Yarisworld Archive

GI: "YarGauge" replacement clock module (Digital Tach, etc.)

737 posts · 304,493 views · page 10 of 15

Replies continued

KioshiFremont, CA · Aug 29, 2010#451
CTScott, I use to use this mp3 player back in high school - http://asia.cnet.com/reviews/musicpl...6925p-1,00.htm

It used OLED technology and I was able to read song titles walking around the border of the school during lunch time in the sun.
I don't think it should be a problem i the YarGauge as well because the cluster sits a little angled down in the area, doesn't it? it isn't directly sitting flat per say....at least when you install/remove it, it mounts a little tilted...
CTScottThread starterUSA, CT · Aug 29, 2010#452
Originally Posted by sleey0 ↑
Unless it is Super-AMOLED, which I highly doubt, you have it backwards.

OLED displays are very nice and produce rich colors and deep blacks, but their worst flaw is daylight visibility, which is pretty weak. I wish OLED had great visibilty in the sun but they do not. The reason being is there is no backlight which is found on a traditional LCD. Instead, it uses a bioelectrical chemical to light and this washes out badly in the sun.

Just warning you before you make a mistake and buy them.
That was my impression as well. The VAR that is sending me the samples claims that they are a vast improvement over earlier generations of PMOLED displays. I guess we'll see. As Kioshi mentioned, the display is not in direct sunlight, so perhaps the high contrast ratio behind the smoked lens will do it. The gas gauge is just a backlit transflective LCD, but it is a higher contrast one than I've been able to source.
Biffa point or extent in space. · Aug 29, 2010#453
i'm in for one!!
JumpmanYarisSO. INDIANA · Aug 29, 2010#454
Originally Posted by Biff ↑
i'm in for one!!
You sure about that?

dont have anything to say about this ?
Nexus1155Dorchester · Aug 29, 2010#455
You sure about that?

dont have anything to say about this ?
LOL unresolved issues?


Getting psyched this thing is getting close to completion CTSCott. I'm sure you'll sell a ton, to Garm atleast :P Hope it isn't hard to swap it in there.
JumpmanYarisSO. INDIANA · Aug 30, 2010#456
Originally Posted by Nexus1155 ↑
LOL unresolved issues?
Na, just has to say something always..
Nexus1155Dorchester · Aug 30, 2010#457
ah just looked up his posts... one of THOSE people :P
Biffa point or extent in space. · Aug 31, 2010#458
Yup, one of those ppl
Biffa point or extent in space. · Aug 31, 2010#459
Originally Posted by Nexus1155 ↑
ah just looked up his posts... one of THOSE people :P
What posts are you referring to? I don't know what you guys problem is.
teddyOntario, Canada · Sep 1, 2010#460
I'm sorry if this has been addressed already in the thread but I have a couple questions:

Will this work in a Canadian Yaris? I have a 5-door automatic with tach. I'm guessing probably yes, but it'd be nice to be sure.

Were you able to come up with instant fuel economy? Especially interested in L/100km if possible.

EDIT: I searched the thread and found both these questions were answered. Looking forward to seeing this project to completion, and likely buying up one myself if possible!
RevssonSoutheast Wisconsin · Sep 1, 2010#461
Originally Posted by teddy ↑
I'm sorry if this has been addressed already in the thread but I have a couple questions:

Will this work in a Canadian Yaris? I have a 5-door automatic with tach. I'm guessing probably yes, but it'd be nice to be sure.

Were you able to come up with instant fuel economy? Especially interested in L/100km if possible.

EDIT: I searched the thread and found both these questions were answered. Looking forward to seeing this project to completion, and likely buying up one myself if possible!


Teddy -
Since you asked before searching, you have to go to the back of the line! 😠

j/k 😁 ....or maybe not....
CTScottThread starterUSA, CT · Sep 3, 2010#462
I received my sample OLED display today and did a bit of experimentation with it tonight. The display is amazing on the bench, but they all start out that way. This display is a 16 bit color OLED display. For initial testing I am just running it with white text on a black background.


