Yarisworld Archive

GI: "YarGauge" replacement clock module (Digital Tach, etc.)

737 posts · 304,493 views · page 1 of 15

CTScottOriginal postUSA, CT · Sep 1, 2009#1
A while back there was a discussion about converting the clock on the cluster to a digital tach. I have been exploring this a bit more and am looking at creating a replacement module for the clock that would have an 8 character display and would allow you to switch between the following functions (using the same push button that is used currently to set the clock):

1. Tachometer (RPM 9999)

2. Diagnostic trouble code read/reset (DTC 9999) (If more than one code is present it would scroll between the stored codes). Holding the button for 5 seconds would clear the stored code(s).

3. Water Temp (WT 999F) or (WT 999C)

4. Battery Voltage (VOLT 99.9)


And, probably a few more. Maybe even MPG (instant and average), if I can figure out how to calculate those from the available data.

It would remember the last display choice and F or C for temp.

Installation would require popping the cluster out, removing the clock module (a separate chuck held to the back of the cluster with some tabs), disconnecting the clock connector, replacing the clock's circuit board with mine (pop a couple of tabs and remove two screws), reconnect the clock connector to my module, and tap four wires onto the other cables going to the cluster.

Target price would be $75. The question is at that price, would there be enough interest to make it worth my time?




Note: Jump to post 512 of page 29 to see how this has evolved:
GI: "YarGauge" replacement clock module (Digital Tach, etc.)

The original price estimate was based on using an very inexpensive display. Through my development testing I found that the cheap display (and a couple of other more expensive displays) just wouldn't work well with sun glare on the cluster. In my quest for a better display to combat this issue, I settled on a high-end, full color OLED display. The chosen display unfortunately costs $79, which is more than the original target price, so the current target has moved to $150-$200. This additional cost did bring about some great features that were not possible with the cheaper displays...

Replies 736

ezhacker1San Francisco · Sep 1, 2009#2
Wow what a great idea would be very oem. I was just expecting it to be tach but if it has all those features 75 isn't bad all.
AltitudeColorado · Sep 1, 2009#3
I think $75 is very reasonable. You might consider adding an automatic function to switch between the different readings every few seconds.

As for calculating MPG from available data, I found some sites on the net that discuss it only I can't remember the site name. It may have been from MP3Car.com or some OBDII developer site, but it is out there. If I can find the link (I think I have it bookmarked on my laptop) I'll post it.
contraband831CEN*CAL · Sep 1, 2009#4
that sounds awesome! ***I voted on the poll and it sent me to another thread***
talcumWI · Sep 1, 2009#5
$75 sounds great. I've been contemplating how to do exactly what you're talking about.

Bob
ChinoCharlesOH · Sep 1, 2009#6
Ummmm yes.
TinyGiantRochester, NH · Sep 1, 2009#7
i'd certianly save up for one of these. i could sell my voltage meter to it :)
POORSHANE CT · Sep 1, 2009#8
I am in
cali yarisCanoga Park, CA · Sep 1, 2009#9
I'll take 25. Whatever guarantees you'll make this, it's the coolest mod I've heard about in a long while (and I can't even use it for myself 😢 )
ezhacker1San Francisco · Sep 1, 2009#10
how bout see if you can get (miles to empty) im curious to what other features you can implement, would be better than a SGII just cuz its oem looking.

And as we know that you are very well educated in electronics and stuff, we wont just get our hopes up. Man im excited.
IsLNdbOiLas Vegas, NV · Sep 1, 2009#11
Would the clock function be preserved and be one of the functions you could cycle through?
CTScottThread starterUSA, CT · Sep 1, 2009#12
Originally Posted by IsLNdbOi ↑
Would the clock function be preserved and be one of the functions you could cycle through?
Possibly. That's why I put the "I still want the clock" option on the poll. Adding the clock is not a huge deal, I just wasn't sure if people would still want it.
GMKingPortsmouth VA · Sep 1, 2009#13
at 75 dollars i'd buy that right now
1NZYaris1New Zealand · Sep 1, 2009#14
Doh me bad i voted in the wrong box , i would take one .🙇🙇
lilredrocketDFW, Texas · Sep 1, 2009#15
Do it!!!!!!!!
ezhacker1San Francisco · Sep 1, 2009#16
question: would this interfere with say my Ecometer? seeing im guessing that your module whatever would take signals from the obd2. Im not all that knowledge about the matter, but i read on other forums when searching, that 2 devices getting signals from same source would show errors on one of the devices. Now to me i just thought that splice the obd2 connector, have 2 female ends = 2 devices.

