Yarisworld Archive

NST (NonStopTuning) Pulleys. Info, Specs, User Data...

634 posts · 271,668 views · page 2 of 13

Replies continued

Ran KizamaCanton, GA · May 3, 2007#51
Doesn't NST have other pulleys in the works as well? If so, I think I'll wait and get them all at once.
TerrorizeToronto · May 4, 2007#52
I think they mentioned something about it being in development...or something...or was that ZPI?

Anyways...i just got my NST installed...and its great so far! I noticed the weight diff of the 2 pulleys when comparing them! The stock and NST...

Thanks Dezod and NST!!
ChinoCharlesOH · May 4, 2007#53
The plan is for 2 more pulleys to come this summer.
AstromanWenatchee, WA · May 4, 2007#54
And I am SO buying them! 👍
DezodWestern NY · May 4, 2007#55
Originally Posted by Terrorize ↑
I think they mentioned something about it being in development...or something...or was that ZPI?

Anyways...i just got my NST installed...and its great so far! I noticed the weight diff of the 2 pulleys when comparing them! The stock and NST...

Thanks Dezod and NST!!
Welcome. Glad to see all arrived well.
YarisGuyUSA · May 4, 2007#56
Originally Posted by Terrorize ↑
I think they mentioned something about it being in development...or something...or was that ZPI?

Anyways...i just got my NST installed...and its great so far! I noticed the weight diff of the 2 pulleys when comparing them! The stock and NST...

Thanks Dezod and NST!!

According to Mike of NST, they will have more products for us in the future if we support them and buy their current products.

NST FTW! Everyone else who copies them FTL! 🙌
Vic-2NZFEPanama · May 4, 2007#57
Originally Posted by nigel ↑
installed the pulley yesterday, my 1.3 yaris is really a lot faster thank before
Is your Yaris a New generation or old like the echo Hb??

I am very interested about this information becasue my car is a 1.3L 2nd generation (like the one on the signature)

Other thing is that my country is very hot so we always use air conditioner
if i get to install the pulley...will it affect in any way?

Thanks in advance
Ran KizamaCanton, GA · May 4, 2007#58
Originally Posted by ChinoCharles ↑
The plan is for 2 more pulleys to come this summer.
I think I'll wait and do them all at once then. 🙂
AstromanWenatchee, WA · May 4, 2007#59
Yeah, you could do that... But buying the CR pulley now helps fund R&D which will get the rest of the pulleys out sooner. You would also save some gas if you bought one now, my MPG improved 1-3. It would probably be more convenient though to get it all done at once. Regardless if you wait for the whole set or get it piece by piece, your going to really enjoy the results
YarisGuyUSA · May 5, 2007#60
I have the NST CR-Lite and could not be more happy with it. Better response and better MPG.

NST FTW! All other copy cats FTL! 🙌
nick1983Winnipeg Manitoba · May 5, 2007#61
Originally Posted by Galavoxx ↑
Even after it's warm I can definitely feel the engine vibrating more than before. This is only at idle.
Has anyone else had this?
YamilRSan Diego, CA · May 5, 2007#62
Originally Posted by Galavoxx ↑
Having driven the car for a few days now, here's a little update.

The good: I'm still lovin' the NST pulley. Couldn't be happier. Mid-range really is much more punchy. Feels like more than 5 hp but who knows. All I know is that it revs much faster and seems to pull harder. I can't wait for the other pulleys!!

Other than the increased performance, the car idles a little rough, especially when warming up. Even after it's warm I can definitely feel the engine vibrating more than before. This is only at idle.

I have the five speed and I've noticed that takeoff requires a little more clutch than it used to. However, once rolling, accelleration is smoother than before. The last thing is that the car doesn't want to creep as easily at low speeds which sucks in traffic. Buuutt.... accellerating away from the toll booth is a blast!!! Anyway, my 2 cents.

