certainly does not need to. i removed my rear axle over 5 years ago and never used a torque wrench to re-install it. "tight" worked just fine.Originally Posted by Kaotic Lazagna ↑Dang, my crappy torque wrench doesn't go that high =(
Rear suspension
257 posts · 100,812 views · page 2 of 6
Replies continued
So whats the end end of this?
Raise the bolt location then X happens?
Idk if people think a stable rear is better for handling?
I'd assume that having a happier rear end, or a rear end with a TOE OUT setting is better for turning? That would also make the rear end feel like its gonna get in front of you, right? Ahh, Loren, help me out.
Raise the bolt location then X happens?
Idk if people think a stable rear is better for handling?
I'd assume that having a happier rear end, or a rear end with a TOE OUT setting is better for turning? That would also make the rear end feel like its gonna get in front of you, right? Ahh, Loren, help me out.
I would assume then this is for the Japanese following of the car for when it's lowered and being raced? Seems easy enough for me... Drill an extra hole for people who want to race it and leave one for the stock height...
Too bad it took us forever to find it =(
Too bad it took us forever to find it =(
I didn't mean to come off as the feeling of being ignored, I was meaning that I did read all of the previous posts and pages, I just didn't fully get it what the end result is supposed to be like and what the pros/cons would be to moving it. My apologies
The final word on this discussion will have to wait until someone does some before and after alignment checking.
My speculation is that it simply improves the toe curve on a lowered Yaris, letting the rear suspension work more like it would at stock height. It's not gonna give you "toe out", just "less toe in".
Now... here's a question for those who have done it. (I'm freakin' lazy, could be months before I get around to it) Is there enough slop in those pivot bolts that the alignment of the rear axle becomes an issue? Can you end up "dog-tracking" due to the rear axle assembly not pointing straight along the centerline of the car? Or are they tight enough that it's not a concern? (probably another question that it will take an alignment rack to answer accurately)
My speculation is that it simply improves the toe curve on a lowered Yaris, letting the rear suspension work more like it would at stock height. It's not gonna give you "toe out", just "less toe in".
Now... here's a question for those who have done it. (I'm freakin' lazy, could be months before I get around to it) Is there enough slop in those pivot bolts that the alignment of the rear axle becomes an issue? Can you end up "dog-tracking" due to the rear axle assembly not pointing straight along the centerline of the car? Or are they tight enough that it's not a concern? (probably another question that it will take an alignment rack to answer accurately)
I should take my car to one of those "free alignment checks" like firestone and wheel works. And see how it looks afterwards.
Let us know what they say. I just did this last weekend and I'm curious too.Originally Posted by YarisSedan ↑I should take my car to one of those "free alignment checks" like firestone and wheel works. And see how it looks afterwards.
I just lowered my yaris a little while ago and I still havent gotten around to adressing the toe and camber alignments yet. I was gunna just shim the rears but I think this in combo with the shims might be a better solution.
here's my basic explanation on what this mod would change(see pictures attached)
I think that on a stock height car, this mod isnt needed.
here's my basic explanation on what this mod would change(see pictures attached)
I think that on a stock height car, this mod isnt needed.
2 attachments not included in this copy
So if i go back to my technical schooling days it looks like that mod changes the caster. But caster dosnt really make much difference unless it is on the steering tires.
The way the rear axle assembly is designed, it also changes toe. (caster is irrelevant, as the rear wheels don't steer)
At stock height, the car has a certain amount of toe-in. As the axle rotates up (when the suspension compresses... or when the car is lowered) on its pivot point, the angle goes more inward.
If you lower the car and DON'T move the pivot point, you have more static toe-out than stock, which isn't good for turning. (great for going straight)
Moving to the higher pivot point on a lowered car should bring the toe back closer to factory spec.
At stock height, the car has a certain amount of toe-in. As the axle rotates up (when the suspension compresses... or when the car is lowered) on its pivot point, the angle goes more inward.
If you lower the car and DON'T move the pivot point, you have more static toe-out than stock, which isn't good for turning. (great for going straight)
Moving to the higher pivot point on a lowered car should bring the toe back closer to factory spec.
