Just talked to our engine builder... They are taking the stock head/intake/TB I sent them and flow testing them to see how well the stock setup works. From that they will make a plan of attack to modify the head (withing the H Prod rules), and we will see what kind of power it makes with the new Jun cams.
Stay tuned
1,311 posts · 595,379 views · page 19 of 27
Replies continued
Picture not included in this copy
🤤
🤤
I'm curious to know if you've looked at the 3.941:1 FD ratio from the Corolla/1st gen Matrix C59 series? Still gives you near-stock, but just a bit more oomph in 1st/2nd. If you're interested in test-fitting it, I'm pretty sure the C59 I bought has one. I can't vouch for its condition as I haven't torn it down that far yet, but I plan on getting to it some time mid-Jan. Oh, and it has a 3.166:1 1st gear too, if that makes any difference.
1st gear is pretty useless for road racing... Beyond pulling the car on the trailer and initiating movement, it is already not used.Originally Posted by CrankyOldMan ↑I'm curious to know if you've looked at the 3.941:1 FD ratio from the Corolla/1st gen Matrix C59 series? Still gives you near-stock, but just a bit more oomph in 1st/2nd. If you're interested in test-fitting it, I'm pretty sure the C59 I bought has one. I can't vouch for its condition as I haven't torn it down that far yet, but I plan on getting to it some time mid-Jan. Oh, and it has a 3.166:1 1st gear too, if that makes any difference.
If 2nd was any shorter the gap to 3rd would only get bigger, if anything I would like a taller 2nd, to reduce the RPM drop to 3rd.
With our 20" tires I will have to turn 7300rpm in 5th to hit 120mph with the stock FD, I am not sure I want to spin a stock bottom end much harder.
Aah, understood. I'm assuming that road racing does a rolling start, like oval tracks?Originally Posted by Jason@SportsCar ↑1st gear is pretty useless for road racing... Beyond pulling the car on the trailer and initiating movement, it is already not used.
If 2nd was any shorter the gap to 3rd would only get bigger, if anything I would like a taller 2nd, to reduce the RPM drop to 3rd.And there's the bugger of it: 1st and 2nd pinions are part of the input shaft. You could in theory get much closer with a C60 gearset, but then you're either notching the frame (illegal for H stock?) or trying to rework a piece of hardened steel (expensive/near-impossible) to shorten the input and output shafts. Any chance you've contacted KAAZ about the option to make a one-off?
Yes, SCCA uses rolling starts for Club Racing. The Pace Car or Pole sitter will set the pace, depending the on the cars in the mix this is typically 50-70mph.Originally Posted by CrankyOldMan ↑Aah, understood. I'm assuming that road racing does a rolling start, like oval tracks?
And there's the bugger of it: 1st and 2nd pinions are part of the input shaft. You could in theory get much closer with a C60 gearset, but then you're either notching the frame (illegal for H stock?) or trying to rework a piece of hardened steel (expensive/near-impossible) to shorten the input and output shafts. Any chance you've contacted KAAZ about the option to make a one-off?
They actually just did a clarification this week which gives FWD Prod cars the same allowances as RWD to trim body/frame bits to fit alternative transmissions. So a swap could be done.
This should get us close enough, even if its not perfect, its way better than what we have had the last two years... At least on paper, we still have to get it on the track. 😉
The trans and all the bits are now in the hands of our mechanic.
I don't want to spoil the surprise, but I think I've cracked the source and specs for these. Could you confirm if I have the specs right?
3rd - 28:19 (1.474:1)
4th - 29:24 (1.208:1)
5th - 25:26 (0.962:1)
3rd - 28:19 (1.474:1)
4th - 29:24 (1.208:1)
5th - 25:26 (0.962:1)
I can not confirm that information... I never counted the teeth, and the parts are all at the shop.Originally Posted by CrankyOldMan ↑I don't want to spoil the surprise, but I think I've cracked the source and specs for these. Could you confirm if I have the specs right?
