Yarisworld Archive

Rear suspension

257 posts · 100,812 views · page 3 of 6

Replies continued

detroiterMetro Detroit · Nov 29, 2009#101
For those who have done the mod, even though it's much more stable feeling now while turning and cornering, would you agree that it seems the rear end ride comfort is a bit more uncomfortable/harder feeling?
evo165*tIny dOts iN AsiA* · Nov 29, 2009#102
Originally Posted by detroiter ↑
For those who have done the mod, even though it's much more stable feeling now while turning and cornering, would you agree that it seems the rear end ride comfort is a bit more uncomfortable/harder feeling?
Yes sir, i do agree with you on this point!! Before the change, in fact my ride are way "too" comfortable to do any street or hard cornering for my liking. After this mod, my ride comfort doesn't affect much to it. In fact, my gf mentioned it feel more comfortable because she felt her body roll lesser than before. (Same gf, same corner speed, same location, same dry weather)

It is all depending on what ur liking & habit to drive your Yaris. 😉

More comfortable ride = Less stable ride OR
Less comfortable ride = More stable ride
YarisSedanCalifornia - Bay Area · Nov 29, 2009#103
Originally Posted by detroiter ↑
For those who have done the mod, even though it's much more stable feeling now while turning and cornering, would you agree that it seems the rear end ride comfort is a bit more uncomfortable/harder feeling?
I think it puts more force on the springs i could be wrong. When i put my springs back in place it took a heck of a lot more effort than before. I think they are being compressed slightly more somehow thus allowing a slighter higher spring rate?
detroiterMetro Detroit · Nov 29, 2009#104
^^

That's exactly what I was thinking. It basically preloads the spring at a higher rate, giving it the harsher feel and better reaction.

Why did you have a hard time putting the springs back in, just curious? Mine never fell out or needed to be moved/adjusted
YarisSedanCalifornia - Bay Area · Nov 29, 2009#105
Originally Posted by detroiter ↑
^^

That's exactly what I was thinking. It basically preloads the spring at a higher rate, giving it the harsher feel and better reaction.

Why did you have a hard time putting the springs back in, just curious? Mine never fell out or needed to be moved/adjusted
Well i did mine on a lift and was fighting to put the bushing back in. I needed to remove the shock to give me more play when i did that the spring fell out and one thing led to another lol. Finally got it in and when i went to put the spring back it was much more difficult and had to use a tranny jack under the beam where the shock bolts up to get everyhing back together. What i should have done is used 2 tranny jacks one on each side before i unbolted everythign to support it all. Same as if soemone was doing it on the ground using 2 additional floor jacks. Would have probally went much more smooth.

But i think it does preload the spring more. I can feel more harshness at higher speeds especially. But man its so worth it. Makes me really wana get some new shocks now. Should have taken advantage of the 10 percent off deal.
kngrsllSpartanburg, SC · Nov 29, 2009#106
so i did this yesterday. i think the car sits SLIGHTLY lower but that may be an illusion.

as for the ride, the car is more comfortable! that is really the thing i noticed the most! I didnt notice a huge change in handling, but i also just installed an LSD which i only drove on for one day, which made a huge change in handling. over bumps on the interstate, the car is not nearly as jolting, it was quite pleasant driving it home! which is very unusual, after about an hour in the car, the body starts to feel quite fatigued.

as i said already, i didnt notice a huge handling difference, but that is probably due to getting to used to the LSD (which is very different than the car was before.)

another thing, i think an alignment using the SPC shims is a good idea after this mod. i think there is enough slack there to create some subtle alignment changes. once the bolts are torqued down, they beam is in place. then i would correct it with the shims.

great find!
fmicleSan Jose, CA, USA · Nov 29, 2009#107
I don't see how this can preload the springs at a higher rate, since it's the weight of the car that's loading the springs, which is the same. The only thing that changes is the angle of the axle plate versus top plate, which hold the springs in place. With the axle down those plates are almost parallel, with the axle up the plates are at a certain angle.
fmicleSan Jose, CA, USA · Nov 29, 2009#108
Originally Posted by evo165 ↑
(Same gf, same corner speed, same location, same dry weather)
🤣
franticAustralia · Nov 29, 2009#109
im on coilovers... you reckon this mod will do any good??
fmicleSan Jose, CA, USA · Nov 29, 2009#110
I guess that depends on your setting. If you're lower than stock by 1 inch or more in the back, I'd say yes.

