Yarisworld Archive

Micro Image Intake Manifold thread

467 posts · 153,219 views · page 8 of 10

Replies continued

tooterLos Angeles · Feb 16, 2013#351
Originally Posted by 4/20 NEVER FORGET ↑
As for the throttle body, based on what I read on here, I did not do a chip swap. My part number is ending in 030. After driving it around for a couple hours tonight, I think I am going to have to do a chip swap. On initial start up the idle would not stabilize, it would climb in RPMs then drop quickly, then climb and drop over and over until shut off. I remember tooter saying to back the screw out a turn so I did so and the idle stabilized but was still very high. After backing it out further I was able to get the idle to stabilize.

My guess is I need to do a chip swap. The car doesn't drive perfect. When I am coasting off of the throttle, say at 30mph (or any mph, doesn't matter), it doesn't matter if I barely touch the throttle or hammer the throttle, the car has a tiny "hiccup" feeling, as if the throttle was partly open then it closed and then opened. It's hard to describe. Also, when I am at partial throttle and I let off the throttle, it hangs for a second or two before closing and starting to decelerate. Is that normal? I know the car did it before, but it is far more pronounced now.

I also had some problems with high idle and idle hang, but I found that adjusting the throttle screw to a higher rpm idle has fixed it. I'm idling pretty high right now, probably around 1000-1200 rpm, but I haven't gotten a check engine light since I adjusted it this way (maybe 10 miles worth of driving where it would happen immediately before) so I think I am just going to leave it for now.

What do you guys think? I thought I had the right throttle body part number, but I'm thinking a chip swap is in my future.
Did you try backing out this idle screw about one turn counterclockwise? (it's the small screw at the top center of the picture just under the black plastic chip...)

Picture not included in this copy


That should solve all of the problems you just described. Mine exactly the same symptoms, and they all disappeared once the idle speed was reduced.
4/20 NEVER FORGETPortland, OR · Feb 17, 2013#352
Originally Posted by tooter ↑
Did you try backing out this idle screw about one turn counterclockwise? (it's the small screw at the top center of the picture just under the black plastic chip...)

That should solve all of the problems you just described. Mine exactly the same symptoms, and they all disappeared once the idle speed was reduced.
Yea, that's the idle screw I was talking about. At this point I've tried adjusting it to nearly it's full range and the thing still won't idle right, it also is still the engine code listed above.

Do you (or anyone with a 1zz throttle body) have the symptoms I described in my post above? Particularly the long throttle hang when you take your foot off of the gass, and the hiccup when you press down on the gas?

At this point I think I am going to buy another 1ZZ throttle body and chip swap it in my spare time. 👎
tooterLos Angeles · Feb 17, 2013#353
Originally Posted by 4/20 NEVER FORGET ↑
Yea, that's the idle screw I was talking about. At this point I've tried adjusting it to nearly it's full range and the thing still won't idle right, it also is still the engine code listed above.

Do you (or anyone with a 1zz throttle body) have the symptoms I described in my post above? Particularly the long throttle hang when you take your foot off of the gass, and the hiccup when you press down on the gas?
Yes.

I'm running a 1ZZ throttle body right now, and I had all of the exact same symptoms that you've been describing. They were all caused by the butterfly not being able to close enough for the ECU to stabilize the idle. Take the chip off and check to see if the butterfly is actually closing when you back off that little allen head screw.

I tell you mine runs way better than the stock throttle body ever did... once the butterfly was allowed to close.

At this point I think I am going to buy another 1ZZ throttle body and chip swap it in my spare time. 👎
I hope you can sort this one out before you waste money on another one that will likely do the same thing.
4/20 NEVER FORGETPortland, OR · Feb 17, 2013#354
I pulled out the reciept I have for the throttle body from the wrecking yard and it says the throttle body came from a car with an automatic transmission.... I wonder if that has anything to do with it?

EDIT: Also, the throttle body required a lot of cleaning and was obviously well-used, perhaps the electronics are dirty or need replaced anyway. I might as well do a chip-swap for that reason alone.

