Yarisworld Archive

Looking at seats...

318 posts · 113,151 views · page 1 of 7

MGarganoOriginal postNJ · Jul 30, 2009#1
I'm looking to upgrade the front seats in my 09' hatch but I'm honestly not really sure what's out there, especially since some of the websites I checked out are crazy expensive. I'm just looking for something with good support, OEM function (sliding, reclining front and back, folding to let passenger's in back), and something lower to the ground.

I see these on fleaBay, but I'm not sure of the quality or fitment: http://cgi.ebay.com/ebaymotors/MAZDA...Q5fAccessories

Appreciate any help I can get with this.

Replies 317

1NZYaris1New Zealand · Jul 30, 2009#2
They look good , but the real test is how hard or soft they are ,
which you won't know until you have them .
for $200. i would buy them . my 2 cents worth. 👍
TinyGiantRochester, NH · Jul 30, 2009#3
i've been wondering if someleather seats from maybe the camry would fit.. i wish there was a good junk yard around here.. i
cruz-gsrAshland Mass · Jul 30, 2009#5
i got a set of red tenzo r use but in mint condition ill let them.
1NZYaris1New Zealand · Jul 30, 2009#6
Originally Posted by MGargano ↑
They look almost like the ones we get over here ,
Nice seat ,good quality, but the wife hated the harshness of the seat,
not soft enough for here tosh.😆
ethelitershouston · Jul 31, 2009#7
any pics of the tenzo r's cruz?
MGarganoThread starterNJ · Jul 31, 2009#8
Can anyone confirm if the Evo VIII Recaro seats fit in the Yaris?
mrbondIllinois · Jul 31, 2009#10
They're real Brides, but from Bride of Thailand, so not authentic.
MGarganoThread starterNJ · Aug 2, 2009#11
I did a quick search and didn't come up with anything...

Has anyone solved the passenger's side ABS/seat belt light problem when swapping OEM seats? I ordered these from Garm and I'm curious how to go about installing them

http://www.microimageonline.com/foru...?p=175#post175
botchilahPhilippines · Aug 3, 2009#12
Not to sound like a snob but I'd stay away from generic / fake / replica "sport" seats. I've seen a good number of these seats (usually made in Thailand) tested from a RECARO PR video (well I guess the video was biased lol) and the seats usually break in half at the seatback when subjected to a typical collission test. The OEM seats go through a lot of rigorous testing so even if they LOOK flimsy and offer little suport, the OEM seats are far safer than these replica / fake seats.

AFAIK almost any RECARO seat (so yes the OEM Evo RECARO seats should fit) will fit into the Yaris BUT with the proper bolt-on seat frame rails. RECARO makes them but they are very expensive, like 500 U$D each since these are usually made in Japan. I have a pair that's waiting to be picked up by me from by friend who is the RECARO distributor. IMO unless you're bolting a fixed bucket seat onto the Yaris' flooring directly, get a proper seat frame rail from companies like Wedge Engineering (much cheaper than the OEM RECARO seat rails). It's a bolt-on affair, it won't move around and will stay firmly in place when you corner hard around the track / auto-x and in the event of an accident.

It's a safety thing, like good tires, good wheels and good brake pads IMHO.
CTScottUSA, CT · Aug 3, 2009#13
Originally Posted by MGargano ↑
I did a quick search and didn't come up with anything...

Has anyone solved the passenger's side ABS/seat belt light problem when swapping OEM seats? I ordered these from Garm and I'm curious how to go about installing them

http://www.microimageonline.com/foru...?p=175#post175
There are two threads that I've noticed on this:

In this one JM350 successfully transferred the sensors to new seats:
New seats and how i did it !!!!

In this one at the end I documented a method, which I believe will work for bypassing the sensors. I don't believe that anyone has tried it yet:
Finally...Bride Racing Seat Installed
cali yarisCanoga Park, CA · Aug 3, 2009#14
How can I tell if they're real Bride's? They say 'not made in Japan'
'

If they are not made in Japan, they are not BRIDE seats. I know the maker of the Thai version, and it is not a licensed copy, it's just a copy.
MGarganoThread starterNJ · Aug 4, 2009#15
Will I have any problems swapping the 09 seats? From what I read upon searching, these seats have airbag compartments built into them? Does that throw a wrench in the works in terms of changing them?
CTScottUSA, CT · Aug 4, 2009#16
Since you won't be transferring the side airbags to the new seats, you'll need to install a 3 ohm resistor across the connector (in place of the airbag) to keep the system happy.
MGarganoThread starterNJ · Aug 4, 2009#17
Originally Posted by CTScott ↑
Since you won't be transferring the side airbags to the new seats, you'll need to install a 3 ohm resistor across the connector (in place of the airbag) to keep the system happy.
I haven't really looked at any of the wiring to see what's involved, so I'm not sure which connector you mean. Are there any other surprises I can expect with this swap?
CTScottUSA, CT · Aug 4, 2009#18
Originally Posted by MGargano ↑
I haven't really looked at any of the wiring to see what's involved, so I'm not sure which connector you mean. Are there any other surprises I can expect with this swap?
It's a two pin yellow connector (under the seat) for the side airbag squib. The 3 ohm resistor trick is the same thing that is done to eliminate the steering wheel airbag, when swapping steering wheels. It fools the SRS into thinking that the airbag is still present.