Disclaimer: don't take auto mechanical advice from software engineers 😉
kngrsllSpartanburg, SC · Nov 29, 2009#111
Originally Posted by frantic ↑
im on coilovers... you reckon this mod will do any good??
yeah, that doesnt matter.
YarisSedanCalifornia - Bay Area · Nov 30, 2009#112
Hmm new issue now. Over really really hard bumps or potholes the rear beam smacks against the gas tank and put some scrapes in it already. Kinda scared over time if it may wear a hole through the plastic. Looks like its time to swap out to some performance shocks.
LorenSafety Harbor, FL · Nov 30, 2009#113
The beam axle is contacting the fuel tank? Photos?
YarisSedanCalifornia - Bay Area · Dec 1, 2009#114
Originally Posted by Loren ↑
The beam axle is contacting the fuel tank? Photos?
Ill try to take some tomorrow if i have time. It only happens if i go over say a speed bump really fast. You can hear a slight clunk and today i was doing a brake flush i figured id take a look at everything to see if something looked loose and that when i noticed scratching on the side of the gas tank. Nothing major but over time it might put some wear. So now i drive lot slower pulling out of driveways and going over bumps or holes =(. With the car on a drive on rack there really is little clearance between the beam and the gas tank. That little bar i showed in a pic before cant really be removed with a load on the car. Had to put it on a conventional lift to take the load off the beam so it would drop enough down. So even with the bar removed there is still some slight contact but with the tank now. Before it would make contact with the tie bar even going slowly out of a driveway. Any twisting seemed to make it contact on the drivers side of the beam. Now where its contacting is slightly on the drivers side still but none on the passanger side. I cant imagine what would happen if i had passangers in the rear now lol.
ddongbaphay · Dec 1, 2009#115
I got an alignment done, and i have the alignment numbers on a stock bolted rear end, dropped on Megans.

.. but its in the car.
ddongbaphay · Dec 1, 2009#116
Okay, here are my alignment specs. I'll include my fronts anyways, even though its technically not related. This alignment was after I installed the adjustable camber bolts from Garm.

Front before: camber / toe
Left -3.13 // 7/8
Right -2.64 // 9/16

After: camber // toe
L -1.96 // 0
R -1.92 // 0

Rear:
L -.76 // 1/4
R -1.23 // 1/8

I have rear shims I'm gonna add before my next track day.
kngrsllSpartanburg, SC · Dec 1, 2009#117
what were the before and after rear settings with the beam change?
ddongbaphay · Dec 1, 2009#118
Originally Posted by kngrsll ↑
what were the before and after rear settings with the beam change?
I didn't do the beam change yet. If the beam change would add toe in, I don't think I'll end up doing it. I just wanted to put out there, what my alignment was with an agressive drop. The bottom of my chassis is scratched up from speed bumps and such. Thats how low I am.
kngrsllSpartanburg, SC · Dec 1, 2009#119
it should reduce toe in and improve bumps in the rear so you may want to consider it. the lower you are, the more it should help since the geometry is further from stock than normal.
ddongbaphay · Dec 1, 2009#120
Improve bumps how?

I have some rear shims I'm going to add later on.
ozmddDFW, TX · Dec 1, 2009#121
I'm getting the alignment checked this week to see the before/after results of the rear axle relocation, and I felt that the rear was more "planted" at the last autocross I did.