I just dont want to give up my ecometer.
aruntoIndy · Sep 1, 2009#17
i'm in for one!!
heeroyuy01195Florida · Sep 1, 2009#18
I'm in but I still want to be able to use my clock :)
CTScottThread starterUSA, CT · Sep 2, 2009#19
OK. So far it looks like I'll keep the clock function. The other function that I am thinking of adding is inside and outside temperature.

I will also be experimenting with 1 line vs 2 line LCDs to see what will fit in the slot that the clock peeks through. the slot is actually about 1 5/8" x 5/8", so it may be possible to squeeze a 2 line by 8 character LCD in there, which would allow the clock or temp to be displayed simultaneously with one of the other items.

Also, the RPM measurement will be done directly (via the Tach input wire to the meter), rather than through the CAN comm with the ECM. This will make it more responsive than the devices that get it second hand from the ECM.
cali yarisCanoga Park, CA · Sep 2, 2009#20
^ AWESOME. I would pay $150-200 for a device like this.
devinlamotheSudbury, Canada · Sep 2, 2009#21
This is amazing. I would definitely buy this!!

Just a question though ... what colour would the LCD be?
ezhacker1San Francisco · Sep 2, 2009#22
maybe some kind of option for color? Im sticking with the stock 09 amber colors, i have leds and cathodes made around that.
47_MasoN_47Northwest Alabama · Sep 2, 2009#23
Sign me up! I'd love one of these. $75 sounds like a reasonable price to me. I would like to keep the clock though also :)
AltitudeColorado · Sep 2, 2009#24
Originally Posted by cali yaris ↑
^ AWESOME. I would pay $150-200 for a device like this.
Shhhhh! It is a great idea, but unless it does everything a Scanguage does at $150, it shouldn't be more than $100.
advocatelocation · Sep 2, 2009#25
Garm's wallets are deeper than our I think unfortunately 😢

This does sound amazingly well thought out and a great mod overall. Would be hard not to want to buy one that's for sure.
CTScottThread starterUSA, CT · Sep 2, 2009#26
Originally Posted by devinlamothe ↑
This is amazing. I would definitely buy this!!

Just a question though ... what colour would the LCD be?
I'm prototyping on a greenish one, because I have it lying around. For production I will at the very least offer versions to match the two current colors of clocks. I looked into VFDs, which are what the clock displays are. A character one (as opposed to just 7-segment numbers) is about as expensive as the target price, so it looks like it will be LCD for sure.
IsLNdbOiLas Vegas, NV · Sep 2, 2009#27
This is going to be cool. I'd want it amber though like all the other stuff in my '09.
AlexNet0Rockland, ME · Sep 2, 2009#28
I'm definitely down for one of these. clock option would be ideal, but not a necessity.
1NZYaris1New Zealand · Sep 3, 2009#29
question , is the clock in the US models to the right or left of speedo

1 attachment not included in this copy

dvlnblkdrsorange, ca · Sep 3, 2009#30
i believe 07s have it on the left and 08+ have it on the right.. cuz mine is on the left as well... and yes, id be down 😁
IsLNdbOiLas Vegas, NV · Sep 3, 2009#31
Originally Posted by 1NZYaris1 ↑
question , is the clock in the US models to the right or left of speedo
The clock on my 5-door '09 is where yours is.
1NZYaris1New Zealand · Sep 3, 2009#32
Mine also has the mpg and the likes but it is not pluged in 😳
i can take a photo of it tommorrow and paste it up here 👍
CTScottThread starterUSA, CT · Sep 3, 2009#33
On the OEM cluster with the tach, the clock is integrated into the part where the fuel gauge and odometer are located.

My module will only be for non-S clusters, which have the separate clock module on the left of the speedometer.
devinlamotheSudbury, Canada · Sep 3, 2009#34
Originally Posted by CTScott ↑
On the OEM cluster with the tach, the clock is integrated into the part where the fuel gauge and odometer are located.

My module will only be for non-S clusters, which have the separate clock module on the left of the speedometer.
Well that leaves out every Canadian model, since we all have our clocks with the fuel gauge on the right.

Nooooooo. 😢
CTScottThread starterUSA, CT · Sep 3, 2009#35
Originally Posted by devinlamothe ↑
Well that leaves out every Canadian model, since we all have our clocks with the fuel gauge on the right.