3rd - 28:19 (1.474:1)
4th - 29:24 (1.208:1)
5th - 25:26 (0.962:1)
I think this may be a bit overkill for our build, but on the upside I think we have zero chance of ever using it up - and I know it wont end up looking like Garm's last clutch. 😈
Looking forward to testing the new OS Giken Super Single race clutch.
Picture not included in this copy
Looking forward to testing the new OS Giken Super Single race clutch.
Picture not included in this copy
How much does the whole assembly weigh in at? Looks light.
On our postage scale the works was 16lbs 13oz. I think that is 1lb more than my aluminum setup from SPEC, but this is a lot smaller in diameter, so the moment of inertia should be very similar.Originally Posted by Bluevitz-rs ↑How much does the whole assembly weigh in at? Looks light.
Just picked up another trailer... 40' open, now we can haul three Yaris at one time.
The cool thing was 19mpg with it empty behind the Tundra, when we towed the enclosed the other day we only got 10.5mpg with it empty.
Picture not included in this copy
The cool thing was 19mpg with it empty behind the Tundra, when we towed the enclosed the other day we only got 10.5mpg with it empty.
Picture not included in this copy
and I know it wont end up looking like Garm's last clutch.It is my wish never to see that again. Your new clutch looks real nice.
Wish I could put it in... Ordered flywheel bolts from TRD on Dec 12th, five show up. On the 21st get an email saying the last one arrived and is shipping to me, should have had it on the 23rd - it never showed and they are closed for the holidays for about ten days.Originally Posted by cali yaris ↑It is my wish never to see that again. Your new clutch looks real nice.
Started calling dealers today, nearest flywheel bolt is in San Fran. So the car will live on jack stands for another few days over a single blot. 😠
What's special about TRD bolts? Aren't they all grade 10 bolts?
Racer pricing from TRD.Originally Posted by Bluevitz-rs ↑What's special about TRD bolts? Aren't they all grade 10 bolts?
WOW, the OS Giken Super Single was a bugger to install... Usually most clutch's have enough play in the splines you can pretty easily stab the transmission and bolt everything up. The OS Giken is so tightly machined you had to have everything lined up dead on. Working by myself it took an hour to get the trans bolted up, normally this is a ten minute job. I was beat.
So far I have only driven it in and out of the driveway, so driving impression is very limited. Pedal effort is high and it grabs hard. Would be great for a FI car, but I am not sure I would use it on a daily driver. Hopefully I will get a better idea of what its really like next week.
So far I have only driven it in and out of the driveway, so driving impression is very limited. Pedal effort is high and it grabs hard. Would be great for a FI car, but I am not sure I would use it on a daily driver. Hopefully I will get a better idea of what its really like next week.
^ with a trailer. 😆
Just weighed the OE assembly (pressure plate, clutch disc and flywheel) 26lbs 8oz - this was used but only 1000miles, you can still see the machine marks in the flywheel, so this should be an accurate weight of a new one.Originally Posted by Jason@SportsCar ↑On our postage scale the works was 16lbs 13oz. I think that is 1lb more than my aluminum setup from SPEC, but this is a lot smaller in diameter, so the moment of inertia should be very similar.
That was a nice little drop.
OS Giken is making a new diff with more plates for the Yaris. 🤷
I don't think we are even using full lock up now. 😲Originally Posted by cali yaris ↑OS Giken is making a new diff with more plates for the Yaris. 🤷
The OS Giken IMO has always been a grabby clutch. Tilton would have been a better choice although it is more spendy. It is very street friendly and has a super light/soft pedal.Originally Posted by Jason@SportsCar ↑WOW, the OS Giken Super Single was a bugger to install... Usually most clutch's have enough play in the splines you can pretty easily stab the transmission and bolt everything up. The OS Giken is so tightly machined you had to have everything lined up dead on. Working by myself it took an hour to get the trans bolted up, normally this is a ten minute job. I was beat.
