Yarisworld Archive

Looking at seats...

318 posts · 113,151 views · page 5 of 7

Replies continued

CTScottUSA, CT · Aug 18, 2009#201
Here's what the SM says:

Wait at least 90 seconds after the ignition switch is
turned off and the negative (-) terminal cable is
disconnected from the battery before starting the
operation.
(The SRS is equipped with a back-up power source, so
if work is started within 90 seconds of disconnecting
the negative (-) terminal cable of the battery, the SRS
may be deployed).
MGarganoThread starterNJ · Aug 18, 2009#202
I disconnected the battery overnight (about 13 hours or so) and tried it this morning... still nothing positive. All dash indicators are still lit.
CTScottUSA, CT · Aug 18, 2009#203
Try reading the codes from the SRS again.
MGarganoThread starterNJ · Aug 18, 2009#204
Originally Posted by CTScott ↑
Try reading the codes from the SRS again.
Same as before- 32, 55, & 56
CTScottUSA, CT · Aug 18, 2009#205
Here is the procedure for manually clearing the stored codes (The SM says that some codes do not clear with a power down):

1. With a jumper, connect the TC and CG terminals on the OBD port.

2. When the SRS light starts flashing the codes, within 3 to 10 seconds remove the jumper frm TC. After 3 seconds the SRS light will come on solid.

3. Within 2 to 4 seconds after the SRS lights, reconnect the jumper to TC.

4. Within 2 to 4 seconds the SRS light will go off. Once it does, within 2 to 4 seconds disconnect TC.

5. Within 2 to 4 seconds the SRS light will come one solid again. Within 2 to 4 seconds after the SRS lights, reconnect the jumper to TC.

6. Within 2 to 4 seconds the SRS light will go off. One second later, if all DTCs are cleared the SRS light will flash steadily on and off. If codes are still registered it will flash in the pattern to indicate the stored codes.
DorytheYarisJersey · Aug 18, 2009#206
Originally Posted by MGargano ↑
I'm looking to upgrade the front seats in my 09' hatch but I'm honestly not really sure what's out there, especially since some of the websites I checked out are crazy expensive. I'm just looking for something with good support, OEM function (sliding, reclining front and back, folding to let passenger's in back), and something lower to the ground.

I see these on fleaBay, but I'm not sure of the quality or fitment: http://cgi.ebay.com/ebaymotors/MAZDA...Q5fAccessories

Appreciate any help I can get with this.
If you get rid of your seats I WILL GLADLY buy your stock passenger seat from you! I need one desperately!!!!! and I am in NJ!!! 👍
MGarganoThread starterNJ · Aug 18, 2009#207
Originally Posted by DorytheYaris ↑
If you get rid of your seats I WILL GLADLY buy your stock passenger seat from you! I need one desperately!!!!! and I am in NJ!!! 👍
If I do decide to sell the OEM passenger seat it will most likely be without the four weight sensors. I haven't made up my mind about getting rid of the OEM seats yet though. I want to get the new ones working 100% before I get rid of the old ones. I'll definitely keep you in mind though.
MGarganoThread starterNJ · Aug 18, 2009#208
Originally Posted by CTScott ↑
Here is the procedure for manually clearing the stored codes (The SM says that some codes do not clear with a power down):

1. With a jumper, connect the TC and CG terminals on the OBD port.

2. When the SRS light starts flashing the codes, within 3 to 10 seconds remove the jumper frm TC. After 3 seconds the SRS light will come on solid.

3. Within 2 to 4 seconds after the SRS lights, reconnect the jumper to TC.

4. Within 2 to 4 seconds the SRS light will go off. Once it does, within 2 to 4 seconds disconnect TC.

5. Within 2 to 4 seconds the SRS light will come one solid again. Within 2 to 4 seconds after the SRS lights, reconnect the jumper to TC.

6. Within 2 to 4 seconds the SRS light will go off. One second later, if all DTCs are cleared the SRS light will flash steadily on and off. If codes are still registered it will flash in the pattern to indicate the stored codes.
Ok I'll give this a try ASAP. Thanks for posting the instructions.
DorytheYarisJersey · Aug 18, 2009#209
Originally Posted by MGargano ↑
If I do decide to sell the OEM passenger seat it will most likely be without the four weight sensors. I haven't made up my mind about getting rid of the OEM seats yet though. I want to get the new ones working 100% before I get rid of the old ones. I'll definitely keep you in mind though.
Thank you :)
MGarganoThread starterNJ · Aug 18, 2009#210
Originally Posted by CTScott ↑
Here is the procedure for manually clearing the stored codes (The SM says that some codes do not clear with a power down):

1. With a jumper, connect the TC and CG terminals on the OBD port.

2. When the SRS light starts flashing the codes, within 3 to 10 seconds remove the jumper frm TC. After 3 seconds the SRS light will come on solid.