Tooter, you ended up chip-swapping your 1zz throttle body even though in the end you said you didn't feel like you needed too, right?
tooterLos Angeles · Feb 17, 2013#355
Originally Posted by 4/20 NEVER FORGET ↑
I pulled out the reciept I have for the throttle body from the wrecking yard and it says the throttle body came from a car with an automatic transmission.... I wonder if that has anything to do with it?
I suspected that of mine when I was having your problems, but it was just the butterfly not being allowed to close due to the screw. Take the chip off and make sure that nothing is keeping the butterfly from resting on the idle screw. If it is, back the screw out and make sure the butterfly stop continues to rest on it.

The 1ZZ is factory set to idle a 1.8. When you put it on a 1.5, the butterfly is way too far open for the reduced air requirements of our smaller engines. So you get the crazy hunting for the right idle, the bizarre 2 second hanging throttle, and the racing 3,000 rpm cold starts.

And just an afterthought... also check for vacuum leaks. One easy way is to run the engine and take a spray bottle of water and spray the base of the throttle body, and where your manifold attaches to the head... and listen for any change in idle indicating the water is being sucked into the engine.
4/20 NEVER FORGETPortland, OR · Feb 17, 2013#356
I took some starting fluid and sprayed it around all of the places where there might be leaks and found nothing. Everything is good and tight it seems.

After thinking about it some more I decided to try backing that idle screw out even more. I probably backed it out around 2 turns total over multiple short drives in the car. Over a few drives, I got the idle quite low, right before the engine starts to shake, and then turned it back a 1/4 turn and reset the ECU. (negative terminal off of battery for 3 hours)

After reconnecting the batterym I started it up and it did the thing again where it climbs in rpm then suddenly drops, then climbs, then drops, on and on. I am used to Hondas where this indicates a bad IAC, but after reading about the design of this setup a bit, I decided to wait and see if the car could sort it out. I took a while. It did the rpm surge and drop thing for about a minute, then finally it smoothed out but was at a very high rpm. It gradually decreased over about 3-4 minutes. Finally after the car was warm the rpm settled at a nice low idle.

I just went and drove the car about 40 miles and it didn't throw a CEL. The car actually drove quite well, other than some rpm hang while creeping through a parking lot, it drove nearly perfect. I'll keep my fingers crossed, hopefully backing that idle screw way, way out from where it was fixed it. (probably not lol) Thanks for the advice. 👍
thatbryanguySC · Feb 17, 2013#357
Originally Posted by 4/20 NEVER FORGET ↑
I took some starting fluid and sprayed it around all of the places where there might be leaks and found nothing. Everything is good and tight it seems.

After thinking about it some more I decided to try backing that idle screw out even more. I probably backed it out around 2 turns total over multiple short drives in the car. Over a few drives, I got the idle quite low, right before the engine starts to shake, and then turned it back a 1/4 turn and reset the ECU. (negative terminal off of battery for 3 hours)

After reconnecting the batterym I started it up and it did the thing again where it climbs in rpm then suddenly drops, then climbs, then drops, on and on. I am used to Hondas where this indicates a bad IAC, but after reading about the design of this setup a bit, I decided to wait and see if the car could sort it out. I took a while. It did the rpm surge and drop thing for about a minute, then finally it smoothed out but was at a very high rpm. It gradually decreased over about 3-4 minutes. Finally after the car was warm the rpm settled at a nice low idle.

I just went and drove the car about 40 miles and it didn't throw a CEL. The car actually drove quite well, other than some rpm hang while creeping through a parking lot, it drove nearly perfect. I'll keep my fingers crossed, hopefully backing that idle screw way, way out from where it was fixed it. (probably not lol) Thanks for the advice. 👍
I had all of that going on and had a little thread going on MicroImage on this issue (same CEL and idling issues) but after you play with the idle screw and get it down low you have to drive it for a few days for it to really smooth out. The only problem with it now is every time I disconnect my battery the ECu has to relearn the 1zz TB and will idle high and seek that good idle by going up and down at first. After driving it for a bit it settles and smoothes. :)
jetblastNor Cal · Feb 17, 2013#358
Sounds almost like you have the hard idle (mechanical idle screw) set too low and the ECM is hunting. Maybe try turning the screw in a 1/4 turn at a time to see if you can find the sweet spot. Also, you said it was quite dirty when you got the T/B. Maybe take it back off and get some T/B cleaner and some brushes to double check your previous work. Harbor Freight has some great barrel type brush assortments which work great for getting into idle air bypass type channels (they also have inexpensive code readers so you can reset things instantly). Also make sure the butterfly is clean on all edges. You can even take the return spring off so you can "exercise" the throttle through it's range of travel to feel for any potential binding.
I have to pull my Gude T/B off today and compare the bore with my 1ZZ. If it isn't any larger, I'm gonna have to bore the opening of my Weapon R to port match. I would bet money that Garm and crew have your intake matched up much nicer.

