the kill switch reset the computer and things went ok for about half a lap. Then CEL, and the car would not go over 35mph.

Checked the fuel pressure, it was a solid 40psi. Pulled all the plugs, they looked like new. Started checking wiring - this was the one good part of the day - hidden in the birds nest of wires tucked in the base of the A pillar was the OBDII port that I thought had been removed (how and why it ended up there I will never know). 👍

We scanned and found code P0301, misfire in cylinder #1. Now we just have to figure out which if the twelve things that can cause that problem it is. 🙁

All in all we had a good day. The car seemed to handle OK, even on very used up V710s. The brakes worked good. I need to adjust the brake pedal a little to help with heel/toe - the brake pedal is a little to low. No smoke came out of the car. The oil and water are all clean. And most important, nothing fell off.

Now we have two weeks before the first natl race for the car. I sure am glad we found this problem on our test day, would have sucked to this happen in a race.
cali yarisCanoga Park, CA · Feb 15, 2010#122
solid CEL or blinking CEL?

40 psi fuel pressure seems a little low if that was under load.

working out the kinks, that's a good thing. Streets are fun in a Yaris.
Jason@SportsCarThread starterDebary, FL · Feb 15, 2010#123
Originally Posted by cali yaris ↑
solid CEL or blinking CEL?

working out the kinks, that's a good thing. Streets is so fun in a Yaris.
Solid. Fuel pressure was checked at idle and at 3krpm. I tend to think the problem is fuel related. The car sat as long as two years, with who knows what in the tank, and crapped out right as I get to the bottom of the tank. Step one, pull the fuel pump.
Bluevitz-rsOshawa, Ontario, Canada · Feb 15, 2010#124
Originally Posted by cali yaris ↑
solid CEL or blinking CEL?

40 psi fuel pressure seems a little low if that was under load.

working out the kinks, that's a good thing. Streets are fun in a Yaris.
Yeah I've had a blinking light before on a track day. Checked the code and found a cyl 2 misfire. But I think it was caused by too much limiter under part throttle.

I was told by one of my buddies from Toyota Canada that the flashing light indicated a lean condition and the Cat could potentially be damaged (melted).
Jason@SportsCarThread starterDebary, FL · Feb 15, 2010#125
Originally Posted by Bluevitz-rs ↑

I was told by one of my buddies from Toyota Canada that the flashing light indicated a lean condition and the Cat could potentially be damaged (melted).
We don't have one.
Bluevitz-rsOshawa, Ontario, Canada · Feb 15, 2010#126
Originally Posted by Jason@SportsCar ↑
We don't have one.
Then are you running a different ECU? Or have you modified the signal going to the ECU to make it think there's a cat?

Because if the cat has been taken out with a stock computer, it'll set a code every time.
Jason@SportsCarThread starterDebary, FL · Feb 15, 2010#127
Originally Posted by Bluevitz-rs ↑
Then are you running a different ECU? Or have you modified the signal going to the ECU to make it think there's a cat?

Because if the cat has been taken out with a stock computer, it'll set a code every time.
That would be a different code. 😉
Bluevitz-rsOshawa, Ontario, Canada · Feb 15, 2010#128
The missfire could be caused by the cat delete. The reduced backpresure could be the cause. The ECU could be retarding the timming due to the code and that the lack of power.
Jason@SportsCarThread starterDebary, FL · Feb 15, 2010#129
Originally Posted by Bluevitz-rs ↑
The missfire could be caused by the cat delete. The reduced backpresure could be the cause. The ECU could be retarding the timming due to the code and that the lack of power.
The cat does not show up on my list of possible causes. 🤷
Bluevitz-rsOshawa, Ontario, Canada · Feb 15, 2010#130
You have to think of it this way...

... with less back-pressure you get more exhaust out of the cylinder on the exhaust stroke, but the intake charge is still the same on a N/A motor. (ok, not EXACTLY the same due to valve overlap and the effect that has on pulling in air, but basically the same.) The intake charge will be "cleaner" than what a stock ECU is programmed for. The stock A/F ratio is based on the back-pressure being there and the amount of residual exhaust gasses still left inside the cylinder on the intake stroke.