If I remember correctly, the manual says not to warm up the car, just take it easy till the light dissapears
Ran KizamaCanton, GA · May 7, 2007#63
I've heard mention of a harmonic balancer when it comes to pulleys. Anyone care to enlighten me as to if the pulley needs one or not?
eTiMaGoBangkok, Thailand · May 7, 2007#64
well, after now having the thing in 24 hours, I can feel a few differences from before... For one, the engine does feel more responsive, looser, easier to rev up. How can I tell? My ger-changing timing's all off and jerky now, the engine gets up to speed faster, so I'm over-revving by the time I engage the clutch the "old" way. Should take a couple of days to get adjusted.

Although, at low speeds, the engine is a little more shaky, the advantage of a havier pulley and/or flywheel is more inertia, allowing the engine to spin more smoothly... But, that's also just a matter of getting used to it.

Over all, 👍
AlphaFoxSpringfield, Mass · May 7, 2007#65
I like mine, but yes it does idle rougher sometimes when the rpms drop under 600. overall im happy with it, definatley more power throught the entire rpm range. funny thing is I really notice it when im engine breaking, it definately helps stop faster!
TerrorizeToronto · May 8, 2007#66
Yeah...i feel the same benefits in mine...
However my mechanic was telling me what i might experience after changing the pulley...and he did mention that there might be more vibration now...and there is a bit like you guys mentioned..but nothing i can't get used to..
he said its due to a lighter pulley...plus the OEM pulley had some kinda or rubber gasket on it to help dampen the vibration?
AstromanWenatchee, WA · May 8, 2007#67
No such rubber on the OEM pulley. I saved my old one and inspected. All metal & paint.
curikIndonesia · May 12, 2007#68
Mike, your link to the DIY installation is dead? Also when will you be releasing the pulley kit (WP and Alternator pulleys) ? I'm interested.
largeorangefontSo Cal, OC · May 12, 2007#69
Originally Posted by Astroman ↑
No such rubber on the OEM pulley. I saved my old one and inspected. All metal & paint.
Mine has a rubber ring between the hub and the grooved pulley ring. Most OEM pulleys do. Check yours again and you will see it, and feel it.
tk-421Dagobah · May 13, 2007#70
Originally Posted by largeorangefont ↑
Mine has a rubber ring between the hub and the grooved pulley ring. Most OEM pulleys do. Check yours again and you will see it, and feel it.
Do you think it might be possible to swap that ring with the new pulley? Would the NST still fit? Or maybe NST would like to add a rubber ring for an extra buck or two?
curikIndonesia · May 13, 2007#71
Mike, I saw another pulley kit with the wp and alternator pulleys. When will these be available?
largeorangefontSo Cal, OC · May 13, 2007#72
Originally Posted by tk-421 ↑
Do you think it might be possible to swap that ring with the new pulley? Would the NST still fit? Or maybe NST would like to add a rubber ring for an extra buck or two?
No you cant swap it out. Adding a vibration dampner to the NST would probably double its price, and add weight. Slight increase in vibration is the nature of the beast with a light, solid pulley. It was barely noticeable on my car.
YarisGuyUSA · May 15, 2007#73
A lot of these questions where brought up in the original GB thread when we all signed up for these pulleys. The vibration damper in the stock pulley is a think rubber band that hardly does much. After talking with Mike of NST on his screen name (NSTonAIM) it sounds like NST is capable of building pulleys with these rubber pieces in them, but the costs would be 3 times what they are now. The rubber is very over rated and NST has removed it in 99% of the cars they build pulleys for. The rubber has not proven to be a necessary component of the pulley in all their testing and the testimonial of thousands of aftermarket pulley users for the past 15 years or so.

.
tk-421Dagobah · May 15, 2007#74
Originally Posted by largeorangefont ↑
Adding a vibration dampner to the NST would probably double its price...
Originally Posted by YarisGuy ↑
NST is capable of building pulleys with these rubber pieces in them, but the costs would be 3 times what they are now.
I don't mind having a bit more vibration in the car, especially with the obvious advantages that a crank pulley brings to the table. I guess I just don't understand why a rubber band would increase prices so dramatically.
eTiMaGoBangkok, Thailand · May 15, 2007#75
Originally Posted by tk-421 ↑
I don't mind having a bit more vibration in the car, especially with the obvious advantages that a crank pulley brings to the table. I guess I just don't understand why a rubber band would increase prices so dramatically.

