Wow,this is probably the coolest idea I have seen done in years for any car.....you sir are a Saint......finally a tach for the car....yes.
GI: "YarGauge" replacement clock module (Digital Tach, etc.)
737 posts · 304,493 views · page 4 of 15
Replies continued
CTScott is tha MAN!!! Can't wait. Thanks again for doing this.
we all owe Scott a big THANKS!
This looks awesome I really want one! Great Job CTScott!!!
I'm impressed! 👏
I want it! 🙂
I want it! 🙂
Here's another teaser - Mounted in my 09 with the orange LCD:
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
2 attachments not included in this copy
How does the unit install to the car Scott? Does it read from the OBD2 port?
Once the full production units are complete, I'll post the install pictures, but basically: You unplug the clock's connector, pop the clock module out, and pop the YarGauge in, in its place. I realized tonight that only 3 tap splices will be necessary, as I can have the clock's power connector plug right into the YarGauge. The three taps are for CAN communication (two taps on the right cluster connector) and one to the AC amplifier for the outside temperature (which is easily accessible by the gas pedal). It uses the same switch lever as the clock as well.Originally Posted by advocate ↑How does the unit install to the car Scott? Does it read from the OBD2 port?
It communicates with the ECM via the CAN bus, but it grabs it at the cluster, so you can still have a scangauge or other device use the OBD port.
just too cool for words
And what about clusters with the clock on the other side? Will compatibility be similar?
I like that it will be able to maintain the stock, orange color. 👍
I do have one question ...
I noticed that in the last pics, the cluster brightnees is turned up to what seems to be to max but the modual seems a bit dimmer than the other displays.
If you were to turn the brightness down a bit like at night, will the new modual still be as visible as the rest of the cluster?
Will the new modual indeed be able to be dimmed along with the cluster?
I do have one question ...
I noticed that in the last pics, the cluster brightnees is turned up to what seems to be to max but the modual seems a bit dimmer than the other displays.
If you were to turn the brightness down a bit like at night, will the new modual still be as visible as the rest of the cluster?
Will the new modual indeed be able to be dimmed along with the cluster?
Originally Posted by RedRide ↑I like that it will be able to maintain the stock, orange color. 👍
I do have one question ...
I noticed that in the last pics, the cluster brightnees is turned up to what seems to be to max but the modual seems a bit dimmer than the other displays.
If you were to turn the brightness down a bit like at night, will the new modual still be as visible as the rest of the cluster?
Will the new modual indeed be able to be dimmed along with the cluster?
Right now I am not using the dimmer feed, so the display would be the same brightness with headlights on or off. Now that it is in the car, that's one thing I'll experiment with to determine if dimming is needed (I have a feeling it won't, as the backlit LCD is not as bright as the speedometer).
I'm still trying to figure that out. The ones with the clock on the right, are either LBs with the cluster with the tach, or are sedans. In both of those cases the odometer and fuel gauge are part of that display, so I can't really replace it. For those, I am trying to figure out another mounting place that would still have the OEM integrated look.Originally Posted by advocate ↑And what about clusters with the clock on the other side? Will compatibility be similar?
Is there still going to be a sedan version?
This brings up another concern.Originally Posted by CTScott ↑Right now I am not using the dimmer feed, so the display would be the same brightness with headlights on or off. Now that it is in the car, that's one thing I'll experiment with to determine if dimming is needed (I have a feeling it won't, as the backlit LCD is not as bright as the speedometer).
Since it is "not as bright......
Often in bright, anbient light, the stock gage cluster is hard to read. Is this also a prblem with the new modual?
Perhaps abient light does not effect it as much?
Is there an easy way to conect it to the dimmer feed?
Question: Can the temperature display read in celsius as well as farenheit?
Yes. A switch bank on the back allows configuration of options including metric vs. US standard.Originally Posted by devinlamothe ↑Question: Can the temperature display read in celsius as well as farenheit?
