Yarisworld Archive

Looking at seats...

318 posts · 113,151 views · page 3 of 7

Replies continued

MGarganoThread starterNJ · Aug 8, 2009#101
Originally Posted by CTScott ↑
Correct 10K 2-3 and 470 1-2 for airbag always active.
No change in any of the indicators after swapping these, but maybe it's because of the missing/wrong resistors in the airbag sensors?
CTScottUSA, CT · Aug 8, 2009#102
Did you by any chance measure the voltage between 2 and 3 and 1 and 3?
MGarganoThread starterNJ · Aug 8, 2009#103
Originally Posted by CTScott ↑
Did you by any chance measure the voltage between 2 and 3 and 1 and 3?
I'm sure I have the required tools for this, but how would I go about doing this?
cali yarisCanoga Park, CA · Aug 8, 2009#104
this is a really good read. Guys when it's all done, can it be compressed and posted as a DIY? I know a lot of people who would like to know how to do this!
jonismynameadirondacks, ny · Aug 8, 2009#105
you guys are no joke. if co-workers and married couples could co-operate as well in the same room as you guys are over a forum the world would be a very different place... rock on.
CTScottUSA, CT · Aug 8, 2009#106
We'll definitely turn this into a DIY once we figure it all out.

As far as clearing the current stored codes, Let's try a couple minute battery disconnect. The SRS system supposedly clears most types of stored codes if it is off for a while. If that doesn't work, we can manually clear them via that same jumper we used to make it flash the light patterns. The process for clearing them that way is a bit convoluted, so hopefully the power down will do the trick.
MGarganoThread starterNJ · Aug 8, 2009#107
Originally Posted by CTScott ↑
We'll definitely turn this into a DIY once we figure it all out.

As far as clearing the current stored codes, Let's try a couple minute battery disconnect. The SRS system supposedly clears most types of stored codes if it is off for a while. If that doesn't work, we can manually clear them via that same jumper we used to make it flash the light patterns. The process for clearing them that way is a bit convoluted, so hopefully the power down will do the trick.
I'm guessing I should wait until I install the correct 3 ohm resistors in the SRS senors before disconnecting the battery? Otherwise we'll still have the same problem right?
CTScottUSA, CT · Aug 8, 2009#108
You could try it as-is to see if we clear the code 32 and have the passenger air bag on light.
MGarganoThread starterNJ · Aug 8, 2009#109
Originally Posted by CTScott ↑
You could try it as-is to see if we clear the code 32 and have the passenger air bag on light.
Roger that. How long should I leave the battery disconnected?
CTScottUSA, CT · Aug 8, 2009#110
Originally Posted by MGargano ↑
Roger that. How long should I leave the battery disconnected?
5 minutes should be enough.
MGarganoThread starterNJ · Aug 8, 2009#111
Originally Posted by CTScott ↑
5 minutes should be enough.
Should I jump the OBDII ports again? Or just turn the ignition to 'on' and check the indicators?
CTScottUSA, CT · Aug 8, 2009#112
Originally Posted by MGargano ↑
Should I jump the OBDII ports again? Or just turn the ignition to 'on' and check the indicators?
Power it up once to see, and then power off, jump and read the flashes. Now hopefully just codes 55 and 56 come up.
MGarganoThread starterNJ · Aug 8, 2009#113
No good. SRS, passenger airbag 'off', and passenger seat belt indicators still lit. The jump showed the same 32, 55, & 56 codes
CTScottUSA, CT · Aug 8, 2009#114
Originally Posted by MGargano ↑
No good. SRS, passenger airbag 'off', and passenger seat belt indicators still lit. The jump showed the same 32, 55, & 56 codes
OK. Do you have a multimeter to measure the voltage?
MGarganoThread starterNJ · Aug 8, 2009#115
Rock n' Roll

Picture not included in this copy
MGarganoThread starterNJ · Aug 8, 2009#116
Just tell me what I'm doing here... it's been forever since I've used this thing lol
CTScottUSA, CT · Aug 8, 2009#117
Probes are in the right hole. Switch it to VDC 20. Touch the black lead to pin 3 and the red to 1 and then 3.
MGarganoThread starterNJ · Aug 8, 2009#118
Originally Posted by CTScott ↑
Probes are in the right hole. Switch it to VDC 20. Touch the black lead to pin 3 and the red to 1 and then 3.
Roger. We're talking about one of the four weight sensors, right?
CTScottUSA, CT · Aug 8, 2009#119
Originally Posted by MGargano ↑
Roger. We're talking about one of the four weight sensors, right?
Correct
MGarganoThread starterNJ · Aug 8, 2009#120
Ok with the meter on VDC 20 I'm getting zero on everything. WTF?
CTScottUSA, CT · Aug 8, 2009#121
You have to have the ignition on.
MGarganoThread starterNJ · Aug 8, 2009#122
The ignition is on, for the record
MGarganoThread starterNJ · Aug 8, 2009#123
I just tried a different sensor, still nothing...
CTScottUSA, CT · Aug 8, 2009#124
Hmmm. Measure the voltage between the battery posts to make sure the meter is working.
MGarganoThread starterNJ · Aug 8, 2009#125
Originally Posted by CTScott ↑
Hmmm. Measure the voltage between the battery posts to make sure the meter is working.
That's working. Meter measure 12.55 or so volts
CTScottUSA, CT · Aug 8, 2009#126
OK. Check the ECU-B fuse under the hood.
MGarganoThread starterNJ · Aug 8, 2009#127
Originally Posted by CTScott ↑
OK. Check the ECU-B fuse under the hood.
Fuse is intact
MGarganoThread starterNJ · Aug 8, 2009#128
Is it possible to resume this tomorrow? My car's in the driveway and it's starting to rain. Plus it's getting kinda late. I have all day tomorrow, if you're game and available?
CTScottUSA, CT · Aug 8, 2009#129
No problem.
CTScottUSA, CT · Aug 9, 2009#130
Picture not included in this copy

The first thing to check, when you have a chance today is a couple of voltage readings on the Occupant Classification ECU cable harness.