Well, I would guess a pulley is being made in a two step process (CNC mill, then anodize), but if you want a rubber insert, it would be made in a lot more steps, as two pieces of aluminium need to be made, then a piece of rubber needs to be made, and sandwiched between the aluminium. All these extra steps would need more time, and a lot more labor, and as a result, a lot more money 😉
tk-421Dagobah · May 15, 2007#76
Originally Posted by eTiMaGo ↑
Well, I would guess a pulley is being made in a two step process (CNC mill, then anodize), but if you want a rubber insert, it would be made in a lot more steps, as two pieces of aluminium need to be made, then a piece of rubber needs to be made, and sandwiched between the aluminium. All these extra steps would need more time, and a lot more labor, and as a result, a lot more money 😉
Thanks for the explanation. I just thought it was a rubber ring we were talking about here. Seems to be more like an aluminum hoagie now.

Great. Now I've got the munchies. 🙄
NonStopTuningThread starterUSA · May 17, 2007#77
Originally Posted by eTiMaGo ↑
Well, I would guess a pulley is being made in a two step process (CNC mill, then anodize), but if you want a rubber insert, it would be made in a lot more steps, as two pieces of aluminium need to be made, then a piece of rubber needs to be made, and sandwiched between the aluminium. All these extra steps would need more time, and a lot more labor, and as a result, a lot more money 😉
Thanks eTiMaGo, you pretty much nailed that one on the head.

Furthermore on the topic of the rubber damper, engine vibrations, or possible threats resulting from elimination of this rubber piece...

On a relatively understressed near stock motor with bolt ons or low amounts of boost like what most of the people on this forum probably run, a solid pulley will not have any life threatening consiquences. The factory pulley with a 2mm (less than a 1/8th inch) damper is primarily there for wide band NVH (noise vibration harshness) supression from the engine and driveline. Removing the damper and replacing it with a solid pulley will lead to minor addtional NVH but will not harm the engine. In fact, most people claim their engines seem to run smoother with NST pulleys.

The engineering reasons are that most modern engines have a short, strong crank with, a relatively high natural frequency. The dangerous second harmonic that can cause damage occurs at an rpm that this sort of engine will never see, in the area above 10,000 rpm. Even the stock damper is not tuned for attinuation at this sort of rpm so the argument is somewhat of a moot point.

Now small engines that are pushing the limit with lots of revs, wimpy cranks, super long strokes, lots of boost and dwelling in the upper rpm ranges for long periods of time can benefit from a damper designed to deal with this sort of operation but our engine is not like this, and probably very few people with this motor on this forum push the envelope that hard. How many 1.5Liter, 400HP, 11,000RPM Yaris motors do we have on these forums?

As far as I can tell, our engine has a strong and stiff bottom end that is well built for our intended use. It has an internaly balanced crankshaft which is less like to break due to torsional vibration.

There are a lot of Nissan guys who use underdrive crank pulleys in road racing series like NASA or SCCA. Road racing is much more punishing on an engine than other motorsports. The engine is subjected to run times lasting 23 to 45 minutes with the engine always in the upper ranges of its rpm limit. One race weekend is the equivlent of hundreds of 1/4 mile passes.

NST sponsors the first ever wheel to wheel Scion tC NASA Road Race car. This car has been using underdrive pulleys from NST with great results since day one.

NST also sponsors two drift cars participating in the professional US drift series, Fromula Drift. Both of these cars have been using NST pulleys with no issues of any kind for the past few seasons.

We could go on and on...

Is a solid crank pulley harmless to all engines? No it is not. Small, super high reving engines, when modified way past the simple bolt on stages may have problems. These engines reach critcal harmonics, past the 10,000 rpm range, an rpm often reached by certain race engines.

