The sensors are attached to the rail with a torx screw from the outside, or so it seems
Looking at seats...
318 posts · 113,151 views · page 2 of 7
Replies continued
It looks like you'd have to physically remove the seat from the frame to get to at least one of these screws
By meatal shield, I meant this guy (with the 060). The sensor is behind him:
Picture not included in this copy
Picture not included in this copy
I can't wait to see them installed
These two torx screws hold the right rear sensor to the rail, but that silver arm is in the way. Also, the other 3 torx screws are covered by the body of seat, so I can't see a way to take them out.
Picture not included in this copy
Picture not included in this copy
My bad. How's this?Originally Posted by CTScott ↑By meatal shield, I meant this guy (with the 060). The sensor is behind him:
Picture not included in this copy
Picture not included in this copy
Much better...
That makes two of us! 😆Originally Posted by lilredrocket ↑I can't wait to see them installed
If I end up picking up the wrecked eBay Yaris, I'll have a set of seats to mess with the sensors. They appear to be resistive load cells.
Is there enough space under the new seat for the Occupant Classification ECU?
Is there enough space under the new seat for the Occupant Classification ECU?
Is that this guy?
Picture not included in this copy
Picture not included in this copy
Yes. He'll need to still be connected.
Not really any room under the seat or on the brackets:
Picture not included in this copy
Picture not included in this copy
Is it safe to just lay it on the floor under the seat?
Scratch that... I can attach it to the front of the bracket
How about the seat belts - Are you going to use the exiting or replace them with harnesses?
Booya!
Picture not included in this copy
Picture not included in this copy
I'm using the existing belts. I already removed the seat belts from the old seats and bolted them to the new ones.Originally Posted by CTScott ↑How about the seat belts - Are you going to use the exiting or replace them with harnesses?
Apparently the driver's side seat belt is not the same as the passenger's side. Driver's side is plugged into this:
Picture not included in this copy
Picture not included in this copy
No idea what this is, but it's magnetic... stuck to the rail when I removed the torx screw holding it in.
I attached it to the driver's side bracket. Seat belts officially swapped!
*patiently awaits the next step*
Ok, I plugged the 3.3 ohm resistors into the airbag sensors and installed 10k ohm resistors between Pin 1 (SVC) and Pin 2 (SIG) and 470 ohm resistor between Pins 2 & 3...
I'm getting the SRS warning light in the instrument cluster, Passenger Airbag 'Off' and passenger seat belt light blinking....
I'm getting the SRS warning light in the instrument cluster, Passenger Airbag 'Off' and passenger seat belt light blinking....
...so now I'm totally lost. Help!
Did you disconnect the battery while you were unplugging the airbag, etc? If not, disconnect it for a couple of minutes and then reconnect it to reset the SRS ECU.
Yes, I disconnected the battery before I did anything.Originally Posted by CTScott ↑Did you disconnect the battery while you were unplugging the airbag, etc? If not, disconnect it for a couple of minutes and then reconnect it to reset the SRS ECU.
The only thing that seems to be working correctly is the driver's side seat belt. Driver's SRS light is on, passenger's side seat belt is blinking whether the belt is inserted or not, and the passenger's airbag light says 'off'
OK. We can find out why SRS isn't happy by jumpering CG to TC on the OBDII connector, and then turning the ignition to the on position. After about 60 seconds the SRS will flash in a pattern. The codes are two digits and multiple ones may be shown.Originally Posted by MGargano ↑The only thing that seems to be working correctly is the driver's side seat belt. Driver's SRS light is on, passenger's side seat belt is blinking whether the belt is inserted or not, and the passenger's airbag light says 'off'
For example, a 31 will be: flash, flash, flash, pause, flash, long pause
There will be a 2.5 second pause in between each, and then a 4 second pause before the pattern repeats.
Here are the pins to jump on the OBD connector:
Picture not included in this copy
1 attachment not included in this copy
Ok looks like possibly 32 (flash flash flash pause flash flash), 55, & 56... Hope that makes some sense
32 is Occupant Classification System Malfunction
55 is Driver side squib circuit issue
56 is Passenger side squib circuit issue
After you shut off the ignition and removed the jumper the DTC's may have been cleared. With the jumper removed, turn the ignition back to on and see if the SRS light is still on.
With the seat belt, did you reconnect the 4 position connector that was next to the airbag connector?
55 is Driver side squib circuit issue
56 is Passenger side squib circuit issue
After you shut off the ignition and removed the jumper the DTC's may have been cleared. With the jumper removed, turn the ignition back to on and see if the SRS light is still on.
With the seat belt, did you reconnect the 4 position connector that was next to the airbag connector?