3. Within 2 to 4 seconds after the SRS lights, reconnect the jumper to TC.

4. Within 2 to 4 seconds the SRS light will go off. Once it does, within 2 to 4 seconds disconnect TC.

5. Within 2 to 4 seconds the SRS light will come one solid again. Within 2 to 4 seconds after the SRS lights, reconnect the jumper to TC.

6. Within 2 to 4 seconds the SRS light will go off. One second later, if all DTCs are cleared the SRS light will flash steadily on and off. If codes are still registered it will flash in the pattern to indicate the stored codes.
Ok this is either impossible or I'm doing something wrong. It's really hard to read, interpret, and follow directions in 2-4 seconds. Also, the light is coming on solid immediately after disconnecting the jumper, not after 2-4 seconds so I'm not sure what's up there.

I thought I had it at first and was down to only code 32. Then I probed one of the weight sensors (still nothing!) and checked the codes again. Now I'm getting 32 and 55, but not 56. WTF?
MGarganoThread starterNJ · Aug 18, 2009#211
Originally Posted by CTScott ↑

2. When the SRS light starts flashing the codes, within 3 to 10 seconds remove the jumper from TC. After 3 seconds the SRS light will come on solid.
I'm getting stuck right at the beginning. The SRS light should come on solid after 3 seconds, but instead it comes on solid immediately after the jumper is disconnected.
CTScottUSA, CT · Aug 18, 2009#212
You might want to try two jumpers, where you can leave them on the pins and then connect them while your hands are up in visible range of the display.
MGarganoThread starterNJ · Aug 18, 2009#213
Originally Posted by CTScott ↑
You might want to try two jumpers, where you can leave them on the pins and then connect them while your hands are up in visible range of the display.
That's actually what I tried. I have one pin in each connector and am connecting the two with an alligator-clip wire but it's still tough. That aside, it doesn't seem to be going the way the directions indicate it should with the flashes, solids, etc.
MGarganoThread starterNJ · Aug 18, 2009#214
Ok, trying your idea I'm 99% I successfully cleared the codes. Well, codes 55 & 56 are gone, but code 32 remains flashing.
CTScottUSA, CT · Aug 18, 2009#215
Cool. At this point you must feel like your defusing a bomb.

Code 32 is the OCS. The issue right now is the lack of a base load on the sensors. They are calibrated for the weight of the empty seat.

Are you still measuring no voltage on the sensors?
MGarganoThread starterNJ · Aug 18, 2009#216
Originally Posted by CTScott ↑
Cool. At this point you must feel like your defusing a bomb.

Code 32 is the OCS. The issue right now is the lack of a base load on the sensors. They are calibrated for the weight of the empty seat.

Are you still measuring no voltage on the sensors?
I was measuring no voltage on the sensors with all the codes still flashing but I haven't tried it now with only code 32. Maybe they won't receive voltage if they don't sense any weight at all? The sensors are plugged into the system, but are just laying on the floor in the car.
CTScottUSA, CT · Aug 18, 2009#217
How about putting some pressure on each with a c-clamp or stacking them and using one clamp?
MGarganoThread starterNJ · Aug 18, 2009#218
Originally Posted by CTScott ↑
How about putting some pressure on each with a c-clamp or stacking them and using one clamp?
I'll try this tomorrow after work and report back
MGarganoThread starterNJ · Aug 19, 2009#219
Originally Posted by CTScott ↑
How about putting some pressure on each with a c-clamp or stacking them and using one clamp?
A preliminary run of this didn't seem to work but I only used one clamp per sensor. I'm also not sure which part is actually sensing the weight. Is it the four raised buttons on top?

Picture not included in this copy

Also, there is a threaded hole in the side of each bracket which goes through the black button in the right of this pic. It looks like the bolt goes through the button and touches the metal body of the sensor. I'm not sure if it's providing some kind of ground, etc.

Picture not included in this copy
CTScottUSA, CT · Aug 19, 2009#220
In the bottom pic, the flat area between those two buttons with the flexible flat cable coming off is the actual sensor. You need to put pressure on the plate below the buttons (which looks like it floats on the shafts below the buttons), without actually crunching the orange circuit board. You could cut a piece of wood or metal to just fit between the two buttons, and then clamp that against the plate below the circuit board.
MGarganoThread starterNJ · Aug 19, 2009#221
Ok I'll give that a try when I get home.
CTScottUSA, CT · Aug 19, 2009#222
When I have a chance later today I'll do some experimentation with the OCS on Crashy.