Ahhhhh i 100 percent got you now. Explains why every reponse is only feeling a difference on turns. So pretty much a cheap and easy way to correct the toe without involving use of shims on lowered vehicles. I am curiouse why toyota did not mention to do this with the instructions that come with the TRD springs it seems like a no brainer.Originally Posted by Loren ↑The way the rear axle assembly is designed, it also changes toe. (caster is irrelevant, as the rear wheels don't steer)
At stock height, the car has a certain amount of toe-in. As the axle rotates up (when the suspension compresses... or when the car is lowered) on its pivot point, the angle goes more inward.
If you lower the car and DON'T move the pivot point, you have more static toe-out than stock, which isn't good for turning. (great for going straight)
Moving to the higher pivot point on a lowered car should bring the toe back closer to factory spec.
my uber simple drawing don't really show the effect on the toe and camber very well but this mod does effect both.As the caster angle changes toe turns into camber and vise-versa. If there were absolutlely no stock Toe or Camber than it wouldnt matter, but that isnt the case.
Awesome discovery. I have had mad rubbing issues on the rear since installing the PG rear hub spacers because of how much toe in there is. Hopefully doing this mod will compensate enough to clear a lot of it up.
I did mine on a rack today and it was a real PAIN in the ass to get the back side of the bushing lined up. Ended up having to disconect the shocks so i could get the torsion beam to move a bit to get it to finally lined up. Took me with a flashlight and another guy with a pry bar prying on the end of the bushing to get the bolt hole to line up.
After test drive i notice you have this feeling like the car is more leveled or like the rear end is sitting lower now. Also going over bumps i started to hear this clank clank sound. Turns out the torsion bar sits higher up now i guess because of the angle. So its banging against my megan tie bar. I am going to see if i can get a file and file it down. If not looks like i may have to remove it. So for those who have that rear little bar by the gas tank that seems like it has no use at all make sure you remove it first before you do this mod.
After test drive i notice you have this feeling like the car is more leveled or like the rear end is sitting lower now. Also going over bumps i started to hear this clank clank sound. Turns out the torsion bar sits higher up now i guess because of the angle. So its banging against my megan tie bar. I am going to see if i can get a file and file it down. If not looks like i may have to remove it. So for those who have that rear little bar by the gas tank that seems like it has no use at all make sure you remove it first before you do this mod.
There is very minimal space in there I doubt you would make your car dog-track. The metal on the inside of the bushings where the bolt goes throught is fairly tight in the slot. I would have put this on the alignment rack up at work but our rear heads don't calibrate so I wouldn't be able to tell youOriginally Posted by Loren ↑
Now... here's a question for those who have done it. (I'm freakin' lazy, could be months before I get around to it) Is there enough slop in those pivot bolts that the alignment of the rear axle becomes an issue? Can you end up "dog-tracking" due to the rear axle assembly not pointing straight along the centerline of the car? Or are they tight enough that it's not a concern? (probably another question that it will take an alignment rack to answer accurately)
Sounds like the alignment heads at my old shop. Good old "set the toe and let it go" Tell your owner to get a laser system. No more comping heads again.Originally Posted by lilredrocket ↑There is very minimal space in there I doubt you would make your car dog-track. The metal on the inside of the bushings where the bolt goes throught is fairly tight in the slot. I would have put this on the alignment rack up at work but our rear heads don't calibrate so I wouldn't be able to tell you
Hmm i can almost swear the rear of my car sits lower now. The fender gap is the same but the rear of the car is lower. Its as if the car has 15s in the front and 17 inch rims in the back. And then i swapped out the 15s back in the back. Before and after. It looks like i lowered the car about a inch more looking strait on from the back. I dont think its some placebo effect either looking strait on it does look lower. But looking from the side from the wheel and fender it looks the same. If someone is planning on doing this mod please take a tape measure and measure from fender to ground and rear bumper to ground before and after please.
from these that you write, the axle going down but the height is the same.
maybe that is...
maybe that is...