A mildly modded inline six will most likely be fine but one subjected to high rpm for long periods of time (90% of its life) with lots of boost will probably suffer. In this case , the stock balancer/damper is probably not adequate either.

Some of the older american V8 engines are externaly balanced and it is critical not to use a solid hub pulley not designed for these applications, or damage to the engine could result.

Our engines and most around here do not fall into the above catagories. Rest assured that your engines will not blow up and die or have a reduced life in street and even racing use with these parts.

I would bet that every "expert" that tells you otherwise has little personal, practical, real world experience with the subject.

.
NonStopTuningThread starterUSA · May 17, 2007#78
THE 2007 NonStopTuning RACE TEAM

Picture not included in this copy


Picture not included in this copy


Picture not included in this copy


Picture not included in this copy

DezodWestern NY · May 17, 2007#79
Go Don!!! That is the road race tC we are involved in as well. :)
GalavoxxSan Francisco · May 17, 2007#80
Again with those ladies!!! I thought we told you not to tease us anymore. 😁
TheCutsmanElk Grove Village IL · May 17, 2007#81
Originally Posted by Ran Kizama ↑
I've heard mention of a harmonic balancer when it comes to pulleys. Anyone care to enlighten me as to if the pulley needs one or not?
Yes I would like to be enlightened also👍
NonStopTuningThread starterUSA · May 17, 2007#82
Originally Posted by Galavoxx ↑
Again with those ladies!!! I thought we told you not to tease us anymore. 😁
Sorry about that sir, won't happen again!

Picture not included in this copy

🤣
ShijimaCanada · May 18, 2007#83
Great advertising, I'm hooked now. Will definitly be getting the pulleys do to the great reviews once I get my yaris.

When do you plan to release the rest of the pulleys?
eTiMaGoBangkok, Thailand · May 18, 2007#84
Originally Posted by NonStopTuning ↑
Sorry about that sir, won't happen again!

Picture not included in this copy

🤣
They can crank my pulley any time they want....
VanderkittenBerkeley, CA · May 18, 2007#85
Originally Posted by NonStopTuning ↑

I high suggest staying away from pulleys that are not anodized, as this is a very important part of the building process.
I prefer the look of anodized pulleys, but it has nothing to do with the "building" process, it's a finishing and largely cosmetic step.

**Step 1: RE-draw the stock pulley in CAD or Solid Works
Step 2: Machine out of solid block of 6061 Aluminum
Step 3: Put on car and test- If OK repeat 1,2 and go to 4
Step 4: Anodize so it looks pretty for a while!

Step 5: Sell the $hiT out of these because it is the best bang for the buck!!

**Note, this is MY patent RandD process... 🤣
NonStopTuningThread starterUSA · May 18, 2007#86
Originally Posted by Shijima ↑
Great advertising, I'm hooked now. Will definitly be getting the pulleys do to the great reviews once I get my yaris.

When do you plan to release the rest of the pulleys?
Thanks for the kind words Shijima, we appreciate it.

We have a few other goodies in the works for the Yaris community, these should be out within the next couple months. The more you guys support us, the more we can do to support your community.

Stay tuned...
ChinoCharlesOH · May 18, 2007#87
Originally Posted by Shijima ↑
Great advertising, I'm hooked now. Will definitly be getting the pulleys do to the great reviews once I get my yaris.

When do you plan to release the rest of the pulleys?
The best bit of advertising a company can do is to ship durable, high-quality products on time produced exactly to customer spec. NST does it and has been doing it for years... unlike the other guys, who can't even weld a proper exhaust. 🙄

You people defending you-know-who all over these forums spit in the face of two of our members who received shit products and shit service. I for one have more respect for our membership than to lend my support to an undeserving company.

