Maitre_Te_TeOriginal postQuébec · Nov 12, 2009#1Sorry for my english.
I have an yaris 1.5L
I don't know why but check your reat suspension. The rear suspension assembly can be jack 2 inchs at the pivot.
Do you know why?
Picture not included in this copy
Picture not included in this copy
Replies 256
LorenSafety Harbor, FL · Nov 12, 2009#2Oh, I like that one!
I'd have to go out and look at the car and really think about it... but do you suppose that it's a factory designed option to improve the geometry of the rear suspension for a lowered "sport" version?
Interesting.
cali yarisCanoga Park, CA · Nov 12, 2009#3definitely, I'll be under my car looking at that too - never noticed before, I wonder.
Maitre_Te_TeThread starterQuébec · Nov 13, 2009#4With the original car, the rear suspension have for example 35 degree. If you drop your car, the rear angle is not the same, it's maybe 20 degree. If you jack your pivot 2 about inch, you can not have the exactly 35 degree beacause you know you can drop 2 inch, 1.5 inch, 1 inch, But you can have 30 degree. So, If your drop is 1 ich, I think that this mod is not important.
I look under the car et I think that the gaz tank and other thing is not a problem.
Tell me about your impression!
Maitre_Te_TeThread starterQuébec · Nov 13, 2009#5 Originally Posted by
Loren ↑ Oh, I like that one!
I'd have to go out and look at the car and really think about it... but do you suppose that it's a factory designed option to improve the geometry of the rear suspension for a lowered "sport" version?
Interesting.
Don't forget, in japan, you have a race series with a yaris (vits and vios) and maybe toyota have do this mod option for the race series!
lilredrocketDFW, Texas · Nov 13, 2009#6Ok so it was really slow at work today and I thought I would move my axle to this new discovered position. Right now I am running DF210's and a TRD rear sway bar I also am only running on stock wheels, tires, and shocks. After I moved my axle I took a quick test drive and......... OMG it is freaking amazing!!!!!!!!!!!!!!!! The car feels completely different better turn in and feels like it has less body roll than before!!!! I took me about 30 mins to an hour to move my axle (I think this was easier to do with my car on a lift then just jacking it up although it could be done that way) I say if you want to expirement I say do it because it is easy to return to stock if need be!!! Hope this helps you out!!! if you have any questions let me know
1NZYaris1New Zealand · Nov 13, 2009#7 Originally Posted by
lilredrocket ↑ Ok so it was really slow at work today and I thought I would move my axle to this new discovered position. Right now I am running DF210's and a TRD rear sway bar I also am only running on stock wheels, tires, and shocks. After I moved my axle I took a quick test drive and......... OMG it is freaking amazing!!!!!!!!!!!!!!!! The car feels completely different better turn in and feels like it has less body roll than before!!!! I took me about 30 mins to an hour to move my axle (I think this was easier to do with my car on a lift then just jacking it up although it could be done that way) I say if you want to expirement I say do it because it is easy to return to stock if need be!!! Hope this helps you out!!! if you have any questions let me know
I dont suppose you could put better photo's up 🤷
advocatelocation · Nov 13, 2009#8Interesting find for sure. Anybody else going to give it a try?
lilredrocketDFW, Texas · Nov 13, 2009#9 Originally Posted by
1NZYaris1 ↑ I dont suppose you could put better photo's up 🤷
I will take my camera to work tomorrow and show you where this is and how it looks. OOOHHHHHH and just ot let you know it actually does not lower the car any. I thought it was going to because the holes are like 2-3" apart but I still have the same ride hight!!!
Maitre_Te_TeThread starterQuébec · Nov 14, 2009#10I don't know what, but I think that you will say "tank you" for this mod !!! :P
I will do this mod the next week.
Picture please with this mod :P !!!