Staring at turbo sitting on bench..............
tooterLos Angeles · Feb 17, 2013#359
Originally Posted by 4/20 NEVER FORGET ↑
I took some starting fluid and sprayed it around all of the places where there might be leaks and found nothing. Everything is good and tight it seems.

After thinking about it some more I decided to try backing that idle screw out even more. I probably backed it out around 2 turns total over multiple short drives in the car. Over a few drives, I got the idle quite low, right before the engine starts to shake, and then turned it back a 1/4 turn and reset the ECU. (negative terminal off of battery for 3 hours)

After reconnecting the batterym I started it up and it did the thing again where it climbs in rpm then suddenly drops, then climbs, then drops, on and on. I am used to Hondas where this indicates a bad IAC, but after reading about the design of this setup a bit, I decided to wait and see if the car could sort it out. I took a while. It did the rpm surge and drop thing for about a minute, then finally it smoothed out but was at a very high rpm. It gradually decreased over about 3-4 minutes. Finally after the car was warm the rpm settled at a nice low idle.

I just went and drove the car about 40 miles and it didn't throw a CEL. The car actually drove quite well, other than some rpm hang while creeping through a parking lot, it drove nearly perfect. I'll keep my fingers crossed, hopefully backing that idle screw way, way out from where it was fixed it. (probably not lol) Thanks for the advice. 👍
You're welcome... 🙂
Once the ECU learns and everything settles down you can easily fine tune the idle to get it exactly where you want it. When mine is idling, it's so smooth I can't even feel the engine running except for seeing the tach needle. 👍
suckerfaceMilwaukee, WI · Feb 18, 2013#360
That sucks that all of you are having such problems with the 030 1ZZ TB. I ran mine for almost a year, and only had that issue for 15 minutes while the ECU sorted it out. From then on, it was only a high rev on cold start, and leveled out after about 2-3 minutes.

Props to tooter for the advice given to everyone, he seems to have found the fix without the chip swap.
Captain SlowScott, LA · Feb 18, 2013#361
I can't wait to see somebody post up a dyno chart showing this manifold coupled with I/H/E :D
mazillaSan Jacinto California · Feb 18, 2013#362
Originally Posted by 4/20 NEVER FORGET ↑

My guess is I need to do a chip swap. The car doesn't drive perfect. When I am coasting off of the throttle, say at 30mph (or any mph, doesn't matter), it doesn't matter if I barely touch the throttle or hammer the throttle, the car has a tiny "hiccup" feeling, as if the throttle was partly open then it closed and then opened. It's hard to describe. Also, when I am at partial throttle and I let off the throttle, it hangs for a second or two before closing and starting to decelerate. Is that normal? I know the car did it before, but it is far more pronounced now.

I also had some problems with high idle and idle hang, but I found that adjusting the throttle screw to a higher rpm idle has fixed it. I'm idling pretty high right now, probably around 1000-1200 rpm, but I haven't gotten a check engine light since I adjusted it this way (maybe 10 miles worth of driving where it would happen immediately before) so I think I am just going to leave it for now.

What do you guys think? I thought I had the right throttle body part number, but I'm thinking a chip swap is in my future.

Chip swap won't make a difference, I've been using the 1zz with the same problems, they just don't bother me. I like the idle hang. I get it during shifting(in a stick it's handy!) at high RPM, once in a while it'll be a momentary thing going from 1-2 in a parking lot, releasing the clutch stops it right away. I deal with the issues because of the boost in performance and the adjustable idle. I keep my idle between 900-1000, I absolutely hated the idle drop when the power system had a surge(subs or AC) and was wiling to do most anything to make it stop...I'm happy as a clam.


I do notice however, if I let the ecu(p0505 code) stay on long enough the ecu will adjust the idle on it's own down to about 750 which causes an occasional stall out if I shift into neutral at something like 50-60mph coasting onto an offramp. For that reason I just use my scangauge to clear the code every couple of days when it pops up.