They bought their way onto Scionlife and I'll be damned if they do the same here! If they want my respect, they can earn it. NST already has. Have yet to see one person buy an NST product and not be satisfied.
AstromanWenatchee, WA · May 18, 2007#88
👏👏👏👏👏👏👏👏
digital_stringsJakarta · May 18, 2007#90
bolt-on?
ChinoCharlesOH · May 18, 2007#91
If you're asking if a crank pulley is a bolt-on piece, it is.
PetersRedYarisThe Black Hills of South Dakota · May 18, 2007#92
[QUOTE=ChinoCharles;87174] You people defending you-know-who all over these forums spit in the face of two of our members who received shit products and shit service. I for one have more respect for our membership than to lend my support to an undeserving company. [QUOTE]

You are the man, Chino.

I'm still running my stock pully even though you-know-who gave me a free one. Ebayed it weeks ago (I'm not a gambling person)... Lost money/time and got NOTHING. 👎
Doc ZaiusOttawa, ON, Canada · May 18, 2007#93
You know, something mentioned on the ScionLife thread that I never thought about: how do aluminum pulleys stand up to extreme temperature variations? Up here in Ottawa, we have anything from -30C to +35C in a typical year (-22F to 95F). I know that cast iron is used for piano frames b/c they don't expand/contract much with temperature. If aluminum expands or contracts a lot, how will that affect the pulley performance, and will it put a lot of stress on the pulley itself...?

🆘
YarisGuyUSA · May 18, 2007#94
Originally Posted by ChinoCharles ↑
Here you go fanboys, here is what you have to look forward to. Apparently you get what you pay for.

http://www.scionlife.com/forums/viewtopic.php?t=171397

Try to find that happening to an NST pulley. I dare you.

ZPI CRACKED PULLEY FTL
Picture not included in this copy

NST ANODIZED PULLEY FTW
Picture not included in this copy

😎
ShijimaCanada · May 18, 2007#95
Originally Posted by ChinoCharles ↑
The best bit of advertising a company can do is to ship durable, high-quality products on time produced exactly to customer spec. NST does it and has been doing it for years... unlike the other guys, who can't even weld a proper exhaust. 🙄

You people defending you-know-who all over these forums spit in the face of two of our members who received shit products and shit service. I for one have more respect for our membership than to lend my support to an undeserving company.

They bought their way onto Scionlife and I'll be damned if they do the same here! If they want my respect, they can earn it. NST already has. Have yet to see one person buy an NST product and not be satisfied.
Was this an attack against me or something? If so I wasent saying what I typed sarcasticly, I lurk these forums a bit and have read nothing but good about them.

And I have no idea what your getting to in your 2nd paragraph.
ChinoCharlesOH · May 19, 2007#96
Shijima, it surely wasn't an attack on you, and if it seemed like it was I'm truly sorry. If you'd like me to explain further, feel free to PM me.
ShijimaCanada · May 19, 2007#97
No worries, my mistake.
DezodWestern NY · May 21, 2007#98
Originally Posted by ChinoCharles ↑
Here you go fanboys, here is what you have to look forward to. Apparently you get what you pay for.

http://www.scionlife.com/forums/viewtopic.php?t=171397

Try to find that happening to an NST pulley. I dare you.
Someone is doing their homework. This community is still young, and doesn't know half of the story.

NST has GREAT Customer Service and Quality. We would not deal them unless this was the case.
curikIndonesia · May 21, 2007#99
when is the pulley set coming out????????????
ChinoCharlesOH · May 21, 2007#100
Here is a bump for you drift fans... see this RETAKS AE86?

Picture not included in this copy

Well, its wearing an NST supercharger pulley kit that ups the boost from the wimpy stock 8 PSI to a whopping 17 PSI! That is more than double the POWAAAA. Tack on a 50 shot and you get one punchy drift car.

http://www.youtube.com/watch?v=nWFImilgED8

You'll see her spinning about in there. Look for the car sponsored by the other guys... oh wait, there isn't one! 👏 🙇 NST'S PRODUCTS ARE TRACK TESTED! If they can hold up on a drift car, you bet your ass they'll hold up on your Yaris!

NST FTW

1 attachment not included in this copy