that doesnt seem unreasonable... the spring sits slightly fore of the center of the wheel. if you change the pitch of the beam, you can raise or lower the spring perch as well. personally, i would think it would make it sit a little higher as the perch is tilted slightly higher.Originally Posted by YarisSedan ↑Hmm i can almost swear the rear of my car sits lower now. The fender gap is the same but the rear of the car is lower. Its as if the car has 15s in the front and 17 inch rims in the back. And then i swapped out the 15s back in the back. Before and after. It looks like i lowered the car about a inch more looking strait on from the back. I dont think its some placebo effect either looking strait on it does look lower. But looking from the side from the wheel and fender it looks the same. If someone is planning on doing this mod please take a tape measure and measure from fender to ground and rear bumper to ground before and after please.
oh, we need a sticky on this topic btw
Now that I look back at it as Loren stated it should help lessen the amount of toe out. My only concern is with that part of the axle postioned up higher wouldn't it make the wheel go back towards the rear of the car more when it is flexing. My problem is my tire is rubbing in this area.
Picture not included in this copy
Picture not included in this copy
pic of my rear wheel after spacer install.
Picture not included in this copy
Picture not included in this copy
Maybe the suspension expert himself can shed some light on this :) I just don't want to spend 2 hours doing this just for it to make my rear rub worse.
Last night, I was installing my new wheels, took the car for a test ride and when I got back I looked at it from behind very carefully. I might be wrong, but I swear I can tell the toe-in on the rear wheels. If you look carefully, along the tire walls, trying to align one edge with the opposite edge, looking along the vehicle, in a horizontal line, right above the center hub, you will see that the imaginary line hits the body somewhere in the front, it doesn't stay parallel to the centerline. And I noticed that with the axle mounted on the higher bolt. Imagine how much more toe-in you get on the lower bolt, since turning the axle forwards would probably increase the toe-in angle even more...
Yeah I am starting to think this mod may be the exact opposite of what I need to do for my rubbing issue 🤷
Yeah looking at my tire after this mod. Instead of it being centered between both sides of the fender its leaning more towards the back fender. So if thast the area you are rubbing against it will make your situation worse.
You can easily measure toe with a tape measure. If you think there's so much that you can SEE it with the naked eye, you should certainly be able to measure it with a tape measure.Originally Posted by fmicle ↑I might be wrong, but I swear I can tell the toe-in on the rear wheels.
Pick a groove on the tire, measure from side to side at the front of the tire, as high up as you can get without interference. Measure the same grooves at the back of the tire. Difference = toe. Narrower in front = toe-in.
This won't give you exact numbers, as you can't get measurements at exactly the vertical center of the wheel, and you're potentially dealing with some tread flex, etc. But, it's close enough to get an idea of what's going on.
I agree, and what I'm trying to say is that it would be MUCH WORSE (as in more toe-in) if you DID NOT do this mod for a lowered car...
I am just trying to confirm the theory on this thread with my empirical observations.
I am just trying to confirm the theory on this thread with my empirical observations.
Yes, this might not be the solution to the rubbing issue, but it is the right solution for keeping the toe-in closer to factory spec after lowering.Originally Posted by PHXDEMON ↑Yeah I am starting to think this mod may be the exact opposite of what I need to do for my rubbing issue 🤷
Picture not included in this copy
Whenever i go over bumps now my rear axle slams against this tie bar. I tried to sand down the horrible welds so it is pretty much smooth and even then there is still banging. Sadly i either have to take it off or put the axle back to the factory position =(
Whenever i go over bumps now my rear axle slams against this tie bar. I tried to sand down the horrible welds so it is pretty much smooth and even then there is still banging. Sadly i either have to take it off or put the axle back to the factory position =(
So is it the general consensus that this is a good mod to do if your vehicle is lowered? That's what I'm getting but want to be sure. From that drawn diagram on one of the pages, it looks like with a lowered vehicle that by putting it up on the top bolt hole, it's putting things near back the stock suspension position. If that's the case, why would that be more beneficial than leaving it in the bottom hole and having the rear toe changed?
I thought you couldn't change the rear toe on the Yaris...
Aren't these springs installed upside down?Originally Posted by YarisSedan ↑Picture not included in this copy
http://shop.microimageonline.com/pro...7&categoryId=4Originally Posted by fmicle ↑I thought you couldn't change the rear toe on the Yaris...
And I don't think it really matters if springs are upsidedown or not.
