That is awesome and very clean looking (especially since I painted my centre console black, so this will be very sleek).Originally Posted by CTScott ↑I test mounted it to a vent with some sheet ABS that I had on hand. The push button will be to the left of the display, like the clock replacement one.
GI: "YarGauge" replacement clock module (Digital Tach, etc.)
737 posts · 304,493 views · page 6 of 15
Replies continued
come on scott when are you releasing it?hehe... when he's done! seriously though, there's going to be a rush on these I think... 👏
what gets in the way? is it just plastic or are there electronics there.... i dont mind hacking up some plastic LOL..Originally Posted by CTScott ↑There's not enough room behind the clock VFD on your cluster, but for US and Canadian clusters with tachs and digital clusters like yours, I am going to offer alterternative mounts as a single DIN plate (for those using a single DIN aftermarket radio) and a mount that replaces the left center A/C vent.
or is it possible to have one with a remote screen so to speak, eg. put the electronics in a box and have the screen itself plug in?
The circuit board is right behind it.Originally Posted by mick.wheelz ↑what gets in the way? is it just plastic or are there electronics there.... i dont mind hacking up some plastic LOL..
or is it possible to have one with a remote screen so to speak, eg. put the electronics in a box and have the screen itself plug in?
Ahh its just a circuit board hahahahahahaOriginally Posted by CTScott ↑The circuit board is right behind it.
I would not be surprised if i can't get a hold on one
Originally Posted by cali yaris ↑hehe... when he's done! seriously though, there's going to be a rush on these I think... 👏
I'm hip!
God I am waiting for this soooooooooooo bad
I am supposed to receive the first 5 production PCB sets this week. If all is well with them I will let them cut the first production run (100 PCB sets). In the meantime I am working on wrapping up the firmware. I figured out how to get the cluster to tell me the raw reading of the fuel level sender, so the numeric fuel level / range until empty won't require a wire to be tapped. I am now working on getting the ECM to give up the air to fuel ratio.
No words: 🙇🙇🙇🙇🙇🙇🙇🙇🙇🙇 🙇🙇Originally Posted by CTScott ↑I am now working on getting the ECM to give up the air to fuel ratio.
Scott, that left side vent mount will be perfect for me, especially in that orange RS glow with black backing...just installed RS trim pieces and a/c heater control knobs as well so black on black match.
My understanding is that he can read memory addresses but would need the machine code to write to the ECM. Reverse engineering the machine code is problematic, and Toyota doesn't share it.
Have I got that right?
Have I got that right?
Whenever you start taking orders for this I have my $$ ready for you. 😁😁😁
That's correct.Originally Posted by cali yaris ↑My understanding is that he can read memory addresses but would need the machine code to write to the ECM. Reverse engineering the machine code is problematic, and Toyota doesn't share it.
Have I got that right?
I am making a bit more progress with being able to write to the ECM, for example I figured out the CAN message to make the ECM turn on/off the radiator fan at will.
For the question above about the AFR - The Yaris' O2 sensors are wide band zirconia sensors.
i have a feeling this product will never come out, so many requests for more and more things to be adde, LOL I kid i kid.
In the Engineering world we call it "feature creep". Marketing people love it (not) when we Engineers keep wanting to add just "one more little thing" before release...Originally Posted by ezhacker1 ↑i have a feeling this product will never come out, so many requests for more and more things to be adde, LOL I kid i kid.
^ and building a website for a client is exactly like that too!
And ordering take out is like that too
The best way to eliminate feature creep would be if the YarGauge were updatable via a serial connection... That would basically allow you to ship now and add features later on.Originally Posted by CTScott ↑In the Engineering world we call it "feature creep". Marketing people love it (not) when we Engineers keep wanting to add just "one more little thing" before release...
Then again, that would raise the final price for sure. Which I wouldn't mind doing BTW.
The tricky part to that is that it consists of two separate processors, each of which requires a different interface for programming.Originally Posted by tk-421 ↑The best way to eliminate feature creep would be if the YarGauge were updatable via a serial connection... That would basically allow you to ship now and add features later on.