So far I have only driven it in and out of the driveway, so driving impression is very limited. Pedal effort is high and it grabs hard. Would be great for a FI car, but I am not sure I would use it on a daily driver. Hopefully I will get a better idea of what its really like next week.
Got the new Hoosier radial slick to test out. 🤤
Picture not included in this copy
Picture not included in this copy
Could you through on just the clutch assembly with the bolts, if possible. Curious to see how much that heavy PP is.Originally Posted by Jason@SportsCar ↑Just weighed the OE assembly (pressure plate, clutch disc and flywheel) 26lbs 8oz - this was used but only 1000miles, you can still see the machine marks in the flywheel, so this should be an accurate weight of a new one.
That was a nice little drop.
Just got back from Willow Springs, shaking down the 2012. 😁 Considering how little it done to it when compared to the 99 car, it was fast. Just needs a little more tweaking, but a great first outing.
Picture not included in this copy
Picture not included in this copy
Those tires...so much meat. 🤤
How do you think (so far) the car compares with the one you race?
How do you think (so far) the car compares with the one you race?
The rear fenders on the 2012 don't like me so much anymore, I spent a lot of time with the fender roller making sure those things would fit - we did not want to flare this car.Originally Posted by cali yaris ↑Those tires...so much meat. 🤤
How do you think (so far) the car compares with the one you race?
So far I am impressed. The longer wheelbase makes the car much more stable, and it does not get away as quick when it does break loose. The car exceeded my expectations for the day, it was nearly a full second quicker than I expected it to be... Still not as quick as the 99, but so far we have been unable to get the AEM mated up to the new ECU. Once we get the parts equal on both cars it may have a slight edge due to the lower roof-line and more stable platform. 👍 However, I am doubtful I will get it as light as the 99 (which is down to 1800lbs), the lack of aftermarket body panels is going to make it hard to drop those last few lbs.
I sure do like the looks of it better than the old car.
Picture not included in this copy
Are you having issues with the AEM on the 2012 ECM, or have you just not had a chance to sort out the wiring differences yet?Originally Posted by Jason@SportsCar ↑The rear fenders on the 2012 don't like me so much anymore, I spent a lot of time with the fender roller making sure those things would fit - we did not want to flare this car.
So far I am impressed. The longer wheelbase makes the car much more stable, and it does not get away as quick when it does break loose. The car exceeded my expectations for the day, it was nearly a full second quicker than I expected it to be... Still not as quick as the 99, but so far we have been unable to get the AEM mated up to the new ECU. Once we get the parts equal on both cars it may have a slight edge due to the lower roof-line and more stable platform. 👍 However, I am doubtful I will get it as light as the 99 (which is down to 1800lbs), the lack of aftermarket body panels is going to make it hard to drop those last few lbs.
We have had vendors looking for the plugs, so we could build an PNP like with did on the 99, but no luck. And so far we have not had a chance to try the hardwired method, we will likely start going down this road after the race next weekend. I hate to go hardwired because it is really nice being able to plug in the stock ECU if we had a problem, but we may not have a choice in this case.Originally Posted by CTScott ↑Are you having issues with the AEM on the 2012 ECM, or have you just not had a chance to sort out the wiring differences yet?
I think the new connectors are from Sumitomo. It would probably be easier to get an engine harness and ECM from Toyota to harvest a male and female set from.Originally Posted by Jason@SportsCar ↑We have had vendors looking for the plugs, so we could build an PNP like with did on the 99, but no luck. And so far we have not had a chance to try the hardwired method, we will likely start going down this road after the race next weekend. I hate to go hardwired because it is really nice being able to plug in the stock ECU if we had a problem, but we may not have a choice in this case.
Just got the new head with Jun cams back from Loynings... Oh how I wish I had time to install it and retune the car before this weekends race.