I drive upwards of 400 miles a week in this car.
4/20 NEVER FORGETPortland, OR · Feb 18, 2013#363
An update: a bit more tweaking and I've got this 1zz throttle body dialed in. The car drives great now, about 250 miles on the car since install. It takes about 30 seconds for the idle to climb down on cold starts and it's fine after that. I took the car out on some of my favorite roads and the new manifold/throttle body gave it a noticeable power bump, it's especially snappy coming out of tight corners in 2nd and 3rd gear while high in revs.

Overall I'm extremely happy with the upgrade! Thanks again for the advice everyone.
tooterLos Angeles · Feb 18, 2013#364
Originally Posted by 4/20 NEVER FORGET ↑
An update: a bit more tweaking and I've got this 1zz throttle body dialed in. The car drives great now, about 250 miles on the car since install. It takes about 30 seconds for the idle to climb down on cold starts and it's fine after that. I took the car out on some of my favorite roads and the new manifold/throttle body gave it a noticeable power bump, it's especially snappy coming out of tight corners in 2nd and 3rd gear while high in revs.

Overall I'm extremely happy with the upgrade! Thanks again for the advice everyone.
I'm happy for you... 🙂
The 1ZZ throttle body is one of the best bang for the buck mods you can do because it enhances all of the other mods. 👍
mazillaSan Jacinto California · Feb 18, 2013#365
Originally Posted by 4/20 NEVER FORGET ↑
An update: a bit more tweaking and I've got this 1zz throttle body dialed in. The car drives great now, about 250 miles on the car since install. It takes about 30 seconds for the idle to climb down on cold starts and it's fine after that. I took the car out on some of my favorite roads and the new manifold/throttle body gave it a noticeable power bump, it's especially snappy coming out of tight corners in 2nd and 3rd gear while high in revs.

Overall I'm extremely happy with the upgrade! Thanks again for the advice everyone.


What are you idling at?
tk-421Dagobah · Feb 19, 2013#366
Originally Posted by tooter ↑
I'm happy for you... 🙂
The 1ZZ throttle body is one of the best bang for the buck mods you can do because it enhances all of the other mods. 👍
Agreed 100% 👍

Other than the high idle at cold starts (which I'm fine with), I have nothing to complain about. It's been running great for many years, and it did in fact make the rest of my existing performance mods shine even more.

BTW, Did you guys bypass the coolant line on your 1ZZ TBs? I did it since day one with no issues so far. Just wondering if you all did the same...
cali yarisThread starterCanoga Park, CA · Feb 19, 2013#367
^ That's the free secret mod right there. Not recommended in very cold climates, though.
Captain SlowScott, LA · Feb 19, 2013#368
to be honest I really want the intake manifold...but if I'm going to get it I want the most out of it and that means running a 1ZZ throttle body....but apparently there are some idle issues associated with it.

also I refuse to keep throwing ECU codes, which someone mentioned he does up above and just clears it every few days.

that's a big bummer because I actually traded in a 325i after spending nearly 5K in one year trying to fix an idle issue. I refuse to introduce one to my Yaris.....now I've got more to think about regarding the manifold :(
tooterLos Angeles · Feb 19, 2013#369
Originally Posted by Captain Slow ↑
to be honest I really want the intake manifold...but if I'm going to get it I want the most out of it and that means running a 1ZZ throttle body....but apparently there are some idle issues associated with it.
Don't let that misconception get between you and Garm's manifold. There are absolutely no idle issues with a 1ZZ throttle body if you do a couple of simple procedures right from the get go before you install it. At startup and at idle you would never know I'm running a 1ZZ...

...until you step on the gas.

The everyday driveability and throttle response are both superb. 👍
Captain SlowScott, LA · Feb 19, 2013#370
ok, I just REALLY don't want to have to mess with idle issues again.
mazillaSan Jacinto California · Feb 19, 2013#371
If you're happy with the way the car idles stock you'll likely only be dealing with the high idle on cold starts. I wanted to idle at about 1k so the trade off of spending literally 1 second pressing buttons every couple of days is worth it. Remember, for me a couple of days is a couple hundred miles...
suckerfaceMilwaukee, WI · Feb 19, 2013#372
Originally Posted by tk-421 ↑
Agreed 100% 👍

Other than the high idle at cold starts (which I'm fine with), I have nothing to complain about. It's been running great for many years, and it did in fact make the rest of my existing performance mods shine even more.