Are they? Yeah i dont think its possible really to install them upside down since they will function the same way still. But that could explain why i get some creaking noise occasionally while others do not with the same springs.Originally Posted by fmicle ↑Aren't these springs installed upside down?
Aren't those stock shocks? that would be one of the reasons why your car would be hitting that brace imo 🤷Originally Posted by YarisSedan ↑Picture not included in this copy
Whenever i go over bumps now my rear axle slams against this tie bar. I tried to sand down the horrible welds so it is pretty much smooth and even then there is still banging. Sadly i either have to take it off or put the axle back to the factory position =(
Yeah changing to tokiko shocks is on my list of things to do.
So I woke up this morning and I guess almost instinctual, I set out to the garage and grabbed the tools to do the job. I'd definately have to say that having two people is much easier (it always is usually anyways when it comes to cars) but it's not too bad if your going solo. The hardest part, like someone else mentioned, was the rear bushing. It was a pain in the rump to try and line it up just right so you could start threading the bolt through all the way.
I took it for a quick test drive after I was finished and for me speaking, I can think of a few choice words to sum up my initial impressions. Refined, smooth and reactive.
It reminds me alot of the stock suspension ride, how it's calm and smooth feeling. All of that feeling now with the lowered suspension components. It certainly feels more "planted" in the rear with even less boat motion feeling. The turning feedback definately increased has well. I jerked the steering wheel side to side to see what it would do, and it reacted quick and precise. Much better than when the rear axle beam was in the lower position.
One thing I noticed though is that the rear certainly doesn't appear to be lower or any of that. If anything, it almost looks like it's a slight pinch higher. Could be just a mind trick since the axle beam is tucked up underneath a bit more and it allows to see more space under the car. Also, I don't really see any difference in the tire being more "towards the rear". Looks the same gap to me towards front or rear of the fender. Another thing I'd be a little concerned with is taking the time to adjust to how it drives now. The steering and reaction during my quick test drive is much nicer feeling and quicker, better handling...but along with that, I believe you could get yourself into some trouble if it's wet or slick out. I'm concerned about a more likely possibility of snap oversteer if you jerked or steered too suddenly.
It's a given though that anytime someone changes a part on a car that alters it's powertrain or suspension, that the person takes it easy so they can learn what is different and how it reacts. Too many countless stories of some kid that throws a turbo on a Civic and goes out that night to get it on. Ends up crashing the car because it's completely different than what it used to be and the driver had no idea how to react. Essentially, the car is NOT the same car as what you used to drive. Be safe out there.
I took it for a quick test drive after I was finished and for me speaking, I can think of a few choice words to sum up my initial impressions. Refined, smooth and reactive.
It reminds me alot of the stock suspension ride, how it's calm and smooth feeling. All of that feeling now with the lowered suspension components. It certainly feels more "planted" in the rear with even less boat motion feeling. The turning feedback definately increased has well. I jerked the steering wheel side to side to see what it would do, and it reacted quick and precise. Much better than when the rear axle beam was in the lower position.
One thing I noticed though is that the rear certainly doesn't appear to be lower or any of that. If anything, it almost looks like it's a slight pinch higher. Could be just a mind trick since the axle beam is tucked up underneath a bit more and it allows to see more space under the car. Also, I don't really see any difference in the tire being more "towards the rear". Looks the same gap to me towards front or rear of the fender. Another thing I'd be a little concerned with is taking the time to adjust to how it drives now. The steering and reaction during my quick test drive is much nicer feeling and quicker, better handling...but along with that, I believe you could get yourself into some trouble if it's wet or slick out. I'm concerned about a more likely possibility of snap oversteer if you jerked or steered too suddenly.
It's a given though that anytime someone changes a part on a car that alters it's powertrain or suspension, that the person takes it easy so they can learn what is different and how it reacts. Too many countless stories of some kid that throws a turbo on a Civic and goes out that night to get it on. Ends up crashing the car because it's completely different than what it used to be and the driver had no idea how to react. Essentially, the car is NOT the same car as what you used to drive. Be safe out there.