A possibility would be to sell two versions then?Originally Posted by CTScott ↑I'm still trying to figure that out. The ones with the clock on the right, are either LBs with the cluster with the tach, or are sedans. In both of those cases the odometer and fuel gauge are part of that display, so I can't really replace it. For those, I am trying to figure out another mounting place that would still have the OEM integrated look.
1) Integrated as a clock in a small unit
2) Integrated via a single DIM unit like a scanguage?
Just an idea! Keep up the great work Scott.
Wow, i can't wait to get this! applause to you CTScott for a brilliant idea and execution!
unit looks nice....i can't wait till it comes out. would we use the current push button on the cluster to change between functions?
I am interested in how you'd incorporate it into the sedan! I'll buy.
Yes. It will use the same push button to change modes and set the clock. Programming for the one button user interface has been one of the most difficult aspects of this, but I wanted to avoid making people drill holes for extra switches.Originally Posted by arunto ↑unit looks nice....i can't wait till it comes out. would we use the current push button on the cluster to change between functions?
Sweet. Sorry if this was already answered way back.Originally Posted by CTScott ↑Yes. A switch bank on the back allows configuration of options including metric vs. US standard.
Hmmm. Shift light function would be easy to add. The only thing is that it might not be the ideal place for one peripheral vision wise, while launching.Originally Posted by cdydjded ↑Just found this post, count me in on one. I do have a question, would it be possible to add a programable shift light feature? For example, if I was wanting to shift @ 6200RPM the display would flash when the programed RPM is reached? BTW what you are doing is a great idea, keep up the good work.
Hi all,
New to the forum here.
CTScott - this one cool project you are undertaking. It is great enough to make me join the forum! Count me in for one of these. Thanks for your great work.
New to the forum here.
CTScott - this one cool project you are undertaking. It is great enough to make me join the forum! Count me in for one of these. Thanks for your great work.
Looking good CTScott!
With these tap splices, will it be easy to put back the old unit, in case I
would sell the car? 🤷
With these tap splices, will it be easy to put back the old unit, in case I
would sell the car? 🤷
Yes. You'd pop them off and put a small piece of tape over the nick in the insulation.Originally Posted by Revsson ↑Looking good CTScott!
With these tap splices, will it be easy to put back the old unit, in case I
would sell the car? 🤷
Why remove it if you sell it?Originally Posted by Revsson ↑Looking good CTScott!
With these tap splices, will it be easy to put back the old unit, in case I
would sell the car? 🤷
I suspect that any new owner would like the mod also. 🙂
... and it probably wouldn't work on other cars unless you plan on getting another Yaris if you sold your current one.
After reading this thread it appears the YarGauge will not work on my 2010 3-dr manual, which has a tach on the left.
That's correct, since the clock is not a separate module, like on the tachless ones. I am trying to figure out where the YarGauge could be integrated to have the OEM look for tach equipped liftbacks and sedans.Originally Posted by DenverDave ↑After reading this thread it appears the YarGauge will not work on my 2010 3-dr manual, which has a tach on the left.
Oh that sucks. I was totally going to buy one but didn't know the new ones came with a tach lol.
For 2010 all manual transmission LBs come with the tach. Autos still do not.Originally Posted by goku87 ↑Oh that sucks. I was totally going to buy one but didn't know the new ones came with a tach lol.
Still want me to take some pics of the inside of my cluster? I have one with a tach - just tell me what you need a pic of and I can do it tonight.
I actually have one on my test bench. I don't see being able to mount it within the tach cluster without modification, so I am looking for someplace outside of the cluster. For example, one thought is to mount it in place of one of the center AC vents. I am open to suggestions.Originally Posted by devinlamothe ↑Still want me to take some pics of the inside of my cluster? I have one with a tach - just tell me what you need a pic of and I can do it tonight.
I obviously could mount it in a small enclosure, that you can put anywhere (like the scangauge), but that diminishes its value versus products like scangauge.