A very simple cheat to make the ECU run richer is to trick it into thinking the engine is colder that it really is. If you add a resistor to the Water Temp Sensor and make the ECU think the engine is only running at 110°F or so it'll think it needs more fuel for running in the cold weather. (this might also set a code for the thermostat, but it's nothing major.)

Another method is to add a resistor to the intake temp sensor in the MAF meter. You can trick it into thinking it's sucking in air at -40°. This should have the same effect, but with less chance of setting a code.
Jason@SportsCarThread starterDebary, FL · Feb 15, 2010#131
Originally Posted by Bluevitz-rs ↑
You have to think of it this way...

... with less back-pressure you get more exhaust out of the cylinder on the exhaust stroke, but the intake charge is still the same on a N/A motor. (ok, not EXACTLY the same due to valve overlap and the effect that has on pulling in air, but basically the same.) The intake charge will be "cleaner" than what a stock ECU is programmed for. The stock A/F ratio is based on the back-pressure being there and the amount of residual exhaust gasses still left inside the cylinder on the intake stroke.

A very simple cheat to make the ECU run richer is to trick it into thinking the engine is colder that it really is. If you add a resistor to the Water Temp Sensor and make the ECU think the engine is only running at 110°F or so it'll think it needs more fuel for running in the cold weather. (this might also set a code for the thermostat, but it's nothing major.)

Another method is to add a resistor to the intake temp sensor in the MAF meter. You can trick it into thinking it's sucking in air at -40°. This should have the same effect, but with less chance of setting a code.
This issue is not cat related. Thanks.
CTScottUSA, CT · Feb 15, 2010#132
Are you running the stock drive by wire throttle body, or is it upgraded to a cable throttle? If it's still DBW, going into limp mode is indicative of a failure of one of the two APP (accelerator pedal position) sensor circuits.
Jason@SportsCarThread starterDebary, FL · Feb 15, 2010#133
Originally Posted by CTScott ↑
Are you running the stock drive by wire throttle body, or is it upgraded to a cable throttle? If it's still DBW, going into limp mode is indicative of a failure of one of the two APP (accelerator pedal position) sensor circuits.
Yes, still DBW. And it does seem to be in limp mode.
Jason@SportsCarThread starterDebary, FL · Feb 16, 2010#134
Test day pics:
Picture not included in this copy
Picture not included in this copy
YarisSedanCalifornia - Bay Area · Feb 16, 2010#135
LOL if i didnt know what HP means for SCCA i would look at your car at quick glance and it looks like your advertising your car has 51 horsepower.
markitectMichigan · Feb 16, 2010#136
Guys, he knows what he's doing

If it started when he was almost out of gas then there was probably gunk floating on top of the fuel which has now clogged the fuel filter, fuel pump or an injector(s).

Although with it being only one cylinder I would probably rotate the injectors around and see if the misfire moves, before I pull the fuel pump/filter, but I also have an interior in the way.

Good to see it on the track!!!!!!!!!
Jason@SportsCarThread starterDebary, FL · Feb 16, 2010#137
Just to eliminate it as a possibility, and so we don't have to do it later, we are taking the fuel injectors and pump to RC Engineering this week to have them tested and cleaned. One less thing.
kngrsllSpartanburg, SC · Feb 16, 2010#138
i thought about putting a 89.5 wHP sticker on my rear bumper just to rub a little more salt in the wound :)
Jason@SportsCarThread starterDebary, FL · Feb 16, 2010#139
Originally Posted by kngrsll ↑
i thought about putting a 89.5 wHP sticker on my rear bumper just to rub a little more salt in the wound :)
I started with 5 HP (last digit of the VIN), but someone in the same race group had 5 reserved, so they asked me to change it.

It is all temporary anyway... Once the new graphics are done it will have a number that is significant to Toyota's racing history. 😉
LorenSafety Harbor, FL · Feb 16, 2010#140
Um... did you put new plugs in?

I've put more than a few track miles on my Yaris and the only misfire problem I ever had was due to the factory "100,000 mile" iridium spark plugs.

Replaced them with a set of plain ol' parts store NGK's, problem solved.