That being said, I also discovered/confirmed that there is some "clunking" in bigger dips, from contact between things that shouldn't be doing so, so I'm probably going to put it back to stock. I'll take picks when its up in the air to zero-in on the offending parts. I'll also post the alignment numbers just so everyone can get an exact idea of what the mod does.
It definitely does reduce the toe-in that results from lowering, which is nice. Maybe I can run the alternate setting when I get the coilovers installed and am able to have more control over the suspension settings.
detroiterMetro Detroit · Dec 1, 2009#122
I 3rd the happening of clunking on hard bumps or dips. I don't know what it is that's hitting but I'll be straight forwards when saying whatever it is, it sure doesn't sound too healthy.
kngrsllSpartanburg, SC · Dec 2, 2009#123
i havent noticed it, but i dont run slammed, and i have a 6kg rear spring
enobmort42Denver, CO · Dec 2, 2009#124
Hmm. I'm lowering my car now, and I may be wrong, but from what I've gathered after reading this thread, I either need an alignment or I should adjust the pivot point?
YarisSedanCalifornia - Bay Area · Dec 2, 2009#125
Originally Posted by detroiter ↑
I 3rd the happening of clunking on hard bumps or dips. I don't know what it is that's hitting but I'll be straight forwards when saying whatever it is, it sure doesn't sound too healthy.
I felt the same way till i looked at it in the air and its the gas tank!

But i like how the car handles so much now i dont want to put it back the way it was. I am glad im not the only one who hears occasional clunking. I am hoping some stiff shocks may correct this issue. If not may have to get stronger springs.
LorenSafety Harbor, FL · Dec 2, 2009#126
Originally Posted by enobmort42 ↑
Hmm. I'm lowering my car now, and I may be wrong, but from what I've gathered after reading this thread, I either need an alignment or I should adjust the pivot point?
Both.

After lowering, you need to align the FRONT of the car, it's the end that has factory adjustments.

In the rear, the only thing that changes with lowering is the toe-in, and there's no way to adjust it without shimming. This new "modification" should minimize or possibly eliminate the toe change, but be aware that it's a very new idea and the potential downsides (contact between axle and fuel tank?) are just being discovered.
LorenSafety Harbor, FL · Dec 2, 2009#127
Whoever does this next, if you have time, do this:

You should be removing the springs to accomplish this task, anyway. So, before you reinstall the springs, after you put the bolts into the higher pivot point position, raise the rear wheels/hubs to max height and see exactly where and just how bad the contact is. Take pictures of where it is making contact, and of how close the upper and lower spring perches are to each other. (how much would the spring be compressed if it were there?)

The problem could potentially be dealt with by lengthening the bump stop. Of course, that's going to mean that very low cars will be resting on the bump stops and essentially have no suspension travel... which defeats the purpose of damn near any suspension mod. (assuming the goal of a suspension mod is to make the car handle better in real world conditions)

Could potentially also be dealt with by just trimming some material on the axle assembly somewhere, or maybe relocating or modifying something that is bolted TO the axle. Need to take a close look and see exactly what's going on.
ddongbaphay · Dec 2, 2009#128
I kinda get the feeling that people with regular drop springs aren't supposed to do this.
enobmort42Denver, CO · Dec 2, 2009#129
Originally Posted by ddongbap ↑
I kinda get the feeling that people with regular drop springs aren't supposed to do this.

I hope that's the case! I just have some TRD springs on my stock shocks, until I have enough for the TRD ones... The instructions don't say anything about the pivot point...
fmicleSan Jose, CA, USA · Dec 2, 2009#130
I've been running with this mod for almost 2 weeks now and haven't had any issues so far. I've only had the baby in the back, no other loads or longer trips and the roads are decent where I drive, so no big bumps or anything. I haven't heard any bumping, other than just the springs a couple of times after I installed them, probably from just setting in...

I am running on Progress springs though, with a medium drop of 1.4". I'll keep an eye on it though, but I've seen the alignment numbers on the rear axle with this mod and they look perfect, I would probably do my best to keep it that way.