Alright then. I am going to look tonight to see where would be a good place to mount it (for me anyway).Originally Posted by CTScott ↑I actually have one on my test bench. I don't see being able to mount it within the tach cluster without modification, so I am looking for someplace outside of the cluster. For example, one thought is to mount it in place of one of the center AC vents. I am open to suggestions.
I obviously could mount it in a small enclosure, that you can put anywhere (like the scangauge), but that diminishes its value versus products like scangauge.
One question though: since we can't replace the clock module, is hooking it up going to be more difficult? IE: are more spliced required?
You'd have 3-4 more wires to tap:Originally Posted by devinlamothe ↑Alright then. I am going to look tonight to see where would be a good place to mount it (for me anyway).
One question though: since we can't replace the clock module, is hooking it up going to be more difficult? IE: are more spliced required?
Ground, constant power, switched power, and possibly dimmer.
To install the proto on my 09 w/out tach, I only had to tap one wire (outside temp sensor), as I realized that the two can bus connections could be made to two test points on the back of the cluster.
Does the '09 5-door LB have a built in temp. sensor? When I installed my CIPA rear-view mirror w/ compass, temp. and map lights, I had to install a temp. sensor. I clipped that to the bottom-most grill on the front bumper.
Yes. All Yaris with AC have it. No aftermarket device would interface to it though, as it isn't universal enough.Originally Posted by IsLNdbOi ↑Does the '09 5-door LB have a built in temp. sensor? When I installed my CIPA rear-view mirror w/ compass, temp. and map lights, I had to install a temp. sensor. I clipped that to the bottom-most grill on the front bumper.
I was thinking of putting it in the plastic covering by the wind-shield washer lever - you know, the one that covers the hole for the push start button?
I could get a rectangle shape laser cut, then laser cut a piece of thin plexi-glass to glue onto it, then put the screen below. That way the wires can run through the hole, and I could still see it while driving.
Not the best solution but I think that is where I am going to place mine.
I could get a rectangle shape laser cut, then laser cut a piece of thin plexi-glass to glue onto it, then put the screen below. That way the wires can run through the hole, and I could still see it while driving.
Not the best solution but I think that is where I am going to place mine.
About time, but I wanted all the other cool functions too lol. Can't have everything I guess? lolOriginally Posted by CTScott ↑For 2010 all manual transmission LBs come with the tach. Autos still do not.
Scott, your product is 50x cooler than the scanguage and developed IN HOUSE SPECIFICALLY for people who own Yarii. That makes it more enjoyable and rewarding to own and use.Originally Posted by CTScott ↑I actually have one on my test bench. I don't see being able to mount it within the tach cluster without modification, so I am looking for someplace outside of the cluster. For example, one thought is to mount it in place of one of the center AC vents. I am open to suggestions.
I obviously could mount it in a small enclosure, that you can put anywhere (like the scangauge), but that diminishes its value versus products like scangauge.
For example when people get in my car I proudly tell them that some crazy CT electrical engineer fabricated up a switch for my airbags.
This is a great project and you shouldn't fear the scangauge because yours is going to be way better!
Also, as an owner of a tach, I would like to see a version of it fit under my single DIMM head unit or as an AC vent replacement, both are great ideas.
Good idea! 👍Originally Posted by advocate ↑Also, as an owner of a tach, I would like to see a version of it fit under my single DIMM head unit or as an AC vent replacement, both are great ideas.
Awesome work CTScott, it's looking amazing :) 🙌 for this
Update: 1/20/2010 - Final design review and testing:
After installing the proto in my Yaris and driving around with it for a week, I found that bright sunlight was a major problem. This time of year, most of my driving is either in the dark or on overcast days, so it took a few days to encounter the worst case conditions.