1NZYaris1New Zealand · Nov 14, 2009#11 Originally Posted by
lilredrocket ↑ I will take my camera to work tomorrow and show you where this is and how it looks. OOOHHHHHH and just ot let you know it actually does not lower the car any. I thought it was going to because the holes are like 2-3" apart but I still have the same ride hight!!!
Your my Hero 👍 , peterpoop loves you 😆 bad joke sorry .🤣
CosmonautSanentoneyow, Tecksis · Nov 14, 2009#12i am very curious about this now.
WolfWingsKansas City, MO, USA · Nov 14, 2009#13I'm not running lowered, but I'm tempted to try this and see how things change. May be one of those 'harsher/noisier ride' changed that has no downsides for handling even for non-lowered perhaps?
2006frontySan Bernardino · Nov 14, 2009#14Isn't this just changing the instant center? Or is anti-squat what it changes???
🤷
supmetSouthern California · Nov 14, 2009#15 Originally Posted by
lilredrocket ↑ I will take my camera to work tomorrow and show you where this is and how it looks.
interested and waiting for more pictures :D
lilredrocketDFW, Texas · Nov 14, 2009#16My bad guys I FAILED!!! I forgot to grab my camera on the way out the door this morning so I will snap a few good pics tomorrow before I wash my car.
lilredrocketDFW, Texas · Nov 14, 2009#17 Originally Posted by
Maitre_Te_Te ↑ I don't know what, but I think that you will say "tank you" for this mod !!! :P
I will do this mod the next week.
Picture please with this mod :P !!!
THANK YOU FOR BRINGING THIS TO OUR ATTENTION!!!!!!
Maitre_Te_TeThread starterQuébec · Nov 14, 2009#18No problem guys.
LorenSafety Harbor, FL · Nov 15, 2009#19Damn, I'm gonna have to give this a try.
It shouldn't affect ride height at all, btw. Ride height is set with the spring height between the spring perches and this won't change that. It just changes the "static" angle of the beam axle assembly, presumably to a more favorable angle for a lowered car.
Basically, it should make whatever effects are designed into the movement of the beam axle (anti-squat, dynamic toe, etc) that are optimized to work at stock ride height... be more optimal for a car that's lowered. It's got to be a good thing.
Kaotic LazagnaCentral Valley, CA · Nov 15, 2009#20How easy would it be to move it to the said point?
kngrsllSpartanburg, SC · Nov 15, 2009#21wow... crazy! good find.
LorenSafety Harbor, FL · Nov 15, 2009#22I'd guess that it would require removing the bottom shock bolts to decompress the spring. Then just removing the two pivot bolts, moving the axle assembly down, putting the pivot bolts back in, and putting the shock bolts back in.
Should be as easy as pie. (Mmmmmm... pie!)
lilredrocketDFW, Texas · Nov 15, 2009#23 Originally Posted by
Loren ↑ I'd guess that it would require removing the bottom shock bolts to decompress the spring. Then just removing the two pivot bolts, moving the axle assembly down, putting the pivot bolts back in, and putting the shock bolts back in.
Should be as easy as pie. (Mmmmmm... pie!)
Actually you are moving the front of the rear axle up. I did this on a car lift with lift stands and air tools took about 30 mins to an hour. Probably about 2 hours laying on the ground.
This mod completely changed the way my car rotates. I would have to say this is great for people that track or auto-x their cars.
lilredrocketDFW, Texas · Nov 15, 2009#24Here are the pics that I snapped. You can see where the bolt was before by how clean it was under it. Don't say anything about the dirty car I washed it right after I took these. Sorry they are so big I didn't resize because I wanted to make sure you could see what I was talking about.
5 attachments not included in this copy
Maitre_Te_TeThread starterQuébec · Nov 15, 2009#25 Originally Posted by
Loren ↑ It just changes the "static" angle of the beam axle assembly, presumably to a more favorable angle for a lowered car.