I mounted it in Crashy's cluster for a quick test and will put her cluster in my 09 tomorrow to do some sunlight testing.

Picture not included in this copy

1 attachment not included in this copy

mr9865Green Bay WI · Sep 3, 2010#463
looks nice
auxmikeLI, New Yawk · Sep 4, 2010#464
Small text, but it looks BEAUTIFUL!🤤
Nexus1155Dorchester · Sep 4, 2010#465
kestion. Are the RPMs reflected in real time or have a slight lag to it like some digital rpm display readings?

Also, does the text change color :) or backlighting w/e?
CTScottThread starterUSA, CT · Sep 4, 2010#466
The text is actually bigger than the two prior displays that I tested. This one has programmable fonts, so I loaded a font that maximizes the space of the clock display opening.

The data is more realtime than other comparable devices, due to the speed of the CAN bus processor that I am using. The hysteresis of the display becomes the limiting factor.

The text can be any of 65535 colors with this display. The background can be any color as well, although the manufacturer recommends bright text on a dark background, rather than dark text on a bright background, due to a smearing effect that happens with OLED displays.

There's not a cloud in the sky this morning, so today will provide a good test for the sun glare visibility of this one.
sleey0PA · Sep 4, 2010#467
I am rooting for you.

Man, you are one intelligent person. Wish I knew how to do these things!


GL!!!!
Nexus1155Dorchester · Sep 4, 2010#468
Just what I wanted to hear. I was also thinking color for those of us who want to keep it stock looking or go with our already red motif ;)
swiddCentral Alabama, GOD BLESS AMERICA · Sep 5, 2010#469
That looks mighty fine to me! How hard would it be to attach a wire with some knobs to allow custom adjustment of colors? Something that could be pulled to the bottom of the dash for example...
CTScottThread starterUSA, CT · Sep 5, 2010#470
So, the sun glare testing has been interesting. Yesterday, I was out with it from 9:30AM to 11:30AM, and couldn't get it to a point where the glare was bad enough to make it unreadable.

Today, I was out with it from 11:30 AM to 2:00 PM. During that time the sun was almost dead overhead. With the sun shining directly vertical down through the windshield, the glare was bad enough to make it very difficult to see. It didn't get washed out, like the transflective LCD, but without shading it with my had, it was quite difficult to see. At that same time though, the fuel gauge was nearly unreadable and even the speedometer was hard to see.
IsLNdbOiLas Vegas, NV · Sep 5, 2010#471
So this test was done with the improved LCD or OLED?
auxmikeLI, New Yawk · Sep 5, 2010#472
Sounds like it's a go if you ask me.
Can't perform miracles in such a small area.
CTScottThread starterUSA, CT · Sep 5, 2010#473
Originally Posted by IsLNdbOi ↑
So this test was done with the improved LCD or OLED?
The OLED pictured above.
aruntoIndy · Sep 6, 2010#474
woot can't wait!
PatrickJohnsonMurfreesboro, TN · Sep 6, 2010#475
Yes, this is promising. I'm definitely in, I say you are ready to go!
id3379Sep 6, 2010#476
This looks amazing
jarrietaPhilippines · Sep 6, 2010#477
Looks good, count me in!
CTScottThread starterUSA, CT · Sep 6, 2010#478
I've been experimenting a bit more with the capabilities of this display. Since it is full color with graphics capability I decided to add a bar graph to the RPM display. Here's the result (with orange text to match my 09's cluster):

Picture not included in this copy

And here's a video of it in action with feeding it random values between 0 and 8000 RPM to see how it could handle bouncing around. The bar is green up to 4000, yellow up to 6000, and red above that. I just arbitrarily set those thresholds.