BTW, Did you guys bypass the coolant line on your 1ZZ TBs? I did it since day one with no issues so far. Just wondering if you all did the same...
I bypassed the coolant line on mine, and I live in WI where temps regularly get into single digits for 4-5 months of the year. Zero problems.
cali yarisThread starterCanoga Park, CA · Feb 19, 2013#373
^ That's good to know.
tooterLos Angeles · Feb 19, 2013#374
The coolant hose fittings are oriented differently on the two throttle bodies...

Picture not included in this copy

I just jiggered the hoses around until they fit without kinking. 😉
mazillaSan Jacinto California · Feb 19, 2013#375
Originally Posted by TOLMACH ↑
Sorry for a stupid question: Why do you guys need to bypass the coolant lines from the TB?

Just TB preventing the original lines to be used or there is smth else?


I ran out of hose...never got back to it. I could probably do it right now I guess
4/20 NEVER FORGETPortland, OR · Feb 20, 2013#376
Originally Posted by mazilla ↑
What are you idling at?
Not sure, I have't installed my tach yet. It's quite low though, I had it where the engine was just starting to shake from the idle being too low, then I turned it back a bit and it's been great ever since.

I did not bypass the coolant line to the throttle body, we get freezing fog and occasional snow here so I didn't want to have to worry about it, so I kept the coolant lines running to the throttle body.

And Captain Slow, I can relate when it comes to worrying about idle issues, I've had idle issues with many cars in the past and they are one of the most annoying things to deal with. Other than the high idle on cold starts, I have absolutely no issues with the car idling now. Hopefully that will ease your mind a little, I wanted to post my issues here so I could get some help and as you can see, it got sorted out. At very least, you could swap back to the stock throttle body and fix any idle issues that may have came from the throttle body swap. From what I gather from the system, the idle is completely controlled by the throttle body, there isn't any bypass valves or seperate sensors on the manitfold that dictate the idle other than the throttle body. So if you were having issues, it'd be an easy fix.
Captain SlowScott, LA · Feb 20, 2013#377
Come on, somebody run to a dyno so we can see what this thing does with some I/H/E mods in place :D

I'd especially love to see the difference between the stock throttle body and the 1ZZ tb.
4/20 NEVER FORGETPortland, OR · Feb 20, 2013#378
Originally Posted by Captain Slow ↑
I'd especially love to see the difference between the stock throttle body and the 1ZZ tb.
If you look through tooter's thread, you can see the exact difference a 1ZZ throttle body makes on our cars. I imagine it wouldn't be much different, give or take a HP, depending on stock manifold/tooter/MI intake manifold.

I'll just copy-paste it over actually:

Red: stock manifold + stock 1NZ FE throttle body
Blue: tooter manifold + stock 1NZ FE throttle body
Green: tooter manifold + Corolla 1ZZ FE throttle body

Picture not included in this copy

So, 3 HP and 1.5 TQ from the throttle body. Most impressive though are in the top end, how the torque curve stays flatter longer, and the peak horsepower drops off later and slower.

I think the results will be similar regardless of choice of manifold.
tooterLos Angeles · Feb 20, 2013#379
Those dyno runs were as accurate a comparison as I could make. Each successive run reflected only one change at a time (first a manifold, and then a throttle body) with everything else exactly the same. +3/+1.5 is pretty good for a throttle body. 👍
mazillaSan Jacinto California · Feb 20, 2013#380
Originally Posted by tooter ↑
Those dyno runs were as accurate a comparison as I could make. Each successive run reflected only one change at a time (first a manifold, and then a throttle body) with everything else exactly the same. +3/+1.5 is pretty good for a throttle body. 👍


Especially when you consider the cost of the throttle body!
tooterLos Angeles · Feb 20, 2013#381
Yes. 🙂

And I just paid the going rate $125. That's pretty cheap power. 👍
Captain SlowScott, LA · Feb 20, 2013#382
I've seen them used as low as $45
Captain SlowScott, LA · Feb 20, 2013#383
important question Garm, what is the weight difference between the stock manifold and the Micro Image one? thanks.