Nooooooo. 😢
Interesting. So, all Canadian Yaris have tachs, or just have the clock as part of the fuel gauge?
SpeedjunkiejpJacksonville, FL · Sep 3, 2009#36
i dont get it, i run my vin and it comes back a non-s but i have integrated radio and a tach. guess I am out of this :-(
CTScottThread starterUSA, CT · Sep 3, 2009#37
If there's enough interest for non-left hand clock people, I'll just offer a "packaged" option, where the device is in a plastic box like a ScanGauge.
47_MasoN_47Northwest Alabama · Sep 3, 2009#38
I have a 2009 sedan and my clock is on the right.
devinlamotheSudbury, Canada · Sep 4, 2009#39
Originally Posted by CTScott ↑
Interesting. So, all Canadian Yaris have tachs, or just have the clock as part of the fuel gauge?
We all have tachs + the clock is part of the fuel guage setup.
1NZYaris1New Zealand · Sep 4, 2009#40
I think all the Yaris over here have Tach's as well , at least in the Hatch back they do
Cause we have the Digital dash 😁
i am more interested in water temp , and fuel mileage .
just so you know 😆
And THANK YOU VERY MUCH , for even looking to do this . 🙇 🙇 🙇
bladesmith6PA · Sep 4, 2009#41
No you're pretty much correct only the US manual trans liftbacks got completely fucked. toyota usa engineering idiots...
yarstarGeorgia · Sep 4, 2009#42
Originally Posted by bladesmith6 ↑
No you're pretty much correct only the US manual trans liftbacks got completely fucked. toyota usa engineering idiots...
I COMPLETELY AGREE.

CT: I am so down with this! You wlll solve the 'no tach' issue very OEM and I can finally get rid of my aftermarket tach.

I love the idea of an outside temp option.

I agree with Garm. This a a great idea and I will buy it a heartbeat.
IsLNdbOiLas Vegas, NV · Sep 4, 2009#43
Originally Posted by CTScott ↑
If there's enough interest for non-left hand clock people, I'll just offer a "packaged" option, where the device is in a plastic box like a ScanGauge.
If this turns into a an external device (like smaller version of the ScanGauge) and turns out it's not going to be a replacement for the digital clock, then count me out.

Also, to get outside temps. you'll need to sell a thermometer probe like the kinds used with Gentex and CIPA rear-view mirrors that show outside temps., right?
CTScottThread starterUSA, CT · Sep 4, 2009#44
Originally Posted by IsLNdbOi ↑
If this turns into a an external device (like smaller version of the ScanGauge) and turns out it's not going to be a replacement for the digital clock, then count me out.

Also, to get outside temps. you'll need to sell a thermometer probe like the kinds used with Gentex and CIPA rear-view mirrors that show outside temps., right?
For the right hand clock clusters, there's no place within the cluster to mount it (without cutting plastic). My original thought with this whole thing is that it would really be for the tachless people. It started off as simply a tach in place of the clock and then the more I thought about it the more features that kept popping to mind.

Correct on the sensor probe for outside temp (although if I can figure out the CAN messaging for the A/C ECU, I can use it's outside temp probe and save people having to run a probe wire through the firewall).

I am making great progress on this. I built a CAN bus interface this week and can read the PIDs (all of the standard OBD data), can read and reset stored DTCs, and can sniff the communication on the CAN bus between the ECM and the body ECUs.
1NZYaris1New Zealand · Sep 4, 2009#45
Progress, is good , you so need a Yaris Medal of Honor 😁 🙇 🙇
TamagoOff Grid · Sep 4, 2009#46
i want one and i don't even have a clock
IsLNdbOiLas Vegas, NV · Sep 4, 2009#47
So are you planning on two versions? One being a replacement for the clock module for the ones with the left hand clock and one for those with the right hand clock?

The whole allure in this in the beginning was in replacing the clock with a multi-function device that fit in the same spot.
CTScottThread starterUSA, CT · Sep 4, 2009#48
Originally Posted by IsLNdbOi ↑
So are you planning on two versions? One being a replacement for the clock module for the ones with the left hand clock and one for those with the right hand clock?

The whole allure in this in the beginning was in replacing the clock with a multi-function device that fit in the same spot.
The right hand clocks can't really be replaced, since that display is non-removable and integrated into that display is quite a bit more than just the clock. You just have to figure out another place on the dash where it can be installed to still look OEM. Maybe there's something else that we can pop and replace on cars like yours.
IsLNdbOiLas Vegas, NV · Sep 5, 2009#49
Originally Posted by CTScott ↑
The right hand clocks can't really be replaced, since that display is non-removable and integrated into that display is quite a bit more than just the clock. You just have to figure out another place on the dash where it can be installed to still look OEM. Maybe there's something else that we can pop and replace on cars like yours.

Oh no, I was just wondering. My clock is on the left like all other 5-door '09s in the US.
l2a3k2a3iOklahoma City, Oklahoma · Sep 5, 2009#50
Count me in. Ill buy one in a heartbeat!!1