I replaced her popped airbags and pretensioners with resistors last night and reset the SRS ECU (It took me about 10 rounds to get it fully reset and I even rigged a momentary switch up to make it easier). She had more than 10 stored SRS DTC's.
MGarganoThread starterNJ · Aug 19, 2009#223
I'm glad to hear it wasn't just me having problems clearing the SRS codes!
CTScottUSA, CT · Aug 19, 2009#224
You really have to either memorize the pattern or have a second person there to read the instructions to you. I was monkeying with it at midnight, so I couldn't recruit one of my kids to help me.
MGarganoThread starterNJ · Aug 19, 2009#225
After about 20 attempts, I finally ended up just memorizing it. I was also getting thrown by the lack of a 3 second delay in the first step and the fact that it was close to 95 degrees while I was trying to do this. Extending the length of the jumper wires definitely helped though.
CTScottUSA, CT · Aug 19, 2009#226
OK. Now that the SRS is happy, I just did some experimentation with the OCS. The resistors will definitely not work, as there is a signal component as well from the sensor. There is a DC voltage, which is proportional to the weight applied to the sensor, but there is also an analog waveform on the signal pin. When I connected the resistors and power on the ignition, I would see the correct voltage on the signal pin for a couple of seconds, then the voltage would drop to zero and the passenger seat belt light would flash rapidly. Checking the DTC showed a 32. After disconnecting the battery and reconnecting the sensor, the DTC would go away and the OCS would operate normally. Tonight I am going to pull the sensors off of the seat, so I can experiment with one.
MGarganoThread starterNJ · Aug 19, 2009#227
Originally Posted by CTScott ↑
OK. Now that the SRS is happy, I just did some experimentation with the OCS. The resistors will definitely not work, as there is a signal component as well from the sensor. There is a DC voltage, which is proportional to the weight applied to the sensor, but there is also an analog waveform on the signal pin. When I connected the resistors and power on the ignition, I would see the correct voltage on the signal pin for a couple of seconds, then the voltage would drop to zero and the passenger seat belt light would flash rapidly. Checking the DTC showed a 32. After disconnecting the battery and reconnecting the sensor, the DTC would go away and the OCS would operate normally. Tonight I am going to pull the sensors off of the seat, so I can experiment with one.
I'm glad to hear, again, that it's not just me having problems with this. I look forward to hearing what you discover when you pull the sensors.
CTScottUSA, CT · Aug 19, 2009#228
I just took the seat apart (which turned out to be a challenge, as my largest torx bit is a T30). I realized that you can separate the seat base from the seat. Doing so provides a great way to mount an aftermarket seat to the four sensors. The silver bolts sticking out of the sensors are the mounting points. It seems like four heavy gauge L brackets or two 16" long pieces of angle iron are all that would be required.

Picture not included in this copy

1 attachment not included in this copy

MGarganoThread starterNJ · Aug 19, 2009#229
Mine looks the same... minus all the rust and that my sensors aren't bolted to the base anymore. But my passenger's seat is in two pieces like yours.
CTScottUSA, CT · Aug 19, 2009#230
Did you consider mounting your new seats to the base?

By the way, the carpet was completely saturated and the spare tire well was full to the top with water, hence the wicked rust.
MGarganoThread starterNJ · Aug 19, 2009#231
Originally Posted by CTScott ↑
Did you consider mounting your new seats to the base?
I honestly didn't think of it since the new seats came with Wedge brackets, which are much lower than the OEM base. I figured the two seats would be at different heights if I were to mount the passenger to the OEM bracket and keep the driver on the Wedge bracket. Plus, I'm not sure if the new seat bolts up to the OEM bracket.
CTScottUSA, CT · Aug 19, 2009#232
Originally Posted by MGargano ↑
I honestly didn't think of it since the new seats came with Wedge brackets, which are much lower than the OEM base. I figured the two seats would be at different heights if I were to mount the passenger to the OEM bracket and keep the driver on the Wedge bracket. Plus, I'm not sure if the new seat bolts up to the OEM bracket.

OK. Just a thought, while I was under there. I was thinking that if you mounted the passenger seat to the OEM base, that you would also mount the driver seat that way. I haven't pulled that one yet, but it looks like there's an equivalent height set of mounting points on that side.

Anyway, I removed the sensors. With them off of the base I am still seeing voltage on the sensor signal wires. The airbag off light was on. I clamped all four sensors with c clamps and now have the airbag on light.
MGarganoThread starterNJ · Aug 19, 2009#233
Originally Posted by CTScott ↑
OK. Just a thought, while I was under there. I was thinking that if you mounted the passenger seat to the OEM base, that you would also mount the driver seat that way. I haven't pulled that one yet, but it looks like there's an equivalent height set of mounting points on that side.