or just what is the weight of the new item? if you don't have a stock one laying around to weigh I'm sure somebody does.
CTScottUSA, CT · Feb 20, 2013#384
Originally Posted by Captain Slow ↑
important question Garm, what is the weight difference between the stock manifold and the Micro Image one? thanks.

or just what is the weight of the new item? if you don't have a stock one laying around to weigh I'm sure somebody does.
Stock intake is 5.40 lbs.
tooterLos Angeles · Feb 20, 2013#385
Originally Posted by Captain Slow ↑
I've seen them used as low as $45
I know. But the cheap ones either look like they had the crap beat out of them or that they were flood salvage and I didn't want to take a chance. The one I got came like this with the dirt scraped off...

Picture not included in this copy

After stainless steel bead blasting it looks like this...
Picture not included in this copy
...and it performs flawlessly. 👍

Hey, how about posting some more MI manifold pictures? Who else here has one?

(Sorry for jacking your thread, Garm. The 1ZZ should have its own thread. Is there a mod here who could move it?)
4/20 NEVER FORGETPortland, OR · Feb 21, 2013#386
A couple other shots I have from installing the manifold:

Picture not included in this copy

Picture not included in this copy

As you can see it's pretty snug toward the front of the car. I had to take off the hood latch to get it in there without scratching up the runners.

Mmm manifold porn. 👍
cali yarisThread starterCanoga Park, CA · Feb 21, 2013#387
another install:

Picture not included in this copy
cali yarisThread starterCanoga Park, CA · Feb 21, 2013#388
Removing the hood latch is a good idea. You could also blue tape it thoroughly, or tape a shop rag over it. 👍
Captain SlowScott, LA · Feb 21, 2013#389
still no weight on the new manifold?
tooterLos Angeles · Feb 21, 2013#390
Originally Posted by Captain Slow ↑
still no weight on the new manifold?
I'll guess 7.5 pounds. 🙂
4/20 NEVER FORGETPortland, OR · Feb 21, 2013#391
It's made of aluminum. I'd guess it a few more pounds than stock. It's negligible.
cali yarisThread starterCanoga Park, CA · Feb 21, 2013#392
still no weight on the new manifold?
Can't wait more then 22 hours eh? 🙄

All shipped, I can't weigh one until the next batch comes in. I could've sworn I weighed one, but I can't find the number.
It's a negligible difference, maybe 1-2 pounds more than stock.
Captain SlowScott, LA · Feb 21, 2013#393
just curious, I like numbers :)
Captain SlowScott, LA · Feb 26, 2013#394
another good question, how is the positioning of the throttle body as compared to the stock piece? the reason I ask is because I'm not running an SRI or CAI, just the stock box with a TRD filter in it and I'd prefer to keep the stock intake box....but if it has to go I'd like to know about it in advance.
suckerfaceMilwaukee, WI · Feb 26, 2013#395
If you have/want to swap out your stock box, I have a filter sitting in a closet going unused I'd like to get rid of...

As it is, I'd certainly encourage a more open intake (and ideally TB) as you can REALLY hear the engine, and it's amazing.
cali yarisThread starterCanoga Park, CA · Feb 26, 2013#396
Our intake manifold works perfectly with your stock airbox. We were very careful to make this happen (one reason it took a couple extra prototypes). The throttle body isn't EXACTLY in stock position, but your stock flexible intake hose will make the adjustment just fine.
Captain SlowScott, LA · Feb 27, 2013#397
good to know Garm, I prefer the stock box as it is quieter. I've had far too many cars with roaring loud intakes and am now leaning towards quieter options. thanks.
3cyltrboOttawa · Mar 1, 2013#398
didn't like 5 or 6 manifolds get sold?, but only 2 people have written about them?

I was hoping to have more feedback.

Will
cali yarisThread starterCanoga Park, CA · Mar 1, 2013#399
4 installs have been posted so far. All positive feedback. Is there a question I can answer for you?
skeckDublin, OH, USA · Mar 2, 2013#400
Love mine. Going to dyno 3rd week in march. Made appointment today as a matter of fact. Can't wait to see what my camcon will do with this since my camcon has been running in bypass mode waiting for a proper tune. Will keep everyone posted.