If you look at the image above J24 has the Black connector going to it and U1 has the Gray connector.

Pull the J24 Black connector and then measure the following (on the cable connector side):

Put the black lead on pin 3 and the red one on the wire being checked.

Pin 1 (Violet wire) to Pin 3 (White wire with black stripe)

Pin 7 (Beige wire) to Pin 3 (White wire with black stripe)

1 attachment not included in this copy

MGarganoThread starterNJ · Aug 9, 2009#131
Pin 1-3: looks like .14
Pin 3-7: looks like .12/.13
MGarganoThread starterNJ · Aug 9, 2009#132
And, of course, as soon as I get outside, it starts pouring rain. I'd continue, but I have to keep getting out of the car so I can move closer to my house where my iPod Touch can pickup an internet signal to keep refreshing the forum for directions 😆
CTScottUSA, CT · Aug 9, 2009#133
Originally Posted by MGargano ↑
Pin 1-3: looks like .14
Pin 3-7: looks like .12/.13
Nothing like working in the rain.

Are those readings with the ignition on or off?

It should be on for the readings. 7-3 should be 12V with the key on or off. 1-3 should be 12V only with the key on.

Also, with your meter, when I had you check the meter by measuring the battery voltage last night, did you see 14., as opposed to the .14 that you just read on 1-3?
MGarganoThread starterNJ · Aug 9, 2009#134
Originally Posted by CTScott ↑
Nothing like working in the rain.

Are those readings with the ignition on or off?

It should be on for the readings. 7-3 should be 12V with the key on or off. 1-3 should be 12V only with the key on.

Also, with your meter, when I had you check the meter by measuring the battery voltage last night, did you see 14., as opposed to the .14 that you just read on 1-3?
Ok it's all good now. Your diagram's pin numbers didn't match up with my connector but I was able to figure it out based on the colors. I have 12V all around now.

My connector seems to be labeled left to right, whereas as yours is right to left
MGarganoThread starterNJ · Aug 9, 2009#135
Scratch that...I'm retarded. Your pic is of the ECU, not the connector. It's all good now.
CTScottUSA, CT · Aug 9, 2009#136
Originally Posted by MGargano ↑
Scratch that...I'm retarded. Your pic is of the ECU, not the connector. It's all good now.
That gets confusing. Sometimes the pics are of the cable side, sometimes of the device side.

OK. So both power feeds into the module are fine. Try removing the resistors and then reading the 1-3 and 2-3 voltages on the sensor connectors.
cali yarisCanoga Park, CA · Aug 9, 2009#137
I am totally subscribed to this. Mgargano and CTScott, BIG props to both of you for having this conversation on a thread. 🙇 🙇 🙇
MGarganoThread starterNJ · Aug 9, 2009#138
Originally Posted by CTScott ↑
That gets confusing. Sometimes the pics are of the cable side, sometimes of the device side.

OK. So both power feeds into the module are fine. Try removing the resistors and then reading the 1-3 and 2-3 voltages on the sensor connectors.
Which pins get which leads?
CTScottUSA, CT · Aug 9, 2009#139
Originally Posted by MGargano ↑
Which pins get which leads?
black on 3, red on 1 then 2
MGarganoThread starterNJ · Aug 9, 2009#140
Ignition on, J24 plugged back into the OC-ECU, resistors on the 4 weights sensors removed and....

Nothing. Zeros on all four sensors for 1-3 and 2-3
CTScottUSA, CT · Aug 9, 2009#141
And, U1 (the gray connector) is plugged in?
MGarganoThread starterNJ · Aug 9, 2009#142
Originally Posted by CTScott ↑
And, U1 (the gray connector) is plugged in?
Yes
CTScottUSA, CT · Aug 9, 2009#143
OK. Try measuring each of the three pins relative to chassis ground (a seat mounting bolt would be fine). Red on 1, 2, and then 3 and black to the bolt.
MGarganoThread starterNJ · Aug 9, 2009#144
Originally Posted by CTScott ↑
OK. Try measuring each of the three pins relative to chassis ground (a seat mounting bolt would be fine). Red on 1, 2, and then 3 and black to the bolt.
Still nothing...all zeros
CTScottUSA, CT · Aug 9, 2009#145
Hmmmm. Can you remove one of the sensors from the OEM seat and plug it in, so we can take some readings with it attached?
MGarganoThread starterNJ · Aug 9, 2009#146
Originally Posted by CTScott ↑
Hmmmm. Can you remove one of the sensors from the OEM seat and plug it in, so we can take some readings with it attached?
It'll definitely be a challenge, but I will certainly try
MGarganoThread starterNJ · Aug 9, 2009#147
Pardon the language, but....

Boo-fucking-ya!

Picture not included in this copy
MGarganoThread starterNJ · Aug 9, 2009#148
CTScott... fellow forum members... meet the left rear passenger's weight sensor.
MGarganoThread starterNJ · Aug 9, 2009#149
...and his friend, the left front passenger's weight senor...

Picture not included in this copy
CTScottUSA, CT · Aug 9, 2009#150
Nice. Now the tricky part is to get the meter on with them connected. To do so, I take a sewing pin or needle and shove it into the soft rubber where the wire enters the connector. We should only need one, as we can take the measurements to ground.