Picture not included in this copy
Picture not included in this copy
I am so jelly
I want to leave work NOW and install this. 😆Originally Posted by ilikerice ↑I am so jelly
So if anyone is wondering, it does not look like the 9.5 Jun cams is a direct bolt-in, some machine work is needed.
Relief cuts for the cam:
Picture not included in this copy
Stock pressure plate with hardware is 9lbs - the bolts made up about 3oz of that.Originally Posted by Bluevitz-rs ↑Could you through on just the clutch assembly with the bolts, if possible. Curious to see how much that heavy PP is.
cutting weight where ever you can.. 👍
is this where you grinded? Is it just this cam lobe or others also?
is this where you grinded? Is it just this cam lobe or others also?
1 attachment not included in this copy
It is the area you circled, and to the left of it, he actually took it all the way down to the bucket area. From what I can tell the head got this treatment on both sides of the bucket, at every cam lobe.Originally Posted by ilikerice ↑cutting weight where ever you can.. 👍
is this where you grinded? Is it just this cam lobe or others also?
oh wow.. I see that now..
Hey another question I got for you.
I was looking at a picture of your cabin in the attached pic below,
I noticed the Sparco seat is pretty low to the floor and the steering wheel is almost at neck level. I am sure your very comfortable with this setup from the video's I have seen at events. Is there a visibility issue looking over the dash? I mean your eye level has to be even with the dash if not just a bit above..
OR, are you just really tall? lol
Hey another question I got for you.
I was looking at a picture of your cabin in the attached pic below,
I noticed the Sparco seat is pretty low to the floor and the steering wheel is almost at neck level. I am sure your very comfortable with this setup from the video's I have seen at events. Is there a visibility issue looking over the dash? I mean your eye level has to be even with the dash if not just a bit above..
OR, are you just really tall? lol
1 attachment not included in this copy
The setup has changes since that pic was done for SEMA 2010... The seat and wheel are both lower and further back now, and I now have a halo seat. 😲 We no longer have to fit a bunch of guest drivers so the seat sliders were removed, anyone who wants to drive the car has to suck it up and sit where I like.Originally Posted by ilikerice ↑oh wow.. I see that now..
Hey another question I got for you.
I was looking at a picture of your cabin in the attached pic below,
I noticed the Sparco seat is pretty low to the floor and the steering wheel is almost at neck level. I am sure your very comfortable with this setup from the video's I have seen at events. Is there a visibility issue looking over the dash? I mean your eye level has to be even with the dash if not just a bit above..
OR, are you just really tall? lol
The seat is 1" lower and back about an 1". The stock steering column was removed and a custom unit that moved the wheel down and back is in there, although the wheel is still in basically the same location in relation to where I sit.
Is there a visibility issue? Depends on your point of view. 😆 Many of the open cars I have to race against can not be seen if we are bumper to bumper, other than the roll hoop and the drivers helmet. But it is certainly not an issue. At speed you are looking so far down track whats immediately in front of you is not really an issue.
I am 5'9", I think my head just clears the top of the seat. You can see from this shot, where the camera is just below eye level, it is not bad at all: http://www.youtube.com/watch?v=gm4NJaZ3CHo
Interesting.. thanks. I was curious. I am 5'10/11 depending who I stand next to. I was skeptical about buying a carbon fiber seat like the one you have in the picture. Looking over the dash was my issue being that I autocross. I will look at that video when I get home.. work doesnt permit youtube
In an autocross car I sit much closer to the wheel and up higher, you need to see the cones. 😉Originally Posted by ilikerice ↑Interesting.. thanks. I was curious. I am 5'10/11 depending who I stand next to. I was skeptical about buying a carbon fiber seat like the one you have in the picture. Looking over the dash was my issue being that I autocross. I will look at that video when I get home.. work doesnt permit youtube
I am 5'10/11 depending who I stand next to.I like how that is a relative thing. 😆
thanks for discussing this guys. I used a few washers to lower my steering wheel a bit. Any more and my left knee would hit it.