Exactly. I will do this this mod this week. Seriously, i'm very happy to talk to you about this mod and it work just... great!!! I wish to test it the next summer at lapping day! Just one thing. Before torque you axle beam bolt at your pivot, just swing your car 2 to 3 time juste for set your bushing. After, torque the bolt, car not jacked. If not, your bushing work hard!
This is the toyota procedure ;)
LorenSafety Harbor, FL · Nov 15, 2009#26Yes, that makes sense. Torquing the pivot bolts with the suspension drooped will cause the bushings to be preloaded when you set the car down.
lilredrocketDFW, Texas · Nov 15, 2009#27Good point I will have to take my bolts loose again and retorque them...
rningonfumesSoCal · Nov 20, 2009#28Bump!
gsf1200mBoston · Nov 20, 2009#29I thought more people would be trying this! Hopefully I will be doing this tomorrow afternoon to my xD.
lilredrocket, any tips for this or is it as simple as it seems?
ozmddDFW, TX · Nov 20, 2009#30I did it. Super easy. I put the car on jack stands at the rear jack points, used floor jacks to support the weight of the axle and keep the springs from fighting me, and removed the rear wheels, both for weight reduction and access.
You need a 17mm socket with either a breaker bar or an impact wrench to loosen it. It has loctite from the factory, so I'd have some handy for the re-install.
The swap is really easy, but a small prybar or big screwdriver will aid in lining-up the holes, which is the hardest part of the process. Take your time and wiggle the arm around till you can get a thread started, then you're home free. I forgot the exact torque spec, but you want it on there really good, 90-100 ft/lbs, maybe? (I'll check that # tonight and edit this post.)
That's it. Took me 30 minutes total, working alone.
bigbangbeTHESDA · Nov 20, 2009#31wow good one Maitre_Te_Te
just step out check yes its on the sedan
ozmddDFW, TX · Nov 20, 2009#32Clarification, please: Are you saying it is better to torque the bolts while the suspension is unloaded, or after the car is on the ground in order to preload the bushings?
gsf1200mBoston · Nov 20, 2009#33ozmdd, have you taken it out yet? How does it feel?
ozmddDFW, TX · Nov 20, 2009#34Yes, but havent' been able to push it hard yet. It definitely feels better - more planted - on the turn-in. Not sure if it altered the effective spring rate or preload on the spring, although it seems like it would a little.
LorenSafety Harbor, FL · Nov 20, 2009#35You want to torque either on the ground or with the suspension otherwise supporting the weight of the car. (on ramps, suspension on a jack or jackstand, etc) If you torque with the suspension drooped, when you put the weight on the car, there will be a twisting load on the bushings which can cause the rear of the car to sit artificially high and/or damage the bushings over time.
LorenSafety Harbor, FL · Nov 20, 2009#36I'm gonna bet the primary effect in play here is the "toe curve" of the rear suspension. It's designed to be slightly toed in at the factory ride height, and as the suspension compresses in a turn, it toes in a little more for stability. This effect is all built into the rear axle assembly and the angles at which it rotates. So, by changing to the upper holes on a lowered car, you're effectively putting things back into the alignment they were designed for.
To verify this, someone should carefully measure their rear toe before and after making this change. If I'm right, you should see less static toe out after than before.
detroiterMetro Detroit · Nov 22, 2009#37Thanks for the finding! I'm curious though, what exactly is the benefit/gain of doing this procedure? I'm not quite sure I completely get what the end result is. Also, any negatives to it?
kngrsllSpartanburg, SC · Nov 22, 2009#38 Originally Posted by
Loren ↑ I'm gonna bet the primary effect in play here is the "toe curve" of the rear suspension. It's designed to be slightly toed in at the factory ride height, and as the suspension compresses in a turn, it toes in a little more for stability. This effect is all built into the rear axle assembly and the angles at which it rotates. So, by changing to the upper holes on a lowered car, you're effectively putting things back into the alignment they were designed for.
To verify this, someone should carefully measure their rear toe before and after making this change. If I'm right, you should see less static toe out after than before.
hmm,i need an alignment, perhaps i will try this...