Yeah i have simular conserns as you. I went to take a really quick turn after i did this mod to see how it would react. And if you ever watched initial D when the character makes that face when his car does something unexpected that same thing happend to me. It scared me for a second cause it was completely unexpected. Going to have to slowly get used to it. Its as if you have to turn to wheel less while going into a sharp turn. If you jerk the wheel too hard you will have to turn it back the other way to correct it otherwise you will drive into whatever you are cornering around if thta makes sense.Originally Posted by detroiter ↑So I woke up this morning and I guess almost instinctual, I set out to the garage and grabbed the tools to do the job. I'd definately have to say that having two people is much easier (it always is usually anyways when it comes to cars) but it's not too bad if your going solo. The hardest part, like someone else mentioned, was the rear bushing. It was a pain in the rump to try and line it up just right so you could start threading the bolt through all the way.
I took it for a quick test drive after I was finished and for me speaking, I can think of a few choice words to sum up my initial impressions. Refined, smooth and reactive.
It reminds me alot of the stock suspension ride, how it's calm and smooth feeling. All of that feeling now with the lowered suspension components. It certainly feels more "planted" in the rear with even less boat motion feeling. The turning feedback definately increased has well. I jerked the steering wheel side to side to see what it would do, and it reacted quick and precise. Much better than when the rear axle beam was in the lower position.
One thing I noticed though is that the rear certainly doesn't appear to be lower or any of that. If anything, it almost looks like it's a slight pinch higher. Could be just a mind trick since the axle beam is tucked up underneath a bit more and it allows to see more space under the car. Also, I don't really see any difference in the tire being more "towards the rear". Looks the same gap to me towards front or rear of the fender. Another thing I'd be a little concerned with is taking the time to adjust to how it drives now. The steering and reaction during my quick test drive is much nicer feeling and quicker, better handling...but along with that, I believe you could get yourself into some trouble if it's wet or slick out. I'm concerned about a more likely possibility of snap oversteer if you jerked or steered too suddenly.
It's a given though that anytime someone changes a part on a car that alters it's powertrain or suspension, that the person takes it easy so they can learn what is different and how it reacts. Too many countless stories of some kid that throws a turbo on a Civic and goes out that night to get it on. Ends up crashing the car because it's completely different than what it used to be and the driver had no idea how to react. Essentially, the car is NOT the same car as what you used to drive. Be safe out there.
All i know is my car just got really a lot lot more fun ot drive 😁
yay for oversteer!!!!! at least it's not understeer
Well, I'm not an expert, but yours are upside down from the ones in this DIY (pictures 6 and 7 are relevant): TANABE DF210 Spring Install [pics]Originally Posted by YarisSedan ↑Are they? Yeah i dont think its possible really to install them upside down since they will function the same way still. But that could explain why i get some creaking noise occasionally while others do not with the same springs.
So, either both ways are fine, or one of you has them upside down 😉
The reason I brought it up is because I have similar looking springs, where the lower coils are closer together than the higher ones and I installed mine according to the DIY above. Also, the ends are not exactly the same, since one end gets a rubber cap and the other end sits in a groove on a plate on the axle. One end brings the coil almost to a circle, while the other kind of ends open. So at least from a geometry perspective, it's not the same. But it might be just fine... I don't know... that's what I'm trying to figure out 🙂
I installed mine based on the instruction manual that came in the box from toyota. But now you got me wondering if i installed them right or not lol.Originally Posted by fmicle ↑Well, I'm not an expert, but yours are upside down from the ones in this DIY (pictures 6 and 7 are relevant): TANABE DF210 Spring Install [pics]
So, either both ways are fine, or one of you has them upside down 😉
The reason I brought it up is because I have similar looking springs, where the lower coils are closer together than the higher ones and I installed mine according to the DIY above. Also, the ends are not exactly the same, since one end gets a rubber cap and the other end sits in a groove on a plate on the axle. One end brings the coil almost to a circle, while the other kind of ends open. So at least from a geometry perspective, it's not the same. But it might be just fine... I don't know... that's what I'm trying to figure out 🙂
Picture not included in this copy
going by this picture for tannabe it looks like the tightly coiled are supose to be on top since thats how the label is printed on the coil.
is good or bad to do this ? what is the positive and negative advantage of this mod?