I am sure there will be a few surprises, but I don't think that you'll run into anything insurmountable.
MGarganoThread starterNJ · Aug 4, 2009#19
Originally Posted by CTScott ↑
It's a two pin yellow connector (under the seat) for the side airbag squib. The 3 ohm resistor trick is the same thing that is done to eliminate the steering wheel airbag, when swapping steering wheels. It fools the SRS into thinking that the airbag is still present.

I am sure there will be a few surprises, but I don't think that you'll run into anything insurmountable.
So it's as straight-forward as it sounds? Just plug the resistor into the two pins in the connector and voila?
CTScottUSA, CT · Aug 4, 2009#20
Originally Posted by MGargano ↑
So it's as straight-forward as it sounds? Just plug the resistor into the two pins in the connector and voila?
Yes - Plug it in, and tape or heat shrink it.
MGarganoThread starterNJ · Aug 4, 2009#21
Originally Posted by CTScott ↑
Yes - Plug it in, and tape or heat shrink it.
Ok so of course my local Radio Shack doesn't have 3 ohm resistors. Will a 3.3k ohm resistor work? Are they they same? Some had a 'k' and some had an 'm' and some just said 'ohms'
kngrsllSpartanburg, SC · Aug 4, 2009#22
i have a set of weapon R seat brackets that i didnt end up using... I will sell them cheap.

maybe that will help the OP? :dunno:
CTScottUSA, CT · Aug 4, 2009#23
Originally Posted by MGargano ↑
Ok so of course my local Radio Shack doesn't have 3 ohm resistors. Will a 3.3k ohm resistor work? Are they they same? Some had a 'k' and some had an 'm' and some just said 'ohms'
You want just ohms (k=1000's, M=millions). 3.3 ohms would be fine, but not 3.3 K or 3.3 M. The resistors should be 1/2 watt rated ones as well (they come in 1/8, 1/4, 1/2, etc).
MGarganoThread starterNJ · Aug 4, 2009#24
Originally Posted by kngrsll ↑
i have a set of weapon R seat brackets that i didnt end up using... I will sell them cheap.

maybe that will help the OP? :dunno:
Thanks, but I found seats and Wedge brackets from Garm already
MGarganoThread starterNJ · Aug 4, 2009#25
Originally Posted by CTScott ↑
You want just ohms (k=1000's, M=millions). 3.3 ohms would be fine, but not 3.3 K or 3.3 M. The resistors should be 1/2 watt rated ones as well (they come in 1/8, 1/4, 1/2, etc).
If their website is any indicator, it looks like Radio Shack doesn't carry these at all. Looks like I've got some hunting to do, unless I want to order them online and pay $hipping. Thanks for the info though!
CTScottUSA, CT · Aug 5, 2009#26
I looked through my stash of resistors and found a bag of a couple hundred 2.5 ohm resistors. These would be fine, as anything in the range from about 2 ohms to 4 ohms will work.

Send me a PM with your mailing address and I'll put a bunch in an envelope and drop them in the mail...
MGarganoThread starterNJ · Aug 5, 2009#27
Originally Posted by CTScott ↑
I looked through my stash of resistors and found a bag of a couple hundred 2.5 ohm resistors. These would be fine, as anything in the range from about 2 ohms to 4 ohms will work.

Send me a PM with your mailing address and I'll put a bunch in an envelope and drop them in the mail...
Thanks for the offer, but I think I'm set. I found a local mom & pop-type electronics store that had 3.3 ohm 1/2 watt resistors, so I should be good for now. Thanks again!
CTScottUSA, CT · Aug 5, 2009#28
Originally Posted by MGargano ↑
Thanks for the offer, but I think I'm set. I found a local mom & pop-type electronics store that had 3.3 ohm 1/2 watt resistors, so I should be good for now. Thanks again!

Excellent! That's a good find. Radio Shack is becoming more and more of a cell phone hut and less and less of an electronics place.
MGarganoThread starterNJ · Aug 5, 2009#29
Originally Posted by CTScott ↑
Excellent! That's a good find. Radio Shack is becoming more and more of a cell phone hut and less and less of an electronics place.
I try to avoid that place at all costs. They never have what I'm looking for and their 'help' is the least knowledgeable I've seen. They sounded like they'd never heard the word 'resistor' when I called asking for one. 👎
cali yarisCanoga Park, CA · Aug 5, 2009#30
^ They probably thought it was a political thing.
lilredrocketDFW, Texas · Aug 5, 2009#31
^Haha!!
MGarganoThread starterNJ · Aug 5, 2009#32
It looks like, with these resistors, I'll be all set with the driver's seat. But I have a feeling I'm going to run into problems with the passenger's seat.