I got two different codes from this problem, and at least one "shut down" that happened 2-3 times, but didn't set a code. Apparently, when the ECU detects repeated misfires (such as when I graze the rev limiter in 3rd coming out of turn 17 at Sebring), it just says "NO" and goes into limp mode until you cycle the ignition.

So, if you haven't already, put a new set of plugs in it.
Jason@SportsCarThread starterDebary, FL · Feb 16, 2010#141
Originally Posted by Loren ↑
Um... did you put new plugs in?

I've put more than a few track miles on my Yaris and the only misfire problem I ever had was due to the factory "100,000 mile" iridium spark plugs.

Replaced them with a set of plain ol' parts store NGK's, problem solved.

I got two different codes from this problem, and at least one "shut down" that happened 2-3 times, but didn't set a code. Apparently, when the ECU detects repeated misfires (such as when I graze the rev limiter in 3rd coming out of turn 17 at Sebring), it just says "NO" and goes into limp mode until you cycle the ignition.

So, if you haven't already, put a new set of plugs in it.
We have not yet, but we will be replacing the plugs and coils while we are waiting on the injectors. Better to have it all fresh.
LorenSafety Harbor, FL · Feb 16, 2010#142
If you shotgun everything, you'll never really know what the problem was or which of your spares are actually good parts.

Troubleshooting 101: Change one part at a time.
Jason@SportsCarThread starterDebary, FL · Feb 16, 2010#143
Originally Posted by Loren ↑
If you shotgun everything, you'll never really know what the problem was or which of your spares are actually good parts.

Troubleshooting 101: Change one part at a time.
Spares are not used parts. 😉 At some point it will all be new, so might as well get this stuff out of the way.

Change one part at a time if you want to take a week. Replace it all with good stuff right off the bat, and hopefully you never touch it again.

If I had a spare motor I would just put it in, God knows what was done to this thing when it had FI. But I don't have a spare, so we will just wait till there is a break in the season for a proper build. 😎
cali yarisCanoga Park, CA · Feb 16, 2010#144
such as when I graze the rev limiter in 3rd coming out of turn 17 at Sebring
name dropper 😉
LorenSafety Harbor, FL · Feb 16, 2010#145
Originally Posted by Jason@SportsCar ↑
Spares are not used parts. 😉 At some point it will all be new, so might as well get this stuff out of the way.
I meant the old parts that you're taking off. Are you planning on pitching them? Surely you'll keep them around as spares... and wouldn't it be nice to know whether or not they are good?

But, sure, if you've got more budget than time... rock on!
Jason@SportsCarThread starterDebary, FL · Feb 17, 2010#146
Originally Posted by Loren ↑
I meant the old parts that you're taking off. Are you planning on pitching them? Surely you'll keep them around as spares... and wouldn't it be nice to know whether or not they are good?

But, sure, if you've got more budget than time... rock on!
Most of the time its more time than budget, but we already missed one race, so we will do everything we have to make the next. I am not a fan of keeping old parts as spares - you took them out for a reason. 🤷 Once I know what parts a car uses I always try to keep new ones. For the RX-8 it is coils, plugs and a fuel pump. For the Corvette it was a rear hub and a gas pedal. As long as I had the parts on hand I never needed them at a race. 😆

Looks like we are going to try and get some dyno time before the race, that will be our only chance to beat it up and see if the problem returns.

It will also be good to know if this Camcon unit is tuned safe, or if we should just leave it off. A better ECU setup will come later.
NonStopTuningUSA · Feb 17, 2010#148
Originally Posted by Jason@SportsCar ↑
Test day pics:
Picture not included in this copy
Picture not included in this copy
Great pics sir, keep up the good work!

And please continue to share your updates with us. I certainly do enjoy reading them.

Thanks again!

👍👍
Jason@SportsCarThread starterDebary, FL · Feb 17, 2010#149
It is a very rare day when I don't love my job... But some days it just gets better. Hearing of our small stumble, we have been invited to bring the Yaris to the Toyota tech center for a once over and any help needed to get it in tip top shape for the upcoming race. 🎉

Having access to all of the proper diagnostic tools, and the guys who can fix these cars in their sleep. Priceless.
justjesusOrange County · Feb 17, 2010#150
^ VERY NICE! I wonder if I can make my yaris look like yours before YOU take yours in...