It is good, IF you're lowered. As explained above, the rear axle has some built-in camber and toe which will be off if you lower your car. I got mine to an alignment shop last night and the rear axle was right within factory specs - no adjustment needed. I'm pretty sure the alignment would have been off if I hand't done it after changing the springs.Originally Posted by AL441 ↑is good or bad to do this ? what is the positive and negative advantage of this mod?
The only disadvantage someone mentioned about this mod is that you might get some rubbing because if the modified geometry. Look above on this thread for a picture. I don't have that problem on my hatchback with a mild drop (1.4") But if you don't do it, you would either have to adjust the alignment with some spacers or you will get uneven tire wear.
I'm glad I could help 😆Originally Posted by YarisSedan ↑But now you got me wondering if i installed them right or not lol.
what is the advantages of this mods? what is the positive advantages?
Scroll up 3 posts! 🍻Originally Posted by AL441 ↑what is the advantages of this mods? what is the positive advantages?
Anybody had a chance to see what sort of changes the pivot change makes, compared to not changing the pivot?
^ it's a free mod, just the kind you like. TRY IT. (You'll like it)
Yeah! I shifted up the pivot point of my rear arm. The very first impression given me is, WoW!! My ride feel so much more balance especially on the rear suspension during hard cornering.
In the past after i drop my ride with Tanabe NF springs, i do gain the look of it but somehow i lose a little on the "corner handling" & "cornering balance" if i corner really hard. The reason is due to the "super soft" spring rate of the NF spring gave & i bear in mind that NF springs is strictly meant for "Comfort" usage. I am already used to it and live with it of the "soft" & "floating" cornering of the NF springs!!
Till yesterday i change the rear of my suspension pivot point, while i'm testing it, i smile to myself!!!!!! 😁😁😁 Feeling "unbalance" & "floating" in the hard cornering will be a thing of the PAST!!!🤘
Thank you, Yaris World & all mates to share in this forum!!🤘
As i'm not sure how the rear camber or toe angle change after shifting to the upper pivot point. Below are the points i figure it out after the mod, i really can see the rear wheel being "extend" to the rear end. Meaning having a longer wheel-base after the change. Below are the points i thought which really make sense to have the longer wheel-base after the change.
1. Once our ride is lowered, our rear arm will move/angle "upward" where this will "shorten" our wheel-base a little depending on how much u lowered.
More lowered = Shorter wheel base
2. In order to enjoy back the near stock/longer wheel base, where this addtional hole is there for. Upon shifting the pivot point higher, the arm will now have the most "level" & "parallel" to the ground, for this we'll gain back the stock/longer wheel base.
Please do not frame me if the above pointers are wrong or does not make sense to any of you. Pls correct me if i'm wrong. As i'm still learning and want to share with you guys with my logic. 👍
In the past after i drop my ride with Tanabe NF springs, i do gain the look of it but somehow i lose a little on the "corner handling" & "cornering balance" if i corner really hard. The reason is due to the "super soft" spring rate of the NF spring gave & i bear in mind that NF springs is strictly meant for "Comfort" usage. I am already used to it and live with it of the "soft" & "floating" cornering of the NF springs!!
Till yesterday i change the rear of my suspension pivot point, while i'm testing it, i smile to myself!!!!!! 😁😁😁 Feeling "unbalance" & "floating" in the hard cornering will be a thing of the PAST!!!🤘
Thank you, Yaris World & all mates to share in this forum!!🤘
As i'm not sure how the rear camber or toe angle change after shifting to the upper pivot point. Below are the points i figure it out after the mod, i really can see the rear wheel being "extend" to the rear end. Meaning having a longer wheel-base after the change. Below are the points i thought which really make sense to have the longer wheel-base after the change.
1. Once our ride is lowered, our rear arm will move/angle "upward" where this will "shorten" our wheel-base a little depending on how much u lowered.
More lowered = Shorter wheel base
2. In order to enjoy back the near stock/longer wheel base, where this addtional hole is there for. Upon shifting the pivot point higher, the arm will now have the most "level" & "parallel" to the ground, for this we'll gain back the stock/longer wheel base.
Please do not frame me if the above pointers are wrong or does not make sense to any of you. Pls correct me if i'm wrong. As i'm still learning and want to share with you guys with my logic. 👍