All lights are still lit after removing the jumper. And yes, the only things not connected are the 4 weight sensors.Originally Posted by CTScott ↑32 is Occupant Classification System Malfunction
55 is Driver side squib circuit issue
56 is Passenger side squib circuit issue
After you shut off the ignition and removed the jumper the DTC's may have been cleared. With the jumper removed, turn the ignition back to on and see if the SRS light is still on.
With the seat belt, did you reconnect the 4 position connector that was next to the airbag connector?
OK. Can you either measure one of the 3 ohm resistors with an ohm meter, or just give me the colors of the stripes to make sure that they are correct?
How's this?
Picture not included in this copy
Picture not included in this copy
I pushed one end of the wire into each of the pins of the yellow SRS connector, with the resistor in the middle
OK. There's one problem. That resistor is not 3 ohms, it's 3.3 Mega Ohms (which looks like an open circuit). A 3 ohm resistor will be: orange, black, gold, silver or gold
Picture not included in this copy
Picture not included in this copy
Goddamn it! I swear you can't trust anyone these days! The store I got them from sold them loose, not in a package, so I took their word that they were 3 ohms. I even specified not 3k or 3m!
Well at least that's one problem solved! 😆
Well at least that's one problem solved! 😆
Yeah, that will fix codes 55 and 56.
For the 32, do you have enough 10K resistors (4 more) to replace the 470's with 10K's? That would move us to the middle of the sensor range, instead of off to one end, like we currently have it.
For the 32, do you have enough 10K resistors (4 more) to replace the 470's with 10K's? That would move us to the middle of the sensor range, instead of off to one end, like we currently have it.
I don't have more, but they're easily available at the Crap Shack. You want me to replace all the resistors in the pressure sensor pins with 10k? So a total of 8 10k's and no 470's?Originally Posted by CTScott ↑Yeah, that will fix codes 55 and 56.
For the 32, do you have enough 10K resistors (4 more) to replace the 470's with 10K's? That would move us to the middle of the sensor range, instead of off to one end, like we currently have it.
I was going to have you try that if you had them laying around. Let me go probe my still-installed sensors and I'll give you a better answer...Originally Posted by MGargano ↑I don't have more, but they're easily available at the Crap Shack. You want me to replace all the resistors in the pressure sensor pins with 10k? So a total of 8 10k's and no 470's?
Ok, sounds good. I won't be able to fool around with this again until Sunday anyway.Originally Posted by CTScott ↑I was going to have you try that if you had them laying around. Let me go probe my still-installed sensors and I'll give you a better answer...
BTW- Through all this I totally forgot to ask- what is the expected outcome? Will I have OEM airbag function (minus, obviously, the side airbags in the old seats)?
OK. I just probed mine - I see 3.94 volts on each of the SIG lines with the seat empty, ~4.00 volts with me sitting on the seat (and I weigh about 155 lbs), and ~4.20 volts when I put all of my weight on the corner being measured.
Based on that we should flip your 10K and 470 ohm resistors to make the passenger airbag active. To make it inactive, we are probably looking at increasing the 470 ohm to about 2.5K to 3K.
When you have a chance, measure the voltage of one of your connectors from pin 2 to pin 3 for me. Also measure Pin 1 to Pin 3.
Based on that we should flip your 10K and 470 ohm resistors to make the passenger airbag active. To make it inactive, we are probably looking at increasing the 470 ohm to about 2.5K to 3K.
When you have a chance, measure the voltage of one of your connectors from pin 2 to pin 3 for me. Also measure Pin 1 to Pin 3.
Ok, so I should run 10k from 1-2 and 470 from 2-3? That should keep the passenger's airbag active all the time?Originally Posted by CTScott ↑
Based on that we should flip your 10K and 470 ohm resistors to make the passenger airbag active. To make it inactive, we are probably looking at increasing the 470 ohm to about 2.5K to 3K.
When you have a chance, measure the voltage of one of your connectors from pin 2 to pin 3 for me. Also measure Pin 1 to Pin 3.
Oops... I meant I should change it to 470 from 1-2 and 10k from 2-3, right? I currently have it set with 10k from 1-2 and 470 from 2-3
Correct 10K 2-3 and 470 1-2 for airbag always active.
Ok, I'll try to do this tomorrow before work and let you know. If all goes well, the passenger's airbag light should say 'on' and the passenger's seat belt light will turn off when belted, right?Originally Posted by CTScott ↑Correct 10K 2-3 and 470 1-2 for airbag always active.
I believe so.Originally Posted by MGargano ↑Ok, I'll try to do this tomorrow before work and let you know. If all goes well, the passenger's airbag light should say 'on' and the passenger's seat belt light will turn off when belted, right?
Fingers crossed!
How's this look?
Picture not included in this copy
I couldn't wait until tomorrow or Sunday 😆
Picture not included in this copy
I couldn't wait until tomorrow or Sunday 😆
Picture not included in this copy
Picture not included in this copy