Oh and the handling (with the new Toyo T1R's that I got) is amazing 🤤
ddongbaphay · Dec 2, 2009#131
I think the T1Rs are doing the grunt work of the handling.

On a side note, I installed the 23mm rear sway bar. IDK what I'm supposed to be feeling though.
detroiterMetro Detroit · Dec 2, 2009#132
I just got an alignment check and everything came back well within factory specs while using the higher bolt point. ill throw the numbers up soon...
kngrsllSpartanburg, SC · Dec 2, 2009#133
Originally Posted by ddongbap ↑
I kinda get the feeling that people with regular drop springs aren't supposed to do this.
why do you feel that? to me, that seems like the ideal candidate.
ddongbaphay · Dec 2, 2009#134
Cause Toyota sells TRD shocks and springs w/o saying anything about the second set of holes.
fmicleSan Jose, CA, USA · Dec 2, 2009#135
Originally Posted by ddongbap ↑
IDK what I'm supposed to be feeling though.
Less body roll (swinging from side to side) when cornering, changing lanes, etc. The car should feel more "planted" on the road and you should be able to take turns at higher speeds than before.

Disclaimer: please drive responsibly! 🙂
fmicleSan Jose, CA, USA · Dec 2, 2009#136
Originally Posted by ddongbap ↑
Cause Toyota sells TRD shocks and springs w/o saying anything about the second set of holes.
Toyota also says you can put 14" and 15" wheels on your car and no mention of bigger sizes and as far as I know there was a photo posted here with someone having 19" wheels on the Yaris. Plenty of people have 17"s and I had 16"s until 2 weeks ago 😉
YarisSedanCalifornia - Bay Area · Dec 2, 2009#137
Hmm i put my car on rack tonight and took a bunch of pictures. Ill post everything tonight if i have time when i get home. The rear springs look partially compressed. Half the coils are compressed and touching. You couldnt even fit ap iece of paper between half of them. I think this could be why the rear end feels lower and appears to be lower. It actually is. Also why the rear feels stiffer because this should increase the spring rate since its under a big preload now. . The rear beam is only maybe 2-3 inches away from the gas tank. I think the clunk is either the beam making contact with the filler neck or the top of the tank or the springs just bottoming out and hitting the bump stop. I think it could be a combination of any of them.

So i think if you did this mod on factory springs you would have some gain. Would even out the rear end so it dosnt sit abnormally high and get all the benifit still without the issue some of us who lowered the car have. Ill post the pics tonight so you guys can see what i mean. Hopefully loren can take a look at them and give us his thoughts.
YarisSedanCalifornia - Bay Area · Dec 2, 2009#138
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
YarisSedanCalifornia - Bay Area · Dec 2, 2009#139
So first picture the area i circled is the area i am concerned about. But now that i think about it when i removed the bar i had to struggled so its a possibility it may have caused some of the scratching on the gas tank. My plan is to put some chalk on that area tomorrow and then drive it over some bumps and see if it rubs it off.

Second picture you can see the small distance between the beam and the gas tank. When i had my tie bar installed there it was literally less than inch from beam which is why it kept clanking against it.

The second picture with the circle mark shows how close the beam is to the filler neck of the gas tank. I suppose if you had a bunch of heavy set people in the back seat and went over a really hard pothole there is a chance it could make contact. Also the fewer last pictures you can see how tightly wound the coil spring is. I am not sure if this is suppose to be normal. But the top portion of the springs are all touching. I am thinking the clunk is the spring completely compressing and making contact with the bottom but not 100 percent sure.

Still hoping loren will take a look at this pics and give us some insight.
LorenSafety Harbor, FL · Dec 2, 2009#140
Remove the springs. Then you can easily move the axle through its complete range of motion to check for interference with the fuel tank or anything else.