After speaking with some display manufacturers about the issue, I was able to find a different type of display that is far more sunlight readable. I explored many options, including many that would have doubled to price of the product. The display I finally chose fits better within the space, so it is not recessed, as the original had to be. Also, the text is black on white or orange (other colors will be available as well), so the display is similar to the fuel gauge, rather than the original clock display.
Picture not included in this copy
Here is a list of all of the current features. If there are any additional requests let me know ASAP, as I am preparing to cut the final version of the circuit board.
1. Clock and outside temperature on second line.
2. Display modes for top line:
a. RPM numeric
b. RPM bargraph
c. Fuel Economy (MPG)
d. Battery Voltage
e. Coolant Temp
f. Intake Air Temp
g. Fuel system status
h. Calculated Engine Load %
i. Throttle Position %
j. Speed
k. Number of stored DTCs
l. List of DTC's
m. Clear DTCs / Reset MIL (Check engine light)
3. Programmable Shift Indicator / Light - This optionally displayed feature will display an indicator between the time and temp on the second line. Considering the small size of the display, this feature will also have a 2 wire output that will drive your choice of LED, mounted wherever you choose.
4. Cruise Control Indicator - For those with 06-08 Yaris, who have done the DIY cruise control, this feature will display an indicator between the clock and temperature to indicate that cruise control has been activated. This will require a one wire connection to your DIY switches or OEM CC stalk.
5. Automatic Dimmer - The new display is much brighter than the original, so I found that I absolutely needed the dimmer feature.
6. Configuration options
a. US or Metric units
b. Time display - 12 or 24 hour
c. Shift light enable/disable
d. Cruise Control Indicator enable/disable
After installing the proto in my Yaris and driving around with it for a week, I found that bright sunlight was a major problem. This time of year, most of my driving is either in the dark or on overcast days, so it took a few days to encounter the worst case conditions.
After speaking with some display manufacturers about the issue, I was able to find a different type of display that is far more sunlight readable. I explored many options, including many that would have doubled to price of the product. The display I finally chose fits better within the space, so it is not recessed, as the original had to be. Also, the text is black on white or orange (other colors will be available as well), so the display is similar to the fuel gauge, rather than the original clock display.
Picture not included in this copy
Here is a list of all of the current features. If there are any additional requests let me know ASAP, as I am preparing to cut the final version of the circuit board.
1. Clock and outside temperature on second line.
2. Display modes for top line:
a. RPM numeric
b. RPM bargraph
c. Fuel Economy (MPG)
d. Battery Voltage
e. Coolant Temp
f. Intake Air Temp
g. Fuel system status
h. Calculated Engine Load %
i. Throttle Position %
j. Speed
k. Number of stored DTCs
l. List of DTC's
m. Clear DTCs / Reset MIL (Check engine light)
3. Programmable Shift Indicator / Light - This optionally displayed feature will display an indicator between the time and temp on the second line. Considering the small size of the display, this feature will also have a 2 wire output that will drive your choice of LED, mounted wherever you choose.
4. Cruise Control Indicator - For those with 06-08 Yaris, who have done the DIY cruise control, this feature will display an indicator between the clock and temperature to indicate that cruise control has been activated. This will require a one wire connection to your DIY switches or OEM CC stalk.
5. Automatic Dimmer - The new display is much brighter than the original, so I found that I absolutely needed the dimmer feature.
6. Configuration options
a. US or Metric units
b. Time display - 12 or 24 hour
c. Shift light enable/disable
d. Cruise Control Indicator enable/disable
1 attachment not included in this copy
Scott enough already!😁!!! All of YW can't wait anymore release it
👍 Wow amazing work, thanks for making this all happen and for making it at an affordable price. I would expect to pay a few hundred if this was offered from anyone else. Much respect my dude.
1) how does the user give it instructions ?
This is just amazing! Can't wait for final product!!!
All with the single button that you used before for the clock. Short press to change modes. Long press to set shift light in RPM mode, long press to set clock in any other mode.Originally Posted by 127.0.0.1 ↑1) how does the user give it instructions ?