Anyway, I removed the sensors. With them off of the base I am still seeing voltage on the sensor signal wires. The airbag off light was on. I clamped all four sensors with c clamps and now have the airbag on light.
I forgot to mention that the new seats are attached to the base with torx bolts from the top (the same way the base is attached to the floor of the car), while the OEM seats attach to the brackets/sensors from the sides, so I think using the OEM brackets with these seats isn't an option for me.

Do you think there's something wrong with my sensors/system since I'm not seeing voltage on the signal wires? There is, of course, the possibility that I'm doing something wrong in testing for voltage, by the way 😆

Any chance you could post a pic of your clamp set up so I can duplicate? Also, did you have to reset the SRS codes in order for the airbag light to turn to 'on'? Or did it just change as soon as you clamped the sensors?
CTScottUSA, CT · Aug 19, 2009#234
I am measuring between the center wire (which is the signal output) and a chassis ground. I am using a needle probe, which is a very thin, sharp probe. With the waterproof connector, I am sticking it into the rubber seal around the wire.



Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

3 attachments not included in this copy

MGarganoThread starterNJ · Aug 19, 2009#235
Originally Posted by CTScott ↑
I am measuring between the center wire (which is the signal output) and a chassis ground. I am using a needle probe, which is a very thin, sharp probe. With the waterproof connector, I am sticking it into the rubber seal around the wire.
Ok, I'll definitely give this another try tomorrow. I don't have work so I should have plenty of time to mess around.

Out of curiosity, based on what you see so far, does it look possible to turn the airbag (and seat belt light/chime) on and off with a toggle switch? Or will we have to rig something using the OEM sensors?
CTScottUSA, CT · Aug 19, 2009#236
Originally Posted by MGargano ↑
Ok, I'll definitely give this another try tomorrow. I don't have work so I should have plenty of time to mess around.

Out of curiosity, based on what you see so far, does it look possible to turn the airbag (and seat belt light/chime) on and off with a toggle switch? Or will we have to rig something using the OEM sensors?
I'm not sure yet. Tomorrow morning I'll take a look at the signal output with an oscilloscope.
MGarganoThread starterNJ · Aug 20, 2009#237
I'm psyched. I have a feeling tomorrow's going to be a good day for this project.
1NZYaris1New Zealand · Aug 20, 2009#238
You Guy's deserve an award 👍 , soon we can all install sports seats 🤤
MGarganoThread starterNJ · Aug 20, 2009#239
I have all four sensors clamped like this:

Picture not included in this copy

Airbag 'Off' light and seat belt lights are still lit. Also not reading any voltage on the center wire.
CTScottUSA, CT · Aug 20, 2009#240
OK. With ignition power off, try reading resistance between the center wire and either of the outside wires. That will verify if you're actually making a good connection to the wire. You should see 48K ohms between the center and either outside wire.
MGarganoThread starterNJ · Aug 20, 2009#241
Ok. Should I keep the sensor clamped for this exercise? And I assume I'm changing the setting on the multimeter from VDC to ohms?
CTScottUSA, CT · Aug 20, 2009#242
Correct on VDC to ohms. Clamping is fine - It won't have any effect on the readings.
MGarganoThread starterNJ · Aug 20, 2009#243
Which setting am I putting the multimeter to?

Picture not included in this copy
Picture not included in this copy

I got a reading each time (center to left and center to right) with the black lead on center and the red on either outside wire but I have a feeling I have the meter on the wrong setting.
CTScottUSA, CT · Aug 20, 2009#244
Put the meter on 200K (always go to the next highest above what you are trying to see).
MGarganoThread starterNJ · Aug 20, 2009#245
Ok, with the meter on 200k, black lead in the center, red on either outside wire, I got 4.4 both times. I tried a few times and the numbers kept bouncing around some, but the most consistent (when I held my hands steady) was 4.4.
CTScottUSA, CT · Aug 20, 2009#246
OK. So right now your SRS light is off, air bag off is lit, and passenger seat belt is lit?

Try disconnecting the battery for 2 minutes, reconnecting and then measuring the voltage on the center pin to ground. for a really solid ground you might want to pop the passenger kick panel and touch the black lead to the ground bolt there.
MGarganoThread starterNJ · Aug 20, 2009#247
Originally Posted by CTScott ↑
OK. So right now your SRS light is off, air bag off is lit, and passenger seat belt is lit?
No, sir. All three lights, including the SRS, are still lit.
CTScottUSA, CT · Aug 20, 2009#248
With the SRS, are you still seeing the DTC 32?
MGarganoThread starterNJ · Aug 20, 2009#249
I just checked it. I now have 32, 55, & 56 again.
CTScottUSA, CT · Aug 20, 2009#250
You might want to check your resistors. I had trouble with mine not making great contact. I ended up shoving mine in through the wire side so they would fit tighter.