The pix are good, they tell us the area of concern... but they don't show any actual contact.
cali yarisCanoga Park, CA · Dec 2, 2009#141
If there were contact, you'd see it - the paint would be worn/chipped/rubbed.
ddongbaphay · Dec 2, 2009#142
Originally Posted by fmicle ↑
Less body roll (swinging from side to side) when cornering, changing lanes, etc. The car should feel more "planted" on the road and you should be able to take turns at higher speeds than before.

Disclaimer: please drive responsibly! 🙂
I'm already on coilovers, so most of the bodyroll reductions went down after the coils.
fmicleSan Jose, CA, USA · Dec 2, 2009#143
I think it's normal for the coils to look the way they do, same thing with mine, even though different brand, the first 3 or so spirals touch each other...
yaris 2szgreece · Dec 3, 2009#144
yarissedan, did you cut the bump stops when installed the springs?
if you did it, maybe it's from this.

by the way, i asked the tte.de about bump stops cutting and told me that i don't have to do this. i have the tte springs
lilredrocketDFW, Texas · Dec 4, 2009#145
I have not been on for a couple of days but every once in a while I have heard a noise from the rear after dips. I have a little bit different exhaust sets up than everyone else and I believe that the axle is very close to the exhaust. I noticed this when moving my axle up to the higher position I will take pics later this week
YarisSedanCalifornia - Bay Area · Dec 4, 2009#146
Originally Posted by yaris 2sz ↑
yarissedan, did you cut the bump stops when installed the springs?
if you did it, maybe it's from this.

by the way, i asked the tte.de about bump stops cutting and told me that i don't have to do this. i have the tte springs
No havent touched the bump stops. I dont think theres bump stops really to cut in the rear its a different type of setup than in the front. Its spring and shock combo.
AND189australia · Dec 4, 2009#147
hmmm
AND189australia · Dec 4, 2009#148
DIY anyone ???


First jack her up i put the mounts as far away as posable so i have lots of room to play
Picture not included in this copy

pull the wheels off
Picture not included in this copy

position jack so it is under swing arm and to get the bolt out you need to slightly tap the mount up to take the cross load off the bolt Picture not included in this copy

this is the bolt you will be taking out only one of mine seamed to have lock tight so when putting them back i used locknut on both with some grease
Picture not included in this copy

so once the bolts are taken from both sides you can back prop one first and this is the fiddly part, if you have only one jack ... to get the holes to line up you need to keep the axel at the same hight as both sides if you don't you will fined it easy for one side and real hard for the other, so if you can use two people with two are you can just prop one side as high as you can the go back to the other and so on until the holes match up
Picture not included in this copy

as i was alone i had to back prop it took a little longer when moving the axel up i used the cares weight to move the axel with a jack (so i am not lifting the car) (loren)for the sake of others that putting a jack under the center of the beam axle is a bad idea. It can be bent in that manner.

Picture not included in this copy
Picture not included in this copy

You can see the thread is shaved for the first 5mm witch means if you are having problems getting the bolt in you can give it a little tap with a hammer
Picture not included in this copy

After putting it all back i took if for a test run down bluegum road and it was crazy it just cuts into corners at speed and i did not see a drop or lift in hight, But i did fine the rear a little more bouncy, other mods i have done are the trd springs and struts, sway bar, strut brace, tires and wheels and this has been the cheapest and i enjoyed it to good luck !!!

some other pics of my old mans car and mine
Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
LorenSafety Harbor, FL · Dec 4, 2009#149
AND129, I think you know this by the fact that you mentioned being careful not to lift the car at this point, but it's worth mentioning for the sake of others that putting a jack under the center of the beam axle is a bad idea. It can be bent in that manner.

Neat that you were able to do this without pulling the shock bolts and removing the springs. Probably a toss-up as to which way is actually easier. (only two bolts to drop the shocks and it should make the whole process of fitting those pivot bolts a lot easier)
AND189australia · Dec 4, 2009#150
ok thanks as i did say the car was not lifted by the axel only its own weight and i didnt have to many problems i will note it thanks mate