Then again, that would raise the final price for sure. Which I wouldn't mind doing BTW.
Oil pressure is a funny one - The Yaris simply has a pressure switch that is on if there is oil pressure or off if you don't.Originally Posted by camelll ↑That is nice about the 02 sensors. Someone can save a fortune on a good gauge and get their a/f wideband from this product. Can you get oil pressure as well?
Well I am sure if you ever get to a point where you can do fuel maps, you will have a lot of people interested.
Just curious, what do you do? Electrical engineer?
I am an Electrical Engineer,
I am still sold on it if it has a tach and nothing more......lol......we are very lucky to have someone here to construct something like this and I meen we area lucky.......this is very cool.Originally Posted by Lewis ↑image this all started with needing a tachometer!
from tiny acorns grow mighty oaktrees.
I can't wait for version 2 that will have a 4x25 character display and it's own plastic case.
OK wishful thinking... I just want it to match my V2 ECUTalk 😛
I am loving this project but I don't want it to mount in my AC vent or DIN slot.
OK wishful thinking... I just want it to match my V2 ECUTalk 😛
I am loving this project but I don't want it to mount in my AC vent or DIN slot.
i've asked before, i'll ask again..
since this is OBD2 driven, will it work on any other "like coded" OBD2 system? (my MR2) if so i DO WANT ONE
since this is OBD2 driven, will it work on any other "like coded" OBD2 system? (my MR2) if so i DO WANT ONE
Originally Posted by Tamago ↑i've asked before, i'll ask again..
since this is OBD2 driven, will it work on any other "like coded" OBD2 system? (my MR2) if so i DO WANT ONE
It's OBDII, but OBDII CAN, so it will only work for vehicles that use CAN bus (which is all vehicles 2008+ and many 2005+). Your MR2 is ISO-9141 based, which is one of the older hardware standards for OBDII. So, the YarGauge won't support your MR2.
I agree. I fully intend to pick one of these up for the tach. Everything else is just glitter to me. Wonderful, glorious, distracting glitter.Originally Posted by bzinn 1 ↑I am still sold on it if it has a tach and nothing more......lol......we are very lucky to have someone here to construct something like this and I meen we area lucky.......this is very cool.
So, by that it would work in an 09 Tacoma, I assume? Are there any Yaris specific codes in there or do you think the readings would work well out as long as he tapped the same wires?Originally Posted by CTScott ↑It's OBDII, but OBDII CAN, so it will only work for vehicles that use CAN bus (which is all vehicles 2008+ and many 2005+).
One of the EE's in my office is looking to do this for his Taco' after I started telling him about yours... If yours is done already, I'll push him toward remote vent mount... I'm an ME, so this is all sparky stuff to me 🤷
It definitely should work on the 09 Tacoma. So far, all of the CAN messages I am using are either OBDII compliant or are Toyota enhanced messages (air to fuel ratio and fuel level for example).Originally Posted by dean_park ↑So, by that it would work in an 09 Tacoma, I assume? Are there any Yaris specific codes in there or do you think the readings would work well out as long as he tapped the same wires?
One of the EE's in my office is looking to do this for his Taco' after I started telling him about yours... If yours is done already, I'll push him toward remote vent mount... I'm an ME, so this is all sparky stuff to me 🤷
Awesome thanks for the info Scott. God's speed on finishing it all up. If we were normal executives we would probably hate feature creeping however we are but humble customers and I for one am grateful for each gadget that gets added on.
HOLY SHIT! i was asking about this sometime ago.
$75 sound great for those functions.
$75 sound great for those functions.
Sad :(Originally Posted by CTScott ↑It's OBDII, but OBDII CAN, so it will only work for vehicles that use CAN bus (which is all vehicles 2008+ and many 2005+). Your MR2 is ISO-9141 based, which is one of the older hardware standards for OBDII. So, the YarGauge won't support your MR2.