Originally Posted by CTScott ↑
In this one JM350 successfully transferred the sensors to new seats:
New seats and how i did it !!!!
Those 4 pressure senors seem like they're no joke and the only thread on here to detail a successful swap (^^^ )no longer has any pics to show the process, so I'm screwed there.


Originally Posted by CTScott ↑
In this one at the end I documented a method, which I believe will work for bypassing the sensors. I don't believe that anyone has tried it yet:
Finally...Bride Racing Seat Installed
I'd gladly be a guinea pig to try CTScott's idea of tricking the Occupant Classification ECU but, after reading his post, I'd definitely need help figuring out the electrical
CTScottUSA, CT · Aug 5, 2009#33
First off, pick up the resistors. 470 ohm and 10 K ohm (four of each). They don't need t be 1/2 Watt, so you can go with 1/4 or 1/8 Watt (whatever you can find in stock).
MGarganoThread starterNJ · Aug 6, 2009#34
Originally Posted by CTScott ↑
First off, pick up the resistors. 470 ohm and 10 K ohm (four of each). They don't need to be 1/2 Watt, so you can go with 1/4 or 1/8 Watt (whatever you can find in stock).
Picked up the resistors today, 1/4 watt. I'll let you know when I get the seats and I guess we can proceed to the next step
vtencolumbus · Aug 6, 2009#35
sorry for the thread hijack ...

but I found no yellow connector under my passanger seat.... there's 3 connector underneath the seat ... 2 are connected side by side and the other single one is wrapped with a plastic cable shielding ....

so which one to plug the resistor at ?

thank you ...and sorry again for the thread hijack ...
CTScottUSA, CT · Aug 6, 2009#36
Originally Posted by vten ↑
sorry for the thread hijack ...

but I found no yellow connector under my passanger seat.... there's 3 connector underneath the seat ... 2 are connected side by side and the other single one is wrapped with a plastic cable shielding ....

so which one to plug the resistor at ?

thank you ...and sorry again for the thread hijack ...
Does your car have the side airbags (and the SRS tag hanging off of the side of the seat)? If not, then you won't find the yellow connector under the seat for the airbag. Under the center of the passenger seat is the Occupant Classification ECU. It has two 12 pin connectors attached (one gray and one black). If you have the side airbag, then the yellow connector for it, is right next to the OC ECU.
vtencolumbus · Aug 6, 2009#37
no side airbags....

so is the resistor method works on the non side airbags yaris ? and how ?

thank you
CTScottUSA, CT · Aug 6, 2009#38
There are two different purposes to the resistors:

The 3 ohm ones are used to fool the Center Airbag Sensor Assembly into thinking that the side airbags are still present.

The 10K and 470 ohm resistors are to fool the Occupant Classification ECU into thinking that the four passenger seat Occupant Classification Sensors are present and are indicating that the seat is empty or has an adult sitting there.

This thread shows the idea behind the OCS bypass:
Finally...Bride Racing Seat Installed
MGarganoThread starterNJ · Aug 7, 2009#39
Seats are here! Let the games begin!
CTScottUSA, CT · Aug 7, 2009#40
Originally Posted by MGargano ↑
Seats are here! Let the games begin!
1st Play - Remove the passenger seat.

Leave the Occupant classification ECU connected. Disconnect the four occupant classification sensors (on the four corners of the seat). Disconnect the side airbag (yellow connector next to the OC ECU).

When you get the seat out, take some pictures of the bottom of the seat, specifically of the sensors and how they are mounted.
MGarganoThread starterNJ · Aug 7, 2009#41
Picture not included in this copy
MGarganoThread starterNJ · Aug 7, 2009#42
Picture not included in this copy
MGarganoThread starterNJ · Aug 7, 2009#43
Picture not included in this copy
MGarganoThread starterNJ · Aug 7, 2009#44
Picture not included in this copy
MGarganoThread starterNJ · Aug 7, 2009#45
Picture not included in this copy
MGarganoThread starterNJ · Aug 7, 2009#46
This is where I'm at so far
CTScottUSA, CT · Aug 7, 2009#47
Very good. I would like to see behind the metal shield, if you can get that angle. I want to see how the sensors are mounted between the seat and the rail. (just brainstorming on how to keep the sensors, like the person in the other post did).
MGarganoThread starterNJ · Aug 7, 2009#48
Looks like the metal shield is welded in place...
MGarganoThread starterNJ · Aug 7, 2009#49
Picture not included in this copy
MGarganoThread starterNJ · Aug 7, 2009#50
Picture not included in this copy