YarisSedanCalifornia - Bay Area · Nov 22, 2009#39 Originally Posted by
Loren ↑ I'm gonna bet the primary effect in play here is the "toe curve" of the rear suspension. It's designed to be slightly toed in at the factory ride height, and as the suspension compresses in a turn, it toes in a little more for stability. This effect is all built into the rear axle assembly and the angles at which it rotates. So, by changing to the upper holes on a lowered car, you're effectively putting things back into the alignment they were designed for.
To verify this, someone should carefully measure their rear toe before and after making this change. If I'm right, you should see less static toe out after than before.
Hmmm i just had a alignment done few weeks ago. When i get a chance ill do this and get a second alignment done and see the difference and post results for you guys Ill also take a few pics more pics if no one has done it by then to make a little more detailed DIY for those who dont know exactly what we are talking about yet. GOOD FIND!
detroiterMetro Detroit · Nov 23, 2009#40Thanks for the finding! I'm curious though, what exactly is the benefit/gain of doing this procedure? I'm not quite sure I completely get what the end result is. Also, any negatives to it?
cali yarisCanoga Park, CA · Nov 23, 2009#41 I did it. Super easy. I put the car on jack stands at the rear jack points, used floor jacks to support the weight of the axle and keep the springs from fighting me, and removed the rear wheels, both for weight reduction and access.
Exactly how I did it also. Alignment next week, will compare to the last one I did.
IndianspringsazAZ · Nov 23, 2009#42Getting ready to put some DF springs on. Should I move them to the upper hole during the install? Where do you guys trust to do the alignments? I hate going to shops and have to explain to them how to do their job.
YarisSedanCalifornia - Bay Area · Nov 23, 2009#43 Originally Posted by
cali yaris ↑ Exactly how I did it also. Alignment next week, will compare to the last one I did.
Did you hand torque it down or just hit it with a breaker bar as hard as you could? I am guessing it should be torqued to about 145ft lbs. And maybe some threadlocker for some extra insurance. I am going to do this at home on my driveway hopefully tonight. Usually i hit everything down with a impact gun but by hand i like to get torque specs to be on the safe side.
TamagoOff Grid · Nov 23, 2009#44that's some serious torque there ...
LorenSafety Harbor, FL · Nov 23, 2009#45Those pivot bolts don't need to be super-tight. The factory manual is available online, though... look it up!
detroiterMetro Detroit · Nov 23, 2009#46Is there some reason my question has been skipped over twice so far? Just curious.
mojoyarisVancouver · Nov 23, 2009#47If you read above Lorens Posts
"I'm gonna bet the primary effect in play here is the "toe curve" of the rear suspension. It's designed to be slightly toed in at the factory ride height, and as the suspension compresses in a turn, it toes in a little more for stability. This effect is all built into the rear axle assembly and the angles at which it rotates. So, by changing to the upper holes on a lowered car, you're effectively putting things back into the alignment they were designed for."
And on the previous pages you'll get an idea of how it adjusts the suspension geometry
When you lower the suspension in the front you can get bump steer. There are devices to install in the front to adjust and compensate for this. This is something akin to that but in the rear suspension where you level out the torsion beam and realign the toe.
I guess an illustration would be the best way to describe this.
LorenSafety Harbor, FL · Nov 24, 2009#48 Originally Posted by
detroiter ↑ Is there some reason my question has been skipped over twice so far? Just curious.
Um, yeah. I may not have addressed you by name, but your question has been answered. Read.
YarisSedanCalifornia - Bay Area · Nov 24, 2009#49 Originally Posted by
Loren ↑ Those pivot bolts don't need to be super-tight. The factory manual is available online, though... look it up!
I took your advice and looked it up. For those who are interested the factory spec is exactly 67 ft lbs.
Kaotic LazagnaCentral Valley, CA · Nov 24, 2009#50Dang, my crappy torque wrench doesn't go that high =(