I'm 5'11" myself and have alway mounted my seats as low as possible for road racing, it does make it difficult to auto-x, but you learn to adapt. Here are a few pics of the way I mounted the seat in my Celica, using brackets I made myself.Originally Posted by ilikerice ↑Interesting.. thanks. I was curious. I am 5'10/11 depending who I stand next to. I was skeptical about buying a carbon fiber seat like the one you have in the picture. Looking over the dash was my issue being that I autocross. I will look at that video when I get home.. work doesnt permit youtube
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Oh and as you can see, I still have the front portion of the cage to add, installed just the rollbar for my own peace of mind for HPDE events.
racerb
Already received my SSK I bought off you Jason - thanks so much! Didn't even know it was possible to ship that fast..
That is a good idea.. you talking about those bolts circled in the diagram? did you have to get longer bolts, or was there enough to thread left?Originally Posted by cali yaris ↑I like how that is a relative thing. 😆
thanks for discussing this guys. I used a few washers to lower my steering wheel a bit. Any more and my left knee would hit it.
1 attachment not included in this copy
I did the same thing with mine before I went to a custom setup, as I recall there was enough thread there to drop it a 1/2".Originally Posted by ilikerice ↑That is a good idea.. you talking about those bolts circled in the diagram? did you have to get longer bolts, or was there enough to thread left?
if you dont mind me asking, what needed to be done to that to make it custom fit for you?Originally Posted by Jason@SportsCar ↑I did the same thing with mine before I went to a custom setup, as I recall there was enough thread there to drop it a 1/2".
Also, is it custom in the fact that it was fabricated or parts were exchanged with other oem parts from other makes/models?
again if I am stepping out of the bounds on your secrets I totally understand
Not sure of Jason's set-up, but I'm using a straight section of what is called double D steering shaft, cut to proper length with the quick release center section welded on. In my case the original column both tilted and telescoped, so I'm going back to the last flex joint before it turns down toward the firewall base. Where the original large centering bearing also held the telescoping handle, I've come out about 2" and added a 3/4" male hiem joint which hold the steering shaft and lines it up more with my seating possition in the car. When I installed my seat, I moved it to the right as far as the center tunnel would allow, making the steering wheel slightly too far to the left.Originally Posted by ilikerice ↑if you dont mind me asking, what needed to be done to that to make it custom fit for you?
Also, is it custom in the fact that it was fabricated or parts were exchanged with other oem parts from other makes/models?
again if I am stepping out of the bounds on your secrets I totally understand
racerb
interesting..
I dont mean to hijack your thread Jason.
I think I understand what your saying racerb, but could you PM me a picture of that setup. I am curious. Also that moving the seat further to the shifter is a good idea too. It would make shifting a bit more comfortable
I dont mean to hijack your thread Jason.
I think I understand what your saying racerb, but could you PM me a picture of that setup. I am curious. Also that moving the seat further to the shifter is a good idea too. It would make shifting a bit more comfortable
Sorry for continueing the hijack, but couldn't find any pictures of my steering column set-up. So here is a very simular set-up to mine on an MG, same basic deal hung verticle where mine hangs horizontal.Originally Posted by ilikerice ↑interesting..
I dont mean to hijack your thread Jason.
I think I understand what your saying racerb, but could you PM me a picture of that setup. I am curious. Also that moving the seat further to the shifter is a good idea too. It would make shifting a bit more comfortable
http://www.google.com/imgres?imgurl=...9QEwAw&dur=180
racerb 🤷
Similar to mine as well. Splined shaft with a quick release welded on. Simple, much lighter than stock, and further reduced the steering effort.Originally Posted by racerb ↑Sorry for continueing the hijack, but couldn't find any pictures of my steering column set-up. So here is a very simular set-up to mine on an MG, same basic deal hung verticle where mine hangs horizontal.
http://www.google.com/imgres?imgurl=...9QEwAw&dur=180
racerb 🤷