I did design the hardware interface to be modular, and I have done HW/SW for the older OBDII standard, so once the CAN version is released, I may very well make a ISO9141 version or a combo version. A couple friends of mine really want the functionality of this for their Mazda, Subaru and Honda cars (most of which predate CAN).Originally Posted by Tamago ↑Sad :(
I found out today that my boards are delayed for two weeks, due to the "Spring Festival" holiday in China (the board house that I use is over there).
A part of me died inside.Originally Posted by CTScott ↑I found out today that my boards are delayed for two weeks, due to the "Spring Festival" holiday in China (the board house that I use is over there).
Just kidding! 😁
Me too!Originally Posted by devinlamothe ↑A part of me died inside.
Just kidding! 😁
I paid for 1 day express shipping, which should have put them in my hands yesterday. I emailed my contact this morning to find out what the deal was, and he informed me about the holiday shutdown.
Scott- even my wife is looking forward to the Yargauge! I couldn't believe it today when she asked me when I'd be getting the gadget that tells us the outside temperature.
When wives who don't care much about cars start to want an aftermarket automotive item Scott you KNOW you have a winner!!!!!!!!
When wives who don't care much about cars start to want an aftermarket automotive item Scott you KNOW you have a winner!!!!!!!!
I just kind of picked up this thread now... Maybe sometime when I'm bored enough I'll read through it all -- unless someone wants to give a 17 page summary of events? lol There should be a rule about things like this...
17 pages = one sentence... and .... go:
CTScott is making an LED (LCD?) gauge display that replaces your OEM clock and gives you lots of data choices to read: rpm/tachometer, clock, and other functions, for about seventy five bucks.
CTScott is making an LED (LCD?) gauge display that replaces your OEM clock and gives you lots of data choices to read: rpm/tachometer, clock, and other functions, for about seventy five bucks.
yay
page 12, post 209 has a good overview... if u start there and then read on to see that CTScott added AFR and fuel level and miles to empty over the next few pages.
Split the thread to keep things on topic:
Sony RM-X4S adapter for JVC KD-AVX77?
Sony RM-X4S adapter for JVC KD-AVX77?
CTScott, my man :) Count me in on this one 👍
Tell me, will I be able to upgrade SW in this module to read TRC VSC status? You know, regarding my custom VSC switch for 2008 TS. That is the only model that can really use that feature, so I don't want you to include it in mass production version.
Tell me, will I be able to upgrade SW in this module to read TRC VSC status? You know, regarding my custom VSC switch for 2008 TS. That is the only model that can really use that feature, so I don't want you to include it in mass production version.
That might just be possible. I have recently figured out many of the status messages between the ECM and the other ECUs (ABS ECU, Power Steering ECU, SRS ECU, Body ECU, Combination Meter ECU, A/C ECU).Originally Posted by Stiv ↑CTScott, my man :) Count me in on this one 👍
Tell me, will I be able to upgrade SW in this module to read TRC VSC status? You know, regarding my custom VSC switch for 2008 TS. That is the only model that can really use that feature, so I don't want you to include it in mass production version.
😲😲😲Originally Posted by CTScott ↑I have recently figured out many of the status messages between the ECM and the other ECUs (ABS ECU, Power Steering ECU, SRS ECU, Body ECU, Combination Meter ECU, A/C ECU).
If you can get it to display ABS codes that would be awesome. Then I can see which wheel sensor is messed up so I can either clean or replace it.
The piece I am working on now (while waiting for my PCB's), is being able to get fault codes from all of the subsystem ECUs.Originally Posted by devinlamothe ↑If you can get it to display ABS codes that would be awesome. Then I can see which wheel sensor is messed up so I can either clean or replace it.
CTscott
Any idea when you are gonna start shipping these little bad boys? I can't wait to get my hands on one!
Any idea when you are gonna start shipping these little bad boys? I can't wait to get my hands on one!
Awesome!Originally Posted by CTScott ↑The piece I am working on now (while waiting for my PCB's), is being able to get fault codes from all of the subsystem ECUs.
lol once we stop asking him to add stuffOriginally Posted by 2009BBPliftback ↑CTscott
Any idea when you are gonna start shipping these little bad boys? I can't wait to get my hands on one!
The Mad Scientist at work. Awesome stuff as usual Scott!