Picture not included in this copy

1 attachment not included in this copy

tk-421Dagobah · Sep 7, 2010#479
Looking great! 👍
dean_parkWentzville, MO · Sep 7, 2010#480
Looks great CTScott. When I saw the pic, I was surprised you were rev'ing at 7747RPM... bench testing is definitely better. lol

The bar graph is great being displayed with the other features. I wanted this mainly for the tach feature and I was happy enough with a few dots/lines or just a numeric value, but this is far beyond. Can't wait for this!!
RedRideMiddletown, NY · Sep 7, 2010#481
How about a pic with some differnt values such as coolant temp or volts?

Many of us either has a stock tach or, haa added a great after rmaket one
and wont be using the tach function.

It's looking great though.🙂
alamocoastieNY · Sep 7, 2010#483
When will it be for sale?
RevssonSoutheast Wisconsin · Sep 7, 2010#484
Looks good CTScott! 👍
CTScottThread starterUSA, CT · Sep 7, 2010#485
Originally Posted by RedRide ↑
How about a pic with some differnt values such as coolant temp or volts?

Many of us either has a stock tach or, haa added a great after rmaket one
and wont be using the tach function.

It's looking great though.🙂
I still have quite a bit of programing to do to convert each mode's output from the prior LCD display to this OLED. Once I make some progress, I'll post up some more pics/videos.
CTScottThread starterUSA, CT · Sep 7, 2010#486
Originally Posted by alamocoastie ↑
When will it be for sale?
It depends on how long it takes me to get everything converted over to the new display, and to cut a new PCB.
Lucas13Fort Lauderdale · Sep 8, 2010#487
Great Job Scott every day this is looking better! Can't wait for the release day!!!
PhillyGgeorgia · Sep 8, 2010#488
somehow i think that when scott comes out with this product, its gonna be perfect! the design and implementation is truly awesome! i just hope i have the money when it comes out because i want one immediately!
mr9865Green Bay WI · Sep 12, 2010#490
anychance this will work on the echo?
CTScottThread starterUSA, CT · Sep 12, 2010#491
Originally Posted by mr9865 ↑
anychance this will work on the echo?
No. Unfortunately the echo predates CAN Bus for OBD communication.
mr9865Green Bay WI · Sep 12, 2010#492
ahh poop, scangauge for me
sleey0PA · Sep 12, 2010#493
Soooo, how close are you to making this happen?

I have a feeling you are going to make some decent money on this project. Time consuming yes, and I still think people will wait a month for there custom-made Yar-Gauge if gets to the point where it is a hot-seller.

CTScott, FTMFW!!
CTScottThread starterUSA, CT · Sep 12, 2010#494
Here's a video of what I have running thus far on the new display. I am still running it with my 09 cluster, connected to Garm's 07 ECM on my bench. By mid week I should have it ready to go back into the car.

http://www.youtube.com/watch?v=ZvQ68qXN39w
tk-421Dagobah · Sep 12, 2010#495
Excellent! There's a whole lot of functionality in there... You may want to consider having a "shortcut mode", in order to have my favorite functions close together (for instance, being able to switch between MPG and RPM readouts without having to press the button a number of times to get there). Am I making sense?

Great job all around, Scott! 👍
fmicleSan Jose, CA, USA · Sep 13, 2010#496
^ There is only so much programming you can do with one single button...
henry33slovakia · Sep 13, 2010#497
this look perfect :) will it be possible to change the MPG into L/KM or Miles into Kilometers ?
eTiMaGoBangkok, Thailand · Sep 13, 2010#498
🙇
henry33slovakia · Sep 13, 2010#499
What will be the connection OBD2 ? will it be possible to place it elsewhere since I have different gauges in my yaris ?
CTScottThread starterUSA, CT · Sep 13, 2010#500
Originally Posted by henry33 ↑
What will be the connection OBD2 ? will it be possible to place it elsewhere since I have different gauges in my yaris ?
It will have the option of switching between metric and imperial units. The first units will be the clock replacement ones, but I will also offer a standalone unit with a case as well as a one which will replace one of the center AC vents for those that want it integrated on sedans or liftbacks that already have a tach.